A protophilic solvent‐assisted solvothermal approach to Cu‐BTC for enhanced CO2 capture

Cu‐BTC–ethylenediamine (EDA)/polyethyleneimine (PEI) adsorbents were synthesized using a protophilic solvent‐assisted solvothermal method. EDA was introduced to enhance the degree of activation due to its lower boiling point allowing it to be removed easily compared with dimethylformamide. A contrast experiment was done by introducing PEI to the solvothermal solution considering its higher boiling point. Powder X‐ray diffraction, scanning electron microscopy and Raman spectroscopic characterizations were performed to investigate the effect of EDA/PEI on crystallinity and morphology of the adsorbents. ¹H NMR characterization and elemental analysis were performed to study the removal rate of organic guest molecules and the degree of activation. Nitrogen physical adsorption and CO₂ adsorption isotherms were used to measure the surface area and CO₂ adsorption capacities. The CO₂ adsorption mechanism of the synthesized adsorbents is mainly dependent on physisorption determined by surface area. Furthermore, open metal sites generated by the enhancement of degree of activation also promote the CO₂ adsorption performance. Therefore, adsorbents synthesized using the protophilic solvent‐assisted solvothermal method exhibit excellent CO₂ adsorption performance. Copyright © 2015 John Wiley & Sons, Ltd.     

Crystal Dynamics in Multi‐stimuli‐Responsive Entangled Metal–Organic Frameworks

An understanding of solid‐state crystal dynamics or flexibility in metal–organic frameworks (MOFs) showing multiple structural changes is highly demanding for the design of materials with potential applications in sensing and recognition. However, entangled MOFs showing such flexible behavior pose a great challenge in terms of extracting information on their dynamics because of their poor single‐crystallinity. In this article, detailed experimental studies on a twofold entangled MOF ( f‐MOF‐1) are reported, which unveil its structural response toward external stimuli such as temperature, pressure, and guest molecules. The crystallographic study shows multiple structural changes in f‐MOF‐1 , by which the 3 D net deforms and slides upon guest removal. Two distinct desolvated phases, that is, f‐MOF‐1 a and f‐MOF‐1 b , could be isolated; the former is a metastable one and transformable to the latter phase upon heating. The two phases show different gated CO₂ adsorption profiles. DFT‐based calculations provide an insight into the selective and gated adsorption behavior with CO₂ of f‐MOF‐1 b . The gate‐opening threshold pressure of CO₂ adsorption can be tuned strategically by changing the chemical functionality of the linker from ethanylene (?CH₂?CH₂?) in f‐MOF‐1 to an azo (?N=N?) functionality in an analogous MOF, f‐MOF‐2 . The modulation of functionality has an indirect influence on the gate‐opening pressure owing to the difference in inter‐net interaction. The framework of f‐MOF‐1 is highly responsive toward CO₂ gas molecules, and these results are supported by DFT calculations.     

Copper–Organic Framework Fabricated with CuS Nanoparticles: Synthesis,Electrical Conductivity,and Electrocatalytic Activities for Oxygen Reduction Reaction

To apply electrically nonconductive metal–organic frameworks (MOFs) in an electrocatalytic oxygen reduction reaction (ORR), we have developed a new method for fabricating various amounts of CuS nanoparticles (nano‐CuS) in/on a 3D Cu–MOF, [Cu₃(BTC)₂?(H₂O)₃] (BTC=1,3,5‐benzenetricarboxylate). As the amount of nano‐CuS increases in the composite, the electrical conductivity increases exponentially by up to circa 10⁹‐fold, while porosity decreases, compared with that of the pristine Cu‐MOF. The composites, nano‐CuS(x wt %)@Cu‐BTC, exhibit significantly higher electrocatalytic ORR activities than Cu‐BTC or nano‐CuS in an alkaline solution. The onset potential, electron transfer number, and kinetic current density increase when the electrical conductivity of the material increases but decrease when the material has a poor porosity, which shows that the two factors should be finely tuned by the amount of nano‐CuS for ORR application. Of these materials, CuS(28 wt %)@Cu‐BTC exhibits the best activity, showing the onset potential of 0.91 V vs. RHE, quasi‐four‐electron transfer pathway, and a kinetic current density of 11.3 mA cm^?2 at 0.55 V vs. RHE.     

Combination of Optimization and Metalated‐Ligand Exchange: An Effective Approach to Functionalize UiO‐66(Zr) MOFs for CO2 Separation

The strategy to functionalize water‐stable metal–organic frameworks (MOFs) in order to improve their CO₂ uptake capacities for efficient CO₂ separation remains limited and challenging. We herein present an effective approach to functionalize a prominent water‐stable MOF, UiO‐66(Zr), by a combination of optimization and metalated‐ligand exchange. In particular, by systematic optimization, we have successfully obtained UiO‐66(Zr) of the highest BET surface area reported so far (1730 m² g^?1). Moreover, it shows a hybrid Type I/IV N₂ isotherm at 77 K and a mesopore size of 3.9 nm for the first time. The UiO‐66 MOF underwent a metalated‐ligand‐exchange (MLE) process to yield a series of new UiO‐66‐type MOFs, among which UiO‐66‐(COONa)₂‐EX and UiO‐66‐(COOLi)₄‐EX MOFs have both enhanced CO₂ working capacity and IAST CO₂/N₂ selectivity. Our approach has thus suggested an alternative design to achieve water‐stable MOFs with high crystallinity and gas uptake for efficient CO₂ separation.     

On‐surface Synthesis of a Semiconducting 2D Metal–Organic Framework Cu3(C6O6) Exhibiting Dispersive Electronic Bands

A 2D metal–organic framework (2D‐MOF) was formed on a Cu(111) substrate using benzenehexol molecules. By means of a combination of scanning tunneling microscopy and spectroscopy, X‐ray photoelectron spectroscopy and density‐functional theory, the structure of the 2D‐MOF is determined to be Cu₃(C₆O₆), which is stabilized by O–Cu–O bonding motifs. We find that upon adsorption on Cu(111), the 2D‐MOF features a semiconductor band structure with a direct band gap of 1.5 eV. The O–Cu–O bonds offer efficient charge delocalization, which gives rise to a highly dispersive conduction band with an effective mass of 0.45 m_e at the band bottom, implying a high electron mobility in this material.     

Controlled Synthesis of Porous Coordination‐Polymer Microcrystals with Definite Morphologies and Sizes under Mild Conditions

Herein, we report a facile and convenient method for the synthesis of the porous coordination polymer MOF‐14 [Cu₃(BTB)₂] (H₃BTB=4,4′,4′′‐benzene‐1,3,5‐triyl‐tribenzoic acid) as microcrystals with definite shapes and crystal facets controlled by the reaction medium at room temperature. The amount of sodium acetate added to the reaction system plays a crucial role in the shape evolution of MOF‐14 from rhombic dodecahedrons to truncated rhombic dodecahedrons and cubes with truncated edges and then to cubes. The addition of a base could accelerate the formation rate of crystal growth and increase the supersaturation of crystal growth, thus resulting in the formation of MOF‐14 cube crystals with high‐energy crystal facets. The morphological evolution was also observed for HKUST‐1 [Cu₃(BTC)₂] (H₃BTC=1,3,5‐benzenetricarbocylic acid) from octahedrons to cubes, thus verifying the probable mechanism of the morphological transformation. The gas‐adsorption properties of MOF‐14 with different shapes were studied and reveal that the porous coordination‐polymer microcrystals display excellent and morphology‐dependent sorption properties.     

Tandem magnetization and post‐synthetic metal ion exchange of metal–organic framework: Synthesis,characterization and catalytic study

For the first time, metal‐exchange in a magnetic metal–organic framework (MOF) via tandem magnetization and post‐synthetic modification has been developed. The new magnetic mixed‐metal metal–organic framework nanocomposite, CoFe₂O₄/[Cu_0.63/Zn_0.37‐TMU‐17‐NH₂] (CoFe₂O₄/[Cu/Zn‐MOF]) has been synthesized by immersing the CoFe₂O₄/Zn‐TMU‐17‐NH₂ (CoFe₂O₄/Zn‐MOF) as a template in DMF solution of Cu (II) salts. CoFe₂O₄/[Cu/Zn‐MOF] showed to be a highly reactive and easily recoverable magnetic catalyst for the preparation of tetrazole derivatives via one‐pot three‐component reactions of different aldehydes with hydroxyl amine hydrochloride and sodium azide. Our results (Fourier transform‐infrared, inductively coupled plasma‐optical emission spectroscopy, powder X‐ray diffraction, field emission‐scanning electron microscopy, energy‐dispersive X‐ray spectroscopy‐mapping and vibrating‐sample magnetometer) show successful partial metal‐exchange in which the framework integrity remained intact during the metal‐exchange process.     

Studies on Photocatalytic CO2 Reduction over NH2‐Uio‐66(Zr) and Its Derivatives: Towards a Better Understanding of Photocatalysis on Metal–Organic Frameworks

Metal–organic framework (MOF) NH₂‐Uio‐66(Zr) exhibits photocatalytic activity for CO₂ reduction in the presence of triethanolamine as sacrificial agent under visible‐light irradiation. Photoinduced electron transfer from the excited 2‐aminoterephthalate (ATA) to Zr oxo clusters in NH₂‐Uio‐66(Zr) was for the first time revealed by photoluminescence studies. Generation of Zr^III and its involvement in photocatalytic CO₂ reduction was confirmed by ESR analysis. Moreover, NH₂‐Uio‐66(Zr) with mixed ATA and 2,5‐diaminoterephthalate (DTA) ligands was prepared and shown to exhibit higher performance for photocatalytic CO₂ reduction due to its enhanced light adsorption and increased adsorption of CO₂. This study provides a better understanding of photocatalytic CO₂ reduction over MOF‐based photocatalysts and also demonstrates the great potential of using MOFs as highly stable, molecularly tunable, and recyclable photocatalysts in CO₂ reduction.     

MIL‐53(Al) as a Versatile Platform for Ionic‐Liquid/MOF Composites to Enhance CO2 Selectivity over CH4 and N2

Five different imidazolium‐based ionic liquids (ILs) were incorporated into a metal–organic framework (MOF), MIL‐53(Al), to investigate the effect of IL incorporation on the CO₂ separation performance of MIL‐53(Al). CO₂, CH₄, and N₂ adsorption isotherms of the IL/MIL‐53(Al) composites and pristine MIL‐53(Al) were measured to evaluate the effect of the ILs on the CO₂/CH₄ and CO₂/N₂ selectivities of the MOF. Of the composite materials that were tested, [BMIM][PF₆]/MIL‐53(Al) exhibited the largest increase in CO₂/CH₄ selectivity, 2.8‐times higher than that of pristine MIL‐53(Al), whilst [BMIM][MeSO₄]/MIL‐53(Al) exhibited the largest increase in CO₂/N₂ selectivity, 3.3‐times higher than that of pristine MIL‐53(Al). A comparison of the CO₂ separation potentials of the IL/MOF composites showed that the [BMIM][BF₄]‐ and [BMIM][PF₆]‐incorporated MIL‐53(Al) composites both showed enhanced CO₂/N₂ and CO₂/CH₄ selectivities at pressures of 1–5 bar compared to composites of CuBTC and ZIF‐8 with the same ILs. These results demonstrate that MIL‐53(Al) is a versatile platform for IL/MOF composites and could help to guide the rational design of new composites for target gas‐separation applications.     

A Novel Electrochemical Sensor Based on Copper‐based Metal‐Organic Framework for the Determination of Dopamine

A glassy carbon electrode (GCE) modified with a copper‐based metal‐organic framework (MOF) [HKUST‐1, HKUST‐1 = Cu₃(BTC)₂ (BTC = 1,3,5‐benzenetricarboxylicacid)] was developed as a highly sensitive and simple electrochemical sensor for the determination of dopamine (DA). The MOF was prepared by a hydrothermal process, and the morphology and crystal phase of the MOF were characterized by scanning electron microscopy (SEM) and X‐ray diffraction (XRD), respectively. Meanwhile, the electrochemical performance was investigated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS). Under optimized conditions, the modified electrode showed excellent electrocatalytic activity and high selectivity toward DA. The linear response range was from 5.0 × 10⁻⁷ to 1.0 × 10⁻⁴ M and the detection limit was as low as 1.5 × 10⁻⁷ M. Moreover, the electrochemical sensor was used to detect DA in real samples with excellent results. MOF‐based sensors hold great promise for routine sensing applications in the field of electrochemical sensing.     

POM‐Catalyzed In Situ Ligand Synthesis for the Construction of Metal Complexes and Their Use in the Formation of Coordination Polymers

Six organic–inorganic hybrid materials were synthesized by the in situ oxidation of neocuproine by using MoO₃/Na₂MoO₄ as the catalyst in the presence of Cu(NO₃)₂. The crystal structures of Mo8‐Cu4‐PHEN and Mo8‐Cu2‐5(2PIC) are composed of [Mo₈O₂₆]^4? polyoxometalate (POM) units, whereas the crystal structure of Mo6‐Cu‐COPHEN is composed of a [Mo₆O₁₉]^2? POM unit; both POM units could be considered as the active form of the catalyst. Reaction of the hybrid materials with 1,3,5‐benzenetricarboxylic acid (BTC) resulted in the formation of two different coordination polymers (CPs) under different reaction conditions. These CPs, depending on their structural attributes, exhibit distinct differences in the adsorption of H₂, CO₂, and water. The use of 2‐methylpyridine instead of neocuproine does not give any oxidation products under the same reaction conditions due to the incorrect positioning of the methyl group with respect to the Cu^II center.     

Locating Gases in Porous Materials: Cryogenic Loading of Fuel‐Related Gases Into a Sc‐based Metal–Organic Framework under Extreme Pressures

An alternative approach to loading metal organic frameworks with gas molecules at high (kbar) pressures is reported. The technique, which uses liquefied gases as pressure transmitting media within a diamond anvil cell along with a single‐crystal of a porous metal–organic framework, is demonstrated to have considerable advantages over other gas‐loading methods when investigating host–guest interactions. Specifically, loading the metal–organic framework Sc₂BDC₃ with liquefied CO₂ at 2 kbar reveals the presence of three adsorption sites, one previously unreported, and resolves previous inconsistencies between structural data and adsorption isotherms. A further study with supercritical CH₄ at 3–25 kbar demonstrates hyperfilling of the Sc₂BDC₃ and two high‐pressure displacive and reversible phase transitions are induced as the filled MOF adapts to reduce the volume of the system.     

Structural analysis of interpenetrated methyl‐modified MOF‐5 and its gas‐adsorption properties

The first example of an interpenetrated methyl‐modified MOF‐5 with the formula Zn₄O(DMBDC)₃(DMF)₂, where DMBDC^2? is 2,5‐dimethylbenzene‐1,4‐dicarboxylate and DMF is N,N‐dimethylformamide (henceforth denoted as Me₂MOF‐5‐int ), namely, poly[tris(μ₄‐2,5‐dimethylbenzene‐1,4‐dicarboxylato)bis(N,N‐dimethylformamide)‐μ₄‐oxido‐tetrazinc(II)], [Zn₄(C₁₀H₈O₄)₃O(C₃H₇NO)₂]_n, has been obtained from a solvothermal synthesis of 2,5‐dimethylbenzene‐1,4‐dicarboxylic acid and Zn(NO₃)₂·6H₂O in DMF. A systematic study revealed that the choice of solvent is of critical importance for the synthesis of phase‐pure Me₂MOF‐5‐int , which was thoroughly characterized by single‐crystal and powder X‐ray diffraction (PXRD), as well as by gas‐adsorption analyses. The Brunauer–Emmett–Teller surface area of Me₂MOF‐5‐int (660 m² g^?1), determined by N₂ adsorption, is much lower than that of nonpenetrated Me₂MOF‐5 (2420 m² g^?1). However, Me₂MOF‐5‐int displays an H₂ uptake capacity of 1.26 wt% at 77 K and 1.0 bar, which is comparable to that of non‐interpenetrated Me₂MOF‐5 (1.51 wt%).     

Hollow Metal–Organic‐Framework‐Mediated In Situ Architecture of Copper Dendrites for Enhanced CO2 Electroreduction

Electrocatalytic reduction of CO₂ to a single product at high current densities and efficiencies remains a challenge. However, the conventional electrode preparation methods, such as drop‐casting, usually suffer from low intrinsic activity. Herein, we report a synthesis strategy for preparing heterogeneous electrocatalyst composed of 3D hierarchical Cu dendrites that derived from an in situ electrosynthesized hollow copper metal–organic framework (MOF), for which the preparation of the Cu‐MOF film took only 5 min. The synthesis strategy preferentially exposes active sites, which favor's the reduction of CO₂ to formate. The current density could be as high as 102.1 mA cm^?2 with a selectivity of 98.2 % in ionic‐liquid‐based electrolyte and a commonly used H‐type cell.     

Enhanced CO2 Adsorption Affinity in a NbO‐type MOF Constructed from a Low‐Cost Diisophthalate Ligand with a Piperazine‐Ring Bridge

A metal–organic framework (NPC‐6) with an NbO topology based on a piperazine ring‐bridged diisophthalate ligand was synthesized and characterized. The incorporated piperazine group leads to an enhanced adsorption affinity for CO₂ in NPC‐6, in which the CO₂ uptake is 4.83 mmol g^?1 at 293 K and 1 bar, ranking among the top values of CO₂ uptake on MOF materials. At 0.15 bar and 293 K, the NPC‐6 adsorbs 1.07 mmol g^?1 of CO₂, which is about 55.1 % higher than that of the analogue MOF NOTT‐101 under the same conditions. The enhanced CO₂ uptake combined with comparable uptakes for CH₄ and N₂ leads to much higher selectivities for CO₂/CH₄ and CO₂/N₂ gas mixtures on NPC‐6 than on NOTT‐101. Furthermore, an N‐alkylation is used in the synthesis of the PDIA ligand, leading to a much lower cost compared with that in the synthesis of ligands in the NOTT series, as the former does not require a palladium‐based catalyst and borate esters. Thus, we conclude that NPC‐6 is a promising candidate for CO₂ capture applications.     

Post‐Synthetic Reversible Incorporation of Organic Linkers into Porous Metal–Organic Frameworks through Single‐Crystal‐to‐Single‐Crystal Transformations and Modification of Gas‐Sorption Properties

The porous metal–organic framework (MOF) {[Zn₂(TCPBDA)(H₂O)₂]?30 DMF?6 H₂O}_n ( SNU‐30 ; DMF=N,N‐dimethylformamide) has been prepared by the solvothermal reaction of N,N,N′,N′‐tetrakis(4‐carboxyphenyl)biphenyl‐4,4′‐diamine (H₄TCPBDA) and Zn(NO₃)₂?6 H₂O in DMF/tBuOH. The post‐synthetic modification of SNU‐30 by the insertion of 3,6‐di(4‐pyridyl)‐1,2,4,5‐tetrazine (bpta) affords single‐crystalline {[Zn₂(TCPBDA)(bpta)]?23 DMF?4 H₂O}_n ( SNU‐31 SC ), in which channels are divided by the bpta linkers. Interestingly, unlike its pristine form, the bridging bpta ligand in the MOF is bent due to steric constraints. SNU‐31 can be also prepared through a one‐pot solvothermal synthesis from Zn^II, TCPBDA^4?, and bpta. The bpta linker can be liberated from this MOF by immersion in N,N‐diethylformamide (DEF) to afford the single‐crystalline SNU‐30 SC , which is structurally similar to SNU‐30 . This phenomenon of reversible insertion and removal of the bridging ligand while preserving the single crystallinity is unprecedented in MOFs. Desolvated solid SNU‐30′ adsorbs N₂, O₂, H₂, CO₂, and CH₄ gases, whereas desolvated SNU‐31′ exhibits selective adsorption of CO₂ over N₂, O₂, H₂, and CH₄, thus demonstrating that the gas adsorption properties of MOF can be modified by post‐synthetic insertion/removal of a bridging ligand.     

Multiscale Computational Study on the Adsorption and Separation of CO2/CH4 and CO2/H2 on Li+‐Doped Mixed‐Ligand Metal–Organic Framework Zn2(NDC)2(diPyNI)

The quantum mechanics (QM) method and grand canonical Monte Carlo (GCMC) simulations are used to study the effect of lithium cation doping on the adsorption and separation of CO₂, CH₄, and H₂ on a twofold interwoven metal–organic framework (MOF), Zn₂(NDC)₂(diPyNI) (NDC=2,6‐naphthalenedicarboxylate; diPyNI=N,N′‐di‐(4‐pyridyl)‐1,4,5,8‐naphthalenetetracarboxydiimide). Second‐order Moller–Plesset (MP2) calculations on the (Li⁺–diPyNI) cluster model show that the energetically most favorable lithium binding site is above the pyridine ring side at a distance of 1.817 Å from the oxygen atom. The results reveal that the adsorption capacity of Zn₂(NDC)₂(diPyNI) for carbon dioxide is higher than those of hydrogen and methane at room temperature. Furthermore, GCMC simulations on the structures obtained from QM calculations predict that the Li⁺‐doped MOF has higher adsorption capacities than the nondoped MOF, especially at low pressures. In addition, the probability density distribution plots reveal that CO₂, CH₄, and H₂ molecules accumulate close to the Li cation site. The selectivity results indicate that CO₂/H₂ selectivity values in Zn₂(NDC)₂(diPyNI) are higher than those of CO₂/CH₄. The selectivity of CO₂ over CH₄ on Li⁺‐doped Zn₂(NDC)₂(diPyNI) is improved relative to the nondoped MOF.     

Sustainable Catalysis: Rational Pd Loading on MIL‐101Cr‐NH2 for More Efficient and Recyclable Suzuki–Miyaura Reactions

Palladium nanoparticles have been immobilized into an amino‐functionalized metal–organic framework (MOF), MIL‐101Cr‐NH₂, to form Pd@MIL‐101Cr‐NH₂. Four materials with different loadings of palladium have been prepared (denoted as 4‐, 8‐, 12‐, and 16 wt %Pd@MIL‐101Cr‐NH₂). The effects of catalyst loading and the size and distribution of the Pd nanoparticles on the catalytic performance have been studied. The catalysts were characterized by using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier‐transform infrared (FTIR) spectroscopy, powder X‐ray diffraction (PXRD), N₂‐sorption isotherms, elemental analysis, and thermogravimetric analysis (TGA). To better characterize the palladium nanoparticles and their distribution in MIL‐101Cr‐NH₂, electron tomography was employed to reconstruct the 3D volume of 8 wt %Pd@MIL‐101Cr‐NH₂ particles. The pair distribution functions (PDFs) of the samples were extracted from total scattering experiments using high‐energy X‐rays (60 keV). The catalytic activity of the four MOF materials with different loadings of palladium nanoparticles was studied in the Suzuki–Miyaura cross‐coupling reaction. The best catalytic performance was obtained with the MOF that contained 8 wt % palladium nanoparticles. The metallic palladium nanoparticles were homogeneously distributed, with an average size of 2.6 nm. Excellent yields were obtained for a wide scope of substrates under remarkably mild conditions (water, aerobic conditions, room temperature, catalyst loading as low as 0.15 mol %). The material can be recycled at least 10 times without alteration of its catalytic properties.     

Metal–Organic Framework/PVDF Composite Membranes with High H2 Permselectivity Synthesized by Ammoniation

Herein we report a new ammoniation‐based chemical modification strategy for synthesis of continuous and uniform metal–organic framework (MOF)/polyvinylidene fluoride (PVDF) membranes with attractive performance. Ammoniation can promote the support PVDF membrane to produce amino groups, form a nanoparticle structure, and be well cross‐linked; therefore, the high‐density heterogeneous nucleation sites for MOFs growth were provided and the thermal stability and chemical resistance of composite membranes can be greatly improved. The high‐quality layers of representative Cu‐BTC and ZIF‐8 were synthesized on the chemically modified PVDF membranes. By ammoniation, ZIF‐7 can even be grown under harsh synthetic conditions such as in DMF precursor solutions at 403 K. The fabricated MOF/PVDF composite membranes with excellent hollow fiber structures and enhanced structural stability exhibited high H₂ permselectivities for H₂/CO₂ and H₂/N₂.     

Zn3(BTC)2 as a Highly Efficient Reusable Catalyst for the Synthesis of 2‐Aryl‐1H‐Benzimidazole

Zn₃(BTC)₂ metal‐organic frameworks as recyclable and heterogeneous catalysts were effectively used to catalyze the synthesis of benzimidazole derivatives from o‐phenylendiamine and aldehydes in ethanol. This method provides 2‐aryl‐1H‐benzimidazoles in good to excellent yields with little catalyst loading. The catalyst was characterized using different techniques such as X‐ray diffraction (XRD), energy dispersive X‐ray (EDX) analysis, scanning electron microscopy (SEM), and Fourier transform infrared (FT‐IR) spectroscopy.