水溶性AM/AA/AMPS共聚物的高温水解

丙烯酰胺;水溶性AM/AA/AMPS共聚物的高温水解;丙烯酸;甲基丙磺酸;水解反应;反应机制     

粘度和光谱方法研究二元阴离子型丙烯酰胺共聚物(P3A)在不同pH水溶液中的构象变化

采用粘度和光谱方法,研究了强酸性和弱酸性2种阴离子型单体与丙烯酰胺的三元共聚物(P3A)在稀水溶液中pH诱发的构象变化,P3A聚合物由丙烯酰胺(AM)和强酸性离子单体(AMPS)及弱酸性离子单体(AA)组成.试验结果表明P3A聚合物溶液的粘度随pH呈现非单调的增长关系,在pH为4～5范围内产生急剧的升高,这现象归因于聚合物链团从紧密状态向膨胀状态迅速的转变.这两种状态的溶液粘度变化幅度和聚合物P3A中AMPS和AA组合比例紧密相关,芘探针在聚合物P3A溶液中的荧光强度和pH的关系呈现类似粘度变化的结果.在低pH值时,发现单一弱酸离子共聚物(P2AA)溶液发生相分离,然而在含有强酸单元(AMPS)的P3A聚合物情况下,这种现象不再产生.     

AM/AMPS共聚物光化学改性

水溶性高分子AM/AMPS系由丙烯酰胺(AM)和2-丙烯酰胺基-2-甲基丙磺酸(AMPS)组成.本文应用光化学方法对AM/AMPS共聚物进行改性,得到活性可聚合产物.应用这种方法,在高分子链上生成的过氧化物含量随UV光照时间有明显变化,照射5-10 min过氧化物含量最高.值得指出,较高的过氧化物生成量仅在采用二苯酮作为光敏剂和保持低温的条件下才能得到.这种活性改性AM/AMPS共聚物,可用光聚合或热聚合方法引发不同烯类单体共聚合,得到不同用途的接枝/交联共聚物产品.     

全亲水丙烯酰胺/丙烯酸类梳型聚合物的合成及双重响应性聚集行为

以引发剂量的壳聚糖 (CS)为母体骨架,通过与丙烯酰胺 (AM)和丙烯酸 (AA)连续的自由基聚合反应,制备了一种全亲水丙烯酰胺/丙烯酸类梳型聚合物 (CS-PAM/PAA).聚合物中丙烯酰胺和丙烯酸的组成比例可通过控制反应时间调节,并可通过核磁共振碳谱定量计算.该聚合物具有全亲水嵌段共聚物的特性,在水溶液中具有良好的pH响应性和离子响应性.聚合物溶于水并在酸性条件下自组装形成囊泡结构的聚集体,多价金属离子(如Tb³⁺离子)也可以引起聚合物的响应聚集.     

DSC研究高吸水树脂吸水性能与分子结构的关系

以丙烯酸(AA)、丙烯酰胺(AM)和2-丙烯酰胺基-2-甲基丙磺酸(AMPS)为共聚单体合成了聚丙烯酸-丙烯酰胺-2-丙烯酰胺基-2-甲基丙磺酸(PAA-AM-AMPS)三元共聚物高吸水树脂.利用茶叶袋法测定了其最大吸水倍率,通过差示扫描量热仪(DSC)测定并比较了含水量为50%,75%和91%的各种水凝胶的自由水和结合水含量.结果表明在蒸馏水和生理盐水中高吸水树脂的最大吸水倍率分别为1900g/g和185g/g,共聚物的结合水含量随着AMPS和AA含量增加及AM含量的减少而增大;在0.9%生理盐水中,结合水含量随着AMPS和AM含量增加及AA含量的减少而增大,共聚物和均聚物高吸水树脂的最大吸水倍率呈现出与结合水含量相同的变化规律.     

部分水解法制备高分子量水溶性（丙烯酰胺／丙烯酸／2—丙烯酰胺—2—？…

系列的谪分子量水溶性丙烯酰胺／丙烯酸／２－丙烯酰胺－２－甲基丙磺酸（ＡＭ／ＡＡ／ＡＭＰＳ）三元共聚物（Ｐ３Ａ）由相应的（ＡＭ／ＡＭＰＳ０二元共聚物通过部分水解方法制得。聚合物的结构和组成使用电位滴定和＾１３Ｃ－ＮＭＲ谱测定,得到的结果指出,在设定的试验条件下,水解过程中,高分子链上ＡＭＰＳ单元具有充分的稳定性,而丙烯酰胺基平稳地转变为丙烯酸。在所有不同聚合物（Ｐ２Ａ）情况下,由于阴离子基团的ＯＨ＾     

丙烯酰胺/2-丙烯酰胺基十六烷磺酸铵无规共聚物的形态结构研究

本工作应用透射电子显微镜研究了丙烯酰胺/2-丙烯酰胺基十六烷磺酸铵无规共聚物(AM/AMC_(16)SNH_4)的形态结构.给出共聚物在水溶液中具有伸展网状结构,并存在一定程度的疏水基因间的缔合作用.是一种在耐盐性和储存稳定性方面有明显改善的新型改性聚丙烯酰胺.     

水溶性聚合物和两亲聚合物:14.丙烯酰胺/2-丙烯酰胺基十六烷磺酸铵无规共聚物

水溶液中用硫酸亚铁-异丙苯过氧化氢氧化还原引发体系合成了丙烯酰胺(AM)/2-丙烯酰胺基十六烷磺酸铵(AMC_(16)SNH_4)无规共聚物。用元素分析、IR、~(13)C-NMR和~1H-NMR对其进行了表征。对水溶液性质的研究结果表明,与部分水解聚丙烯酰胺相比,这种新型共聚物有着优异的耐盐性、耐温性和贮存稳定性。     

荧光探针法研究疏水改性聚丙烯酰胺溶液的疏水缔合行为

采用胶束共聚 共水解方法合成疏水改性水溶性聚合物聚(丙烯酰胺/丙烯酸钠/N 辛基丙烯酰胺)[P(AM/NaAA/C8AM)],并以芘为荧光探针,应用稳态荧光光谱法研究了它的疏水缔合行为。结果表明,随聚合物浓度、疏水单体摩尔分数、疏水侧链长和温度的增加,疏水缔合作用增强;不同疏水单体含量的P(AM/NaAA/C8AM)的临界缔合浓度为1.5~3.0 g/L;表面活性剂十二烷基硫酸钠(SDS)与P(AM/NaAA/C8AM)发生了强烈的疏水相互作用,形成混合胶束,得到SDS的临界胶束浓度(CMC)为8×10-3 mol/L;由于聚合物链上羧基的存在,使其具有良好的 pH敏感性,随 pH值的增大,P(AM/NaAA/C8AM)的疏水缔合作用呈现先减弱后恒定再增强的变化。     

反相乳液共聚合制备两性丙烯酰胺共聚物的研究

采用Span80-Tween80复合乳化剂和AIBA引发剂,进行丙烯酸钠(NaAA)/丙烯酰胺(AM)/丙烯酰氧基乙基三甲基氯化铵(DAC)反相乳液共聚合.研究了聚合温度、引发剂用量、单体浓度、共聚单体中DAC和AM含量、乳化剂用量及其HLB值、水/油比和水相pH值等聚合反应工艺条件或参数对聚合反应单体转化率和聚合物特性粘度的影响,聚合物特性粘度随引发剂用量和单体浓度的增大而增大的实验结果证实了该两性丙烯酰胺共聚物反相乳液制备过程中凝胶效应的存在.傅立叶红外光谱组成分析表明了两性丙烯酰胺共聚物的成功合成,扫描电镜观测乳胶粒粒径范围在0.6~8.0μm.     

二元阴离子型丙烯酰胺共聚物在二价金属离子存在下相分离行为的研究

水溶性丙烯酰胺类共聚物 ,作为粘度改性剂 ,在工业上已得到广泛应用 .特别近年来 ,它们大量应用于石油工业强化采油技术 ,引起了人们很大的重视[1] .目前 ,这类用途的聚合物 ,主要在聚丙烯酰胺结构中 ,引入阴离子组分和不断增高产物分子量的方法 ,以提高聚合物溶液粘度和增粘效果 ,然而 ,在二价金属离子 (如Ｃａ2 + ,Ｍｇ2 + 等 )存在下 ,羧酸阴离子型丙烯酰胺类共聚物很容易络合发生沉淀 ,从而失去增粘作用[2 ] .同时这类聚合物中酰胺基不稳定 ,易发生水解反应转化为羧酸基 ,并随温度升高而加剧[3 ] ,因此在温度较高的应用条件下 ,二价金属…     

Photocatalytic degradation of poly(acrylamide-co-acrylic acid)

Poly(acrylamide-co-acrylic acid) copolymers of different compositions were synthesized and characterized. The copolymers were statistical with a relatively high percentage of acrylamide units, as determined by (13)C NMR. Reactivity ratios calculated by the Finemann-Ross and Kelen-Tudos methods showed that the copolymers were random with a reactivity ratio of r AM = 3.76 and r AA = 0.28. The photolytic and photocatalytic degradation of the copolymers and the homopolymers was conducted in the presence of combustion-synthesized nano anatase titania. The degradation of the copolymer in the presence of combustion-synthesized titania was significantly higher than that observed in the presence of commercial titania, Degussa P-25. The degradation was modeled by using continuous distribution kinetics by following the time evolution of molecular weight distribution. The degradation follows a two step mechanism, wherein the rapid first step comprises the scission of weak acrylic acid units along the chain which is followed by the breakage of relatively strong acrylamide units. The rate constants for the weak and strong links follow a linear trend with the percentage of acrylic acid and acrylamide in the copolymer, respectively. This linear variation can be correlated with a similar trend observed for the activation energies obtained for the pyrolytic degradation of the polymers.     

Preparation and properties of two-component hydrogels based on 2-acrylamido-2-methylpropane sulphonic acid

Xerogels comprising 2-acrylamido-2-methylpropane sulphonic acid (AMPS) and acrylic acid as well as AMPS and acrylamide crosslinked with hexafunctional crosslinking agent have been prepared by catalytic initiation polymerization to complete conversion. Different percentages of hexafunctional crosslinker, 1,1,1-trimethylolpropane trimethacrylate, were used to prepare crosslinked copolymers having different degree of crosslink densities. The crosslinked copolymers were swollen in water to equilibrium. The volume fraction of polymer, the swelling capacity and the equilibrium water content were obtained. Low conversion polymerization was used to determine the reactivity ratios of both monomer pairs. Fourier transform spectroscopy was utilized to measure the molar ratio of copolymers constituents. © 1998 John Wiley & Sons, Ltd.     

Chromatographic determination of residual monomers in starch-g-polyacrylonitrile and starch-g-polyacrylate

Summary A reverse-phase HPLC method for simultaneous determination of acrylonitrile (AN), acrylamide (AM) and acrylic acid (AC) was developed. The residual monomer AC was quantified in several industrial polymers as well as grafted copolymers. Products of biodegradation of these copolymers were also identified.     

疏水缔合(丙烯酰胺十六烷基二甲基烯丙基氯化铵-2-丙烯酰胺基-2-甲基丙磺酸)三元共聚物的合成与性能研究

疏水缔合水溶性聚合物是指在聚合物亲水性大分子链上引入少量疏水基团的一类水溶性聚合物[1～5].在水溶液中,疏水基团之间由于憎水作用而发生聚集,使大分子链产生分子内与分子之间缔合.在临界缔合浓度以上,以分子间缔合为主,增大了流体力学体积,因此,具有较好的增粘作用.疏水基的加入可大幅度地改变聚合物的流变性能.在聚合物驱油中的流度控制,提高波及效率、以及调剖中起到非常重要的作用.     

Thermal properties of copolymers of 2‐Acrylamido‐2‐methylpropanesulphonic acid with some vinyl monomers

2‐Acrylamido‐2‐methylpropanesulphonic acid (AMPS) was copolymerized with both acrylic acid (AA) and vinyl acetate (VA) at different compositions. The thermal behaviors of the resulted copolymers, PAMPS, PAA and PVA were studied using thermogravimetric analyses. In all cases of homopolymers and copolymers, there are two degradation stages. The observed enhancement of the thermal properties of the copolymers compared with that of PAMPS are attributed to intramolecular cyclization reactions and ring formations. The apparent activation energies of the decomposition were determined and correlated to the sequence of the thermal stabilities of the various polymers.     

RADICAL GRAFTING REACTIONS ONTO STARCH AND OTHER WATER-SOLUBLE COPOLYMERS IN ISOLATED GEL DROPLETS

A novel radical grafting copolymerization process has been designed for water-soluble polymers which avoids the problems of conducting grafting reactions in highly viscous polymerization media. A variety of water-soluble graft copolymers having starch or dextran as the backbone chain with grafted side chains of polyacrylamide (—AM—), poly (acrylic acid ) (—AA—), poly (acrylamide-co-acrylic acid) (—AM—NH_4AA—) or poly ( acrylamide-co-2-acryiamido-2-methyl-l-propanesulphinic acid) (—AM—AMPS—) have been synthesized in gel droplets using aceric sulphate redox initiator, and their properties compared. The reaction conditions were optimized taking into account reaction kinetic data and the observed properties of the products produced under different reaction conditions. The effects of the ratios of [backbone]/[graft monomer], [ AM]/[ AA]/[AMPS] , [Ce~(4+)]/[ S_2O_8=] and pH value on the reaction rate , conversion, grafting degree, grafted chain length and the product molecular weight have been investigated.