聚苯乙烯修饰碳纳米管表面的研究

利用原子转移自由基聚合方法合成了端基具有一个卤素的聚苯乙烯, 并通过叠氮化反应得到端基为叠氮基团的聚苯乙烯. 利用叠氮基与单壁或复壁碳纳米管的反应， 将聚苯乙烯接到碳纳米管的表面上, 实现了碳纳米管的化学修饰. 通过FTIR, XPS, TEM, UV和Raman光谱等技术证明了聚苯乙烯以共价键形式结合到碳纳米管表面上. 利用TGA估算出连接在碳纳米管上的聚苯乙烯的含量, 并推测出复壁碳纳米管中较多的结构缺陷更有利于聚合物的接枝.     

单壁碳纳米管内包合有机小分子(乙炔、乙烯和乙烷)结构的理论研究

采用量子化学密度泛函B3LYP方法计算并对比研究了内包合三种有机小分子(乙炔、乙烯和乙烷)的(5,5)型扶手椅式碳纳米管复合物的结构以及电子性质. 研究结果表明, 中心掺杂物放在碳纳米管的管轴上的异构体比掺杂物垂直于管轴的异构体稳定; 内嵌有机小分子碳纳米管复合物的形成过程为吸热过程; 有机小分子的插入会使其HOMO-LUMO能隙变大; 并引起碳纳米管直径的轻微加大, 以减少碳管张力, 其形变程度增大的顺序依次为C2H2相似文献   

单层碳纳米管的化学修饰

单层碳纳米管 (SWNT)是 Iijima博士 [1]于 1 993年首次发现的 .它具有非常独特的物理和化学性质 ,因而成为近年来研究的热点问题 .随着单层碳纳米管的合成技术和纯化研究的不断完善 [2～ 5] ,关于它的研究方向开始转向化学反应和应用研究 .由于单层碳纳米管不溶于水或有机溶剂而限制了对其化学性质的研究 .单层碳纳米管的端头是由碳的五元环和六元环组成的半球形 .氧化作用可将该端头打开并转化为羧基 ,从而与其它的化学试剂发生反应 .Liu Jie等 [6] 用浓硫酸和浓硝酸的混合物氧化单层碳纳米管 ,将之裁剪成 1 50～ 80 0 nm的“短管”.在…     

Dispersion and phase separation of carbon nanotubes in ultrathin polymer films

The inner structure and nanoscale distribution of the stiffness was studied for polymer-single-wall carbon nanotube composites. Dispersion of nanotubes in a polystyrene and polyurethane polymer matrix was achieved by a proper choice of the organic solvent (NMP) and sonification of polymer/SWNT solutions. Ultrathin nanocomposite films were prepared through a dip-coating procedure and possessed a noticeable degree of nanotube orientation in the direction of the applied shear force. Peculiarities of the phase separation in the films were studied by atomic force microscopy (with application of force modulation mode to map the nanotube distribution within the polymer matrix) and Raman spectroscopy.     

Catalytic polymerization and facile grafting of poly(furfuryl alcohol) to single-wall carbon nanotube: preparation of nanocomposite carbon

A nanocomposite carbon was prepared by grafting a carbonizable polymer, poly(furfuryl alcohol) (PFA), to a single-wall carbon nanotube (SWNT). The SWNT was first functionalized with arylsulfonic acid groups on the sidewall via a method using a diazonium reagent. Both Raman and FTIR spectroscopies were used to identify the functional groups on the nanotube surface. HRTEM imaging shows that the SWNT bundles are exfoliated after functionalization. Once this state of the SWNTs was accomplished, the PFA-functionalized SWNT (PFA-SWNT) was prepared by in situ polymerization of furfuryl alcohol (FA). The sulfonic acid groups on the surface of the SWNT acted as a catalyst for FA polymerization, and the resulting PFA then grafted to the SWNTs. The surfaces of the SWNTs converted from hydrophilic to hydrophobic when they were wrapped with PFA. The formation of the polymer and the attraction between it and the sulfonic acid groups were confirmed by IR spectra. A nanocomposite carbon was generated by heating the PFA-SWNT in argon at 600 degrees C, a process during which the PFA was transformed to nanoporous carbon (NPC) and the sulfonic acid groups were cleaved from the SWNT. Based upon the Raman spectra and HRTEM images of the composite, it is concluded that SWNTs survive this process and a continuous phase is formed between the NPC and the SWNT.     

The possible way to evaluate the purity of double-walled carbon nanotubes over single wall carbon nanotubes by chemical doping

Here, we carried out Raman study on chemically doped single wall carbon nanotube (SWNT)/double-walled carbon nanotube (DWNT) mixed bucky-papers. Their highly different Raman responses (e.g., a large upshift of tangential mode of SWNT and no large changes in the frequencies of tangential mode assigned to the outer tubes of the DWNT) upon doping with the sulfuric acid could be used as a qualitative indicator of the purity of the DWNT samples with the concentration of its SWNTs contents.     

Mechanisms of single-walled carbon nanotube probe-sample multistability in tapping mode AFM imaging

When using single-walled carbon nanotube (SWNT) probes to create AFM images of SWNT samples in tapping mode, elastic deformations of the probe and sample result in a decrease in the apparent width of the sample. Here we show that there are two major mechanisms for this effect, smooth gliding and snapping, and compare their dynamics to the case when a conventional silicon tip is used to image a bare silicon surface. Using atomistic and continuum simulations, we analyze in detail the shape of the tip-sample interaction potential for three model cases and show that in the absence of adhesion and friction forces, more than two discrete, physically meaningful solutions of the oscillation amplitude are possible when snapping occurs (in contrast to the existence of one attractive and one repulsive solution for conventional silicon AFM tips). We present experimental results indicating that a continuum of amplitude solutions is possible when using SWNT tips and explain this phenomenon with dynamic simulations that explicitly include tip-sample adhesion and friction forces. We also provide simulation results of SWNT tips imaging Si(111)-CH3 surface step edges and Au nanocrystals, which indicate that SWNT probe multistability may be a general phenomenon, not limited to SWNT samples.     

超支化聚对氯甲基苯乙烯修饰碳纳米管表面的研究

用原子转移自由基聚合(ATRP)与自缩合乙烯基聚合(SCVP)相结合合成超支化聚合物聚对氯甲基苯乙烯(PCMS),该聚合物每个分枝均以卤素原子封端. 用叠氮化反应将卤素原子转换为—N3. 通过—N3与单壁或复壁碳纳米管反应将超支化聚合物接到碳纳米管的表面上, 实现了碳纳米管的化学修饰. 通过FTIR, XPS, TEM和Raman光谱等证明PCMS是以共价键形式结合到碳纳米管表面上的. 利用TGA估算出碳纳米管表面的修饰密度, 证明用超支化结构大量的端基可反应的官能团可以改善聚合物对碳纳米管的修饰效果.     

Single-walled carbon nanotubes of controlled diameter and bundle size and their field emission properties

Field emission studies were conducted on as-produced CoMoCAT single-walled carbon nanotube/silica composites with controlled nanotube diameter and bundle size. It has been observed that the as-produced nanotube material does not need to be separated from the high-surface area catalyst to be an effective electron emitter. By adjusting the catalytic synthesis conditions, single-walled carbon nanotubes (SWNT) of different diameters and bundle sizes were synthesized. A detailed characterization involving Raman spectroscopy, optical absorption (vis-NIR), SEM, and TEM was conducted to identify the nanotube species present in the different samples. The synthesis reaction temperature was found to affect the nanotube diameter and bundle size in opposite ways; that is, as the synthesis temperature increased the nanotube average diameter became larger, but the bundle size became smaller. A gradual and consistent reduction in the emission onset field was observed as the synthesis temperature increased. It is suggested that the bundle size, more than the nanotube diameter or chirality, determines the field emission characteristics of these composites. This is a clear demonstration that field emission characteristics of SWNT can be controlled by the nanotube synthesis conditions.     

Single-walled carbon nanotube-based coaxial nanowires: synthesis, characterization, and electrical properties

We report herein the template-directed synthesis, characterization, and electric properties of single-walled carbon nanotube- (SWNT-) based coaxial nanowires, that is, core (SWNT)-shell (conducting polypyrrole and polyaniline) nanowires. The SWNTs were first dispersed in aqueous solutions containing cationic surfactant cetyltrimethylammonium bromide (CTAB) or nonionic surfactant poly(ethylene glycol) mono-p-nonyl phenyl ether (O pi-10). Each individual nanotube (or small bundle) was then encased in its own micellelike envelope with hydrophobic surfactant groups orientated toward the nanotube and hydrophilic groups orientated toward the solution. And thus a hydrophobic region within the micelle/SWNT (called a micelle/SWNT hybrid template) was formed. Insertion and growth of pyrrole or aniline monomers in this hybrid template, upon removal of the surfactant, produce coaxial structures with a SWNT center and conducting polypyrrole or polyaniline coating. Raman and Fourier transform infrared (FTIR) spectroscopy and scanning (SEM) and transmission (TEM) electron microscopy were used to characterize the composition and the structures of these coaxial nanowires. The results revealed that the micellar molecules used could affect the surface morphologies of the resulting coaxial nanowires but not the molecular structures of the corresponding conducting polymers. Electric properties testing indicated that the SWNTs played the key roles in the conducting polymer/SWNT composites during electron transfer in the temperature range 77 K to room temperature. Compared with the SWNT network embedded in the conducting polymers, the composites within which SWNTs were coated perfectly by the identical conducting polymers exhibited higher barrier heights during electron transfer.     

Cellulose Nanocrystal-Assisted Dispersion of Luminescent Single-Walled Carbon Nanotubes for Layer-by-Layer Assembled Hybrid Thin Films

Highly stable single-walled carbon nanotube (SWNT) dispersions are obtained after ultrasonication in cellulose nanocrystal (CN) aqueous colloidal suspensions. Mild dispersion conditions were applied to preserve the SWNT length in order to facilitate the identification of hybrid objects. This led to a moderate dispersion of 24% of the SWNTs. Under these conditions, atomic force microscopy (AFM) and transmission electron microscopy (TEM) experiments succeeded in demonstrating the formation of hybrid particles in which CNs are aligned along the nanotube axis by a self-assembly process. These SWNT/CN dispersions are used to create multilayered thin films with the layer-by-layer method using polyallylamine hydrochloride as a polyelectrolyte. Homogeneous films from one to eight bilayers are obtained with an average bilayer thickness of 17 nm. The presence of SWNTs in each bilayer is attested to by characteristic Raman signals. It should be noted that these films exhibit a near-infrared luminescence signal due to isolated and well-separated nanotubes. Furthermore, scanning electron microscopy (SEM) suggests that the SWNT network is percolating through the film.     

Spectroscopic characterization of P3HT/SWNT composites synthesized using in situ GRIM methods: Improved polymer ordering via nanoscaffolding

Poly(3‐hexylthiophene)/single‐walled carbon nanotube (P3HT/SWNT) materials are synthesized using an in‐situ Grignard metathesis approach. The structural properties and photophysics of the materials are studied using a multitude of techniques, including ¹H NMR, FTIR, UV–vis absorption, Raman, photoluminescence (PL), and transient absorption spectroscopies. P3HT/SWNT composites with high P3HT regioregularity (rr > 96%) are observed. Raman spectroscopic data on the solid samples reveals an increase in the dispersion rate parameter with increasing SWNT concentration, thereby indicating close overlap and strong interactions between P3HT and the carbon nanotubes. Changes in the solution‐phase PL quantum yields and excited‐state lifetimes relative to pure P3HT support these conclusions, and indicate that strong interactions persist even after the composites are dispersed in organic solvents. The high regioregularity and enhanced P3HT–SWNT interactions are promising attributes for improving the morphology and efficiency of functional P3HT/SWNT materials. © 2013 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 310–320     

Unambiguous Diagnosis of Photoinduced Charge Carrier Signatures in a Stoichiometrically Controlled Semiconducting Polymer‐Wrapped Carbon Nanotube Assembly

Single‐walled carbon nanotube (SWNT)‐based nanohybrid compositions based on (6,5) chirality‐enriched SWNTs ([(6,5) SWNTs]) and a chiral n‐type polymer (S‐PBN(b)‐Ph₄PDI) that exploits a perylenediimide (PDI)‐containing repeat unit are reported; S‐PBN(b)‐Ph₄PDI‐[(6,5) SWNT] superstructures feature a PDI electron acceptor unit positioned at 3 nm intervals along the nanotube surface, thus controlling rigorously SWNT–electron acceptor stoichiometry and organization. Potentiometric studies and redox‐titration experiments determine driving forces for photoinduced charge separation (CS) and thermal charge recombination (CR) reactions, as well as spectroscopic signatures of SWNT hole polaron and PDI radical anion (PDI^?.) states. Time‐resolved pump–probe spectroscopic studies demonstrate that S‐PBN(b)‐Ph₄PDI‐[(6,5) SWNT] electronic excitation generates PDI^?. via a photoinduced CS reaction (τ_CS≈0.4 ps, Φ_CS≈0.97). These experiments highlight the concomitant rise and decay of transient absorption spectroscopic signatures characteristic of the SWNT hole polaron and PDI^?. states. Multiwavelength global analysis of these data provide two charge‐recombination time constants (τ_CR≈31.8 and 250 ps) that likely reflect CR dynamics involving both an intimately associated SWNT hole polaron and PDI^?. charge‐separated state, and a related charge‐separated state involving PDI^?. and a hole polaron site produced via hole migration along the SWNT backbone that occurs over this timescale.     

Single-walled carbon nanotube purification, pelletization, and surfactant-assisted dispersion: a combined TEM and resonant micro-raman spectroscopy study

Resonant Raman spectroscopy and transmission electron microscopy were used to characterize the structural changes of three single-walled carbon nanotube samples processed with purification, pelletization, and surfactant-assisted dispersion. A two-stage purification process selectively removes metallic tubes as well as small-diameter ones, enriching large-diameter semiconducting tubes. Pelletizing reduces the intertube distance but greatly increases the intensity ratio of the D band to the G band. Single-walled nanotube (SWNT) bundle size decreases during ultrasonication dispersion aided by a surfactant. SWNT bundles composed of large-diameter tubes are prone to debundling.     

Layer-by-layer electrostatic self-assembly of single-wall carbon nanotube polyelectrolytes

We have used anionic and cationic single-wall carbon nanotube polyelectrolytes (SWNT-PEs), prepared by the noncovalent adsorption of ionic naphthalene or pyrene derivatives on nanotube sidewalls, for the layer-by-layer self-assembly to prepare multilayers from carbon nanotubes with polycations, such as poly(diallyldimethylammonium) or poly(allylamine hydrochloride) (PDADMA or PAH, respectively), and polyanions (poly(styrenesulfonate), PSS). This is a general and powerful technique for the fabrication of thin carbon nanotube films of arbitrary composition and architecture and allows also an easy preparation of all-SWNT (SWNT/SWNT) multilayers. The multilayers were characterized with vis-near-IR spectroscopy, X-ray photoelectron spectroscopy (XPS), surface plasmon resonance (SPR) measurements, atomic force microscopy (AFM), and imaging ellipsometry. The charge compensation in multilayers is mainly intrinsic, which shows the electrostatic nature of the self-assembly process. The multilayer growth is linear after the initial layers, and in SWNT/polyelectrolyte films it can be greatly accelerated by increasing the ionic strength in the SWNT solution. However, SWNT/SWNT multilayers are much more inert to the effect of added electrolyte. In SWNT/SWNT multilayers, the adsorption results in the deposition of 1-3 theoretical nanotube monolayers per adsorbed layer, whereas the nominal SWNT layer thickness is 2-3 times higher in SWNT/polyelectrolyte films prepared with added electrolyte. AFM images show that the multilayers contain a random network of nanotube bundles lying on the surface. Flexible polyelectrolytes (e.g., PDADMA, PSS) probably surround the nanotubes and bind them together. On macroscopic scale, the surface roughness of the multilayers depends on the components and increases with the film thickness.     

Structural characterization of single-walled carbon nanotube bundles by experiment and molecular simulation

A procedure, combining molecular simulation, Raman spectroscopy, and standard nitrogen adsorption, is developed for structural characterization of single-walled carbon nanotube (SWNT) samples. Grand canonical Monte Carlo simulations of nitrogen adsorption are performed on the external and internal adsorption sites of homogeneous arrays of SWNTs of diameters previously determined by Raman spectroscopy of the sample. The results show the importance of the peripheral grooves of a nanotube bundle at low relative pressure and the insensitivity of nanotube diameter toward adsorption on the external surface of the bundle at higher pressures. Simulations also reveal that samples containing thin nanotubes have less internal adsorption capacity that saturates at lower pressure than those comprising large diameter nanotubes. The fraction of open-ended nanotubes in a sample can be estimated by scaling the simulated internal adsorption inside nanotubes to obtain a near perfect fit between simulated and experimental isotherms. This procedure allows extrapolation of adsorption properties to conditions in which all nanotubes in the sample are open-ended.     

Substrate-induced Raman frequency variation for single-walled carbon nanotubes

We report on the monotonic Raman frequency shift and intensity variation when a laser spot moves along the same single-walled carbon nanotube (SWNT) for both the radial-breathing mode (RBM) and the G-band. Our substrates are Si wafers coated with thermal oxide, and trenches with widths of 1-80 mum are etched in the SiO2 by photolithography and reactive ion etching. SWNTs are grown by chemical vapor deposition and lie on top of the SiO2 and across the trenches. When the laser spot moves from the middle of the trench to the SiO2 region along the nanotube, we observe a clear upshift in the RBM and G-band frequencies and a decrease of intensity. The effect is more significant with large ( approximately 2 nm) diameter nanotubes and appears to be chirality dependent. These studies provide important information about environmental effects on single-walled carbon nanotube resonant Raman spectroscopy.     

Interaction of SiO2 with single-walled carbon nanotubes

The effects of coating of a single-walled carbon nanotube (SWNT) with a nonbonded layer of silica are investigated via model system employing fully coordinated silica clusters. The geometric and electronic structures of the SWNT@SiO(2) composite system are calculated using periodic density functional (DF) calculations for a range of confining silica coatings. We show that silica can provide a protective bound coating to a single walled nanotube, which, importantly, only weakly perturbs the underlying properties of both components. Detailed analysis of the charge redistribution and changes in electronic structure upon coating the SWNT are performed to support this conclusion. Furthermore, as allowed by our versatile model system, the energetics of rotating a silica "bearing" around a nanotube "spindle" is also calculated to indicate the possibilities for SWNT@SiO(2)-based nanomechanical devices.     

Dispersion of single‐walled carbon nanotubes using nucleobase‐containing poly(acrylamide) polymers

Single‐walled carbon nanotubes (SWNTs) possess extraordinary properties, but suffer from poor solubility and a lack of purity. Of the possible routes available to solubilize and purify nanotube samples, the use of noncovalent functionalization is ideal as carbon nanotube properties are not deleteriously affected. A multitude of different dispersants have been investigated thus far, but of particular interest is deoxyribonucleic acid (DNA), which has previously been demonstrated to effectively separate metallic and semiconducting carbon nanotubes. Here, we investigate the ability of synthetic nucleobase‐containing poly(acrylamide) polymers to produce stable nanotube dispersions in organic solvents. Polymers bearing different nucleobase and backbone structures, as well as block copolymers with different block sequences were investigated. Polymer:SWNT mass ratios and solvent compositions were optimized for the nucleobase‐functionalized polymers, and semiconducting and metallic SWNT populations were identified by a combination of UV‐Vis‐NIR absorption, Raman, and fluorescence spectroscopy. These results demonstrate the capacity for synthetic DNA analogues to disperse SWNTs in organic media. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2611–2617