超声技术的基石——超声换能器的原理及设计

超声换能器是在超声频率范围内将交变的电信号转换成声信号或者将外界声场中的声信号转换为电信号的能量转换器件,它是超声技术中的关键器件,其性能好坏直接关系到超声应用技术的效果和使用范围.由于超声技术的应用范围很广,且超声新技术层出不穷,因而与此对应的超声换能器的种类也很多.文章对不同应用背景下多种类型超声换能器的原理及设计进行了阐述,分析了不同类型超声换能器的性能参数及设计要求,简要总结了超声换能器的性能参数测试方法,并对超声换能器的发展趋势进行了一定的分析.     

超声技术的基石——超声换能器的原理及设计

超声换能器是在超声频率范围内将交变的电信号转换成声信号或者将外界声场中的声信号转换为电信号的能量转换器件,它是超声技术中的关键器件,其性能好坏直接关系到超声应用技术的效果和使用范围.由于超声技术的应用范围很广,且超声新技术层出不穷,因而与此对应的超声换能器的种类也很多.文章对不同应用背景下多种类型超声换能器的原理及设计进行了阐述,分析了不同类型超声换能器的性能参数及设计要求,简要总结了超声换能器的性能参数测试方法,并对超声换能器的发展趋势进行了一定的分析.     

压电换能器阻抗匹配技术研究

超声测距传感器是由压电换能器及其收、发电路所组成的，其中压电换能器的阻抗特性直接影响着超声测距传感器的性能。为提高超声波回波信号的强度，扩大超声测距传感器的作用距离，对压电换能器的阻抗特性进行了分析与测试，设计了压电换能器的阻抗匹配电路，并进行了实验验证。     

柔性超声换能器在生物医学中的研究进展*

传统超声换能器存在体积大、表面刚性的缺点,无法用于人体复杂皮肤表面和可穿戴器件的设计。为使换能器具有灵活、体积小,满足可穿戴的特点,将其压电元件、电极和封装等各组成部分重组为柔性换能器。相比于传统换能器,它有两个优点：首先,不需要专业人员操作,可实现持续性的超声监控或治疗。其次,通过更全面的皮肤表面覆盖,扩大声场范围。在超声诊断方面,改善声信号采集,获得更全面的检测信息;在超声治疗方面,增加声能量沉积,提高疗效。柔性换能器使超声医疗应用场景多元化,可实现连续超声诊断或超声治疗。该文首先概述了其在设计和加工方面的最新进展,然后重点介绍了其在诊断和治疗方面的应用,最后讨论了这一领域所面临的挑战并对发展前景进行展望。     

磁致伸缩超声换能器阻抗匹配网络的设计

根据磁致伸缩超声换能器的等效电路模型和阻抗匹配理论,该文设计了一种优化的π型匹配网络.该网络具有调谐、变阻和滤波的功能,适用于工作在中低频超声频率范围内的磁致伸缩超声换能器系统的阻抗匹配.仿真和实验结果表明:接入该π型阻抗匹配网络后,驱动电源与换能器之间实现了最大功率传输,换能器两端电信号的波形质量得到优化,换能器激励...     

超声数字式相控阵换能器动态聚集系统研制

本文是研制超声相控阵换能器动态聚焦系统,它包括数字式多通道信号发射系统和两种超声相控阵换能器。用数字式多通道信号发射系统产生多路数字信号,通过改变每路信号的时延（相位）,控制相控换阵换能器的各个阵元,使它们发出的声束在空间某点聚焦。我们对这两种相控阵进行了实验测量,结果表明,用数字控制的相控阵换能器,可以实现精密的动态聚焦,并可取得良好的聚焦效果。     

功率超声振动系统的研究进展

功率超声振动系统是功率超声技术中的关键部分,其主要部分包括功率超声换能器、超声变幅杆以及超声工具头或超声辐射器。本文就功率超声换能振动系统设计中经常遇到的一些关键问题进行了简要的归纳和总结,目的在于为功率超声换能器的优化设计和性能改善提供一些有用的设计指南和解决措施。同时,对一些新的功率超声振动系统进行了介绍,并简要分析了其发展趋势和应用领域。     

测试大功率超声清洗机功率和效率的简易方法

从大功率超声清洗机电源输入到换能器的电流、电压波形皆非正弦波形。采用本文介绍的求和近似法,可以测试电流、电压的有效值以及平均功率。我们用求和近似法对大功率超声清洗机电源的电流、电压、电功率以及输入到超声换能器的电流、电压、电功率进行了测试,并用量热法对清洗槽获得的声功率也进行了测试。由测试结果计算出电源和超声换能器的效率。与已发表的结果比较接近。该方法可靠、直观、而且成本低,适合于生产厂家在现场进行测试与实验。     

cMUT阵元的声学分析与环形扫描成像

电容式微机械超声换能器(cMUT)具有宽带宽、灵敏度高、机械阻抗低和与电子电路集成制造等优点.由于超声换能器声场设计的好坏决定了成像质量的优劣,为了明确阵元参数与辐射声场的关系,该文对不同的阵元参数进行了计算仿真.与压电陶瓷超声换能器的结构不同,cMUT阵元是由多个电容单元(cell)并联构成.因此分析了cell的半径...     

电容MEMS超声换能器研究进展

MEMS(micro-electromechanical systems)超声换能器(MEMS ultrasonic transducer,简称MUT)是采用微电子和微机械加工技术制作的新型超声换能器。与传统超声换能器相比,MUT具有体积小、重量轻、成本低、功耗低、可靠性高、频率控制灵活、频带宽、灵敏度高以及易于与电路集成和实现智能化等特点。是超声换能器的重要的研究方向之一。MUT的研究主要包括压电MUT(piezoelectric MUT,简称PMUT)和电容MUT(capacitiveMUT,简称CMUT)两个方面。本文概述了CMUT研究的发展进程和研究成果,展望了CMUT的研究和应用前景。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.