N-doped TiO<Subscript>2</Subscript> applied in low-temperature-based dye-sensitized solar cells

With urea as nitrogen source, N-doped TiO₂ powders were synthesized and fabricated for low-temperature dye-sensitized solar cells (DSSCs) by the method of doctor-blade, and the highest temperature of the whole process was 120 °C. SEM, TEM, XRD, DRS, and XPS were used to analyze the microstructure of the N-doped TiO₂ powders. EIS, Bode plot, UV–Vis and I–V were employed to measure the photovoltaic performance of the DSSCs. The maximum photoelectric conversion efficiency (η) was 5.18 % when the amount of the doped nitrogen was 4 %, and, when compared with the η of 4.22 % for pure TiO₂, the short circuit current was increased by 22.2 % and the efficiency was increased by 22.7 %. It has been shown that the doped nitrogen could effectively suppress TiO₂ crystal phase transition from anatase to rutile, and decrease the size of particles. Therefore, the increased photoelectric conversion efficiency of the N-doped TiO₂-based DSSC was ascribed to the more suitable crystal phase, sizes and inner structure.     

The effect of tin precursors on the formation of Zr<Subscript>0.8</Subscript>Sn<Subscript>0.2</Subscript>TiO<Subscript>4</Subscript> nano-powder by sol gel process

Different precursors can have different effects upon the properties of materials. In this paper, two different tin precursors, i.e., tin (IV) chloride pentahydrate (SnCl₄·5H₂O) and tin (IV) t-butoxide (Sn(OC₄H₉)₄) have been used to prepare Zr_0.8Sn_0.2TiO₄ powders. The dry gel and powder were characterized by Simultaneous DTA/TGA analysis (SDT), X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Accelerated surface area and porosimetry analyzer (ASAP). The results show less weight loss for dry gel from precursor SnCl₄·5H₂O than that of Sn(OC₄H₉)₄. The onset of polycrystalline ZST nano powders occurred at 450 °C from precursor SnCl₄·5H₂O which is 50 °C lower than that of Sn(OC₄H₉)₄. Even though the powders from SnCl₄·5H₂O had a specific surface area of 30.4 m²/g which is higher than that of 28.7 m²/g from Sn(OC₄H₉)₄. The crystallite size of ZST powders were about the same around 15 nm. This may be due to the powders are more aggregated in Sn(OC₄H₉)₄ system. Two major mechanisms are proposed for above differences in morphology and the formation of powders.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

Influence of ZrO<Subscript>2</Subscript> on the physicochemical properties of the ZrO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> binary system

A series of ZrO₂-TiO₂ mixed oxides with different weight ratios (5, 20, and 30% ZrO₂) were prepared by wet impregnation of TiO₂-P25 Degussa with certain amounts of ZrO(NO₃)₂·6H₂O (Fluka) dissolved in deionised water. The samples were characterized by the XRD, , , , and BET methods. An increase in ZrO₂ content shifted the phase transition temperature (anatase into rutile) toward higher temperatures. X-ray diffraction using an Anton Paar XRK900 reactor chamber indicated that, in the case of samples containing ZrO₂, an additional diffraction peak appeared after cooling down to 25°C. This peak could be attributed to a polymorph of TiO₂ such as in the single crystal of anatase or hexagonal form of TiO₂ which appears in the presence of ZrO₂. Generally, the preparation of dioxide systems can modify the properties of pure compounds or generate new catalytic sites as a result of strong interaction between ZrO₂ and TiO₂ oxides. The binary systems exhibit advantages like strong acidity, extended specific surface area, and high thermal stability in comparison with TiO₂. The article is published in the original.     

Pyrolysis study of sol-gel derived TiO2 powders: Part IV. TiO2-anatase prepared by hydrolysing titanium(IV) isopropoxide without chelating agents

An amorphous TiO₂ gel was obtained by hydrolysing titanium(IV) isopropoxide with a stoichiometric amount of water using SnCl₂ as catalyst. In these operative conditions, a TiO₂ gel matrix containing a lower fraction of organic residual was obtained with respect to samples prepared by previously modifying the titanium alkoxide precursor with chelating ligands. Dried gel powders were characterized by N₂ adsorption analyses, FT-IR and XRD measurements. Thermogravimetric (TG) and differential thermal analysis (DTA) coupled with mass spectrometric (MS) and gas chromatographic (GC) measurements were performed in order to identify the organic products released from TiO₂ gel pyrolysis. The Tg-MS semiquantitative analysis of the main evolved species allowed to describe both the chemical composition of the initial TiO₂ gel and the chemical rearrangements occurring in the matrix during heating up to its crystallisation to anatase form at 420°C.This revised version was published online in November 2005 with corrections to the Cover Date.     

Preparation of highly active photocatalyst anatase TiO<Subscript>2</Subscript> by mixed template method

TiO₂ nanocrystals with diameters 8–10 nm have been prepared through sol–gel method using a mixed template of polyethylene glycol (PEG) and cetytrimethylammonium bromide (CTAB) at low temperature. The samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution (HR) TEM and fourier transform infrared spectroscopy (FT-IR) etc. XRD analysis showed the TiO₂ photocatalysts prepared with mixed template are pure anatase. FTIR spectrum revealed that the cationic surfactant provides CTA⁺ molecules and bonds to Ti–O to prevent the condensation reaction. PEG plays a dispersant role in controlling the structure of nano-TiO₂ particles. CTAB and PEG incorporated with each other to restrain the growth of crystal nucleus and control the size of grain. The self-assembling process has been confirmed by HRTEM. PEG played different role in mixed template from the single template. The photocatalytic activity of samples was determined by using as a model reaction. The results showed that TiO₂ photocatalysts with mixed template have higher photocatalytic activity than P25.     

Fabrication and photocatalytic property of TiO<Subscript>2</Subscript> nanofibers

TiO₂ nanofibers were prepared from tetrabutyl titanate sol precursors by using electrospun method. X-ray diffraction (XRD) and atomic force microscope (AFM) were used to characterize their crystal structure and morphology feature. The results demonstrated that TiO₂ nanofibers possessed anatase phase and the average diameter of TiO₂ nanofibers was about 150 nm. The photocatalytic property of TiO₂ nanofibers was evaluated for the photodecomposition of methyl orange solution. And TiO₂ nanofibers exhibited high photocatalytic activities with transfer efficiency about 100% after 20 min.     

Trapped molecular species in N-doped TiO<Subscript>2</Subscript>

Nitrogen-doped TiO₂, a novel photocatalyst active in the decomposition of organic pollutants using visible light, contains several different types of paramagnetic centers. These are molecular species, such as NO and NO₂ radicals and other species, deeply interacting with the TiO₂ structure. All or part of these species is related to specific properties of the solid. Electron paramagnetic resonance has been employed to characterize the N-containing paramagnetic species present in N-doped anatase TiO₂ powders obtained via sol-gel synthesis. In the present work attention is focused on molecular species generated during the synthesis process and segregated in cavities of the TiO₂ structure.     

Mesoporous TiO<Subscript>2</Subscript> thin films prepared from hydrothermally treated precursor powder sols

Two series of TiO₂ thin films were prepared based on soluble precursor powders: The first run originated directly from an alcohol-based coating solution whereas for the second batch the aqueous precursor powder sol had previously undergone a hydrothermal treatment. The respective microstructures were characterized by electron microscopy, the phase evolution was monitored by X-ray diffraction. Ellipsometric porosimetry (EP) was employed to reveal changes of porosity and pore size induced by thermal treatment of the films.

Open image in new window

Soluble TiO₂ precursor powders were hydrothermally treated to yield coating solutions. Films from these sols were compared with those directly obtained by dissolving the precursor powders. Results indicate that crystallization to anatase is induced under hydrothermal conditions and the resulting films mostly maintain their porosity throughout thermal treatment. In contrast to that coatings processed from as-dissolved precursor powders undergo more extensive densification

     

Hydrothermal synthesis of (Fe,N) co-doped TiO<Subscript>2</Subscript> powders and their photocatalytic properties under visible light irradiation

(Fe, N) co-doped titanium dioxide powders have been prepared by a quick, low-temperature hydrothermal method using TiOSO₄, CO(NH₂)₂, Fe(NO₃)₃, and CN₃H₅ · HCl as starting materials. The synthesized powders were characterized by XRD, TEM, BET, XPS, and UV–Vis spectroscopy. Experimental results show that the as-synthesized TiO₂ powders are present as the anatase phase and that the N and Fe ions have been doped into the TiO₂ lattice. The specific surface area of the powders is 167.8 m²/g by the BET method and the mean grain size is about 11 nm, calculated by Scherrer’s formula. UV–Vis absorption spectra show that the edge of the photon absorption has been red-shifted up to 605 nm. The doped titanium dioxide powders had excellent photocatalytic activity during the process of photo-degradation of formaldehyde and some TVOC gases under visible light irradiation.     

Light expanded clay aggregate (LECA) as a support for TiO<Subscript>2</Subscript>, Fe/TiO<Subscript>2</Subscript>, and Cu/TiO<Subscript>2</Subscript> nanocrystalline photocatalysts: a comparative study on the structure,morphology, and activity

In this work, TiO₂ and doped TiO₂ photocatalysts (Fe/TiO₂ and Cu/TiO₂) were synthesized by the sol–gel method. The main objective of this study was to investigate the influence of dopants on the structure, morphology, and activity of the catalysts in powder and immobilized states. XRF, XRD, and SEM methods were used to characterize the catalysts. The structure and phase distribution of the nanocrystalline powders were identified by XRD. Nanoparticles crystallite size and the degree of crystallinity were affected by doping. The anatase contents of catalysts were achieved as follows: TiO₂ (5.89 %) < Fe/TiO₂ (42.17 %) < Cu/TiO₂ (70.28 %). It was indicated that the activity of the catalysts strongly depends on the anatase content. Under the same circumstances, copper-modified TiO₂ exhibited a twofold higher photocatalytic activity compared with TiO₂. The nanostructured catalysts were immobilized on light expanded clay aggregate (LECA) granules in order to investigate the effect of a novel support on the activity of the catalysts. Morphological changes are recognizable in the SEM images. Activity tests indicated that the best catalytic performance was assigned to Cu/TiO₂/LECA. After 120 min of irradiation, 61 % degradation of phenol in synthetic wastewater was achieved. The high photocatalytic activity of Cu/TiO₂/LECA confirms that LECA is as an excellent support.     

Sol-gel synthesis of ZnO/Zn<Subscript>2-x</Subscript>Fe<Subscript>x</Subscript>TiO<Subscript>4</Subscript> powders: structural properties,electrical conductivity and dielectric behavior

The aim of this work was an investigation of structural and electrical properties of ZnO/Zn_2-xFe_xTiO₄ (x?=?0.7, 1, 1.4) powders. The compounds obtained by sol-gel method are characterized by several techniques: X-ray diffraction (XRD), N₂ adsorption–desorption isotherms, scanning and transmission electron microscopy (SEM and TEM), X-ray photoelectron spectroscopy (XPS), electrical and dielectrical measurements. The XRD, SEM and XPS analysis confirmed the formation of ZnFeTiO₄ inverse spinel structure. The electrical and dielectrical properties of ZnO/Zn_2-xFe_xTiO₄ (x?=?0.7, 1, 1.4) were measured by impedance spectroscopy, revealing a decrease in the electrical conductivity and the dielectric constant with Fe content.

Open image in new window

     

Analysis of preparation of TiO<Subscript>2</Subscript> particles by diffusion flame reactor for photodegradation of phenol and toluene

TiO₂ nanoparticles were produced in the diffusion flame reactor, and the size and anatase/rutile content of TiO₂ were examined by a Particle Size Analyzer and X-ray diffraction, respectively. Increase in fuel/O₂ ratio, initial concentration of TiCl₄ or total gas flow rate causes the larger particle size and the higher rutile composition. The photocatalytic activities of TiO₂ powders were tested on the decompositions of phenol and toluene in the aqueous solution under UV irradiation. The degradation rate increases as the TiO₂ particle size decreases and as the initial concentration of phenol or toluene increases. The photodegradation rate of phenol by TiO₂ particles is higher than that of toluene at the same process conditions. The computational method was used to simulate the gas temperature, velocity and species mass fractions inside the diffusion flame reactor during synthesis of TiO₂ nanoparticles. The measured and simulated temperature results were compared on several positions above the burner and both of them show good agreements. The typical contours of TiCl₄, TiO₂ mass fractions and gas velocities in flame reactor were presented.     

Direct analysis of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> powders by total reflection X-ray fluorescence spectrometry

A direct analysis procedure for the determination of trace impurities of Ca, V, Cr, Mn, Fe, Ni, Cu, Zn and Ga in Al₂O₃ ceramic powders by total reflection X-ray fluorescence spectrometry (TXRF) is described. The powders were analysed in the form of slurries containing 1–10 mg mL^–1 of powder. The use of the procedure in the case of powders with differing grain size and for different slurry concentrations was investigated. Three different quantification possibilities were compared, namely the use of Al as a matrix component, the use of Fe as a trace element contained in the sample or of Co added in concentrations of 200 g g^–1 as internal standard. The homogeneity of elemental distributions in sample layers deposited on the TXRF quartz carriers by evaporating 5 L of the 10 mg mL^–1 slurries was studied by scanning the 4- to 5-mm-diameter spots of two samples by synchrotron radiation TXRF at Hasylab. For powders with differing graininess but mainly finer than about a few 10 m, no systematic influence of the grain size on the accuracy of the determinations of Ca, V, Fe, Ni, Cu and Zn could be observed. The measurement precision, however, seemed to be limited by inhomogeneous distributions of the trace elements in the samples as testified by the synchrotron radiation TXRF scans. Detection limits of the developed TXRF procedure for Ca, V, Cr, Mn, Fe, Ni, Cu, Zn and Ga were found to be in the 0.3–7 g g^–1 range and were shown to increase slightly with the grain size of the samples. Quantification using Al (matrix) as internal standard led to systematically higher values out of the accuracy required, whereas the other two approaches in all cases led to reliable results.Dedicated to the memory of Wilhelm Fresenius     

Formation of “monodispersed” SnO2 powders of various morphologies

Several procedures for the preparation of colloidal SnO₂ powders, consisting of particles of narrow size distribution and of various morphologies, are described. The hydrolysis of SnCl₄ aerosols in the presence of gaseous ammonia produces poorly crystalline SnO₂ spheres of modal diameters <2 m. Depending on the preparation conditions, the forced hydrolysis of acidic (HCl) SnCl₄ solutions yields either prismatic particles or spherulites composed of tiny, strongly aggregated, elongated subunits. In both cases the particles are in the nanometer size range (<100 nm) having crystalline rutile structure. Rod-like SnO₂ particles (0.3 m) of good crystallinity can be obtained by hydrolysis of SnCl₄ solutions in the presence of formamide. It is concluded that the hydrolysis of dissolved SnCl₄ tends to produce elongated SnO₂ particles which, depending on the experimental conditions, may be at different aggregation states.     

Sol-gel preparation and characterization of Co/TiO<Subscript>2</Subscript> nanoparticles: Application to the degradation of methyl orange

Cobalt doped titania nanoparticles were synthesized by sol-gel method using titanium(IV) isopropoxide and cobalt nitrate as precursors. X-Ray diffraction (XRD) results showed that titania and Co/TiO₂ nanoparticles only include anatase phase. The framework substitution of Co in TiO₂ nanoparticles was established by XRD, scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM-EDX) and Fourier transform infrared (FT-IR) techniques. Transmission electron microscopy (TEM) images confirmed the nanocrystalline nature of Co/TiO₂. The increase of cobalt doping enhanced “red-shift” in the UV-Vis absorption spectra. The dopant suppresses the growth of TiO₂ grains, agglomerates them and shifts the band absorption of TiO₂ from ultraviolet (UV) to visible region. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. Although the photocatalytic activity of undoped TiO₂ was found to be higher than that of Co/TiO₂ under UV irradiation, the presence of 0.5% Co dopant in TiO₂ resulted in a catalyst with the highest activity under visible irradiation.     

Sol–gel processing of IrO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript> mixed metal oxides based on a hexachloroiridate precursor

Mixed IrO₂–TiO₂ oxides were prepared by the sol–gel method upon acid-catalysed hydrolysis of an iridium solution in ethanol mixed with titanium tetraethoxide in ethanol. The iridium solution was obtained by reaction of the sodium hexachloroiridate(IV) precursor in the presence of sodium ethoxide in ethanol. Gels were formed in all but the high-Ir samples. Analysis of the dried gels showed minority-phase enrichment at the surface and the presence of Ir(III), while microscopy showed evidence for dispersed iridium-containing nanoparticles (1–20 nm in diameter). XRD powder patterns of the calcined material showed peaks due to a small amount of crystalline NaCl impurity which could be removed by washing. This left amorphous phases, except in the Ir:Ti 3:2 case, which showed evidence for the presence of separate crystalline oxide phases: anatase, IrO₂ and Ti _x Ir_1−x O₂.     

Photocatalysis enhancement of CaAl<Subscript>2</Subscript>O<Subscript>4</Subscript>:Eu<Superscript>2+</Superscript>, Nd<Superscript>3+</Superscript>@TiO<Subscript>2</Subscript> composite powders

CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were synthesized by a sol–gel method under mild conditions (i.e. low temperature and ambient pressure). The as-prepared powders were characterized by transmission electron microscopy (TEM) and analyzed by X-ray diffraction (XRD). The photocatalytic behavior of the TiO₂-base surfaces was evaluated by the degradation of nitrogen monoxide gas. It suggested that CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were composed of anatase titania and that CaAl₂O₄:Eu²⁺, Nd³⁺. TiO₂ particles were deposited on the surface of CaAl₂O₄:Eu²⁺, Nd³⁺ to form uniform film. CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders exhibited higher photocatalytic activity compared with pure TiO₂ under visible light. And the result also clearly indicated that the long afterglow phosphor absorbed and stored lights for the TiO₂ to remain photocatalytic activity in the dark.     

Influence of NH<Subscript>3</Subscript>-treating temperature on visible light photocatalytic activity of N-doped P<Subscript>25</Subscript>-TiO<Subscript>2</Subscript>

The influence of NH₃-treating temperature on the visible light photocatalytic activity of N-doped P₂₅-TiO₂ as well as the relationship between the surface composition structure of TiO₂ and its visible light photocatalytic activity were investigated. The results showed that N-doped P₂₅-TiO₂ treated at 600°C had the highest activity. The structure of P₂₅-TiO₂ was converted from anatase to rutile at 700°C. Moreover, no N-doping was detected at the surface of P₂₅-TiO₂. There was no simply linear relationship between the visible light photocatalytic activity and the concentration of doped nitrogen, and visible light absorption. The visible light photocatalytic activity of N-doped P₂₅-TiO₂ was mainly influenced by the synergistic action of the following factors: (i) the formation of the single-electron-trapped oxygen vacancies (denoted as V_o^·); (ii) the doped nitrogen on the surface of TiO₂; (iii) the anatase TiO₂ structure.     

The effect of anatase crystal morphology on the photocatalytic conversion of NO by TiO<Subscript>2</Subscript>-based nanomaterials

Hydrogen titanate nanotubes (H-TTNT) were synthesized by the alkali hydrothermal method followed by proton exchange and then submitted either to thermal treatment or to acid hydrothermal reaction to generate TiO₂-anatase nanocrystals of different morphologies. The samples were characterized by XRPD, TGA, sulfur analysis, N₂ physisorption, UV-Vis spectroscopy and TEM. Their photocatalytic activities were determined by measuring the NO conversion in inert gas stream passed through the powder catalyst bed under UV radiation. Incomplete transformation into anatase resulted in nanomaterials with low activity due to coexistence with H-TTNT or TiO₂-B precursors. Anatase specimens derived from H-TTNT aged in strong sulfuric acid media contained equidimensional nanoparticles, but retention of sulfate negatively affected their photocatalytic activity. Combining milder acidic pH with higher aging temperature, allowed synthesis of a sulfate free anatase with the same optical properties and specific surface area as the counterpart produced by calcination of H-TTNT at 550°C; however, the former exhibited truncated bi-pyramid nanocrystals and the other adopted the form of nanorods. This latter showed the highest photocatalytic activity for NO abatement, outperforming the benchmark photocatatyst TiO₂-P25; this improved activity was tentatively ascribed to the maximization of high energy {001} facets in anatase nanorods formed during calcination of H-TTNT.

Open image in new window