Reversed flow injection spectrophotometric determination of chlorate

An interfacing has been developed to connect a spectrophotometer with a personal computer and used as a readout system for development of a simple, rapid and sensitive reversed flow injection (rFI) procedure for chlorate determination. The method is based on the oxidation of indigo carmine by chlorate ions in an acidic solution (dil. HCl) leading to the decrease in absorbance at 610 nm. The decrease in absorbance is directly related to the chlorate concentration present in the sample solutions. Optimum conditions for chlorate were examined. A linear calibration graph over the range of 0.1-0.5 mg L⁻¹ chlorate was established with the regression equation of Y = 104.5X + 1.0, r² = 0.9961 (n = 6). The detection limit (3σ) of 0.03 mg L⁻¹, the limit of quantitation (10σ) of 0.10 mg L⁻¹ and the RSD of 3.2% for 0.3 mg L⁻¹ chlorate (n = 11) together with a sample throughput of 92 h⁻¹ were obtained. The recovery of the added chlorate in spiked water samples was 98.5 ± 3.1%. Major interferences for chlorate determination were found to be BrO₃⁻, ClO₂⁻, ClO⁻ and IO₃⁻ which were overcome by using SO₃²⁻ (as Na₂SO₃) as masking agent. The method has been successfully applied for the determination of chlorate in spiked water samples with the minimum reagent consumption of 14.0 mL h⁻¹. Good agreement between the proposed rFIA and the reference methods was found verified by Student's t-test at 95% confidence level.     

Determination of selenium using atomically imprinted polymer (AIP) and hydride generation atomic absorption spectrometry

This paper describes selenium determination based on Se⁰ preconcentration in the imprinted polymer (synthesized with 2.25 mmol SeO₂, 4-vinylpyridine and 1-vinylimidazole) with subsequent detection on-line in HG-FAAS. During the synthesis, SeO₂ is reduced to Se (0). Therefore, there are no MIP neither IIP in the present work, thus we denominated: AIP, i.e., atomically imprinted polymers. For the optimization of analytical parameters Doehlert design was used. The method presented limit of detection and limit of quantification of 53 and 177 ng L⁻¹, respectively, and linear range from 0.17 up to 6 μg L⁻¹ (r = 0.9936). The preconcentration factor (PF), consumptive index (CI) and concentration efficiency (CE) were 232; 0.06 mL and 58 min⁻¹ respectively. The proposed method was successfully applied to determine Se in Brazil nuts (0.33 ± 0.03 mg kg⁻¹), apricot (0.46 ± 0.02 mg kg⁻¹), white bean (0.47 ± 0.03 mg kg⁻¹), rice flour (0.47 ± 0.02 mg kg⁻¹) and milk powder (0.22 ± 0.01 mg kg⁻¹) samples. It was possible to do 12 analyzes per hour. Accuracy was checked and confirmed by analyzing certified reference material (DORM-2, dogfish muscle), and samples precision was satisfactory with RSD lower than 10%.     

A simplified approach to the determination of N-nitroso glyphosate in technical glyphosate using HPLC with post-derivatization and colorimetric detection

A simple and sensitive HPLC post-derivatization method with colorimetric detection has been developed for the determination of N-nitroso glyphosate in samples of technical glyphosate. Separation of the analyte was accomplished using an anionic exchange resin (2.50 mm × 4.00 mm i.d., 15 μm particle size, functional group: quaternary ammonium salt) with Na₂SO₄ 0.0075 M (pH 11.5) (flow rate: 1.0 mL min⁻¹) as mobile phase. After separation, the eluate was derivatized with a colorimetric reagent containing sulfanilamide 0.3% (w/v), [N-(1-naphtil)ethilendiamine] 0.03% (w/v) and HCl 4.5 M in a thermostatized bath at 95 °C. Detection was performed at 546 nm. All stages of the analytical procedure were optimized taking into account the concept of analytical minimalism: less operation times and costs; lower sample, reagents and energy consumption and minimal waste. The limit of detection (k = 3) calculated for 10 blank replicates was 0.04 mg L⁻¹ (0.8 mg kg⁻¹) in the solid sample which is lower than the maximum tolerable accepted by the Food and Agriculture Organization of the United Nations.     

Development of new reference materials for the determination of cadmium,chromium, mercury and lead in polycarbonate

Reference materials for quantitative determination of Cd, Cr, Hg and Pb in polycarbonate were developed. Reference materials with two concentration level of elements were prepared by adding appropriate amounts of chemicals to a blank polycarbonate base material. It was shown that ten bottles with triplicate analysis are enough to demonstrate the homogeneity of these candidate reference materials. The statistical results also showed no significant trends in both short-term stability test for four weeks and long-term stability test for twelve months. The certification of the four elements was carried out by isotope-dilution-inductively coupled plasma mass spectrometry (ID-ICP-MS) with microwave-assisted digestion. Certification of candidate reference materials in a single laboratory was confirmed with interlaboratory comparison participated by a certain number of well-recognized testing laboratories in Korea. The certified values and expanded uncertainties (k = 2) for the candidate reference material with low level and the one with high level were (51.7 ± 2.1) mg kg⁻¹ Cd, (103.8 ± 2.9) mg kg⁻¹ Cd, (98.8 ± 4.5) mg kg⁻¹ Cr, (1004 ± 49.8) mg kg⁻¹ Cr, (107.4 ± 4.6) mg kg⁻¹ Hg, (1133 ± 50.7) mg kg⁻¹ Hg, (94.8 ± 3.7) mg kg⁻¹ Pb and (988.4 ± 53.6) mg kg⁻¹ Pb, respectively. The reference materials developed in this study demonstrated their suitability for the quality assurance in Cd, Cr, Hg and Pb analysis for the implementation of RoHS Directive.     

Hybrid sequential injection-flow injection manifold for the spectrophotometric determination of total sulfite in wines using o-phthalaldehyde and gas-diffusion

A new automated spectrophotometric method for the determination of total sulfite in white and red wines is reported. The assay is based on the reaction of o-phthalaldehyde (OPA) and ammonium chloride with the analyte in basic medium under SI conditions. Upon on-line alkalization with NaOH, a blue product is formed having an absorption maximum at 630 nm. The parameters affecting the reaction - temperature, pH, ionic strength, amount concentration and volume of OPA, amount concentration of ammonium chloride, flow rate and reaction coil length - and the gas-diffusion process - sample and HCl volumes, length of mixing coil, donor flow rate - were studied. The proposed method was validated in terms of linearity (1-40 mg L⁻¹, r = 0.9997), limit of detection (c_L = 0.3 mg L⁻¹) and quantitation (c_Q = 1.0 mg L⁻¹), precision (s_r = 2.2% at 20 mg L⁻¹ sulfite, n = 12) and selectivity. The applicability of the analytical procedure was evaluated by analyzing white and red wine samples, while the accuracy as expressed by recovery experiments ranged between 96% and 106%.     

Artificial neural networks study of the catalytic reduction of resazurin: stopped-flow injection kinetic-spectrophotometric determination of Cu(II) and Ni(II)

An artificial neural network (ANN) procedure was used in the development of a catalytic spectrophotometric method for the determination of Cu(II) and Ni(II) employing a stopped-flow injection system. The method is based on the catalytic action of these ions on the reduction of resazurin by sulfide. ANNs trained by back-propagation of errors allowed us to model the systems in a concentration range of 0.5-6 and 1-15 mg l⁻¹ for Cu(II) and Ni(II), respectively, with a low relative error of prediction (REP) for each cation: REP_Cu(II) = 0.85% and REP_Ni(II) = 0.79%. The standard deviations of the repeatability (s_r) and of the within-laboratory reproducibility (s_w) were measured using standard solutions of Cu(II) and Ni(II) equal to 2.75 and 3.5 mg l⁻¹, respectively: s_r[Cu(II)] = 0.039 mg l⁻¹, s_r[Ni(II)] = 0.044 mg l⁻¹, s_w[Ni(II)] = 0.045 mg l⁻¹ and s_w[Ni(II)] = 0.050 mg l⁻¹. The ANNs-kinetic method has been applied to the determination of Cu(II) and Ni(II) in electroplating solutions and provided satisfactory results as compared with flame atomic absorption spectrophotometry method. The effect of resazurin, NaOH and Na₂S concentrations and the reaction temperature on the analytical sensitivity is discussed.     

A green analytical procedure for flow-injection determination of nitrate in natural waters

Nitrate determination in waters is generally carried out with cadmium filings and carcinogenic reagents or by reaction with phenolic compounds in highly concentrated sulfuric acid medium. In this work, it was developed a green analytical procedure for nitrate determination in natural waters based on direct spectrophotometric measurements in ultraviolet, using a flow-injection system with an anion-exchange column for separation of nitrate from interfering species. The proposed method employs only one reagent (HClO₄) in a minimum amount (equivalent to 18 μL concentrated acid per determination), and allowed nitrate determination within 0.50-25.0 mg L⁻¹, without interference of up to 200.0 mg L⁻¹ humic acid; 1.0 mg L⁻¹ NO₂⁻; 200.0 mg L⁻¹ PO₄³⁻; 75.0 mg L⁻¹ Cl⁻; 50.0 mg L⁻¹ SO₄²⁻ and 15.0 mg L⁻¹ Fe³⁺. The detection limit (99.7% confidence level) and the coefficient of variation (n = 20) were estimated as 0.1 mg L⁻¹ and 0.7%, respectively. The results obtained for natural water samples were in agreement with those achieved by the reference method based on nitrate reduction with copperized cadmium at the 95% confidence level.     

On-line analysis of volatile fatty acids in anaerobic treatment processes

In this paper, an on-line spectrofluorimetric system is proposed for a simple, rapid and accurate measurement of volatile fatty acids (VFA) in anaerobic treatment processes. The determination method is based on the derivatization of VFA with N-(1-naphthyl)ethylenediamine (EDAN) followed by a spectrofluorimetric detection of the corresponding amide. The analytical procedure is automated with a flow analysis technique, coupling multisyringe (MSFIA) and multi-pumping (MPFS) methods. Operative conditions have been investigated with a special attention paid to the activation and amidation steps and to the liquid-liquid extraction of the derivatized final product. Fluorescence intensities (λ_em = 335 nm, λ_ex = 395 nm) were found to be proportional to the concentration of VFA, expressed as acetic equivalent, in the range 19-1000 mg L⁻¹, with a detection limit (3σ) of 5.1 mg L⁻¹. Our results showed a good selectivity for VFA as compared to other organic and inorganic compounds usually found in sewage sludges. Validation of the on-line system developed has been assessed by application of the procedure to aqueous samples originating from sewage sludge treatment plants. The results were in good agreement with ion chromatography measurements.     

Direct estimation of nitrate, total and fractionated water extractable organic carbon (WEOC) in an agricultural soil using direct UV absorbance deconvolution

In this study, a multiwavelength UV spectral deconvolution (UVSD) procedure is proposed as a robust and simple procedure for direct estimation of carbon and nitrate contents in soil water extracts. Soil samples were collected from an open-air field cultivated with maize at 3 different depths, 30 cm each, between 0 and 90 cm of soil surface during a period of 7 months. Fractionation of water extractable organic carbon (WEOC) into hydrophobic (Hpo-WEOC), transphilic (Tpi-WEOC), and hydrophilic (Hpi-WEOC) fractions is performed using XAD-8 and XAD-4 resins connected in series. In order to perform UVSD, 3 representative reference spectra of WEOC fractions were selected automatically, in addition to a 4th spectrum representative of NO₃⁻ selected manually in order to compose the deconvolution basis. The restitution of UV spectra was made in the range 235-350 nm. Through exploitation of soil water extract UV spectra, it was possible in a single-step deconvolution procedure to determine the organic carbon (mg C l⁻¹) and NO₃⁻ (mg l⁻¹) concentrations and to differentiate and to quantitatively estimate carbon content of WEOC fractions. Statistical tests indicated satisfactory correlations between values estimated using UVSD and those determined by conventional reference methods for each parameter determined. The ranges of concentrations of carbon and NO₃⁻ in the soil water extracts studied are between 3.00 and 15.00 mg C l⁻¹ and 60-300 mg l⁻¹, respectively. The limits of quantification (LQ) and of detection (LD) of WEOC and NO₃⁻ were found to be 0.10 and 0.05 mg C l⁻¹, and 0.10 and 0.03 mg l⁻¹, respectively.     

Simultaneous determination of neutral nitrogen compounds in gasoline and diesel by differential pulse voltammetry

The presence of trace neutral organonitrogen compounds as carbazole and indole in derivative petroleum fuels plays an important role in the car's engine maintenance. In addition, these substances contribute to the environmental contamination and their control is necessary because most of them are potentially carcinogenic and mutagenic. For those reasons, a reliable and sensitive method was proposed for the determination of neutral nitrogen compounds in fuel samples, such as gasoline and diesel using preconcentration with modified silica gel (Merck 70-230 mesh ASTM) followed by differential pulse voltammetry (DPV) technique on a glassy carbon electrode. The electrochemical behavior of carbazole and indole studied by cyclic voltammetry (CV) suggests that their reduction occurs via a reversible electron transfer followed by an irreversible chemical reaction. Very well resolved diffusion controlled voltammetric peaks were obtained in dimethylformamide (DMF) with tetrabutylammonium tetrafluoroborate (TBAF₄ 0.1 mol L⁻¹) for indole (−2.27 V) and carbazole (−2.67 V) versus Ag|AgCl|KCl_sat reference electrode. The proposed DPV method showed a good linear response range from 0.10 to 300 mg L⁻¹ and a limit of detection (L.O.D) of 7.48 and 2.66 μg L⁻¹ for indole and carbazole, respectively. The results showed that simultaneous determination of indole and carbazole presents in spiked gasoline samples were 15.8 ± 0.3 and 64.6 ± 0.9 mg L⁻¹ and in spiked diesel samples were 9.29 ± 1 and 142 ± 1 mg L⁻¹, respectively. The recovery was evaluated and the results shown the values of 88.9 ± 0.4 and 90.2 ± 0.8% for carbazole and indole in fuel determinations. The proposed method was also compared with UV-vis spectrophotometric measures and the results obtained for the two methods were in good agreement according to the F and t Student's tests.     

Use of ion mobility spectroscopy with an ultraviolet ionization source as a vanguard screening system for the detection and determination of acetone in urine as a biomarker for cow and human diseases

An ion mobility spectrometer equipped with an ultraviolet lamp was used for the qualitative and quantitative determination of acetone in urine samples. This analyte can be used as a biomarker for some fat metabolism-related diseases in humans and cows. Samples require no pretreatment other than warming at 80 °C for 5 min, after which an N₂ stream is used to drive volatile analytes to the ion mobility spectrometer. The precision of the ensuing method, expressed as relative standard deviation (%RSD), is better in all cases than 6.7% for peak height and calculated at three levels of concentration. The analyte concentration range studied was from 5 to 80 mg L⁻¹, its limit of detection in the aqueous matrix 3 mg L⁻¹ and recoveries from spiked urine samples 109 ± 3%. The calculated reduced mobility for acetone in the urine samples, 1.75 ± 0.04 cm² V⁻¹ s⁻¹, was similar to previously reported values. Also, the results were consistent with those provided by test strips used for reference. The proposed method provides a new vanguard screening system for determining acetone in urine samples.     

Speciation of chromium in Australian fly ash

The concentrations of chromium (III) and (VI) in fly ash from nine Australian coal fired power stations were determined. Cr(VI) was completely leached by extraction with 0.01 M NaOH solution and the concentration was determined by inductively coupled plasma atomic emission spectrometry (ICP-AES). This was confirmed by determining Cr(III) and Cr(VI) in the extracts of fly ash that had been spiked with chromium salts. These analytical measurements were done using a combination of ion-exchange chromatography and ICP-AES. The elutant was 0.05 M HNO₃ containing 0.5%-CH₃OH. When the column was operated at a flow rate of 1.2 ml min⁻¹ and samples were injected by use of a sample loop with a volume of 100 μl, Cr(III) and Cr(VI) in sample solution was exclusively separated within approximately 10 min. The detection limits (3σ) were 5 ng for Cr(III) (0.050 mg l⁻¹) and 9 ng for Cr(VI) (0.090 mg l⁻¹), respectively. A relative standard deviation of 1.9% (n = 6) was obtained for the determination by IC-ICP-AES of 0.25 mg l⁻¹ Cr(III) and Cr(VI).     

Thermodynamics of chromium acetylacetonate sublimation

The equilibrium sublimation pressure Cr(acac)₃(s) = Cr(acac)₃(g) was measured in the range 320 ≤ T (K) ≤ 476 by two procedures. One of them is Knudsen's effusion procedure with mass spectrometric analysis of the composition of the gas phase, which proved to be good in measuring low pressure. The second is mass spectrometric procedure “calibrated volume method” (CVM), which helped us to expand the possibilities of the effusion method toward high pressure range. Experimental data are in good agreement with each other.For this process were obtained ln(P (Pa)) = 39.197 − 15 308.5/T, enthalpy Δ_subH° (T) = 127.28 ± 0.22 kJ mol⁻¹ and entropy Δ_subS° (T) = 230.1 ± 0.5 J mol⁻¹ K⁻¹.     

Synthesis and binding properties of a macrocycle with two binding subcavities

A large, covalent macrocycle that can be served as an artificial allosteric model was prepared in a reasonable yield (36%) through the template-directed synthesis. The macrocycle contains two topologically discrete subcavities, each of which consists of four amide NHs of pyridine-2,6-dicarboxamide units. The macrocycle strongly binds two molecules of N,N,N′,N′-tetramethylterephthalamide in positive cooperative manner by hydrogen-bonding interactions. The association constants were calculated to be K₁ = 1480 ± 90 and K₂ = 5580 ± 150 M⁻¹ with the Hill coefficient (h) of 1.6 at 25 °C in CDCl₃.     

Sorption characteristics and chromatographic separation of gold (I and III) from silver and base metal ions using polyurethane foams

The influence of different parameters on the sorption profiles of trace and ultra traces of gold (I) species from the aqueous cyanide media onto the solid sorbents ion exchange polyurethane foams (IEPUFs) and commercial unloaded polyurethane foams (PUFs) based polyether type has been investigated. The retention of gold (I) species onto the investigated solid sorbents followed a first-order rate equation with an overall rate constant k in the range 2.2-2.8 ± 0.2 s⁻¹. The sorption data of gold (I) followed Freundlich and Langmuir isotherm models. Thus, the a dual-mode of sorption mechanism involving absorption related to “weak base anion exchanger” and an added component for “surface adsorption” seems the most likely proposed dual mechanism for retention profile of gold (I) by the IEPUFs and PUFs solid sorbents. The capacity of the IEPUFs and PUFs towards gold (I) sorption calculated from the sorption isotherms was found to be 11.21 ± 1.8 and 5.29 ± 0.9 mg g⁻¹, respectively. The chromatographic separation of the spiked inorganic gold (I) from de ionized water at concentrations 5-15 μg mL⁻¹ onto the developed IEPUFs and PUFs packed columns at 10 mL min⁻¹ flow rate was successfully achieved. The retained gold (I) species were then recovered quantitatively from the IEPUFs (98.4 ± 2.4%, n = 5) and PUFs (95.4 ± 3.4%, n = 5) packed columns using perchloric acid (60 mL, 1.0 mol L⁻¹) as a proper eluating agent. Thiourea (1.0 mol L⁻¹)-H₂SO₄ (0.1 mol L⁻¹) system was also used as eluating agent for the recovery of gold (I) from IEPUFS (95.4 ± 5.4%, n = 3) and also PUFs (93.4 ± 4.4%, n = 3) packed columns. The performance of the IEPUFs and PUFs packed columns in terms of the height equivalent to the theoretical plates (HETP), number of plates (N), and critical and breakthrough capacities towards gold (I) species were evaluated. The developed IEPUFs packed column was applied successfully for complete retention and recovery (98.5 ± 2.7) of gold (III) species spiked onto tap- and industrial wastewater samples at <10 μg Au mL⁻¹ after reduction to gold (I). The IEPUFs packed column was applied satisfactorily for complete retention and recovery (98.5 ± 2.7) of total inorganic gold (I) and/or gold (III) species spiked to tap- and industrial wastewater samples at <10 μg mL⁻¹ gold. Chromatographic separation of gold (I) from silver (I) and base metal ions (Fe, Ni, Cu and Zn) using IEPUFS packed columns was satisfactorily achieved. The proposed method was applied successfully for the pre-concentration and separation from anodic slime and subsequent FAAS determination of analyte with satisfactory results (recoveries >95%, relative standard deviations <4.0%).     

Optical biosensor for the determination of BOD in seawater

An automatic sensing system was developed using an optical BOD sensing film. The sensing film consists of an organically modified silicate (ORMOSIL) film embedded with an oxygen-sensitive Ru complex. A multi-microorganisms immobilization method was developed for the BOD sensing film preparation. Three different kinds of microorganisms, Bacillus licheniformis, Dietzia maris and Marinobacter marinus from seawater, were immobilized on a polyvinyl alcohol ORMOSILs. After preconditioning, the BOD biosensor could steadily perform well up to 10 months. The linear fluctuant coefficients (R²) in the range of 0.3-40 mg L⁻¹ was 0.985 when a glucose/glutamate BOD standard was applied. The reproducible response for the BOD sensing film could be obtained within ±2.3% of the mean value in a series of 10 samples in 5.0 mg L⁻¹ BOD standard GGA solution. The effects of temperature, pH and sodium chloride concentration on the two microbial films were studied as well. The BOD sensing system was tested and applied for the BOD determination of seawater.     

Influence of hydrofluoric acid on extraction of thorium using a commercially available extraction chromatographic resin

The dependence of Th recovery on hydrofluoric acid (HF) concentration in nitric acid (HNO₃) solutions (1–5 mol/dm³) containing 1 × 10⁻⁶ mol/dm³ of Th and various concentrations of HF and the elution behavior were studied using a commercially available UTEVA (for uranium and tetravalent actinide) resin column. Thorium recovery decreased with an increase in HF concentration in the sample solutions. The concentration of HF at which Th recovery started to decrease was ∼1 × 10⁻⁴ mol/dm³ in 1 mol/dm³ HNO₃ solution, ∼1 × 10⁻³ mol/dm³ in 3 mol/dm³ HNO₃ solution, and ∼1 × 10⁻² mol/dm³ in 5 mol/dm³ HNO₃ solution. When Al(NO₃)₃ (0.2 mol/dm³) or Fe(NO₃)₃ (0.6 mol/dm³) was added as a masking agent for F⁻ to the Th solution containing 1 × 10⁻¹ mol/dm³ HF and 1 mol/dm³ HNO₃, Th recovery improved from 1.4 ± 0.3% to 95 ± 5% or 93 ± 3%. Effective extraction of Th using UTEVA resin was achieved by selecting the concentration of HNO₃ and/or adding masking agents such as Al(NO₃)₃ according to the concentration of HF in the sample solution.     

Successive determination of urinary protein and glucose using spectrophotometric sequential injection method

A new sequential injection (SI) system with spectrophotometric detections has been developed for successive determination of protein and glucose. The protein assay is based on ion-association of protein with tetrabromophenolphthalein ethyl ester (TBPE) in the presence of Triton X-100 at pH 3.2. The blue product is monitored for absorbance at 607 nm. For glucose, hydrogen peroxide, generated by the oxidation of glucose in the presence of glucose oxidase immobilized on glass beads packed in a minicolumn, is monitored using iron-catalyzed oxidation reaction of p-anisidine to form a red colored product (520 nm). The SI procedure takes advantage in performing the protein assay during the incubation period for glucose oxidation. Linear ranges were up to 10 mg dL⁻¹ human serum albumin (HSA) with a limit of detection (LOD) (3σ) of 0.3 mg dL⁻¹, and up to 12.5 mg dL⁻¹ glucose with LOD of 0.08 mg dL⁻¹. R.S.D.s (n = 11) were 2.7% and 2.5% (for 1 mg dL⁻¹ and 5 mg dL⁻¹ HSA) and 1.4% (9 mg dL⁻¹ glucose). Sample throughput for the whole assay of both protein and glucose is 6 h⁻¹. The automated system has been demonstrated for the successive assay of protein and glucose in urine samples taken from diabetic disease patients, with good agreement with the other methods. This developed SI system is an alternative automation for screening for diabetic diagnosis.     

Study of binding and denaturation dynamics of IgG and anti-IgG using dual color fluorescence correlation spectroscopy

In this article, we present a systematic study on IgG and Fab fragment of anti-IgG molecules using fluorescence auto- and cross-correlation spectroscopy to investigate their diffusion characteristics, binding kinetics, and the effect of small organic molecule, urea on their binding. Through our analysis, we found that the diffusion coefficient for IgG and Fab fragment of anti-IgG molecules were 37 ± 2 μm² s⁻¹ and 56 ± 2 μm² s⁻¹, respectively. From the binding kinetics study, the respective forward (k_a) and backward (k_d) reaction rates were (5.25 ± 0.25) × 10⁶ M⁻¹ s⁻¹ and 0.08 ± 0.005 s⁻¹, respectively and the corresponding dissociation binding constant (K_D) was 15 ± 2 nM. We also found that urea inhibits the binding of these molecules at 4 M concentration due to denaturation.     

Multi-pumping flow system for the determination of dissolved orthophosphate and dissolved organic phosphorus in wastewater samples

A multi-pumping flow system (MPFS) for the spectrophotometric determination of dissolved orthophosphate and dissolved organic phosphorus in wastewater samples is proposed. The determination of orthophosphate is based on the vanadomolybdate method. In-line ultraviolet photo-oxidation is employed to mineralise organic phosphorus to orthophosphate prior to detection. A solenoid valve allows the deviation of the flow towards the UV-lamp to carry out the determination of organic phosphorus.Calibration was found to be linear up to 20 mg P L⁻¹, with a detection limit (3s_b/S) of 0.08 mg P L⁻¹, an injection throughput of 75 injections h⁻¹ and a repeatability (R.S.D.) of 0.6% for the direct determination of orthophosphate. On the other hand, calibration graphs were linear up to 40 mg P L⁻¹, with a detection limit (3s_b/S) of 0.5 mg P L⁻¹, an injection throughput of 11 injections h⁻¹ and a repeatability (R.S.D.) inferior to 2.3% for the procedures involving UV photo-oxidation.