A Low Noise NbTiN-Based 850 GHz SIS Receiver for the Caltech Submillimeter Observatory

We have developed a niobium titanium nitride (NbTiN) based superconductor-insulator-superconductor (SIS) receiver to cover the 350 micron atmospheric window. This frequency band lies entirely above the energy gap of niobium (700 GHz), a commonly used SIS superconductor. The instrument uses an open structure twin-slot SIS mixer that consists of two Nb/AlN/NbTiN tunnel junctions, NbTiN thin-film microstrip tuning elements, and a NbTiN ground plane. The optical configuration is very similar to the 850 GHz waveguide receiver that was installed at the Caltech Submillimeter Observatory (CSO) in 1997. To minimize front-end loss, we employed reflecting optics and a cooled beamsplitter at 4 K. The instrument has an uncorrected receiver noise temperature of 205K DSB at 800 GHz and 410K DSB at 900 GHz. The degradation in receiver sensitivity with frequency is primarily due to an increase in the mixer conversion loss, which is attributed to the mismatch between the SIS junction and the twin-slot antenna impedance. The overall system performance has been confirmed through its use at the telescope to detect a wealth of new spectroscopic lines.     

Simple FTS Measurement System for Submillimeter SIS Mixer

We have constructed a simple Fourier Transform Spectroscopy system, and carried out performance measurement of our 640-GHz band SIS mixer devices. This system uses the identical quasi-optics to the one for heterodyne measurement, which allows a direct and quick comparison between FTS and heterodyne responses. With a room-temperature absorber for submillimeter source, instead of a high-temperature source such as Hg lamp, we successfully obtained interferogram with good signal-to-noise ratios. The frequency resolution is moderately coarse ( 17 GHz( due to a limitation on the travel length of scanning mirror for the interferometer, but we found it is useful to investigate broad-band characteristics of SIS mixers.     

An Accurate Method for Determining the IF Noise in SIS Heterodyne Receivers

We present a new method to determine the contribution of the IF-amplifier chain to the overall noise performance of an SE-based receiver. Using simulated I-V and IF power characteristics, we show that the standard method used to date to evaluate the IF noise can underestimate the contribution because of non-negligible curvature in the post-gap SIS I-V characteristic. We demonstrate that the new method is not susceptible to the post-gap curvature, and discuss its benefits and limitations to the accurate and precise evaluation of IF noise contributions.     

A Multibeam SIS Mixer Module for a Focal Plane Array Receiver

The integration of many receiver units into a receiver array is a common method of improvement of imaging systems. This approach, well known in the mm band for Schottky mixer arrays, has not so far been developed for Superconductor - Insulator - Superconductor (SIS) junction mixers, which give the best sensitivity in the short mm wave range and in the submm range.We demonstrate for the first time a practical low noise multibeam receiver module using SIS mixer technology. The basis for the integration of several SIS mixers with a common local oscillator source is given by the saturation of the SIS receiver noise dependence upon local oscillator power. The module comprises three identical SIS mixers integrated with a common local oscillator, coupled through a three branch waveguide directional coupler. The multibeam module has been developed for a focal plane array receiver of the 30 meter radio telescope of the Institut de Radioastronomie Millimétrique (IRAM).     

345 GHZ PROTOTYPE SIS MIXER WITH INTEGRATED MMIC LNA

We report on heterodyne measurements at submillimeter wavelengths using a receiver with a Superconductor-Insulator-Superconductor (SIS) mixer device and a Microwave Monolithic Integrated Circuit (MMIC) cryogenic low noise amplifier (LNA) module integrated into the same block. The mixer characterization presented in this work demonstrates the feasibility of operating a MMIC LNA in close proximity to the SIS device without penalty in mixer performance due to heating effects. Verification of this functionality is crucial for the ongoing development of SuperCam, a 64-pixel focal plane array receiver consisting of eight, 1 × 8 integrated mixer/LNA modules. The test setup included a mixer block modified to accept a MMIC amplifier. Our tests show that the LNA can be operated over a broad range of V_drain voltages from 0.40–1.40 V, corresponding to dissipative powers of 2.6–29 mW. We observe no significant effect on the measured uncorrected receiver noise temperatures in the 345 GHz band.     

Low noise submillimeter SIS receiver with niobium nitride quasiparticle tunnel junctions

We have developed and tested a submillimeter waveguide SIS mixer with NbN-MgO-NbN quasiparticle tunnel junctions. The two junction array is integrated in a full NbN printed circuit. The NbN film critical temperature is 15 K and the junction gap voltage is 5 mV. The size of the junctions is 1.4 × 1.4 µm and Josephson critical current density is about 1.5 KA/cm² resulting in junction R_NC product about 40. The inductive tuning circuit in NbN is integrated with each junction in two junction array. A single non contacting backshort was tuned at each frequency in the mixer block.At 306 GHz the minimum DSB receiver noise temperature is as low as 230 K. The sources of the receiver noise and of the limits of the NbN SIS submillimeter mixer improvement are discussed.     

The Development of a Dual Channel SIS Receiver of Trao Telescope

We developed a low noise dual channel receiver with 100GHz and 150GHz band, which is used to make the simultaneous observation with two bands. The SIS mixers are used in both bands. The constructed dewar for the receiver has a performance with a vacuum of 10^–8torr and a temperature of 4.2K. The receiver noise temperature is 50K(DSB) for 100GHz band and 80K(DSB) for 150GHz band, respectively. In order to achieve the simultaneous observations, the quasioptical system is precisely designed, and also evaluated by measurements in the laboratory. The relative pointing offset between two bands is 3. We have observed the various sources using the receiver since October 1998.     

Minimum noise temperature of a practical SIS quantum mixer

Noise temperature of a SIS quantum mixer has been calculated as function of local oscillator voltage and signal source conductance on the basis of a measured I–V characteristic. Applying Tucker's quantum theory of mixing /1/, it is shown that the SIS mixer is quantum noise limited. Using cryogenic intermediate frequency amplifier, receiver noise temperature of 20 K seems to be possible at mm wavelength.     

A Fixed Tuned Low Noise 600-700 GHz SIS Receiver

We have designed and fabricated a fixed tuned low noise 600-700 GHz SIS mixer. Twin junctions connected in parallel was employed in the mixer design. A short microstrip tuning structure was used to minimize the RF signal loss at frequency above the energy gap. A receiver noise temperature below 200 K (without any loss correction) in the frequency range of 630 to 660 GHz was recorded. The lowest noise temperature of the receiver was 181 K (without any loss correction) at 656 GHz.     

A 650-GHz Band SIS Receiver for Balloon-Borne Limb-Emission Sounder

A superconducting low-noise receiver has been developed for atmospheric observations in the 650-GHz band. A waveguide-type tunerless mixer mount was designed based on one for the 200-GHz band. Two niobium SIS (superconductor-insulator-superconductor) junctions were connected by a tuning inductance to cancel the junction capacitance. We designed the R_nC_j product to be 8 and the current density to be 5.5 kA/cm². The measured receiver noise temperature in DSB was 126-259 K in the frequency range of 618-660 GHz at an IF of 5.2 GHz, and that in the IF band (5-7 GHz) was 126-167 K at 621 GHz. Direct detection measurements using a Fourier transform spectrometer (FTS) showed the frequency response of the SIS mixer to be in the range of about 500-700 GHz. The fractional bandwidth was about 14%. The SIS receiver will be installed in a balloon-borne limb-emission sounder that will be launched from Sanriku Balloon Center in Japan.     

Production of high quality Nb/Al-oxide/Nb SIS trilayers for submillimeter wave mixers

Owing to a very sharp nonlinearity in the quasiparticle currentvoltage characteristic, which fortuitously occurs on the scale of a few millivolts rather than a few volts as with semiconductor devices, superconductor/insulator/superconductor (SIS) tunnel junctions are the most sensitive detectors for heterodyne mixing at millimeter and submillimeter wavelengths. They can also provide sources of coherent local oscillator power at very high frequencies; more broadly, they have a number of interesting applications as fast, low-power logic elements and as detectors at optical wavelengths. For submillimeterwave mixers, in many ways the most demanding of these applications, the Nb/Al-oxide/Nb material system has emerged as the system of choice to frequencies of ∼ 700 GHz and beyond. Production of SIS devices requires careful attention to a number of critical microfabrication issues, and I describe here some of the insights gained from developing a process for high-quality niobium trilayers that successfully yielded small-area junctions with unusually low sub-gap leakage current.     

Low noise SIS mixer for 230 GHz receivers of plateau de bure interferometer

We present a SIS mixer developed for 200 – 250 GHz band receivers of Plateau de Bure Interferometer. We demonstrate the minimum DSB receiver noise of 20 K at 220 GHz. The average receiver noise of 25 K is possible in 200 – 250 GHz range. The receiver conversion gain and output noise instability of 10⁻⁴ on the time scale of 1 minute is comparable with the Shottky receivers performance. The minimum measured SIS mixer noise of about 10 K is close to the quantum limit. The waveguide SIS mixer with a single backshort has two junction array with inductively tuned junctions. The Nb/Al Oxide/Nb SIS junctions are 2.24 μm² each with the Josephson critical current density of 3.2 KA/cm². The thermal properties of the SIS mixer are studied. The mixer band of the low noise operation is in a good agreement with the design requirements.     

Development of SRAO 3MM SIS Receiver

We have developed a 3 mm band receiver for SRAO. The receiver employs an Nb-based SIS junction in the mixer and operates at 85–115 GHz with single polarization. The receiver noise temperature is 40–50 K in DSB. It is equipped with an MPI-type filter for single-side band observations. We present the design, construction, and test results for individual components of the receiver optics, heterodyne system, and cryogenics. The receiver has been installed on the 6 m SRAO telescope and tested toward astronomical sources. The beam-measurement experiment suggests that the edge taper is smaller than the designed 12 dB.     

Low Noise Quasi-Optic Receiving in Millimeter and Submillimeter Range for Geophysical and Radio Telescope Measurements

This paper is focused on the choice of the module for low noise receiver in millimeter (mm) and sub millimeter (submm) wave ranges used in geophysical remote sensing systems for measurement of geophysical parameters by means of radiobrightness temperatures (radiometer systems obtaining data by means of radiobrightness temperatures). The observed data analysis, used in order to obtain recommendations and forecasts based on the radio telescope measurements and geophysical phenomena in the events of earthquakes, volcano explosions and typhoons, are realized by means of specialized computer codes.     

A Low-Noise 230 GHz SIS Receiver for Radio Astronomy Employing Untuned Nb/AlOx/Nb Tunnel Junctions

A heterodyne receiver based on a 1/3 reduced height rectangular waveguide SIS mixer with two mechanical tuners has been built for astronomical observations of molecular transitions in the 230 GHz frequency band. The mixer used an untuned array (R_nC_j3, R_n70 ) of four Nb/AIOx/Nb tunnel junctions in series as a nonlinear mixing element. A reasonable balance between the input and output coupling efficiencies has been obtained by choosing the junction number N=4. The receiver exhibits DSB (Double Side Band) noise temperature around 50 K over a frequency range of more than 10 GHz centered at 230 GHz. The lowest system noise temperature of 38 K has been recorded at 232.5 GHz. Mainly by adjusting the subwaveguide backshort, the SSB (Single Side Band) operation with image rejection of 15 dB is obtained with the noise temperature as low as 50 K. In addition, the noise contribution from each receiver component has been studied further. The minimum SIS mixer noise temperature is estimated as 15 K, pretty close to the quantum limit v/k11 K at 230 GHz. It is believed that the receiver noise temperatures presented are the lowest yet reported for a 230 GHz receiver using untuned junctions.     

Characterization of Nb-Based Superconducting Microstrip Lines Around the Gap Frequency

Submillimter-wave SIS (superconductor-insulator-superconductor) mixers usually adopt SIS junctions associated with an integrated tuning circuit, which tunes out the junction's geometric capacitance and is typically an inductive thin-film superconducting microstrip line. This paper mainly investigates the characteristic of Nb-based superconducting microstrip lines around the junction's gap frequency, at which the surface resistance of Nb films becomes considerable, and its effect on the performance of SIS mixers.     

Noise Stability of SIS Receivers

There is a strong interest in the submillimeter astronomy community to increase the IF bandwidth of SIS receivers in order to better facilitate broad spectral linewidth and continuum observations of extragalactic sources. However, with an increase in receiver IF bandwidth there is a decrease in the mixer stability. This in turn effects the integration efficiency and quality of the measurement. In order to better understand the noise mechanisms responsible for reducing the receiver stability, we employed a technique first described by D.W. Allan and later elaborated upon by Schieder et al. In this paper we address a variety of factors that degrade the noise stability of SIS receivers. The goal of this exercise is to make recommendations aimed at maximizing SIS receiver stability.     

Noise and thermal properties of a submillimeter mixer with the SINS tunnel junction

In this work we present for the first time a low-noise submillimeter receiver with a mixer using Superconductor-Insulator-Normal metal-Superconductor (SINS) junctions. Junctions containing a normal metal layer may be free of the Josephson current and of the related perturbations of mixer operation specific for the standard SIS mixers. This SINS mixer quality is important for the application in the multibeam submillimeter receiver. The SINS mixer stability of operation and independence on the magnetic field have been confirmed in our experiment. Minimum SINS receiver noise in the 290 – 330 GHz band is about 135 K when the junction R_NC is about 30. Noise, conversion gain and thermal properties of the SINS mixer have been studied and compared with the SIS mixers. The limit of SINS mixer operation improvement is discussed at the end of the work.     

Characterization of Submillimeter Wave Absorbers from 200–600 GHz

This paper presents measurements of both specular and non-specular scattering from several submillimeter wave absorber materials designed for antenna testing and from low-cost carpet materials. The frequency range is 200–600 GHz in specular scattering, and 300–400 GHz in non-specular scattering measurements. The constructed bistatic test bench allows testing of the full continuous angular range of 0°–90°. The measurement results show large differences in performance of different materials. It is shown that reflectivities below –50 dB over limited angular ranges are possible with a correct alignment of the material. Also, low-cost carpet materials have lower than –15 dB reflectivities in most angles, and may be useful in non-critical parts of the antenna test range. The results can be used to optimise the absorber placement inside an antenna range, concerning both best performance and lowest cost.     

Observation of Frequency Down-Shift in a Submillimeter Wave Gyrotron

Frequency down-shift in the initial stage of CW or long pulse operation of a submillimeter wave gyrotron, Gyrotron FU IV, is observed. The shift occurs in a few minutes after turning on the operation and the amount of the shift attains even 0.1 GHz. The observation results are analyzed on the basis of a simple model for heat conduction in the region of a resonant cavity. The frequency shift is explained consistently by expansion of the cavity.