表面修饰中空LaF3纳米微粒的制备及其摩擦学性能

在油酸钠,十六烷基溴化铵乳液体系中合成了表面修饰中空LaF3纳米微粒.通过透射电子显微镜(TEM)、X射线衍射(XRD)、傅立叶变换红外光谱(FTIR)、热重分析(TG-DTG)、能谱分析(EDS)等测试手段对其结构和形貌进行了表征.同时在四球摩擦磨损试验机上考察了LaF3纳米微粒作为润滑油添加剂时,添加浓度和施加载荷对其执磨减摩性能的影响.结果表明,此纳米微粒的表面为油酸修饰,具有中空结构,平均粒径约17.5nm;表面修饰中空油酸/三氟化镧纳米微粒作为成品润滑油的添加剂,具有良好的抗磨性能.另外,对中空纳米微粒的形机理进行了分析.     

表面修饰中空LaF3纳米微粒的制备及其摩擦学性能

在油酸钠/十六烷基溴化铵乳液体系中合成了表面修饰中空LaF3纳米微粒. 通过透射电子显微镜(TEM)、X射线衍射(XRD)、傅立叶变换红外光谱(FTIR)、热重分析(TG-DTG)、能谱分析(EDS)等测试手段对其结构和形貌进行了表征. 同时在四球摩擦磨损试验机上考察了LaF3纳米微粒作为润滑油添加剂时, 添加浓度和施加载荷对其抗磨减摩性能的影响. 结果表明, 此纳米微粒的表面为油酸修饰, 具有中空结构, 平均粒径约17.5 nm; 表面修饰中空油酸/三氟化镧纳米微粒作为成品润滑油的添加剂, 具有良好的抗磨性能. 另外, 对中空纳米微粒的形成机理进行了分析.     

镧对含镍铟铝青铜组织和性能的影响

本文用金相观察、微差热分析、X射线衍射分析和硬度测量等方法,研究了镧对含少量镍、铟的铝青铜合金组织和性能的影响。结果表明,合金的晶粒尺寸明显减小,α相区缩小并改善了合金的热处理效果。     

稀土与芳香胺及其氮氧化物配合物的研究(Ⅲ)——稀土硝酸盐与2,2′-联喹啉-N,N′二氧化物配合物的合成和性质

本文报道了镧、铈、镨、钕、钐硝酸盐与2,2’-联喹啉-N,N’二氧化物固体配合物的合成及其化学组成的测定,并对配合物的红外光谱、紫外光谱、荧光光谱、摩尔电导、差热-热重分析、X射线衍射等性质进行了研究。     

溴氢氧化镧的合成及结构

在常温常压下由溴氧化镧与水蒸汽反应合成了溴氢氧化镧,用示差热分析和热失重分析方法研究了溴氢氧化镧的热分解过程--在空气中于360-405℃,在氮气流中于315-347℃热分解,脱水后生成溴氧化镧。用粉末X射线衍射确定了本实验所合成的溴氢氧化镧(La(OH)₂Br)的晶体结构,是斜方晶系,a=8.9064Å,b=13.024Å,c=5.5630Å。讨论了溴氢氧化镧的有关化学性质。     

三个二维镧系配合物的结构、荧光和磁性

在溶剂热的条件下,以2,2-双(羟甲基)丙酸(Hdmpa)为配体制备了 3个新的二维镧系配合物[Ln2(dmpa)4]Cl2,其中Ln=Eu(1)、Tb(2)、Dy(3),并通过红外光谱、元素分析、粉末X射线衍射、热重分析和单晶X射线衍射对配合物进行了表征.这3个配合物是同构的,它们的Ln(Ⅲ)离子通过羧基桥联形成了二...     

高锰酸稀土化合物的制备及性质

把CCl4中的Mn2O7加到稀土氧化物中制备了稀土高锰酸盐. 并测定了它们的化学组成, 研究了它们的红外光谱, 摩尔电导率, X射线粉末衍射及热谱性质试验了高锰酸镧对苯甲醇的氧化能力, 表明比高锰酸钾有更强的氮化能力.     

聚氧乙烯-镧系金属盐(Ln3+)的络合对聚氧乙烯形态结构的影响

采用偏光显微镜(POM)、差示扫描量热(DSC)和X 射线衍射,对聚氧乙烯(PEO)的形态结构和热物理行为随6种镧系盐对PEO的摩尔比变化的规律进行了系统的探讨.结果表明,随六合水氯化镧系盐摩尔比的增加,PEO球晶行为、熔点和熔融热均逐渐减弱,当盐对PEO的摩尔比达到一定值时(如YbCl3·6H2 O :PEO =2 0 ) ,则PEO完全不结晶.不同的镧系盐对PEO结晶的影响程度不同.X 射线衍射分析的结果也表明PEO晶面衍射峰随Ln3+ 盐摩尔比的增加而下降,与POM和DSC结果一致的.结果还表明较高的干燥温度(6 0℃)对PEO与Ln3+ 的相互作用有促进作用.对比二次降温的试样与原始试样的结晶行为,降温后结晶试样的特征表明络合在降温结晶后还存在.红外结果表明PEO与Ln3+ 的相互作用是络合作用.     

碳酸镧分离富集DNA的研究

通过紫外-可见分光光度法测定了碳酸镧吸附前后溶液中的DNA含量,并计算了DNA的吸附率.通过X射线光电子能谱(XPS)与X射线衍射(XRD)分析了吸附DNA前后固相的变化.结果表明,碳酸镧对DNA有较强的吸附作用,且该过程对碳酸镧晶型未产生明显影响.通过对吸附条件的考察,发现DNA的吸附率随pH值升高而降低.最后通过磷酸二氢钾作为洗脱液将吸附的DNA回收,洗脱液中镧离子含量低于0.1×10~(-6)mol/L,对DNA的后期使用无污染.     

稀土水滑石的合成与表征（Ⅰ）

合成了稀土镧在层晶格骨架中的水滑石,经粉末X射线衍射、红外光谱、X射线光电子能谱及离子交换法进行了表征.通过催化苯酐与正己醇的酯化反应,表明样品具有催化活性.     

METHANE OXIDATIVE COUPLING: SYNERGISTIC PROMOTION OF BINARY METAL FLUORIDES TO THORIA BASED CATALYST ThO_2/LaF_3/BaF_2

Introductionlnthcstud}ofmcthaneoxidativccoupIing(0CM),aseriesofcatalystshavebeendevelopedandox}'genspeciesoncatal}'stst"ereinvestigatedextensively.Alotofpapershavebeenpublishedonthisarea.Anongkindsof0CMcatalystsmetalhalidespromotedmctaloxides.cspcciall}'Li /Mg0catal}'stl1~3l.havcbecnmostoftenstudied.Themostpromisingindustrialoncshavebeenthoughttoberarcearthoxidesbasedcatalysts.H.L.Wanelajl#Ihavesuccessfull\'madeuseofmetalfluoridesin0CM,andfoundthebcttcrpron1otingcffectofmctalfluoridcstomc…     

沉淀转化法制备多孔片状纳米LaF3

采用实验中所合成的LaPO4纳米棒为前驱体,通过沉淀的转化作用,大面积地制备了单分散的片状纳米LaF3。采用扫描电镜(SEM)、透射电镜(TEM)、X射线衍射仪(XRD)、BET(Brunauer-Emmett-Teller)测试对片状纳米LaF3的形貌、结构、相组成及表面性质进行了分析。片状纳米LaF3底边长约为40 nm,片的厚度约为35 nm,大小均一,具有多孔结构。通过改变反应溶剂,可以控制LaF3粒子的成核、生长和团聚,从而有效地调控多孔片状纳米LaF3的颗粒尺寸和分散性。对多孔片状纳米LaF3的生长机制进行了研究,结果表明LaPO4和LaF3的溶度积常数差导致了片状纳米LaF3的生成;体系中自身存在的Ostwald ripening作用使片状纳米LaF3出现了多孔结构。     

Hydrothermal preparation and luminescence of LaF3:Eu3+ nanoparticles

LaF3:Eu3+ nanoparticles were prepared by a simple hydrothermal process at low temperature and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and fluorescence spectrum. Well-dispersed nanoparticles with an average size of 30 nm and a hexagonal shape were obtained. The influences of reaction temperature and time on the preparation and luminescence of LaF3:Eu3+ nanoparticles were investigated. Luminescent quenching occurred at a much higher concentration ( approximately 25mol%) and stronger luminescent intensity than in bulk LaF3:Eu3+. Fluorescence intensity of the LaF3:Eu3+ nanoparticles varied remarkably with calcination temperatures. It was found that samples without any further calcinations can emit quite strong fluorescence.     

棒状LaF3∶Eu3+纳米晶的制备与发光性能

采用一种简单的液相反应法在室温下合成了棒状的LaF3∶Eu3+纳米晶, 对其结构和发光性能进行了表征. XRD分析结果表明, 室温下即可得到结晶良好的六方晶相的LaF3, 灼烧之后样品的衍射峰增强, 没有杂相产生. TEM照片表明, 棒状LaF3∶Eu3+纳米材料的直径为8 nm左右, 长度达到50 nm. 荧光光谱表明, 室温下合成的棒状LaF3∶Eu3+纳米晶的最强发射峰位于589 nm, 对应于Eu3+的5D0-7F1跃迁发射, 说明Eu3+占据LaF3基质中La3+晶格点的C2对称格位上. 同时Eu3+的猝灭摩尔分数为5%, 荧光寿命随着灼烧温度的升高而延长.     

Preparation process and upconversion luminescence of Er3+-Doped glass ceramics containing Ba2LaF7 nanocrystals

The preparation process and upconversion luminescence of the Er(3+)-doped glass ceramics containing Ba(2)LaF(7) nanocrystals were investigated. The formation of Ba(2)LaF(7) nanocrystals in the glass ceramics was confirmed by X-ray diffraction. Er(3+)-doped glass ceramics containing Ba(2)LaF(7) nanocrystals exhibited highly efficient upconversion luminescence in comparison with glasses. With the increase of heat treatment temperature the upconversion luminescence intensity increased gradually. The composition of glasses was also found to have significant influence on the crystallization process of glass ceramics. The mixture of Ba(2)LaF(7) and La(2)O(3) nanocrystals and the mixture of La(2)F(3) and La(2)O(3) nanocrystals in the glass ceramics could be obtained by controlling different compositions of glasses. The upconversion luminescence intensity also varied significantly with different nanocrystals in the glass ceramics.     

SiO2/LaF3:Eu3＋核壳结构发光粒子的制备与表征

采用简单的液相法合成了SiO2/LaF3:Eu3＋核壳结构发光粒子, 并对其结构及发光性能进行了表征. XRD分析表明包覆层LaF3:Eu3＋为立方晶相结构, 红外光谱表明SiO2颗粒表面有柠檬酸的修饰, 电镜照片表明合成了球形的核-壳结构的复合粒子, 包覆层厚度为10～20 nm, 光谱测试表明核-壳复合粒子与纯的LaF3:Eu3＋具有相同的发光性能, 均以589 nm附近的5D0—7F1磁偶极跃迁为最强发射峰, 说明Eu3＋在LaF3基质中占据的格位相同.     

Improvement in the luminescence properties and processability of LaF3/Ln and LaPO4/Ln nanoparticles by surface modification

The surface of lanthanide(III)-doped LaPO4 nanoparticles was modified by reaction with an alcohol, leading to a covalent bond between the ligand and the particle surface. The surface of lanthanide(III)-doped LaF3 nanoparticles was modified to alter the solubility of the nanoparticles and study the influence of surface effects on the luminescence of lanthanide ions doped in the nanoparticles. The coordinated organic ligands can be modified by a quantitative exchange reaction in solution or by using functionalized ligands during the synthesis. Variation of the ratio of ligand to core reagents had a significant influence on the size of the nanoparticles. Smaller nanoparticles were formed with a higher ligand ratio. The optical properties of these nanoparticles show a strong dependence on nanoparticle size, indicating the influence of quenching probably by CH and OH groups at or near the surface of the nanoparticle cores. The luminescence lifetime of LaF3/Eu nanoparticles varied from 6.5 to 7.4 ms for nanoparticles with an average size of 7.1 to 8.4 nm. A significant reduction of the quenching from the surface of the nanoparticles was obtained by the synthesis of core-shell nanoparticles, in which a shell of LaF3 was grown epitaxially around the doped core nanoparticles. This leads to an increase in the luminescence lifetime of the Eu3+ ion and the observation of emissions from the 5D2 energy level, in addition to emissions from the 5D1 and 5D0 levels. The quantum yield of LaF3/Ce,Tb nanoparticles could be increased from 24 to 54% by the growth of a LaF3 shell around the nanoparticles.     

LaF3纳米片和棒束的选择性合成及表征

室温条件下,以简单的液相法,通过改变氟源NaBF4和K2SiF6,制得不同形貌的LaF3纳米晶(片及棒束).X射线衍射(XRD)结果显示所得的2种不同形貌的产物均为结晶良好的六方相LaF3.场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)结果表明由NaBF4制得大量均匀、厚度约为20 am的六边形纳米片....     

Yb3+掺杂浓度对LaF3晶相及其上转换光谱的影响

LaF3微米晶的晶相(斜方相和六角相)及其上转换发光光谱可以通过精确调节Yb3+的摩尔掺杂浓度来控制。利用简单的水热法合成了Yb3+和Tm3+共掺杂的LaF3,YF3和NaYF4三种不同基质的氟化物纳米晶。XRD分析表明,当Tm3+的掺杂浓度不变,仅Yb3+的摩尔掺杂浓度从10%提高到20%,就可以使基质结构由六角相过渡到斜方相。实验结果表明,具有较大离子半径的稀土离子由于增强的偶极化率,更容易使电子云产生畸变,有利于基质斜方相结构的形成。