The obtaining of NiCr2O4 nanoparticles by unconventional synthesis methods

This paper presents a study regarding the obtaining of NiCr₂O₄ by two new unconventional synthesis methods: (i) the first method is based on the formation of Cr(III) and Ni(II) carboxylate-type precursors in the redox reaction between the nitrate ion and 1,3-propanediol. The thermal decomposition of these complex combinations, at ~300 °C, leads to an oxide mixture of Cr₂O_3+x and NiO, with advanced homogeneity, small particles and high reactivity. On heating this mixture at 500 °C, Cr₂O₃ reacts with NiO to form NiCr₂O₄, which was evidenced by FT-IR and X-ray diffractometry (XRD) analysis; (ii) the second method starts from a mechanical mixture of (NH₄)₂Cr₂O₇ and Ni(NO₃)₂·6H₂O. On heating this mixture, a violent decomposition at 240 °C with formation of an oxides mixture (Cr₂O₃ + CrO₃) and NiO takes place. On thermal treatment up to 500 °C, an intermediary phase NiCrO₄ is formed, which by decomposition at ~700 °C leads to NiCr₂O₄, evidenced by FT-IR and XRD analysis. NiCr₂O₄ is formed, in both cases, starting with a temperature higher than 400 °C, when the non-stoichiometric chromium oxide (Cr₂O_3+x ) loses the oxygen excess and turns to stoichiometric chromium oxide (Cr₂O₃), which further reacts with NiO.     

Thermal characterization and compatibility studies of perovskite-type Ba0.5Sr0.5Co0.8Fe0.2O3−δ (BSCF) oxide with Cr2O3 at high temperature

The chemical compatibility of perovskite-type Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3?δ (BSCF) oxides with Cr₂O₃ has been examined between room temperature and 1,100 °C. Differential thermal analysis and thermogravimetric analysis were used to analyze the thermal behavior of BSCF–Cr₂O₃ binary mixtures in all composition ranges (0–100 mass% BSCF). The reaction products were identified by X-ray analysis after heating at 700–1,100 °C. As we expected, it was found that perovskite-type BSCF oxide had a poor chemical compatibility with the Cr₂O₃ oxide. In particular, the decomposition process of the BSCF–Cr₂O₃ binary mixture is quite complex and it starts at about 700–750 °C. The mixtures of BSCF and Cr₂O₃ oxides reacted forming mixed complex oxides based on (Ba/Sr)FeO₃, (Co/Fe)CrO₄, and (Ba/Sr)CrO₄ mixtures.     

New synthesis method for M(II) chromites/silica nanocomposites by thermal decomposition of some precursors formed inside the silica gels

In this article, we present a new method for the obtaining of ZnCr₂O₄ and MgCr₂O₄ embedded in silica matrix. This method consists in the formation of Cr(III), Zn(II) and Cr(III), Mg(II) hydroxycarboxylate/carboxylate compounds, during the redox reaction between the nitrate ion and diol (1,3-propanediol), uniformly dispersed in the pores of hybrid gels. The thermal decomposition of these precursors leads to a mixture of corresponding metal oxides. The gels were synthesized starting from mixtures of Cr(NO₃)₃·9H₂O, Zn(NO₃)₂·6H₂O and Cr(NO₃)₃·9H₂O, Mg(NO₃)₂·6H₂O with tetraethyl orthosilicate and 1,3-propanediol for final compositions 50% ZnCr₂O₄/50% SiO₂ and 50% MgCr₂O₄/50% SiO₂. The obtained gels have been thermally treated at 140?°C, when the redox reaction nitrates-diol took place with formation of the precursors within the xerogels pores. The thermal decomposition of all precursors took place up to 300?°C, with formation of oxides mixtures (Cr₂O_3?+?x and ZnO) and (Cr₂O_3?+?x and MgO), respectively. At 400?°C, Cr₂O_3?+?x turn to Cr₂O₃ which reacts with ZnO forming ZnCr₂O₄/SiO₂. Starting with 400?°C, Cr₂O₃ reacts with MgO to an intermediary phase MgCrO₄, which decomposes with the formation of MgCr₂O₄/SiO₂. The formation of the precursors inside the silica matrix and the evolution of the crystalline phases were studied by thermal analysis, FT-IR spectrometry, XRD, and TEM.     

Preparation of CuCr<Subscript>2</Subscript>O<Subscript>4</Subscript> nanopowders using two different chromium sources

CuCr₂O₄ spinel powders were synthesized starting from different chromium sources, namely (i) chromium oxide (α-Cr₂O₃) and (ii) ammonium dichromate ((NH₄)₂Cr₂O₇). The copper source was a Cu(II) carboxylate-type complex. The Cu(II) carboxylate complex was obtained by the redox reaction between Cu(NO₃)₂·3H₂O and 1,3-propanediol (1,3PG) at 130 °C. In the first case (i), we have started from a mixture of α-Cr₂O₃, Cu(NO₃)₂·3H₂O and 1,3PG that upon heating formed the copper malonate complex, which decomposed around 220 °C forming an oxide mixture (CuO + α-Cr₂O₃). In the second case (ii), (NH₄)₂Cr₂O₇, Cu(NO₃)₂·3H₂O and 1,3PG were homogenously mixed. Heating this mixture at 130 °C resulted, in situ, in the Cu(II) complex. On controlled temperature increase, the violent decomposition of (NH₄)₂Cr₂O₇ took place at 180 °C along with the decomposition of the Cu(II) complex, leading to an amorphous oxide mixture of Cr₂O_3+x and CuO. By annealing the samples in the temperature range 400–1000 °C, the spinel phase (CuCr₂O₄) was obtained in both cases: (i) at 800 °C and (ii) at 600 °C as a result of the interactions between the precursors used, when the oxide system was amorphous and highly reactive. The presence of CuCr₂O₄ was highlighted by XRD and FTIR analyses.     

Thermolysis mechanism of chromium nitrate nonahydrate and computerized modeling of intermediate products

Thermal decomposition of chromium nitrate nonahydrate was studied by thermal analysis, differential scanning calorimetry, infrared spectroscopy, and high temperature X-ray diffraction, so that mass losses were related to the exactly coincident endothermic effects and vibrational energy levels of the evolved gases. The thermal decomposition of chromium nitrate is a complex process, which begins with the simultaneous dehydration and concurrent condensation of 4 mol of the initial monomer Cr(NO₃)₃·9H₂O. Soon after that, the resulting product Cr₄N₁₂O₃₆·31H₂O gradually loses water and azeotrope HNO₃ + H₂O, and is transformed into tetrameric oxynitrate Cr₄N₄O₁₆. At higher temperatures, the tetramer loses N₂O₃ and O₂ and a simultaneous oxidation of Cr(III) to Cr(IV) occurs. The resulting composition at this stage is chromium dioxide dimer Cr₄O₈. Finally, at 447 °C the unstable dimer loses oxygen and is transformed into 2Cr₂O₃. The models of intermediate amorphous compounds represent a reasonably good approximation to the real structures and a proper interpretation of experimental data.     

Studies regarding the formation from metal nitrates and diol of NiM 2 III O4 spinels, inside a silica matrix

The present study deals with preparation and characterization of spinel mixed oxide systems NiM ₂ ^III O₄, where M^III?=?Fe^III, Cr^III. In order to obtain 50% NiFe₂O₄/50% SiO₂ and 50% NiCr₂O₄/50% SiO₂ nanocomposite, we have used a versatile route based on the thermal decomposition inside the SiO₂ matrix, of some particular precursors, coordination compounds of the involved M^II and M^III cations with dicarboxylate ligands. The ligands form in the redox reaction between metal nitrates mixture and 1,3-propanediol at the heating around 140?°C of the gels (tetraethylorthosilicate?Cmetal nitrates?C1,3-propanediol?Cwater). The as-obtained precursors, embedded in silica gels, have been characterized by FT-IR spectrometry and thermal analysis. Both precursors thermally decompose up to 350?°C leading to the formation of the corresponding metal oxides inside the silica matrix. X-ray diffraction of the annealed powders have evidenced the formation of NiFe₂O₄ starting with 600?°C, and NiCr₂O₄ starting with 400?°C. This behavior can be explained by the fact that, by thermal decomposition of the Fe(III) carboxylate at 300?°C, the spinelic phase ??-Fe₂O₃ is formed, which interacts with the NiO, forming the ferrite nuclei. By thermal decomposition of chromium carboxylate, a nonstoichiometric chromium oxide (Cr₂O_3+x ) is formed. In the range 380?C400?°C, Cr₂O_3+x turns into Cr₂O₃ which immediately interacts with NiO leading to the formation of nickel chromites nuclei inside the pores of silica matrix. Both spinels have been obtained as nanocrystalites homogenously dispersed as resulted from XRD and TEM data.     

Anatase–rutile transformation at the synthesis of rutile pigments (Ti,Cr,Nb)O2 and their color properties

Synthesis of rutile pigments is based on solid state reaction and on Hedvall effect, i.e., phase transformation from anatase to rutile. Therefore, it is important to know the thermal behavior of these compounds (the temperature of this change). The goal was to prepare rutile pigments of type Ti_1?3xCr_xNb_2xO_2+x/2 by conventional solid state method from titanium dioxide TiO₂ (AV-01, anatase), to determine an influence of composition (x = 0, 0.05, 0.10, 0.20, 0.30, 0.50) and calcination temperature (850; 900; 950; 1,000; 1,050; 1,100; 1,150 °C) on color properties of these compounds and to analyze other starting compounds of titanium (hydrated anatase paste TiO₂·nH₂O, titanyl sulfate dihydrate TiOSO₄·2H₂O (VKR 611), hydrated sodium titanium oxide paste Na₂Ti₄O₉·nH₂O) and their reaction mixtures for x = 0.05 by simultaneous TG–DTA analysis. According to the highest chroma C of color, the optimal conditions for synthesis of these pigments are concentration x = 0.05 and calcination temperature 1,050 °C and higher. It was observed that initial temperature 760–830 °C is needful for a formation of rutile structure. This temperature is the lowest for hydrated Na₂Ti₄O₉ paste (760 °C) and similar for other starting compounds of titanium.     

The influence of concentration of doping elements on anatase–rutile transformation at the synthesis of rutile pigments (Ti,Cr,Nb)O2 and their pigmentary properties

An analysis of the effects of dopants concentration and different starting titanium compounds on the anatase to rutile phase transformation at the synthesis of rutile pigments Ti_1?3xCr_xNb_2xO_2±δ is presented in this study. The main goal was to analyze reaction mixtures for x = 0.05 (previous study) and 0.30 by simultaneous TG–DTA analysis and to determine the temperature of anatase–rutile transition. For x = 0.05, initial temperatures 760–830 °C are needful for a formation of rutile structure. The temperature is the lowest for the hydrated Na₂Ti₄O₉ paste (760 °C) and similar for other starting compounds of titanium. But for x = 0.30, the anatase–rutile transition begins at higher temperatures 910–1,030 °C because of high-Nb content, which is the inhibitor of this modification change. In addition, we found the influence of calcination temperatures (850, 900, 950, 1000, 1050, 1100, and 1150 °C) on color properties and particle size distribution of these materials prepared from anatase TiO₂ and with x = 0.30. Selected pigments were also analyzed by X-ray powder diffraction.     

Influences of temperature and atmosphere on thermal stability of BaCrO4

In this article, the influences of temperature and atmosphere on thermal stability of BaCrO₄ were investigated. BaCrO₄ powders with an orthorhombic structure were synthesized by a facile aqueous solution route. The synthesized BaCrO₄ products were then heat treated at different atmospheres to evaluate their thermal stability by differential thermal analysis–thermogravimetry (DTA–TG), X-ray photoelectron spectroscopy and X-ray diffraction. BaCrO₄ has a good thermal stability and does not decompose in air up to 1,400 °C. However, the decomposition of BaCrO₄ in vacuum depends mainly upon a two-stage chemical reaction. BaCrO₄ is finally decomposed into BaCr₂O₄ with trivalent Cr³⁺ cations and Ba₃(Cr⁶⁺ Cr⁵⁺)₂O_9?x with both pentavalent Cr⁵⁺ and hexavalent Cr⁶⁺ cations after heat treatments in vacuum.     

Thermal decomposition of the biguanide complexes of the 3d-transition metals

The thermal decomposition (TG, DTG and DTA) of the complexes of biguanide with the following metals was studied: V, Cr, Mn, Co, Ni, Cu and Zn. Structural water, when present, is first eliminated at ～100–150°C; this is followed by a main decomposition state at ～300–350°C. Pyrolytic residues are analysed and characterised by their x-ray powder diffraction patterns and are found to be the oxides V₂O₅, Cr₂O₃, Mn₃O₄, Co₃O₄, NiO, CuO and ZnO, respectively. The decomposition curves of the free ligand (biguanide) and biguanide sulphate are also given. The decomposition characteristics are discussed.     

Thermal behaviour of malonic acid,sodium malonate and its compounds with some bivalent transition metal ions

Characterization, thermal stability and thermal decomposition of transition metal malonates, MCH₂C₂O₄·nH₂O (M = Mn(II), Fe(II), Co(II), Ni(II), Cu(II), Zn(II)), as well as, the thermal behaviour of malonic acid (C₃H₄O₄) and its sodium salt (Na₂CH₂C₂O₄·H₂O) were investigated employing simultaneous thermogravimetry and differential thermal analysis (TG-DTA), differential scanning calorimetry (DSC), infrared spectroscopy, TG-FTIR system, elemental analysis and complexometry. The dehydration, as well as, the thermal decomposition of the anhydrous compounds occurs in a single step. For the sodium malonate the final residue up to 700 °C is sodium carbonate, while the transition metal malonates the final residue up to 335 °C (Mn), 400 °C (Fe), 340 °C (Co), 350 °C (Ni), 520 °C (Cu) and 450 °C (Zn) is Mn₃O₄, Fe₂O₃, Co₃O₄, NiO, CuO and ZnO, respectively. The results also provided information concerning the ligand's denticity, thermal behaviour and identification of some gaseous products evolved during the thermal decomposition of these compounds.     

Thermal processes in the systems with Li-battery cathode materials and LiPF6 -based organic solutions

Thermodynamic instability of positive electrodes (cathodes) in Li-ion batteries in humid air and battery solutions results in capacity fading and batteries degradation, especially at elevated temperatures. In this work, we studied thermal interactions between cathode materials Li₂MnO₃, xLi₂MnO₃ ^.(1???x)Li(MnNiCo)O₂,LiNi_0.33Mn_0.33Co_0.33O₂, LiNi_0.4Mn_0.4Co_0.2O₂, LiNi_0.8Co_0.15Al_0.05O₂ LiMn_1.5Ni_0.5O₄, LiMn(or Fe)PO₄, and battery solutions containing ethylene carbonate (EC) or propylene carbonate (PC), dimethyl carbonate (DMC) or ethylmethyl carbonate (EMC) and LiPF₆ salt in the temperature range of 40–400 °C. It was found that these materials are stable chemically and well performing in LiPF₆-based solutions up to 60 °C. The thermal decomposition of the electrolyte solutions starts >180 °C. The macro-structural transformations of cathode materials upon exothermic reactions were studied by transmission electron microscopy (TEM), X-ray difraction (XRD) and Raman spectroscopy. Differential scanning calorimetry (DSC) studies have shown that the exothermic reactions in the temperature range of 60–140 °C lead to partial decomposition of both the cathode material and electrolyte solution. The systems thus formed consisted of partially decomposed solutions and partially chemically delithiated cathode materials covered by reactions products. Thermal reactions terminate and this system reaches equilibrium at about 120 °C. It remains stable up to the beginning of the solution decomposition at about 180 °C. The increased content of surface Li₂CO₃ is found to significantly affect the thermal processes at high temperature range due to extensive exothermic decomposition at low temperatures.     

Thermal analysis and calorimetry in the study of materials and processes for fundamental sciences and various applications in Central and Eastern Europe

We investigated the influence of B substitution for Al₂W₃O₁₂ on thermal changes of UV–Vis and Raman spectra, and colors. First, B-substituted Al₂W₃O₁₂ powder was synthesized by a solid-state reaction method. Single-phase Al_2?xB_xW₃O₁₂ powders with x = 0, 0.10 and 0.20 were successively prepared. B substitution promoted thermal changes of the UV–Vis spectra, resulting in a more pronounced color change of Al₂W₃O₁₂ in the range of 30–150 °C. Raman spectra of the Al_2?xB_xW₃O₁₂ powders with x = 0 and 0.20 indicated that the lattice vibrations of Al_2?xB_xW₃O₁₂ with x = 0.20 were larger than those of Al₂W₃O₁₂. The thermal change of the color phase (ΔE) in the range 30–150 °C of Al₂W₃O₁₂ was increased by B substitution. The color of the B-substituted Al₂W₃O₁₂ powders changed reversibly from pale white at 30 °C to light yellowish green at 150 °C.     

Thermal stability of the manganese-nickel mixed ferrite and iron phases in the Mn0.5Ni0.5Fe2O4/Fe composite/nanocomposite powder

The composite/nanocomposite powders of Mn_0.5Ni_0.5Fe₂O₄/Fe type were synthesized starting from nanocrystalline Mn_0.5Ni_0.5Fe₂O₄ (D = 7 nm) (obtained by ceramic method and mechanical milling) and commercial Fe powders. The composites, Mn_0.5Ni_0.5Fe₂O₄/Fe, were milled for up to 120 min and subjected to heat treatment at 600 °C and 800 °C for 2 h. The manganese-nickel ferrite/iron composite samples were subjected to differential scanning calorimetry (DSC) up to 900 °C for thermal stability investigations. The composite component phases evolution during mechanical milling and heat treatments were investigated by X-ray diffraction technique. The present phases in Mn_0.5Ni_0.5Fe₂O₄/Fe composite are stable up to 400–450 °C. In the temperature range of 450-600 °C, the interdiffusion phenomena occurs leading to the formation of Fe_1?xMn_xFe₂O₄/Ni–Fe composite type. The new formed ferrite of Fe_1?xMn_xFe₂O₄ type presents an increased lattice parameter as a result of the substitution of nickel cations into the spinel structure by iron ones. Further increases of the temperature lead to the ferrite phase partial reduction and the formation of wustite-FeO type phase. The spinel structure presents incipient recrystallization phenomena after both heat treatments (600 °C and 800 °C). The mean crystallites size of the ferrite after heat treatment at 800 °C is about 75 nm. After DSC treatment at 900 °C, the composite material consists in Fe_1?xMn_xFe₂O₄, Ni structure, FeO, and (NiO)_0.25(MnO)_0.75 phases.     

Thermal behaviour and spectroscopic investigation of some methyl 2-pyridyl ketone complexes

Pyridine derivative complexes are widely employed as biological active materials especially as antibacterial agents. Five transition metal(II) mpk complexes (mpk = methyl 2-pyridyl ketone) were synthesized and investigated using elemental analysis, spectroscopic techniques (IR and UV–Vis–NIR) and conductometric measurements. The general formulae established from experimental data were found to be [M(mpk)₂(NO₃)₂]·xH₂O (x = 0 for M = Cd(II), Zn(II), x = 2 for M = Cu(II)) and [M(mpk)₂(H₂O)₂](NO₃)₂ (M = Co(II), Ni(II)). These compositions were further confirmed by thermal analysis and their thermal stability in dynamic air atmosphere investigated.     

Electrophysical and electrochemical properties of Y1 − x Ca x Cr1 − y Me y O3 (Me = Mg, Cu)

Structure, thermal elongation coefficient, and conductivity of Y_{1 ? x} Ca _x Cr_{1 ? y} Me _y O₃ (Me = Mg, Cu) in air are studied at 100–1000°C. Electrochemical activity of electrodes made of most conducting compositions Y_{1 ? x} Ca _x Cr_{1 ? y} Me _y O₃ (Me = Mg, Cu), contacting solid electrolyte 0.9ZrO₂ + 0.1Y₂O₃, is studied over a wide range of polarizations, in air, at 700–900°C.     

Preparation and characterization of an active catalyst

As an active catalyst to promote thermolysis of ammonium perchlorate (AP), potassium lead hexanitrocobaltate(II) complex (K₂Pb[Co(NO₂)₆]) was synthesized by the direct deposition method and inverse microemulsion method. Its submicron, size, cube morphology, and crystal structure were investigated by SEM, TEM, and XRD analysis, respectively. Thermal decomposition of K₂Pb[Co(NO₂)₆] was studied by the TG/DSC-IR online system and XRD analysis. The catalyst was decomposed at about 300 °C; its gaseous products were NO₂, NO, and N₂O and its solid products were Pb₃O₄, Co₃O₄, PbO, CoO, and KNO₂. Because thermal decomposition of the catalyst was synchronous with low temperature decomposition of AP, thermolysis of AP was promoted remarkably. In particular, the gaseous products (NO _x ) could directly oxidize the absorbed NH₃. As a result, compared to the data of pure AP, the integral heat of AP added 3.0 wt% of the catalyst multiplied by 280 %, the maximum rate of heat release increased by 634 %. The decomposition of catalyzed AP ended at about 317 °C, at which only less than 30 % of pure AP decomposed.     

The thermal properties of the copper(II), nickel(II) and cobalt(II) glycinates

The thermal properties of the Ni(II), Co(II) and Cu(II) complexes of glycine were determined using TG, DTG and DSC techniques. The complexes, MGly₂·nH₂O (n = 1, 2), dehydrated in the temperature range of 75 to 200°C, followed by the decomposition of the anhydrous compounds in the temperature range of 200 to 400°C. The thermal stability of the complexes, as determined by procedural decomposition temperatures, was: Ni(II) >Co(II) >Cu(II).     

Formation of Cr(II) Species in the H2/CrO3 System. Parameter control

The thermal behaviour of CrO₃ on heating up to 600°C in dynamic atmospheres of air, N₂ and H₂ was examined by thermogravimetry (TG), differential thermal analysis (DTA), IR spectroscopy and diffuse reflectance spectroscopy (DRS). The results revealed three major thermal events, depending to different extents on the surrounding atmosphere: (i) melting of CrO₃ near 215°C (independent of the atmosphere), (ii) decomposition into Cr₂(CrO₄)₃ at 340–360°C (insignificantly dependent), and (iii) decomposition of the chromate into Cr₂O₃ at 415–490°C (significantly dependent). The decomposition CrO₃ → Cr₂(CrO₄)₃ is largely thermal and involves exothermic deoxygenation and polymerization reactions, whereas the decomposition Cr₂(CrO₄)₃ → Cr₂O₃ involves endothermic reductive deoxygenation reactions in air (or N₂) which are greatly accelerated and rendered exothermic in the presence of H₂. TG measurements as a function of heating rate (2–50°C min⁻¹) demonstrated the acceleratory role of H₂, which extended to the formation of Cr(II) species. This could sustain a mechanism whereby H₂ molecules are considered to chemisorb dissociatively, and then spillover to induce the reduction. DTA measurements as a function of the heating rate (2–50°C min⁻¹) helped in the derivation of non-isothermal kinetic parameters strongly supportive of the mechanism envisaged. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermal decomposition of sodium chlorate and chromium(III) oxide mixtures

A study of the thermal decomposition of intimate mixtures of sodium chlorate and chromium(III) oxide in different molar ratios was made employing thermogravimetry, differential thermal analysis, chemical analysis, infrared spectroscopy and X-ray diffraction analysis. Sodium chlorate in the presence of chromium(III) oxide starts to decompose around 180°, which is much below the decomposition temperature of pure NaClO₃. Each mole of Cr₂O₃ consumes 8/3 moles of NaClO₃, undergoing oxidation to sodium dichromate.