Use of holography in particle image velocimetry measurements of a swirling flow

 Particle Image Velocimetry (PIV) is now a well established experimental technique to measure two components of the velocity in a planar region of a flow field. This paper shows how its proven capabilities can be further extended by using holographic recording to register the particle displacements. Among other unique characteristics, holography enables the acquisition of multiple images on a single plate, and the recording of three dimensional images. These features are used to circumvent some of the limitations of conventional PIV. Some of these possibilities are demonstrated in this study by applying the technique to a high Reynolds number swirling flow using a lens-less off-axis orthogonal recording geometry. Received: 25 February 1998/ Accepted: 2 September 1998     

Local field correction PIV: on the increase of accuracy of digital PIV systems

Cross-correlation Particle Image Velocimetry (PIV) has become a well known and widely used experimental technique. It has been already documented that difficulties arise resolving velocity structures smaller than the interrogation window. This is caused by signal averaging over this window. A new cross-correlation PIV method that eliminates this restriction is presented. The new method brings some other enhancements, such as the ability to deal with large velocity gradients, seeding density inhomogeneities, and high dispersion in the brightness of the particles. The final result is a method with a remarkable capability for accurately resolving small scale structures in the flow, down to a few times the mean distance between particles. When compared to particle tracking velocimetry, the new method is capable of obtaining measurements at high seeding density concentrations. Therefore, better overall performance is obtained, especially with the limited resolutions of video CCDs. In this paper, the new method is described and its performance is evaluated and compared to traditional PIV systems using synthetic images. Application to real PIV data are included and the results discussed. Received: 9 March 1998 / Accepted: 25 August 1998     

Stereoscopic and tomographic PIV of a pitching plate

This paper applies particle image velocimetry (PIV) to a simplified, canonical, pitch-hold-return problem of a pitching plate in order to gain some understanding of how three dimensionality develops in such flows. Data from a progression of PIV studies, from stereoscopic PIV yielding three-component, two-dimensional (3C-2D) data to tomographic PIV yielding three-component, three-dimensional (3C-3D) data are presented thus providing progressively more detailed information. A comparison of results is made between the two techniques. The PIV study is performed in a water tunnel facility with cross-sectional area 500 × 500 mm, and involves a full-span (nominally two-dimensional) plate, suspended between a wall end boundary condition and a free surface, pitching at a dimensionless pitch rate of K _c  = 0.93 in flow at Re = 7,500. Results demonstrate the existence of spanwise flows in both the leading edge and trailing edge vortices, but with strong directionality in the leading edge vortex towards the wall end boundary condition. Observations of instantaneous flow patterns suggest also the existence of three-dimensional coherent vortex filament structures in the outer regions of the leading edge vortex.     

Stereoscopic PIV: validation and application to an isotropic turbulent flow

 A new stereoscopic PIV system to measure the three velocity components is developed and applied to grid turbulence flows. This system uses two CCD cameras coupled with an accurate cross-correlation calculation method. An experimental test (based upon three-dimensional displacements) has been carried out to demonstrate the capability of this process to locate the maximum of correlation, and to detect accurately the 3D displacements. Experiments in a well-established turbulent flow have validated the method for quantitative measurements and a comparison with LDV results showed a good agreement in terms of mean and fluctuating velocities. Combined PIV and stereoscopic PIV measurements on a turbulent flow revealed the need to the stereoscopic systems to measure accurate 2D velocity fields. It has been shown that an error of up to 10% in the velocity fluctuation measured by conventional PIV could be attained due to 3D effects in highly turbulent cases. Finally, the digital cross-correlation technique adapted to the determination of small displacements seems to be the most suitable technique for stereoscopic PIV. Received: 22 July 1997/Accepted: 27 January 1998     

Receptivity of the boundary layer on a flat plate with a blunted leading edge to steady nonuniformity of the free stream

The flow past a flat plate with a blunted leading edge by a flow of a viscous incompressible fluid with a small spanwise-periodic, steady nonuniformity of the velocity profile is considered. Such a flow simulates the interaction of one type of vortex disturbances of a turbulent external flow with the boundary layer. The solution obtained predicts generation of strong disturbances in the boundary layer, which are similar to the streaky structure observed in the case of high free-stream turbulence. It is shown that the boundary-layer flow on blunted bodies is more sensitive to vortex disturbances than on a plate with a sharp leading edge. Central Aerohydrodynamic Institute, Zhukovskii, 140160. Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 41, No. 4, pp. 93–100, July–August, 2000.     

Numerical Study of the Flow Behind a Rotary Oscillating Circular Cylinder

A numerical study is performed of flow behind a rotationally oscillating circular cylinder in a uniform flow by solving the two-dimensional incompressible Navier-Stokes equations. The flow behavior in lock-on regime and the timing of vortex formation from the oscillating cylinder are studied. When the frequency of excitation of the cylinder is in the vicinity of the natural vortex formation frequency, a lock-on vortex formation regime appears. As the excitation frequency being increased relative to the natural frequency the initially formed vorticity concentration switches to the opposite side of the cylinder. The effects of oscillating frequency and amplitude on the vortex structures formed in the near wake of the cylinder are also investigated. Based on the present calculated results, some complicated vortex patterns are identified and are consistent with the previous experimental visualizations.     

Modes of vortex formation and transition to three-dimensionality in the wake of a freely vibrating cylinder

The present work is aimed to give some insight into the relation between vortex shedding modes and transition to three-dimensionality in the wake of a freely vibrating cylinder by establishing a numerical model and analyzing the relevant results of two- and three-dimensional simulations. The compressible flow past an elastically-mounted cylinder is solved by using the immersed boundary method (IB method). The cylinder is free to vibrate in the transverse direction with zero structure damping. The response of displacement amplitude is studied with the variation of reduced velocity. Whether P+S mode exists in three-dimensional flow and the occurrence of 2P mode is caused by flow transition from two-dimensional to three-dimensional are problems of concern. Both 2P and P+S wake modes are observed in two- and three-dimensional simulations. The numerical results indicate that the flow transition from two-dimensional to three-dimensional is coupled with the cylinder vibration in the synchronization/lock-in regime. The wake formation given by three-dimensional simulations suggests that the P+S mode might exist in reality when the flow is reverted to two-dimensional by vortex induced vibration (VIV) at Re=300–350. When Reynolds number increases to 425, the wake formation undergoes transition to three-dimensionality and 2P mode is observed. The effect of mass ratio on the flow transition to three-dimensionality is studied. The relationship between wake modes and aerodynamic forces is discussed.     

A Numerical Study of the Flow Around a Model Winged Seed in Auto-Rotation

In this study the flow around a winged-seed in auto-rotation is characterized using direct numerical simulations (DNS) at Reynolds number in the range 80–240, based on the descent speed and a characteristic chord length. In this range, the flow is approximately steady when observed from a reference frame fixed to the seed. For all cases, the flow structure consists of a wing tip vortex which describes a helical path, a vortex shed behind the nut of the seed and a stable leading edge vortex above the wing surface which merges with the tip vortex. With increasing Reynolds number, the leading edge vortex becomes more intense and gets closer to the wing surface. The simulation results also show the formation of a spanwise flow on the upper surface of the wing, moving fluid towards the wing tip in a region downstream and beneath the leading edge vortex. This spanwise flow is rather weak inside the core of the leading edge vortex, and the analysis of the streamlines show a very weak transport of vorticity along the vortex for the cases under consideration. The analysis of the flow suggests that the stabilization of the leading edge vortex is mainly due to non-inertial accelerations, although viscous effects may contribute, specially at lower Re. Furthermore, the leading edge vortex has been characterized by analysing the flow variables averaged along cross-sections of the vortex. While some quantities, like the spanwise velocity or the pressure inside the vortex, are rather insensitive to the threshold used to define the leading edge vortex, the same is not true for the circulation of the vortex or its averaged spanwise vorticity, due to the viscous nature of the vortex. Finally, it is observed that the spanwise vorticity scales with the angular rotation of the seed for the different Re.     

On the origins of vortex shedding in two-dimensional incompressible flows

An exegesis of a novel mechanism leading to vortex splitting and subsequent shedding that is valid for two-dimensional incompressible, inviscid or viscous, and external or internal or wall-bounded flows, is detailed in this research. The mechanism, termed the vortex shedding mechanism (VSM) is simple and intuitive, requiring only two coincident conditions in the flow: (1) the existence of a location with zero momentum and (2) the presence of a net force having a positive divergence. Numerical solutions of several model problems illustrate causality of the VSM. Moreover, the VSM criteria is proved to be a necessary and sufficient condition for a vortex splitting event in any two-dimensional, incompressible flow. The VSM is shown to exist in several canonical problems including the external flow past a circular cylinder. Suppression of the von Kármán vortex street is demonstrated for Reynolds numbers of 100 and 400 by mitigating the VSM.     

On the thrust performance of a flapping two-dimensional elliptic airfoil in a forward flight

In this paper, results of numerical and experimental studies are presented for a flapping two-dimensional (2D)elliptic airfoil in a forward flight condition at a Reynolds number of 5000.The study is motivated by the experiment of Read et al. (2003), which shows that the thrust coefficient of a 2D NACA0012 airfoil deteriorated at high flapping frequency (or Strouhal number) when the induced effective angle of attack profile ceases to be a simple harmonic function in time. As to why non-simple-harmonic profile of effective angle of attack is detrimental to thrust generation is not fully understood. The paper is an attempt to address this issue by examining the flow mechanism, including near field flow structures and the associated transient aerodynamic forces and pressure field, responsible for the observed behavior. Our results show that thrust suppression can be attributed to an adverse suction effect due to high rotation rate of the airfoil and the presence of an attached leading edge vortex generated in the previous stroke. The results further show that the condition for best efficiency need not necessary coincides with the condition of best thrust performance; this observation has been made in past studies of flapping flight.     

Turbulence-driven secondary flows in a curved pipe

If the torque exerted on a fluid element and the source of streamwise vorticity generation are analyzed, a turbulence-driven secondary flow is found to be possible in a curved pipe. Based on this analysis, it is found that the secondary flow is primarily induced by high anisotropy of the cross-stream turbulent normal stresses near the outer bend (furthest from the center of curvature of the bend). This secondary flow appears as a counterrotating vortex pair embedded in a Dean-type secondary motion. Recent hot-wire measurements provide some evidence for the existence of this vortex pair. To verify the formation and extent of this turbulence-driven vortex pair further, a near-wall Reynolds-stress model is used to carry out a detailed numerical investigation of a curved-pipe flow. The computation is performed specifically for a U-bend with a full developed turbulent flow at the bend entrance and a long straight pipe attached to the exit. Numerical results reveal that there are three vortex pairs in a curved pipe. The primary one is the Dean-type vortex pair. Another pair exists near the pipe core and is a consequence of local pressure imbalance. A third pair is found near the outer bend and is the turbulence-driven secondary flow. It starts to appear around 60° from the bend entrance, grows to a maximum strength at the bend exit, and disappears altogether at about seven pipe diameters downstream of the bend. On the other hand, calculations of developing laminar curved-pipe flows covering a range of pipe-to-bend curvature ratios, Reynolds number, and different inlet conditions fail to give rise to a third cell near the outer bend. Therefore, experimental and numerical evidence together lend support to the formation of a pair of turbulence-driven secondary cells in curved-pipe flows.Research supported by the Office of Naval Research under Grant No. N0014-81-K-0428 and by the David Taylor Research Center, Annapolis, Maryland, under Contract No. N00167-86-K0075.     

Self-sustained oscillation and cavitation characteristics of a jet in a Helmholtz resonator

Self-sustained oscillations resulting from a sudden expansion in geometry, as encountered in cavities, occur in a broad array of engineering applications. In the present study, the turbulent flow past a 120°-impinging edge Helmholtz nozzle was investigated. A modified theoretical model accompanied by numerical simulation was proposed to obtain the range of the oscillation frequency and was verified using experimental results. It was found that the cavitation clouds in the chamber dominate the oscillating frequency under the low pressure-high flowrate condition. Based on the simulation results, the details of cavitation development, the motion of vortex structures, and the fluid injection and reinjection were investigated in one typical cycle. The interaction between the cavitation and the vortex formation was analyzed with the vortex transport equation. The dilatation term, which is related to the mass transfer rate through the linkage of velocity divergence, has a high value only around the bulk flow; while the baroclinic torque is predominant due to the unremitting collapse and coalescence of the cavitation clouds.     

Swept-Wing Boundary Layer Receptivity to a Steady Free-Stream Vortex Disturbance

A single trailing vortex developed behind a micro-wing immersed in a free stream was used to study the vortex receptivity of a swept-wing boundary layer. As a result of the interaction, longitudinal-velocity disturbances develop in the boundary layer. On the swept wing, disturbance transformation occurs near the leading edge and is accompanied by the formation of a wave packet consisting of waves typical of cross-flow instability. Disturbances with other characteristics are also detected. These disturbances may be attributable to distributed boundary-layer receptivity to the free-stream vortex disturbance considered.     

A PLIF and PIV study of liquid mixing enhanced by a lateral synthetic jet pair

In this paper, enhancement of mixing between two water streams of the same flow rate in a planar channel by means of a lateral synthetic jet pair is studied at a net flow Reynolds number of 83 using PLIF and PIV. The synthetic jet pair is operated 180° out-of-phase at a range of actuation frequencies and displacements, with the latter being characterized by the dimensionless stroke length. The extent of mixing is evaluated using PLIF data at a location further downstream in the mixing channel. It is found that at a fixed actuation frequency a higher dimensionless stroke length produces a better mixing, and as the actuation frequency increases a lower dimensionless stroke length is required to achieve a given mixing degree. At a sufficiently high frequency or dimensionless stroke length, a nearly homogenous mixing with a mixing degree greater than 0.9 can be obtained. A functional relationship between actuation frequency and dimensionless stroke length is also obtained by best fitting the experimental data, which can be used for selecting the synthetic jet operating conditions to ensure a good mixing. Furthermore, both PLIF and PIV results show that each synthetic jet actuation cycle produce two opposing vortex pairs, which play an important role in prompting mixing between the two fluid streams. The excellent mixing obtained at a high frequency or a high dimensionless stroke length is found to be largely caused by a strong interaction between these opposing vortex pairs.     

Structure of a bathtub vortex: importance of the bottom boundary layer

A bathtub vortex in a cylindrical tank rotating at a constant angular velocity Ω is studied by means of a laboratory experiment, a numerical experiment and a boundary layer theory. The laboratory and numerical experiments show that two regimes of vortices in the steady-state can occur depending on Ω and the volume flux Q through the drain hole: when Q is large and Ω is small, a potential vortex is formed in which angular momentum outside the vortex core is constant in the non-rotating frame. However, when Q is small or Ω is large, a vortex is generated in which the angular momentum decreases with decreasing radius. Boundary layer theory shows that the vortex regimes strongly depend on the theoretical radial volume flux through the bottom boundary layer under a potential vortex : when the ratio of Q to the theoretical boundary-layer radial volume flux Q _b (scaled by ${2\pi R^2 ( \Omega \nu )^\frac{1}{2}}$ ) at the outer rim of the vortex core is larger than a critical value (of order 1), the radial flow in the interior exists at all radii and Regime I is realized, where R is the inner radius of the tank and ν the kinematic viscosity. When the ratio is less than the critical value, the radial flow in the interior nearly vanishes inside a critical radius and almost all of the radial volume flux occurs only in the boundary layer, resulting in Regime II in which the angular momentum is not constant with radius. This criterion is found to explain the results of the laboratory and numerical experiments very well.     

Experimental investigation of the unsteady structure of a transitional plane wall jet

 A laminar wall jet undergoing transition is investigated using the particle image velocimetry (PIV) technique. The plane wall jet is issued from a rectangular channel, with the jet-exit velocity profile being parabolic. The Reynolds number, based on the exit mean velocity and the channel width, is 1450. To aid the understanding of the global flow features, laser-sheet/smoke flow visualizations are performed along streamwise, spanwise, and cross-stream directions. Surface pressure measurements are made to correlate the instantaneous vorticity distribution with the surface pressure fluctuations. The instantaneous velocity and vorticity field measurements provide the basis for understanding the formation of the inner-region vortex and the subsequent interactions between the outer-region (free-shear-layer region) and inner-region (boundary-layer region) vortical structures. Results show that under the influence of the free-shear-layer vortex, the local boundary layer becomes detached from the surface and inviscidly unstable, and a vortex is formed in the inner region. Once this vortex has formed, the free-shear-layer vortex and the inner-region vortex form a vortex couple and convect downstream. The mutual interactions between these inner- and outer-region vortical structures dominate the transition process. Farther downstream, the emergence of the three-dimensional structure in the free shear layer initiates complete breakdown of the flow. Received: 8 November 1995/Accepted: 6 November 1996     

Simulation of 2D external viscous flows by means of a domain decomposition method using an influence matrix technique

Two-dimensional external viscous flows are numerically approximated by means of a domain decomposition method which combines a vortex method and a finite difference method. The vortex method is used in the flow region which is dominated by convective effects, whereas the finite difference method is used in the flow region where viscous diffusion effects are dominant. An influence matrix technique combined with the uniformity condition of the pressure is used to enforce the tangential velocity boundary condition. Comparisons between numerical and experimental data show that the method is well adapted for simulating two-dimensional flows.     

Statistical theory applied to a vortex street generated from meander of a jet

Statistic features of a vortex street formed by instability of a jet are investigated by numerical calculation and statistic theory. A formation process of a vortex street is numerically calculated using a simple barotropic quasi-geostrophic system: a jet in the initial state begins to meander owing to its instability and vortices are formed in both flanks of the jet and become a steady vortex street. Statistic theory of vorticity mixing for two-dimensional fluid, which describes the statistically steady equilibrium state based on the maximum entropy assumption, is applied to the numerically obtained features of the steady vortex street. The theoretically derived relation between stream function and potential vorticity explains the results in the numerical calculation very well. However, in the numerical calculation, there remain regions where the fluid is not mixed well. By calculating mixing process of another scalar, the unmixed region is clearly shown on the physical plane.     

Control of flow distortion in offset diffusers using trapped vorticity

Controlled concentrations of trapped vorticity within an offset, subsonic (M_AIP ≤ 0.7) diffuser are explored for active suppression of flow distortion in joint experimental and numerical investigations. The coupling between trapped vorticity, used to model boundary-layer separation, and secondary-flow vortices is manipulated using an array of fluidic oscillating jets, which are spanwise distributed just upstream of the trapped vortex. Actuation energizes the separated shear layer, reducing the size of separation and effecting an earlier reattachment of the boundary layer, which favorably effects the flow field downstream of reattachment. It is shown that optimal interactions between actuation and the trapped vortex fully suppress the central vortex pair, and redistributes the residual vorticity around the diffuser's circumference. This results in a 68% reduction in circumferential distortion at the Aerodynamic Interface Plane (AIP), using an actuation mass flow rate that is only 0.25% of the diffuser mass flow rate.     

An experimental study of a spanwise structure around a reattachment region of a two-dimensional backward-facing step

 The flow field downstream of a two-dimensional backward-facing step is usually assumed to be independent of the direction along the span of the step. This assumption is made even though it is well known that the flow exhibits a three-dimensional vortex structure. This state of affairs is no doubt due to the lack of detailed information concerning the characteristics of the vortex structure. In this paper, we report our investigations of the flow structure around a reattachment region using an ultrasound velocity profiler to measure the spanwise velocity component as a function of the spanwise coordinate and time. The flow field is found to be very complex both in space and time. The low-frequency component of the spanwise velocity fluctuation becomes dominant in the near-wall region, with peaks in the power spectrum at frequencies fh/Uc=0.05 and fh/Uc=0.012. Using multiple ultrasound transducers, we also find that a streamwise vortex exists in the flow. Received: 20 March 2000 / Accepted: 15 January 2001 Published online: 29 November 2001