一个非比例循环粘塑性本构模型

本文提出地一个考虑材料非比例循环附加强效应，非比例循环加载历史产应和应变幅值历史效应的粘塑性体构模型。在该模型中，引入了对加载过程非常弹性应变幅值的记忆变量ｑ；定义了新的非比例度；引入了考虑材料非比例度的循环饱和各向同性变形阻力参量Ｑｓ；对各向同性变开引入了具有先前加载历史记忆的演化方程，将本文模型用于１Ｃｒ１８Ｎｉ９Ｔｉ不锈钢高温循环变形行为描述，其预言结果与实验结果吻合得很好，表明该模型能很好     

考虑路径相关性的非比例循环塑性本构模型

根据非比例加载下金属材料响应的延迟特性及加载路径相关性,选取沿应力迹法向的塑性应变的累积量作为非比例加载影响的度量,相应给出反映非比例附加强化的变量,并假设其模量和强化率与加载路径的几何参数相关．为反映由于非比例加载而引起的材料强化的异向效应,在Valanis的塑性内时响应方程中引入与加载路径几何性质有关的应力项,构成非比例循环塑性本构关系．对316和304不锈钢材料在一些典型非比例循环加载路径下的应力响应进行了理论预测,与Benallal等及McDowell的实验结果取得了良好的一致．     

循环软化45碳钢和循环硬化304不锈钢的棘轮行为实验研究

对循环软化45碳钢的单轴应力循环下的平均应力、应力幅值以及先前应变循环对棘轮效应的影响进行了实验研究;并对循环硬化的304不锈钢进行了多种非比例循环加载路径下路径形状、路径等效应力幅值、平均应变与平均应力对材料棘轮变形行为的影响实验．发现平均应力和应力幅值及其历史对于材料的棘轮行为都有很大的影响．     

循环塑性双曲面多轴本构模型研究

本文提出了一个考虑循环强化/软化效应、塑性应变幅历史效应以及非比例循环加载效应的双曲面模型。在模型中,引入了屈服面和极限面的演化方程;定义了循环应变路径的非比例度;给出了一套合理的确定模型参数的方法。将该模型用于调质热处理的42CrMo钢,模型预言的结果与实验结果吻合很好。     

非等温条件下非比例循环粘塑性本构描述

为了描述在非等温非比例循环加载下的循环变形行为，本文提出了一个考虑材料非比例循环附加硬化效应、非比例循环加载历史效应和温度历史效应的粘塑性本构模型．在该模型中，引入了具有三种不同演化速率的背应力演化方程；定义了新的非比例度；为了反映非比例循环历史和温度历史的影响，引入了表现各向同性变形阻力Ｑａｓｍ，并对各向同性的表现变形阻力引入了具有先前加载历史记忆的演化方程．将本文模型用于１Ｃｒ１８Ｎｉ９Ｔｉ不锈钢高温循环变形行为描述，其预言结果与实验结果吻合得很好．     

一种考虑非比例附加损伤的多轴低周疲劳模型

在实际工作环境中,机械结构往往承受着多轴非比例循环载荷.相比多轴比例循环加载,多轴非比例循环加载由于产生了附加强化现象,造成机械结构疲劳寿命下降.通过分析薄壁圆筒管件在非比例加载工况下应力应变变化规律和发生破坏位置,本文基于临界面法提出一种考虑多轴非比例附加损伤的疲劳模型.该模型将最大剪切应变幅平面作为临界面,提出一个新的附加强化因子,结合临界面上切应变幅和正应变幅组成新的多轴疲劳损伤参量.此参量不仅考虑了非比例加载下临界面上正应变幅和切应变幅对材料造成的疲劳损伤,还考虑到应变路径的变化和材料非比例加载敏感特性对材料疲劳寿命的影响.考虑到实际情况下模型所需材料附加强化系数有时难以获得的情况,给出了材料附加强化系数的有关近似计算公式.只需要材料基本力学参数便可得到材料附加强化系数,方便工程实际应用.采用8种材料的多轴疲劳寿命数据对提出的新模型进行检验,结果表明所提出的新模型与传统多轴疲劳模型相比预测寿命精度更高.     

一种考虑非比例附加损伤的多轴低周疲劳模型

在实际工作环境中,机械结构往往承受着多轴非比例循环载荷.相比多轴比例循环加载,多轴非比例循环加载由于产生了附加强化现象,造成机械结构疲劳寿命下降.通过分析薄壁圆筒管件在非比例加载工况下应力应变变化规律和发生破坏位置,本文基于临界面法提出一种考虑多轴非比例附加损伤的疲劳模型.该模型将最大剪切应变幅平面作为临界面,提出一个新的附加强化因子,结合临界面上切应变幅和正应变幅组成新的多轴疲劳损伤参量.此参量不仅考虑了非比例加载下临界面上正应变幅和切应变幅对材料造成的疲劳损伤,还考虑到应变路径的变化和材料非比例加载敏感特性对材料疲劳寿命的影响.考虑到实际情况下模型所需材料附加强化系数有时难以获得的情况,给出了材料附加强化系数的有关近似计算公式.只需要材料基本力学参数便可得到材料附加强化系数,方便工程实际应用.采用8种材料的多轴疲劳寿命数据对提出的新模型进行检验,结果表明所提出的新模型与传统多轴疲劳模型相比预测寿命精度更高.      

对316L不锈钢的非比例循环粘塑性本构描述

对循环硬化的３１６Ｌ不锈钢提出了一个考虑非比例循环加载下流动和硬化特性的粘塑性本构模型。模型中，通过随动硬化的背应力演化以各向同性阻力演化非比例循环路径及其历史的依赖关系来表征材料的非比例循环附加硬化和非比例循环流动特性，将模型用于预测３１６Ｌ不锈钢的圆形，正菱形应变路径的复杂循环变形行为，其预言结果与实验结果吻合很好。     

非比例循环塑性内时本构关系研究

在Valanis的内时本构理论的框架中,引入内结构张量以反映由于非比例加载而引起金属材料的附加等向强化及异向强化效应,同时提出材料强化程度的度量采用沿路径法线方向的塑性应变分量来描述.这些考虑的有效性已经通过用所建模型对304不锈钢材料在一些典型非比例循环加载路径下的响应进行的理论预测得到了验证;将该模型应用于U71Mn材料室温单轴棘轮行为描述中,结果显示内结构张量的引入不仅能较好地反映应变控制下的非比例附加效应,而且也能较好地反映应力控制下塑性应变的累积及变化率.     

40钢非比例循环塑性行为研究

对４０钢在拉扭循环复杂应变路径下的硬化特性和流动特性进行了实验研究。研究表明：４０钢材料的循环硬／软化不但依赖于应变路径形状，而且依赖于等效应变幅值，还具有路径历史效应；材料的塑性流动几乎不受先前路径历史的影响，仅依赖于当前应变路径形状和等效奕变幅值。     

Multiaxial cyclic deformation and non-proportional hardening employing discriminating load paths

Some novel discriminating multiaxial cyclic strain paths with incremental and random sequences were used to investigate cyclic deformation behavior of materials with low and high sensitivity to non-proportional loadings. Tubular specimens made of 1050 QT steel with no non-proportional hardening and 304L stainless steel with significant non-proportional hardening were used. 1050 QT steel was found to exhibit very similar behavior under various multiaxial loading paths, whereas significant effects of loading sequence were observed for 304L stainless steel. In-phase cycles with a random sequence of axial-torsion cycles on an equivalent strain circle were found to cause cyclic hardening levels similar to 90° out-of-phase loading of 304L stainless steel. In contrast, straining with a small increment of axial-torsion on an equivalent strain circle results in higher stress than for in-phase loading of 304L stainless steel, but the level of hardening is lower than for 90° out-of-phase loading. Tanaka’s non-proportionality parameter coupled with a Armstrong–Fredrick incremental plasticity model, and Kanazawa et al.’s empirical formulation as a representative of such empirical models were used to predict the stabilized stress response of the two materials under variable amplitude axial-torsion strain paths. Consistent results between experimental observations and predictions were obtained by employing the Tanaka’s non-proportionality parameter. In contrast, the empirical model resulted in significant over-prediction of stresses for 304L stainless steel.     

Multiscale experimental investigations about the cyclic behavior of the 304L SS

This work follows a series of experiments carried out earlier at INSA of Rouen (Hassan, T., Taleb, L., Krishna, S., 2008. Influence of non-proportional loading paths on ratcheting responses and simulations by two recent cyclic plasticity models. Int. J. Plast. 24, 1863–1889). It investigates the elastoplastic cyclic behavior of a 304L stainless steel at room temperature. In a first step the cross path effect on ratcheting is confirmed, as well as the crucial role of the loading path non-proportionality. Strain controlled tests are also conducted for different strain amplitudes and loading paths. Cross-hardening effect appears more important when the shearing sequence is followed by the axial one. Moreover for alternating axial and shearing cycles, this phenomenon occurs after each crossing sequence leading to a very significant strain hardening, at least of the same order as the one obtained after a circular strain path. Yet, the magnitude of the observed over hardening does not necessarily seem a function of the cumulated plastic strain.     

Effects of strain path shapes on non-proportional cyclic plasticity

The title problem was discussed to facilitate the formulation of constitutive models of cyclic plasticity under general states of loading. A series of plastic strain controlled cyclic tests was performed by applying combined axial force and torque to thin-walled tubular specimens of Type 316 stainless steel at room temperature. These tests consist of cyclic loading along uniaxial, torsional, cruciform, stellate in eight directions, square and circular plastic strain paths with a constant amplitude of equivalent plastic strain.The results of these tests showed that the strain-hardening depends markedly on the shape of the plastic strain path, and that the strain-hardening (measured by equivalent stress amplitudes) in the saturated state is significant in the order of circular, square, stellate, cruciform and proportional paths. It was also observed that these saturated values were independent of the less significant plastic strain cycles experienced in the past. Finally, the characteristic features of strain-hardening mechanisms under non-proportional loadings were discussed in some detail on the basis of the present results.     

Uniaxial and non-proportionally multiaxial ratcheting of SS304 stainless steel at room temperature: experiments and simulations

The uniaxial and non-proportionally multiaxial ratcheting behaviors of SS304 stainless steel at room temperature were initially researched by experiment and then were theoretically described by a cyclic constitutive model in the framework of unified visco-plasticity. The effects of cyclic stress amplitude, mean stress, and their histories on the ratcheting were experimentally investigated under uniaxial and different multiaxial loading paths. The shapes of non-proportional loading paths were linear, circular, elliptical and rhombic, respectively. In the constitutive model, the rate-dependent behavior of the material was reflected by a viscous term; the cyclic flow and cyclic hardening behaviors of the material under asymmetrical stress-controlled cycling were reflected by the evolution rules of kinematic hardening back stress and isotropic deforming resistance, respectively. The effect of loading history on the ratcheting was also considered by introducing two fading memorization functions for maximum inelastic strain amplitude and isotropic deformation resistance, respectively, into the constitutive model. The effect of multiaxial loading path on the ratcheting was reflected by a non-proportional factor defined in this work. The predicting ability of the developed model was proved to be good by comparing the simulations with corresponding experiments.     

A two-surface model describing ratchetting behaviors and transient hardening under nonproportional loading

A new superposed rule of Mroz's kinematic hardening rule and Ziegler's kinematic hardening rule based on two-surface model is proposed in the paper. Some experimental results on ratchetting of 2014-T6 aluminum alloy are predicted very well under multiaxial loading. In addition the conformability of the model is discussed for transient cyclic hardening under two kinds of nonproportional cyclic loading paths, i.e. square and rhombic path. The project supported by the National Natural Science Foundation of China     

A viscoplasticity theory applied to proportional and non-proportional cyclic loading at small strains

The small strain, isotropic, Viscoplasticity theory Based on Overstress (VBO) is modified so that the experimentally observed, complex cyclic hardening behavior under proportional and non-proportional loading with fixed as well as variable strain amplitude can be reproduced. This is accomplished by formulating a growth law for the isotropic, rate independent stress, a scalar valued state variable of VBO. The non-proportionality measure employed for modeling the effects of loading path, amplitude and prior history is Tanaka's fourth order tensor [Eur. J. Mech. Solids 13 (1994) 155]. Numerical experiments show the responses in step-up and down two amplitude tests and include further hardening after an increase in the strain amplitude. The differences in the responses to proportional and non-proportional loading including circular, square, one step and two steps are demonstrated. History dependence of the hardening is depicted. The cross hardening behavior, sudden increase in the stress level which is followed by softening after the path change are modeled well.     

304不锈钢室温和高温单轴循环塑性的实验研究

对304不锈钢进行了室温和高温单轴应变控制和应力控制下的系统循环试验。揭示和分析了循环应变幅值、平均应变及其历史和温度历史对材料应变循环特性的影响以及应力幅值、平均应力及其历史以及温度对循环棘轮行为的影响。也讨论了应变循环和应力循环间交互作用对材料循环塑性行为的影响。研究表明,无益单轴应变循环特性还是非对称单轴应力循环下的棘轮效应不仅取决于当前温度和加载状态,而且强烈依赖于其加载历史。研究得到了一些有助于304不锈钢室温和高温单轴循环行为本构描述的结果。     

考虑塑性应变记忆恢复的循环棘轮本构模型研究

在统一粘塑性循环本构理论框架下,以Ohno-Abdel-Karim非线性随动硬化模型为基础,建立了一个循环本构模型。模型通过引入塑性应变幅值记忆效应,并在塑性应变记忆项中加入恢复系数,提高了对循环硬化材料单轴棘轮行为的预言能力。将模型应用于316L不锈钢单轴棘轮行为的描述中,模拟不同平均应力、应力幅值下的棘轮应变,均与实验数据吻合较好,证明本文改进的本构模型能合理地描述循环硬化材料的单轴棘轮行为。