Influence of the oxygen concentration on the formation of crystalline phases of TiO<Subscript>2</Subscript> during the low-pressure arc-discharge plasma synthesis

The synthesis of titanium dioxide (TiO₂) nanoparticles with different percentage of anatase and rutile phases is investigated. The synthesis is performed by controlling the oxygen percentage in the gas mixture in the plasmachemical evaporation–condensation process employing a low-pressure arc discharge. In all our experiments, the pressure in the plasmachemical reactor and the average size of particles remain constant and are 60 Pa and 6 nm, respectively. The crystal structure of synthesized TiO₂ is studied using X-ray diffraction; the morphology of the particles is analyzed employing transmission electron microscopy. Using X-ray phase analysis, it is established that the concentration of the TiO₂ anatase phase decreases upon a decrease in the oxygen concentration in the gas mixture. It is shown that the TiO₂ anatase phase is more efficient for photocatalytic decomposition of methylene blue than the rutile phase.     

Effect of ambient pressure on the crystalline phase of nano TiO2 particles synthesized by a dc thermal plasma reactor

The synthesis of nanoparticles of titanium dioxide (TiO₂) with varying percentages of anatase and rutile phases is reported. This was achieved by controlling the operating pressure in a transferred-arc, direct current thermal plasma reactor in which titanium vapors are evaporated, and then exposed to ambient oxygen. The average particle size remained around 15 nm in each case. The crystalline structure of the as-synthesized nanoparticles of TiO₂ was studied with X-ray diffraction analysis; whereas the particle morphology was investigated with the help of transmission electron microscopy. The precursor species responsible for the growth of these nanoparticles was studied with the help of optical emission spectroscopy. As inferred from the X-ray diffraction analysis, the relative abundance of anatase TiO₂ was found to be dominant when synthesized at 760 Torr, and the same showed a decreasing trend with decreasing chamber pressure. The study also reveals that anatase TiO₂ is a more effective photocatalytic agent in degrading methylene blue by comparison to its rutile phase.     

Investigation into the effects of deposition parameters on TiO2 photocatalyst thin films by rf magnetron sputtering

Titanium dioxide (TiO₂) photocatalyst thin films were deposited on non-alkali glass substrates by radio frequency (rf) magnetron sputtering. The Taguchi method with orthogonal array, signal-to-noise ratio and analysis of variance were employed to study the performance characteristics. The experimental studies were conducted under different rf powers, sputtering pressures, O₂/(Ar+O₂) flow-rate ratios, and substrate temperatures. The deposited TiO₂ films were of the anatase phase with a (101) preferred orientation. We performed both photoinduced decomposition of methylene blue (MB) and photoinduced hydrophilicity under UV light illumination. With the optimized TiO₂ photocatalyst thin film deposition conditions, the water contact angle after 9 min UV illumination was approximately 5, the absorbance of MB was reduced to 0.2 for 240 min UV irradiation, and the deposition rate was 34.18 Å/min.     

Photocatalytic property of TiO2 thin films sputtered-deposited on unheated substrates

TiO₂ films deposited on unheated substrates of alumina silicate glass by rf. (13.56 MHz) magnetron sputtering in the mixture of O₂ and Ar gases have been studied with X-ray diffraction (XRD), Atomic Force Microscopy (AFM) and optical spectroscopy. Structural and optical properties of TiO₂ films deposited at different O₂ concentrations and total pressures have been analyzed. Photocatalytic properties of TiO₂ films were characterized by following the degradation of methylene blue molecules under UV irradiation. It was found that the rate of methylene blue decomposition strongly depends on morphology and crystallinity of the deposited films, namely on the content of the anatase phase and on the size of the anatase grains. The best photocatalytic activity was found on TiO₂ films consisting of pure anatase phase with the size of grains of about 450 Å. With the help of those films a thin film reactor for water purification has been designed and tested.     

Photocatalytic activity enhancement of Dy-doped TiO2 nanoparticles hybrid with TiO2 (B) nanobelts under UV and fluorescence irradiation

The main drawbacks of anatase titanium dioxide (TiO₂) nanoparticles for being used as a photocatalyst are due to the rapid charge recombination of the electron-hole pairs and the wide band gap energy, limiting its photocatalysis application. To enhance photocatalytic activity, structure modification was performed here. Heterogeneous nanostructure of Dy-doped TiO₂ nanoparticles hybrid with Monoclinic TiO₂ nanobelts (Dy/TNBs) was fabricated via hydrothermal method. Annealing temperature was varied to investigate its effect on phase composition and morphology of the as-prepared TiO₂ catalyst. Phase composition and morphology were studied by XRD and SEM, respectively. The effect of amount of catalyst loaded on the degradation efficiency of methylene blue (MB) dye in aqueous solution under UV and fluorescence illumination was investigated. The results showed that pure monoclinic TiO₂ nanobelts (TNBs) was achieved at 450 °C. Enhanced photocatalytic activity under both UV and fluorescence irradiation was found on Dy/TNB samples. The optimum Dy dosage providing the highest MB degradation rates under both irradiation sources was 0.1 mol%.     

Improved visible light photocatalytic activity of TiO<Subscript>2</Subscript> nano powders with metal ions doping for glazed ceramic tiles

Self-cleaning and anti-bacterial activities of the photo-catalyst titanium dioxide make it a superior compound for use in the ceramics and glass industry. In order to achieve high self-cleaning efficiency for building products, it is important that Titania is present as anatase phase. Moreover, it is desirable that the particle sizes are in Nano-range, so that a large enough surface area is available for enhanced catalytic performance. In the present paper, Cobalt and Nickel co-doped (4%mol Ni and 4%mol Co doped TiO₂) and un-doped TiO₂ Nano powders have been prepared by sol–gel technique. They were calcined at the temperatures in the range of 475–1075 °C. Ni/Co co-doped TiO₂ postponed the anatase to rutile transformation of TiO₂ by about 200–300°C, such that before calcination at 775°C, no rutile was detected for 4 mol% Ni/Co co-doped TiO₂. A systematic decreasing on crystallite size and increasing on specific surface area of Ni/Co co-doped TiO₂ were observed. Photo-catalytic activity of anatase polymorph was measured by the decomposition rate of methylene blue under visible light. The results showed enhanced catalysis under visible light for Ni/Co co-doped TiO₂ as compared to pure TiO₂. The enhanced performance was attributed to surface chemistry change associated with a slight shift in the band gap. Depending on the temperatures ranging from 475 to 1075 °C, band gap energy of Ni and Co doped TiO₂ crystals decreased. For all samples there is a general reduction of the band gap energy from 3.00 to 2.96 eV.     

Preparation and characterization of Cobalt Sulfophthalocyanine/TiO2/fly-ash cenospheres photocatalyst and study on degradation activity under visible light

Cobalt Sulfophthalocyanine (CoSPc) sensitized TiO₂ sol samples were prepared through a Sol-Gel method using Cobalt Sulfophthalocyanine as a sensitizer. Loading and modified floating photocatalyst was prepared by hydrothermal method using fly-ash cenospheres as a carrier. The properties of the samples were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) and UV-vis diffuse reflectance spectrum (DRS). Photocatalytic activity was studied by degrading wastewater of methylene blue under visible light. The results indicate that the fly-ash cenospheres are covered by modified TiO₂ film which composed of the anatase, brookite and rutile misch crystal phase. CoSPc/TiO₂/fly-ash cenospheres samples have good catalytic activity under visible light, and have strong absorbency during 600-700 nm. The sensitization of CoSPc can enhance visible light catalytic activity of TiO₂/fly-ash cenospheres. The degradation rate of methylene blue reaches 73.36% in 180 min under the visible light illumination. But too much CoSPc can decrease its catalytic activity.     

Titania Gold Composite: Effect of Illumination on Size of Gold Nanoparticles with Consequent Implication on Photocatalytic Water Splitting

This work deals with the study of photodeposition (PD) of gold nanoparticles (AuNPs) on TiO₂ by using different illumination sources, Medium pressure Mercury lamp (ML), Solar Simulator equipped with AM 1.5 (SL) and Tungsten lamp (WL). Different particle size of AuNPs on TiO₂ were obtained by photodeposition method under different illumination sources, which clearly proves the influence of light source on the synthesis of Au–TiO₂. The plasmonic activity of Au–TiO₂ photocatalyst for water splitting reaction was observed to be strongly influenced by the particle size of Au as well as illumination source. Amongst the three different illumination sources used, smallest particle size for AuNP–TiO₂ were observed under ML followed by SL and WL, as revealed by TEM analysis. Different illumination sources were also investigated to evaluate the activity of Au–TiO₂ samples thus prepared under different illumination conditions. The order of hydrogen evolution rate (HER) observed for Au–TiO₂ with different source of illuminations is ML > SL > WL. The highest HER of 1709 μmol/h was observed for Au–TiO₂, which was synthesized and evaluated under ML irradiation. This may be explained on the basis of reduced catalytic activity and photothermal effect of Au nanoparticles with increasing particle size.     

Effect of N2 ion flux on the photocatalysis of nitrogen-doped titanium oxide films by electron-beam evaporation

Nitrogen-doped titanium oxide (TiO_xN_y) films were prepared with ion-assisted electron-beam evaporation. The nitrogen (N) incorporated in the film is influenced by the N₂ flux modulated by the N₂ flow rate through an ion gun. The TiO_xN_y films have the absorption edge of TiO₂ red-shifted to 500 nm and exhibit visible light-induced photocatalytic properties in the surface hydrophilicity and the degradation of methylene blue. The structures and states of nitrogen in the films are investigated by X-ray diffraction patterns (XRD), and X-ray photoelectron spectroscopy (XPS) and related to their visible light-induced photocatalytic properties. The results indicate that the substitutional N in anatase TiO₂ can induce visible light photocatalysis. The substitutional N is readily doped by the energetic nitrogen ions from the ion gun. The best photocatalytic activity is obtained at the largest N loading about 5.6 at.%, corresponding to the most substitutional N in anatase TiO₂. The film exhibits the degradation of methylene blue with a rate-constant (k) about 0.065 h⁻¹ and retaining 7° water contact angle on the surface under visible light illumination.     

A facile method to synthesize nitrogen and fluorine co-doped TiO2 nanoparticles by pyrolysis of (NH4)2TiF6

The nitrogen and fluorine co-doped TiO₂ (N-F-TiO₂) nanoparticles of anatase crystalline structure were prepared by a facile method of (NH₄)₂TiF₆ pyrolysis, and characterized by thermogravimetry-differential thermal analysis (TG-DTA), X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and ultraviolet visible (UV-Vis) spectroscopy etc. With the increase of calcination temperature, (NH₄)₂TiF₆ decomposed into TiOF₂ and NH₄TiOF₃ at first, and then formed anatase-type TiO₂ with thin sheet morphology. H₃BO₃ as oxygen source can promote the formation of anatase TiO₂, but decrease the F content in the N-F-TiO₂ materials due to the formation of volatile BF₃ during the precursor decomposition. The photocatalytic activity of the obtained N-F-TiO₂ samples was evaluated by the methylene blue degradation under visible light, and all the samples exhibited much higher photocatalytic activity than P25. Moreover, the merits and disadvantages of this proposed method to prepare doped TiO₂ are discussed.     

Estimation of contact area of nanoparticles in chains using continuum elastic contact mechanics

In this research, we have studied the doping behaviors of eight transition metal ion dopants on the crystal phase, particle sizes, XRD patterns, adsorption spectra, anatase fraction, and photoreactivity of TiO₂ nanoparticles. The pristine and ion-doped TiO₂ nanoparticles of 15.91-25.47 nm were prepared using sol–gel method. Test metal ion concentrations ranged from 0.00002 to 0.2 at.%. The absorption spectra of the TiO₂ nanoparticles were characterized using UV-Visible spectrometer. The wavelength of the absorption edge of TiO₂ was estimated using the spectra derivative-tangent method. The photoreactivities of pristine and ion-doped TiO₂ nanoparticles under UV irradiation were quantified by the decoloring rate of methyl orange. XRD patterns were recorded using a Rigaku D/MAX-2500 V diffractometer with Cu Kα radiation (50 kV and 250 mA), and particle size and anatase fraction were calculated. Results reveal that different ion doping exhibited complex effects on the studied characteristics of TiO₂ nanoparticles. In general, red shift occurred to ion-doped TiO₂ nanoparticles, but still with higher TiO₂ photoreactivities when doped with Fe³⁺ and Ni²⁺ ions. Among the ions investigated, Ni-doped TiO₂ nanoparticles have shown highest photoreactivity at the concentration of 0.002 at.%, about 1.9 times that of the pristine TiO₂. Ion doping was shown to reduce the diameter and influence the fraction of anatase. Data also indicated that the combination of anatase diameter and ion radius might play an important role in the photoreactivity of TiO₂ nanoparticles. This investigation contributes to the understanding of complex ion doping effects on TiO₂ nanoparticles, and provides references for enhancing their environmental application.     

Synergetic Photocatalytic Nanostructures Based on Au/TiO2/Reduced Graphene Oxide for Efficient Degradation of Organic Pollutants

Recently, there is crucial interest in the design and fabrication of nanocatalysts for efficient decomposition of organic pollutants in wastewater using visible light. This work reports the assembling fabrication of synergetic photocatalytic Au/TiO₂/RGO nanostructures by utilizing the reduced graphene oxide (RGO) as substrate material and efficient separator for electrons and holes. The Au/TiO₂ nanostructures with a ≈7 nm TiO₂ particles size are dispersed uniformly on RGO nanosheets. UV–vis diffuse reflectance spectroscopy verifies that Au/TiO₂/RGO nanocomposites show strong absorption of visible light. The degradation efficiency after 1 h for hydroquinone under visible light and UV light is ≈77% and ≈90%, respectively. Under visible light, the calculated apparent rates (k ) of the Au/TiO₂/RGO nanocomposites are 0.0112 and 0.0174 min^?1 for decomposition of methylene blue and hydroquinone. That are five times greater than that of bare TiO₂. The high photocatalytic activity is mainly attributed to the synergy between RGO and Au/TiO₂ nanostructure. The strategy of composite nanostructures assembling on RGO is ensured to have a great practicable potential for the designing of high efficient multielement composite nanoparticles catalysts.     

Photocatalytic thin films containing TiO2:N nanopowders obtained by the layer-by-layer self-assembling method

In this work, TiO₂-N powders were synthesized by high-energy ball milling, using commercial titanium dioxide (TiO₂) in the anatase phase and urea to introduce nitrogen into TiO₂ in order to enhance their photocatalytic properties in the visible spectral region. Several samples were prepared by milling a mixture of TiO₂-urea during 2, 4, 8, 12 and 24 h and characterized by spectroscopic and analytical techniques. X-ray diffraction (XRD) results showed the coexistence of anatase and high-pressure srilankite TiO₂ crystalline phases in the samples. Scanning electron microscopy (SEM) revealed that the grain size of the powder samples decreases to 200 nm at 24 h milling time. UV-Vis diffuse reflectance spectroscopic data showed a clear red-shift in the onset of light absorption from 387 to 469 nm as consequence of nitrogen doping in the samples. The photocatalytic activity of the TiO₂-N samples was evaluated by methylene blue degradation under visible light irradiation. It was found that TiO₂-N samples had higher photocatalytic activity than undoped TiO₂ samples, which could be assigned to the effect of introducing N atoms and XPS results confirm it. Using polyethylenimine (PEI), transparent thin films of TiO₂-N nanoparticles were prepared by layer-by-layer self assembly method. UV-visible spectrophotometry was employed in a quantitative manner to monitor the adsorbed mass of TiO₂ and PEI after each dip cycle. The adsorption of both TiO₂ and PEI showed a saturation dip time of 15 min.     

TiO<Subscript>2−<Emphasis Type="Italic">x</Emphasis></Subscript> nanoparticles synthesized using He/Ar thermal plasma and their effectiveness on low-concentration mercury vapor removal

Oxygen-vacant titanium dioxide (TiO_2−x ) nanoparticles were synthesized using thermal plasma as a heating source at various applied plasma currents and He/Ar ratios. Samples with diverse characteristics were developed and the mercury removal effectiveness was subsequently evaluated. TiO₂ nanoparticles possessing high purity and uniform particle sizes were successfully synthesized using metal titanium and O₂ as precursors and Ar as plasma gas. TiO_2−x in anatase phase with a particle size at 5–10 nm was formed at the He/Ar volume ratio of 25/75. Further increasing the He/Ar ratio elevated the plasma temperature, causing the tungsten to melt, vaporize from the cathode, and then dope into the formed TiO₂ nanoparticles. The doped W appeared to inhibit the growth of nanoparticles and decrease the crystallinity of formed anatase. The effectiveness of oxygen-vacant sites on Hg⁰ removal under the visible light circumstance was confirmed. Hg⁰ removal by the TiO_2−x nanoparticles was enhanced by increasing the O₂ concentration. However, moisture reduced Hg⁰ capture, especially when light irradiation was applied. The reduction in Hg⁰ capture may be resulted from the competitive adsorption of H₂O on the active sites of TiO_2−x with Hg⁰ and transformed Hg²⁺.     

Nanostructured TiO<Subscript>2</Subscript> Films with a Mixed Phase for Perovskite Solar Cells

A series of thin films made with TiO₂ nanoparticles with a varied anatase/rutile phase ratio is prepared on conducting glass substrates using a spin-coating method. The structure, morphology, and optical properties of TiO₂ nanopowders and thin films fabricated are studied using powder X-ray diffraction, scanning electron microscopy, and optical spectroscopy. The TiO₂ nanostructured films created are used as photoelectrodes for the fabrication of perovskite solar cells (PSCs). The photovoltaic characteristics of PSCs under AM1.5 light illumination (1000 W/m²) under ambient conditions are studied. It is shown that the best efficiency of solar-to-electrical energy conversion, namely, 9.3%, is obtained for the PSC with a photoelectrode based on a TiO₂ film with an anatase/rutile mixed phase ratio of 86/14%.     

Optical and structural properties of TiO<Subscript>2</Subscript> nanopowders with Ce/Sn doping at various calcination temperature and time

In this paper, the influence of calcination temperature and time has been investigated on the structural, morphological, optical, and photo-catalytic properties of Sn/Ce co-doped TiO₂ nano-powders prepared via sol–gel process. They were calcined at the temperatures in the range of 475–975 °C for 1 and 2 h. The photocatalytic ability of TiO₂ powders was evaluated by means of methylene blue degradation experiments conducted under the irradiation of simulated solar light. The X-ray diffraction results showed that the tensile strain in the host lattice was present. The comparison with undoped and Sn or Ce-doped TiO₂, co-doped TiO₂ shows an obviously higher catalytic activity under visible light irradiation. The absorbance spectrum of Ce and Sn co-doped TiO₂ exhibited significant red-shift to visible region. The red-shift is caused by the appearance of a new electronic state in the middle of the TiO₂ band-gap. FESEM images show the formation of doped TiO₂ nanoparticles with small size in structure and spherical in shape. The FTIR spectra exhibited peaks corresponding to the anatase and rutile structure phases of TiO₂.     

Hydrothermal synthesis of well-dispersed ultrafine N-doped TiO2 nanoparticles with enhanced photocatalytic activity under visible light

Ultrafine nitrogen-doped TiO₂ nanoparticles with narrow particle size distribution, good dispersion, and high surface area were synthesized in the presence of urea and PEG-4000 via a hydrothermal procedure. TEM observation, N₂ adsorption, XRD, UV-vis spectroscopy, the Raman spectroscopy and XPS analysis were conducted to characterize the synthesized TiO₂ particles. The synthesized TiO₂ particles were a mixture of 49.5% anatase and 50.5% rutile with a size of around 5 nm. The photocatalytic activities were tested in the degradation of an aqueous solution of a reactive Brilliant Blue KN-R under both UV and visible light. The synthesized TiO₂ particles showed much higher photocatalytic activity than a commercial P25 TiO₂ powder under both UV and visible light irradiations. The high performance is associated to N doping, the reduced particle size, good dispersion, high surface area, and a quantum size effect.     

热处理对爆轰合成的纳米TiO_2混晶的结构相变的影响

采用爆轰法制备了纳米TiO2混晶体,初步研究了不同煅烧温度(600℃和720℃)和不同煅烧时间(1 h,2 h,3.5 h和5 h)对其微结构和结构相变行为的影响,并应用热动力学理论讨论了从锐钛矿相到金红石相的结构相变过程和相变机理.研究表明:随着煅烧温度的升高和煅烧时间的增加,纳米TiO2的粒径逐渐增大,混晶中金红石相的含量逐渐提高.与常规方法制备的纳米TiO2不同的是,在相同煅烧温度和煅烧时间下金红石相的平均生长速率明显低于锐钛矿相.锐钛矿相完全相变为金红石的温度也明显低于常规方法报道的相变温度.该研究会对控制纳米TiO2晶体尺寸和批量合成提供一定的理论和实验指导.     

Aerosol characterization and lung deposition of synthesized TiO2 nanoparticles for murine inhalation studies

This study presents a novel exposure protocol for synthesized nanoparticles (NPs). NPs were synthesized in gas phase by thermal decomposition of metal alkoxide vapors in a laminar flow reactor. The exposure protocol was used to estimate the deposition fraction of titanium dioxide (TiO₂) NPs to mice lung. The experiments were conducted at aerosol mass concentrations of 0.8, 7.2, 10.0, and 28.5 mg m^?3. The means of aerosol geometric mobility diameter and aerodynamic diameter were 80 and 124 nm, and the geometric standard deviations were 1.8 and 1.7, respectively. The effective density of the particles was approximately from 1.5 to 1.7 g cm^?3. Particle concentration varied from 4 × 10⁵ cm^?3 at mass concentrations of 0.8 mg m^?3 to 12 × 10⁶ cm^?3 at 28.5 mg m^?3. Particle phase structures were 74% of anatase and 26% of brookite with respective crystallite sized of 41 and 6 nm. The brookite crystallites were approximately 100 times the size of the anatase crystallites. The TiO₂ particles were porous and highly agglomerated, with a mean primary particle size of 21 nm. The specific surface area of TiO₂ powder was 61 m² g^?1. We defined mice respiratory minute volume (RMV) value during exposure to TiO₂ aerosol. Both TiO₂ particulate matter and gaseous by-products affected respiratory parameters. The RMV values were used to quantify the deposition fraction of TiO₂ matter by using two different methods. According to individual samples, the deposition fraction was 8% on an average, and when defined from aerosol mass concentration series, it was 7%. These results show that the exposure protocol can be used to study toxicological effects of synthesized NPs.     

Synthesis of TiO2/WO3 nanoparticles via sonochemical approach for the photocatalytic degradation of methylene blue under visible light illumination

Through an ultrasound assisted method, TiO₂/WO₃ nanoparticles were synthesized at room temperature. The XRD pattern of as-prepared TiO₂/WO₃ nanoparticles matches well with that of pure monoclinic WO₃ and rutile TiO₂ nanoparticles. TEM images show that the prepared TiO₂/WO₃ nanoparticles consist of mixed square and hexagonal shape particles about 8–12 nm in diameter. The photocatalytic activity of TiO₂/WO₃ nanoparticles was tested for the degradation of a wastewater containing methylene blue (MB) under visible light illumination. The TiO₂/WO₃ nanoparticles exhibits a higher degradation rate constant (6.72 × 10⁻⁴ s⁻¹) than bare TiO₂ nanoparticles (1.72 × 10⁻⁴ s⁻¹) under similar experimental conditions.