Electrochemical formation and reduction of silver oxides in alkaline media

The anodic oxidation of silver electrodes in NaOH solution and the reduction of the silver oxides formed were studied by potential step chronoamperometry. Oxidation of Ag to Ag₂O is a diffusion-controlled reaction, the diffusion control being established in the solid phase. Oxidation of Ag₂O to AgO proceeds via a nucleation and growth-controlled process. The amount of AgO decreased with increasing step height. The current—time curves for this reaction have been analysed with the Kolmogoroff—Avrami equation. Reduction of AgO to Ag₂O occurs initially on the outside of the electrode, and the rate of the reaction is limited by diffusion of ions across the thickening layer of Ag₂O. Reduction of Ag₂O to Ag proceeds via a nucleation and growth reaction.     

Traitement électrochimique d' eaux usées chargées de phénol : étude comparative sur des électrodes de dioxyde de plomb et de platine

Electrochemical treatment of waste water containing phenol: a comparative study on lead dioxide and platinum electrodes. The objective of this work was to study the efficiency of the Pb/PbO₂ electrode for decomposing the molecule of phenol, then to compare it to a platinum model electrode. Preliminary investigations by cyclic voltammetry showed that the Pb/PbO₂ anode presents a good chemical and electrochemical stability and possesses a high oxygen overvoltage. The study also showed that the electrochemical oxidation of phenol on Pt and PbO₂ in acidic media is a complex process. Long-time electrolysis was carried out using a three potential-plateau program with different values of the oxidation potentials and different concentrations of phenol. The obtained results showed that the transformation of phenol is total on the Pb/PbO₂ anode and that it is partial on Pt. On the other hand an increase in the phenol concentration decreases the rate of its conversion on the electrodes.     

The Unique Gas‐Phase Chemistry of the [AuO]+/CH4 Couple: Selective Oxygen‐Atom Transfer to,Rather than Hydrogen‐Atom Abstraction from,Methane

The thermal reaction of [AuO]⁺ with methane has been explored using FT‐ICR mass spectrometry complemented by high‐level quantum chemical calculations. In contrast to the previously studied congener [CuO]⁺, and to [AgO]⁺, [AuO]⁺ reacts with CH₄ exclusively via oxygen‐atom transfer to form CH₃OH, and a novel mechanistic scenario for this selective oxidation process has been revealed. Also, the origin of the inertness of the [AgO]⁺/CH₄ couple has been addressed computationally.     

Pseudo-potentiostatic electrolysis by potential buffering induced by the oxygen evolution reaction

A new approach is proposed in order to perform electrochemical oxidation of organics by working under galvanostatic conditions with the potential ‘buffered’ by the competing side reaction of oxygen evolution (OER). According to this process the working potential is fixed by the nature of electrode material and is buffered during organics oxidation by the side reaction of OER. This principle has been used for the selective oxidation of some model organic compounds on Ti/IrO₂ anode.     

Vertically Aligned CuO Nanowires Based Electrode for Amperometric Detection of Hydrogen Peroxide

Vertically aligned copper oxide (CuO) nanowires were synthesized by directly heating copper foil on a hotplate under ambient conditions. The as‐grown CuO nanowires film is mechanically stable and was facilely attached to a glassy carbon (GC) electrode, offering an excellent electrochemical sensing platform. The CuO nanowires electrode shows excellent electrocatalytic response to H₂O₂ with significantly lower overpotentials for its oxidation and reduction and also exhibits a fast response and high sensitivity for the amperometric detection of H₂O₂. The novel vertically aligned CuO nanowires electrode is readily applicable to other analytes and has great potential applications in the electrochemical detection.     

Synthesis and properties of tetragonal silver(I,III) oxide,AgO

The pure tetragonal AgO modification was obtained by ozonation of a suspension of Ag₂O or Ag in stirred water. The oxidation proceeds in two steps from Ag, with the intermediary formation of Ag₂O. An oxygen content corresponding to the formula AgO_1.15 is obtained when the bubbling of ozone is maintained for a long time. The thermal decomposition of tetragonal AgO is complex and has been studied by thermogravimetry and differential thermal analysis.     

Hydroxyl radicals electrochemically generated in situ on a boron-doped diamond electrode

The hydroxyl radicals electrochemically generated in situ on a boron-doped diamond (BDD) electrode have been investigated for the first time in different electrolyte media, over the whole pH range between 1 and 11. A more extensive characterisation of BDD electrochemical properties is very important to understand the reactivity of organic compounds towards electrochemical oxidation on the BDD electrode, which is related to their interaction with adsorbed hydroxyl radicals due to water oxidation on the electrode surface. An oxidation peak corresponding to the transfer of one electron and one proton was observed in pH <9 electrolytes, associated with the water discharge process and electrochemical generation of hydroxyl radicals, which can interact and enhance the electro-oxidation of organic compounds. In pH >9 electrolytes the electrochemical generation of hydroxyl radicals was not observed; ammonia buffer electrolyte gave a pH-independent peak corresponding to the ammonia oxidation reaction. Additionally, for most pH values studied, a few small peaks associated with the electrochemical interaction between non-diamond carbon species on the doped diamond electrode surface and the electrolyte were also seen, which suggests that the doped diamond is relatively unreactive, but not completely inert, and the electrogenerated hydroxyl radicals play a role as mediator in the oxidation of organics.     

Electrochemical study of intercalated vanadyl phosphate

A detailed electrochemical study of Li intercalation/deintercalation in VOPO₄ compounds with various inserted molecules (H₂O, HCOOH and CH₃COOH) is presented. For VOPO₄·2H₂O, water oxidation is responsible for capacity fading. In order to improve the cyclability, the electrochemical behavior of other intercalated VOPO₄ compounds, such as VOPO₄·H₂O, VOPO₄·HCOOH and VOPO₄·0.78CH₃COOH, has been studied. For all these materials, the intercalation (deintercalation) takes place in several steps. The electrochemical study of the monohydrate indicates that the vanadium-coordinated water molecule is more stable than the second water molecule towards cycling. The highest initial specific capacity values (approximately 100 mAh/g) are obtained for the compounds with the largest interlayer space. Upon cycling, the pillaring molecules are destroyed by a high-potential oxidation process, yielding a collapse of the 2D structure and thus a loss of crystallinity. As a result, the observed specific capacity is the same for all the materials after a long cycling. This capacity is higher than the anhydrous one.     

Fabrication of Hierarchically Structured MOF‐Co3O4 on Well‐aligned CuO Nanowire with an Enhanced Electrocatalytic Property

Engineering appropriate shape and size of three‐dimensional inorganic nanostructures materials is of one the main critical problems in pursuing high‐performance electrode materials. Herein, we fabricate a metal‐organic framework derived cobalt oxide (Co₃O₄) are grown on copper oxide nanowire (CuO NWs) supported on the surface of 3D copper foam substrate. The highly aligned CuO NWs were prepared by using electrochemical anodization of copper foam in ambient temperature and followed by MOF Co₃O₄ was grown via a simple in situ solution deposition then consequent calcination process. The obtained binder‐free 3D CuO NWs@Co₃O₄ nanostructures were further characterized by using X‐ray diffraction, X‐ray photoelectron spectroscopy, field‐emission scanning electron microscopy, and transmission electron microscopy. Furthermore, electrochemical sensing of glucose was studied by using Cyclic Voltammetry, and chronoamperometry techniques. Interestingly, 3D CuO NWs@Co₃O₄ electrode exhibits excellent performance for the oxidation of glucose compared with individual entities. The proposed sensor shows wide linear ranges from 0.5 μM to 0.1 mM with the sensitivity of 6082 μA/μM and the lowest detection limit (LOD) of 0.23 μM was observed with the signal to noise ratio, (S/N) of 3. The superior catalytic oxidation of glucose mainly is endorsed by the excellent electrical conductivity and synergistic effect of the Co₃O₄ and CuO NWs.     

Non-enzymatic electrochemical CuO nanoflowers sensor for hydrogen peroxide detection

The electrocatalytic activity of a CuO flower-like nanostructured electrode was investigated in terms of its application to enzyme-less amperometric H₂O₂ sensors. The CuO nanoflowers film was directly formed by chemical oxidation of copper foil under hydrothermal condition and then used as active electrode material of non-enzymatic electrochemical sensors for H₂O₂ detection under alkaline conditions. The sensitivity of the sensor with CuO nanoflowers electrode was 88.4 μA/mM cm² with a linear response in the range from 4.25 × 10⁻⁵ to 4 × 10⁻² M and a detection limit of 0.167 μM (S/N = 3). Excellent electrocatalytic activity, large surface-to-volume ratio and efficient electron transport property of CuO nanoflowers electrode have enabled stable and highly sensitive performance for the non-enzymatic H₂O₂ sensor.     

Tuning Interfacial Cu‐O Atomic Structures for Enhanced Catalytic Applications

Cu₂O/CuO_x (x=0, 1) nanocomposites with well‐defined morphologies have been widely applied in catalytic reactions. However, people still understand less about tuning interfacial Cu‐O atomic structures for enhanced catalytic applications, and a special review on this topic has not been reported so far. Herein, we summarize our understanding on tuning interfacial Cu‐O atomic structures based on the literature, including the formation as well as evolution mechanism of Cu‐O interfaces in Cu₂O/CuO and Cu₂O/Cu systems, and the improved performances in the fields of CO oxidation, NO_x oxidation, photoelectrocatalysis, water gas shift reaction, photodegradation of organic dyes, hydrogen evolution, and photoreduction of CO₂. Finally, we briefly propose several potential research directions.     

Cu2O/CuO Electrocatalyst for Electrochemical Reduction of Carbon Dioxide to Methanol

Herein, we report the controlled and direct fabrication of Cu₂O/CuO thin film on the conductive nickel foam using electrodeposition route for the electrochemical reduction of carbon dioxide (CO₂) to methanol. The electrocatalytic reduction was performed in CO₂ saturated aqueous solution consisting of KHCO₃, pyridine and HCl at room temperature. CO₂ reduction was carried out at a constant potential of −1.3 V for 120 min to study the electrochemical performance of the prepared electrocatalysts. Cu₂O/CuO shows better electrocatalytic activity with highest current density of 46 mA/cm². The prepared catalyst can be an efficient and selective electrode for the production of methanol.     

Electrochemical oxidation of chlorinated benzenes

The electrochemical oxidation of benzene and its chloro derivatives (n=1–3) has been studied in acetonitrile, water, and an aqueous emulsion at both metallic electrodes and dimensionally stable anodes. In acetonitrile all substrates underwent a six-electron oxidation near +3 V versus the standard hydrogen electrode. Low yields of organic products, principally phenols, were obtained; electrochemical combustion to CO₂ was a major reaction pathway, but current efficiencies were low.     

Thermal oxidative degradation of isotactic polypropylene catalyzed by copper and copper oxide interfaces

The oxidative degradation of isotactic polypropylene films coated on well-defined Cu(Cu₂O), CuO_0.67, and CuO films in a temperature range of 90–120°C in a quartz-spoon-gauge-reaction vessel was studied. This catalytic reaction has been compared with the oxidation of polypropylene without copper or oxide films. The reaction vessel contained, if needed, P₂O₅ and/or KOH as “getters” for H₂O and CO₂, these substances could be menitored continuously. Cu(Cu₂O) films were transformed during oxidation of the polymer to yellow CuO_0.67 below 100°C and above this temperature to black CuO in the presence of H₂O and CO₂, whereas in the absence of these compounds CuO was formed below 100°C and CuO_0.67 at 120°C. Characteristic autoxidation curves obtained in the absence of H₂O and CO₂ showed induction periods that were shorter for copper oxide-polymer interfaces than for glass-polymer interfaces (i.e., for uncatalyzed oxidation). Abnormalities were observed for Cu(Cu₂O)-polymer interfaces because of further oxidation of Cu during the reaction. The rates of oxygen consumption were faster for CuO_0.67-polymer and CuO-polymer than for the uncatalyzed reaction; the catalytic action of CuO_0.67 was somewhat larger than that of CuO. The important observation was made that the mechanism of oxidation is not the same in the absence and presence of reaction products; that is, H₂O and CO₂. This was confirmed by ion beam scattering experiments, which also revealed that an oxidation-reduction process takes place at Cu and their oxide interfaces. A mechanism for the catalytic oxidation process, based on the ease by which copper ions are released from the metal oxides at the interface, was formulated. These ions diffuse subsequently as actions of carboxylate anions into the bulk of the polymer. Arrhenius equations of oxygen consumption are given for all cases; the energy of activation calculated for the initiation of the uncatalyzed oxidation agrees with its literature value. The energy of activation for the initiation of the catalyzed reaction was a few kilocalories lower than that for the uncatalyzed reaction. Catalytic action is mainly operative for the initiation reaction at the interface and for the decomposition of hydroperoxides by copper ions. Preventing the delivery of copper ions to the polymer would be the most efficient way of inhibiting the catalysis.     

The Influence of Water Vapor on the Electrochemical Shift of an Ionic Liquid Measured by Ambient Pressure X-ray Photoelectron Spectroscopy

Ionic liquids (ILs) are considered to be one of the steppingstones to fabricate next generation electrochemical devices given their unique physical and chemical properties. The addition of water to ILs significantly impact electrochemical related properties including viscosity, density, conductivity, and electrochemical window. Herein we utilize ambient pressure X-ray photoelectron spectroscopy (APXPS) to examine the impact of water on values of the electrochemical shift (S), which is determined by measuring changes in binding energy shifts as a function of an external bias. APXPS spectra of C 1s, O 1s and N 1s regions are examined for the IL 1-butyl-3-methylimidazolium acetate, [C₄mim][OAc], at the IL/gas interface as a function of both water vapor pressure and external bias. Results reveal that in the absence of water vapor there is an IL ohmic drop between the working electrode and quasi reference electrode, giving rise to chemical specific S values of less than one. Upon introducing water vapor, S values approach one as a function of increasing water vapor pressure, indicating a decrease in the IL ohmic drop as the IL/water mixture becomes more conductive and the potential drop is driven by the electric double layer at the electrode/IL interface.     

Cyclic voltammetry of copper in sodium hydroxide solutions

The cyclic voltammograms of the Cu electrode were, obtained in NaOH solution as a function of the voltage scanning rate, electrolyte concentration and voltage range. A correlation was made between three well-defined anodic peaks and their corresponding cathodic ones. The anodic peaks were found to correspond successively to the formation of a monolayer of Cu₂O, formation of a thick multilayer film of CuO and finally Cu₂O₃ upon which O₂ is evolved. It is suggested that CuO is formed from the oxidation of Cu₂O and/or direct oxidation of metallic copper.Below 0.1 M NaOH the ratio of anodic to cathodic charges was found to be about unity, indicating the quantitative reduction of solid oxidation products, while at higher alkali concentrations higher charge ratios were obtained due to increasing proportions of soluble reaction products.The behaviour of the copper electrode in NaOH was found to be quite complicated. Thus, no simple relations were found between the voltage scanning rate and both the peak current and peak potential or between the peak current and the alkali, concentration. Further work is needed to obtain a definitive explanation of this behaviour.     

Anodic silver (II) oxides investigated by combined electrochemistry,ex situ XPS and in situ X‐ray absorption spectroscopy

Silver (II) oxide layers (AgO) were prepared by anodic oxidation of pre‐oxidized, Ag₂O‐covered silver electrodes in 1 M NaOH (pH 13.8). The oxidized electrodes were investigated using a combination of electrochemical techniques, ex situ X‐ray photoelectron spectroscopy (XPS) and in situ surface‐sensitive grazing incidence X‐ray absorption spectroscopy (EXAFS) under full potential control. The application of these different techniques leads to a detailed, consistent picture of the anodic silver (II) oxide layer formation. The experiments have shown that the chemical composition of the AgO layer varies significantly with oxidation potential, revealing a decreasing oxygen deficiency with increasing anodization potential and oxidation time. XPS as well as EXAFS experiments support the interpretation of the oxide as a mixed valence Ag ⁺ Ag^{3 +} O₂ with different contributions of Ag ⁺ and Ag^{3 +} species, depending on potential and anodization time. Copyright © 2009 John Wiley & Sons, Ltd.     

Room temperature electrochemical synthesis of CuO flower-like microspheres and their electrooxidative activity towards hydrogen peroxide

We describe a facile electrochemical route for the synthesis of CuO flower-like microspheres (CuO FMs) by anodic dissolution of bulk Cu in sodium hydroxide solution at room temperature and without heating. Scanning electron microscopy and X-ray diffraction revealed that the CuO FMs are phase-pure monoclinic crystallites and comprised of CuO nanoflakes. The concentration of NaOH has a large effect on the size of the CuO FMs. The possible formation mechanism is discussed. The CuO FMs are electrocatalytically active towards the oxidation of H₂O₂, and this has resulted in a sensor for H₂O₂. To our knowledge, this is the simplest way to obtain clean CuO FMs.

Al Electrode Modified by Au Atoms as a Novel Electrode for Electrocatalytic Oxidation of Thiosulfate

An aluminum electrode modified with gold atoms was introduced as a novel electrode. Gold atoms were deposited both chemically and electrochemically onto the aluminum electrode to make an aluminum/gold (Al/Au) modified electrode (ME). The experimental results showed that the Al/Au modified electrode prepared by chemical deposition, exhibits much more current than the electrochemical deposition method. The electrochemical behavior of the Al/Au modified electrode was studied by cyclic voltammometry. This modified electrode showed two pairs of peaks, a₁c₁ and a₂c₂, with surface‐confined characteristics in a 0.5 M phosphate buffer. The dependence of E_pa of the second peak (a₂c₂) on pH shows a Nernestian behavior with a slope of 55 mV per unit pH. The effect of different supporting electrolytes, solution's pH and different scan rates on electrochemical behavior of Al/Au modified electrode was studied. Au deposited electrochemically on a Pt electrode (Pt/Au) was also used as another modified electrode. A comparative study of electrochemical behavior of bare Al, Pt/Au and Al/Au modified electrodes showed that both Pt/Au and Al/Au electrodes have the ability of electrocatalytic oxidation of S₂O₃^2?, but the electrocatalytic oxidation on the latter was better than the former. The kinetics of the catalytic reaction was investigated by using cyclic voltammetry and chronoamperometry techniques. The average value of the rate constant for the catalytic reaction and the diffusion coefficient were evaluated by means of chronoamperometry technique.     

Electrochemical Behavior of Some Thiotriazoles in Aqueous‐Alcoholic Media at GCE

An electrochemical study related to the electrooxidation of 4‐amino‐3‐thio‐5‐methyl‐1,2,4‐triazole (I), 4‐amino‐3‐thio‐5‐phenyl‐1,2,4‐triazole (II) and 3‐thio‐5‐phenyl‐1,2,4‐triazole (III), in 10% v/v methanol‐acetate buffer pH 4.6 has been performed. A variety of electrochemical techniques such as differential pulse voltammetry, cyclic voltammetry, double‐potential step chronoamperometry, rotating‐disk electrode voltammetry and coulometry, were employed to clarify that the mechanism of the electrode process follows the oxidation of thiol compounds. All the compounds exhibit similar redox behavior under the given conditions. They display one irreversible oxidation peak, which is diffusion controlled. From the plot of current function in cyclic voltammetry and the ratio of i_c/i_a less than one in double‐potential step chronoamperometry, it was established that these compounds undergo an one electron oxidation followed by a dimerization process involving the formation of disulfide derivative (EC mechanism). The pK_a values were obtained by the dependence of limiting current and potential with in the wide pH interval. The transfer coefficients, the diffusion coefficients and rate constant of coupled chemical reaction were also reported. The substituent effects were also investigated.