Attachment structure of a non-premixed laminar methane flame

The stoichiometry and the flame structure of the leading edge, an anchor point, of a non-premixed methane flame were investigated. Local equivalence ratio at an anchor point was measured using local chemiluminescence spectra with a high spatial resolution of 17 × 450 μm. Spatially and spectrally resolved chemiluminescence measurements were carried out along the centerline and radius of the non-premixed laminar flame. The chemiluminescence spectra measured at the flame tip contained very strong luminous spectra, while these continuous background spectra disappeared at the blue flame tip region. The chemiluminescence spectra below the blue flame region were very similar to those measured in laminar premixed methane/air flames. Based on these results, the local equivalence ratio near the anchor point was calculated. Therefore, we measure the anchor point location, its shape, and stoichiometry using the flame spectra. At the anchor point, there was an island of lower equivalence ratio of 0.65, which can be estimated as the lower flammable limit of premixed laminar flame. The size of the anchor point was of horizontal elliptical shape less than 0.6 and 0.4 mm in vertical length, which located at 1.2 mm above the burner rim and inside of the rim.     

High-repetition rate measurements of temperature and thermal dissipation in a non-premixed turbulent jet flame

High-repetition rate laser Rayleigh scattering is used to study the temperature fluctuations, power spectra, gradients, and thermal dissipation rate characteristics of a non-premixed turbulent jet flame at a Reynolds number of 15,200. The radial temperature gradient is measured by a two-point technique, whereas the axial gradient is measured from the temperature time-series combined with Taylor’s hypothesis. The temperature power spectra along the jet centerline exhibit only a small inertial subrange, probably because of the low local Reynolds number (Re_δ ≈ 2000), although a larger inertial subrange is present in the spectra at off-centerline locations. Scaling the frequency by the estimated Batchelor frequency improves the collapse of the dissipation region of the spectra, but this collapse is not as good as is obtained in non-reacting jets. Probability density functions of the thermal dissipation are shown to deviate from lognormal in the low-dissipation portion of the distribution when only one component of the gradient is used. In contrast, nearly log-normal distributions are obtained along the centerline when both axial and radial components are included, even for locations where the axial gradient is not resolved. The thermal dissipation PDFs measured off the centerline deviate from log-normal owing to large-scale intermittency. At one-half the visible flame length, the radial profile of the mean thermal dissipation exhibits a peak off the centerline, whereas farther downstream the peak dissipation occurs on the centerline. The mean thermal dissipation on centerline is observed to increase linearly with downstream distance, reach a peak at the location of maximum mean centerline temperature, and then decrease for farther downstream locations. Many of these observed trends are not consistent with equivalent non-reacting turbulent jet measurements, and thus indicate the importance of understanding how heat release modifies the turbulence structure of jet flames.     

Prediction of local extinction and re-ignition effects in non-premixed turbulent combustion using a flamelet/progress variable approach

The flamelet/progress variable approach (FPVA) has been proposed by Pierce and Moin as a model for turbulent non-premixed combustion in large-eddy simulation. The filtered chemical source term in this model appears in unclosed form, and is modeled by a presumed probability density function (PDF) for the joint PDF of the mixture fraction Z and a flamelet parameter λ. While the marginal PDF of Z can be reasonably approximated by a beta distribution, a model for the conditional PDF of the flamelet parameter needs to be developed. Further, the ability of FPVA to predict extinction and re-ignition has also not been assessed. In this paper, we address these aspects of the model using the DNS database of Sripakagorn et al. It is first shown that the steady flamelet assumption in the context of FPVA leads to good predictions even for high levels of local extinction. Three different models for the conditional PDF of the flamelet parameter are tested in an a priori sense. Results obtained using a delta function to model the conditional PDF of λ lead to an overprediction of the mean temperature, even with only moderate extinction levels. It is shown that if the conditional PDF of λ is modeled by a beta distribution conditioned on Z, then FPVA can predict extinction and re-ignition effects, and good agreement between the model and DNS data for the mean temperature is observed.     

Investigation of conditional source-term estimation applied to a non-premixed turbulent flame

A turbulent combustion model, Conditional Source-term Estimation (CSE) is applied to a non-premixed turbulent jet methane flame. The conditional chemical source terms are determined on the basis of first order closure and the conditional averaged species concentrations are obtained by inverting an integral equation. The Tikhonov method is implemented for regularisation. Detailed chemistry is tabulated using the trajectory generated low-dimensional manifold method. Radiation due to the gaseous species is included. Reynolds Averaged Navier–Stokes calculations are performed using two different turbulence models. The objectives of the paper are (i) assessment of the impact of the main numerical parameters in CSE and (ii) comparison of the CSE numerical predictions with available experimental data and results from previous simulations for the selected flame. The number of CSE domains and the number of points in each CSE domain are shown to have a significant impact on the results if not selected appropriately. The present CSE calculations always converge to unique and stable predictions. The corrected k–ε model yields mixture fraction profiles in good agreement with the experimental data values for axial locations in the first half of the flame. Farther downstream, the RNG k–ε model performs better. Overall, the current predictions for the mixture fraction are in good agreement with the experimental data. The predicted temperatures using CSE and the k–ε turbulence model with a modified value of C_ε1 = 1.47 are found to be in very good agreement with the experimental data. Further, the current CSE results are of comparable quality with previous simulations using the flamelet model and conditional moment closure. Future work may include further investigation on optimal determination of the regularisation parameter and alternative regularisation techniques, soot modelling within the CSE formulation, and improved formulation of radiation.     

A DNS assessment of linear relations between filtered reaction rate,flame surface density,and scalar dissipation rate in a weakly turbulent premixed flame

Linear relations between (i) filtered reaction rate and filtered flame surface density (FSD) and (ii) filtered reaction rate and filtered scalar dissipation rate (SDR), which are widely used in Large Eddy Simulation (LES) research into premixed turbulent combustion, are examined by processing DNS data obtained from a statistically 1D planar flame under weakly turbulent conditions that are most favourable for the two approaches (flamelet combustion regime, single-step chemistry, equidiffusive mixture, adiabatic burner, and low Mach number). The analysis well supports the former approach provided that the filtered reaction rate is combined with filtered molecular transport term. In such a case, both the RANS and LES FSD approaches are based on local relations valid within weakly perturbed flamelets. Accordingly, simply recasting RANS expressions to a filtered form works well. On the contrary, while the FSD and SDR approaches appear to be basically similar at first glance, the analysis does not support the latter one, but shows that a ratio of the filtered reaction rate to the filtered SDR is strongly scattered within the studied flame brush, with its conditionally mean value varying significantly with Favre-filtered combustion progress variable. As argued in the paper, these limitations of the LES SDR approach stem from the fact that it is based on a relation valid after integration over weakly perturbed flamelets, but this relation does not hold locally within such flamelets. Consequently, when a sufficiently small filter is applied to instantaneous fields, the filter may contain only a part of the local flamelet, whereas the linear relation holds solely for the entire flamelet and may not hold within the filtered flamelet volume. Thus, the present study implies that straightforwardly recasting well-established RANS equations to a filtered form is a flawed approach if the equations are based on integral features of local burning.     

A numerical study on the formation of diffusion flame islands in a turbulent hydrogen jet lifted flame

This paper presents a numerical study on the formation of diffusion flame islands in a hydrogen jet lifted flame. A real size hydrogen jet lifted flame is numerically simulated by the DNS approach over a period of about 0.5 ms. The diameter of hydrogen injector is 2 mm, and the injection velocity is 680 m/s. The lifted flame is composed of a stable leading edge flame, a vigorously turbulent inner rich premixed flame, and a number of outer diffusion flame islands. The relatively long-term observation makes it possible to understand in detail the time-dependent flame behavior in rather large time scales, which are as large as the time scale of the leading edge flame unsteadiness. From the observation, the following three findings are obtained concerning the formation of diffusion flame islands. (1) A thin oxygen diffusion layer is developed along the outer boundary of the lifted flame, where the diffusion flame islands burn in a rather flat shape. (2) When a diffusion flame island comes into contact with the fluctuating inner rich premixed flame, combustion is intensified due to an increase in the hydrogen supply by molecular diffusion. This process also works for the production of the diffusion flame islands in the oxygen diffusion layer. (3) When a large unburned gas volume penetrates into the leading edge flame, the structure of the leading edge flame changes. In this transformation process, a diffusion flame island comes near the leading edge flame. The local deficiency of oxygen plays an important role in this production process.     

Simulation of a turbulent non-premixed flame using conditional source-term estimation with trajectory generated low-dimensional manifold

Conditional source-term estimation (CSE) is a method to close the mean chemical reaction source-term in an averaged transport equation. It is used with a trajectory generated low-dimensional manifold (TGLDM) to simulate a turbulent non-premixed flame. Integral equations are inverted for two progress variables, Y_CO2|ξ and Y_H2O|ξ, by assuming spatial homogeneity in the conditional averages. Using these two progress variables, the conditional source terms of temperature and other scalars are interpolated from the TGLDM table and mapped back into the physical space to be substituted into the transport equations. Solving a transport equation using a source-term interpolated from the TGLDM is found to improve the prediction of NO over simply interpolating the mass fraction of NO directly from the TGLDM. This method has been applied in a large eddy simulation (LES) of a turbulent non-premixed flame. Both GRI-Mech 3.0 and GRI-Mech 2.11 are found to be able to predict the temperature and major species well. However, only GRI-Mech 2.11 gives an acceptable prediction of NO. It is found that major species can be interpolated from the TGLDM table which can significantly reduce the computational cost.     

LES-CMC simulations of a turbulent bluff-body flame

The large Eddy simulations (LES)-conditional moment closure (CMC) method with detailed chemistry is applied to a bluff-body stabilized flame. Computations of the velocity and mixture fraction fields show good agreement with the experiments. Temperature and major species are well-predicted throughout the flame with the exception of the flow regions in the outer shear layer close to the nozzle where the pure mixing between hot recirculating products and fresh oxidizer cannot be captured. LES-CMC generally improves on results obtained with RANS-CMC and on LES that uses one representative flamelet to model the dependence of reactive species on mixture fraction. Simulated CO mass fractions are generally in good agreement with the experimental data although a 10% overprediction can be found at downstream positions. NO predictions show a distinct improvement over the flamelet approach, however, simulations overpredict NO mass fractions at all downstream locations due to an overprediction of temperature close to the nozzle. The potential of LES-CMC to predict unsteady finite rate effects is demonstrated by the prediction of endothermic—or “flame cooling”—regions close to the neck of the recirculation zone that favours ethylene production via the methane fuel decomposition channel.     

Compressible turbulent flame speeds of highly turbulent standing flames

In this paper we present the first measurement of turbulent burning velocities of a highly turbulent compressible standing flame induced by shock-driven turbulence in a Turbulent Shock Tube. High-speed schlieren, chemiluminescence, PIV, and dynamic pressure measurements are made to quantify flame–turbulence interaction for high levels of turbulence at elevated temperatures and pressure. Distributions of turbulent velocities, vorticity and turbulent strain are provided for regions ahead and behind the standing flame. The turbulent flame speed is directly measured for the high-Mach standing turbulent flame. From measurements of the flame turbulent speed and turbulent Mach number, transition into a non-linear compressibility regime at turbulent Mach numbers above 0.4 is confirmed, and a possible mechanism for flame generated turbulence and deflagration-to-detonation transition is established.     

Resonance of a turbulent flame in a high-frequency acoustic wave

Resonance of a weakly turbulent flame in a high-frequency acoustic wave is obtained. Because of the resonance, an acoustic wave may increase noticeably the amplitude of flame wrinkles, and the respective increase in propagation velocity of the turbulent flame front becomes larger by a factor of 10-20. The effect of resonance is especially important for turbulent flames with realistic thermal expansion propagating in a closed burning chamber, which may account for considerable scattering of experimental results on turbulent flame velocity.     

Experimental analysis of local flame extinction in a turbulent jet diffusion flame by high repetition 2-D laser techniques and multi-scalar measurements

In this paper, we present a detailed experimental study of turbulence chemistry interactions in the “DLR_B” turbulent jet diffusion flame. The flame operates on mixtures of CH₄, H₂, and N₂ in the fuel stream at Re = 22,800 and is a target flame within the TNF workshop. Extinction and re-ignition events can be tracked in real time and related to the underlying flow field phenomena and temperature fields. Time resolved measurements of OH radical concentration fields are performed in combination with temperature and velocity field measurements. For this purpose, we combined high repetition rate (33 kHz) PLIF imaging with stereoscopic PIV and double pulse Rayleigh imaging techniques. Comparisons are made with results from multi-scalar Raman/Rayleigh/LIF point measurements that reveal the thermochemical state of the flame. The large deviations from equilibrium observed on resulting OH/temperature joint pdfs could be related to strain rate and Damköhler number variations caused by turbulent flow structures leading to frequent extinctions. The 2D measurement series uniquely reveal the underlying mechanism that can lead to such events. Finally, comparisons are made to strained laminar flame calculations, which are generally found to be in good agreement with the measured data.     

A theoretical study of premixed turbulent flame development

Flame development in a statistically stationary and uniform, planar, one-dimensional turbulent flow is theoretically studied. A generalized balance equation for the mean combustion progress variable, which includes turbulent diffusion and pressure-driven transport terms, as well as the mean rate of product creation, is introduced and analyzed by invoking the sole assumption of a self-similar flame structure, well-supported by numerous experiments. The assumption offers the opportunity to simplify the problem by splitting the aforementioned partial differential equation into two ordinary differential equations, which separately model spatial variations of the progress variable and time variations of flame speed and thickness. The self-similar profile of the progress variable, obtained in numerous experiments, is theoretically predicted. Closures of the normalized pressure-driven transport term and mean rate of product creation are obtained. The closed balance equation shows that turbulent diffusion dominates during the initial stage of flame development, followed by the transition to counter-gradient transport in a sufficiently developed flame. A criterion of the transition is derived. The transition is promoted by the heat release and pressure-driven transport. Fully developed mean flame brush thickness and speed are shown to decrease when either density ratio or pressure-driven transport increases. Solutions for the development of the thickness are obtained. The development is accelerated by the pressure-driven transport and heat release.     

DNS assessment of relation between mean reaction and scalar dissipation rates in the flamelet regime of premixed turbulent combustion

The linear relation between the mean rate of product creation and the mean scalar dissipation rate, derived in the seminal paper by K.N.C. Bray [‘The interaction between turbulence and combustion’, Proceedings of the Combustion Institute, Vol. 17 (1979), pp. 223–233], is the cornerstone for models of premixed turbulent combustion that deal with the dissipation rate in order to close the reaction rate. In the present work, this linear relation is straightforwardly validated by analysing data computed earlier in the 3D Direct Numerical Simulation (DNS) of three statistically stationary, 1D, planar turbulent flames associated with the flamelet regime of premixed combustion. Although the linear relation does not hold at the leading and trailing edges of the mean flame brush, such a result is expected within the framework of Bray's theory. However, the present DNS yields substantially larger (smaller) values of an input parameter c_m (or K₂ = 1/(2c_m ? 1)), involved by the studied linear relation, when compared to the commonly used value of c_m = 0.7 (or K₂ = 2.5). To gain further insight into the issue and into the eventual dependence of c_m on mixture composition, the DNS data are combined with the results of numerical simulations of stationary, 1D, planar laminar methane–air flames with complex chemistry, with the results being reported in terms of differently defined combustion progress variables c, i.e. the normalised temperature, density, or mole fraction of CH₄, O₂, CO₂ or H₂O. Such a study indicates the dependence of c_m both on the definition of c and on the equivalence ratio. Nevertheless, K₂ and c_m can be estimated by processing the results of simulations of counterpart laminar premixed flames. Similar conclusions were also drawn by skipping the DNS data, but invoking a presumed beta probability density function in order to evaluate c_m for the differently defined c's and various equivalence ratios.     

Large-eddy simulation of a bluff-body stabilised turbulent premixed flame using the transported flame surface density approach

A premixed propane–air flame stabilised on a triangular bluff body in a model jet-engine afterburner configuration is investigated using large-eddy simulation (LES). The reaction rate source term for turbulent premixed combustion is closed using the transported flame surface density (TFSD) model. In this approach, there is no need to assume local equilibrium between the generation and destruction of subgrid FSD, as commonly done in simple algebraic closure models. Instead, the key processes that create and destroy FSD are accounted for explicitly. This allows the model to capture large-scale unsteady flame propagation in the presence of combustion instabilities, or in situations where the flame encounters progressive wrinkling with time. In this study, comprehensive validation of the numerical method is carried out. For the non-reacting flow, good agreement for both the time-averaged and root-mean-square velocity fields are obtained, and the Karman type vortex shedding behaviour seen in the experiment is well represented. For the reacting flow, two mesh configurations are used to investigate the sensitivity of the LES results to the numerical resolution. Profiles for the velocity and temperature fields exhibit good agreement with the experimental data for both the coarse and dense mesh. This demonstrates the capability of LES coupled with the TFSD approach in representing the highly unsteady premixed combustion observed in this configuration. The instantaneous flow pattern and turbulent flame behaviour are discussed, and the differences between the non-reacting and reacting flow are described through visualisation of vortical structures and their interaction with the flame. Lastly, the generation and destruction of FSD are evaluated by examining the individual terms in the FSD transport equation. Localised regions where straining, curvature and propagation are each dominant are observed, highlighting the importance of non-equilibrium effects of FSD generation and destruction in the model afterburner.     

Simulation of flame lift-off on a diesel jet using a generalized flame surface density modeling approach

A generalized flame surface density modelling approach is presented to simulate the transient ignition and flame stabilization of a diesel jet flame, for which experimental data are available. The approach consists of four submodels: a mixing model, a generalized flame surface density model, a generalized progress variable model, and a chemistry model. A database containing the laminar model reaction rates per unit generalized flame surface density is generated by solving the unsteady flamelet equations. The RANS-CFD code solves for the mean flame surface density and mean progress variable. The coupling of the models is done via the progress variable and the scalar dissipation rate. The proposed approach is found to be adapted to simulate such a lifted flame and yields good trend agreement for ignition delay and flame lift-off vs. liquid penetration. These first promising results are encouraging to further explore and to apply this method to a more industrial configuration such as a diesel engine.     

A DNS study of the physical mechanisms associated with density ratio influence on turbulent burning velocity in premixed flames

Data obtained in 3D direct numerical simulations of statistically planar, 1D weakly turbulent flames characterised by different density ratios σ are analysed to study the influence of thermal expansion on flame surface area and burning rate. Results show that, on the one hand, the pressure gradient induced within a flame brush owing to heat release in flamelets significantly accelerates the unburned gas that deeply intrudes into the combustion products in the form of an unburned mixture finger, thus causing large-scale oscillations of the burning rate and flame brush thickness. Under the conditions of the present simulations, the contribution of this mechanism to the creation of the flame surface area is substantial and is increased by σ, thus implying an increase in the burning rate by σ. On the other hand, the total flame surface areas simulated at σ = 7.53 and 2.5 are approximately equal. The apparent inconsistency between these results implies the existence of another thermal expansion effect that reduces the influence of σ on the flame surface area and burning rate. Investigation of the issue shows that the flow acceleration by the combustion-induced pressure gradient not only creates the flame surface area by pushing the finger tip into the products, but also mitigates wrinkling of the flame surface (the side surface of the finger) by turbulent eddies. The latter effect is attributed to the high-speed (at σ = 7.53) axial flow of the unburned gas, which is induced by the axial pressure gradient within the flame brush (and the finger). This axial flow acceleration reduces the residence time of a turbulent eddy in an unburned zone of the flame brush (e.g. within the finger). Therefore, the capability of the eddy for wrinkling the flamelet surface (e.g. the side finger surface) is weakened owing to a shorter residence time.     

Nonlinear hydrodynamic and thermoacoustic oscillations of a bluff-body stabilised turbulent premixed flame

Turbulent premixed flames often experience thermoacoustic instabilities when the combustion heat release rate is in phase with acoustic pressure fluctuations. Linear methods often assume a priori that oscillations are periodic and occur at a dominant frequency with a fixed amplitude. Such assumptions are not made when using nonlinear analysis. When an oscillation is fully saturated, nonlinear analysis can serve as a useful avenue to reveal flame behaviour far more elaborate than period-one limit cycles, including quasi-periodicity and chaos in hydrodynamically or thermoacoustically self-excited system. In this paper, the behaviour of a bluff-body stabilised turbulent premixed propane/air flame in a model jet-engine afterburner configuration is investigated using computational fluid dynamics. For the frequencies of interest in this investigation, an unsteady Reynolds-averaged Navier–Stokes approach is found to be appropriate. Combustion is represented using a modified laminar flamelet approach with an algebraic closure for the flame surface density. The results are validated by comparison with existing experimental data and with large eddy simulation, and the observed self-excited oscillations in pressure and heat release are studied using methods derived from dynamical systems theory. A systematic analysis is carried out by increasing the equivalence ratio of the reactant stream supplied to the premixed flame. A strong variation in the global flame structure is observed. The flame exhibits a self-excited hydrodynamic oscillation at low equivalence ratios, becomes steady as the equivalence ratio is increased to intermediate values, and again exhibits a self-excited thermoacoustic oscillation at higher equivalence ratios. Rich nonlinear behaviour is observed and the investigation demonstrates that turbulent premixed flames can exhibit complex dynamical behaviour including quasiperiodicity, limit cycles and period-two limit cycles due to the interactions of various physical mechanisms. This has implications in selecting the operating conditions for such flames and for devising proper control strategies for the avoidance of thermoacoustic instability.