受激布里渊散射光脉冲波形的研究

从实验和理论上研究了受激布里渊散射(SBS)光脉冲波形.在Nd∶YAG调Q激光器中实验研究了SBS光脉冲波形随抽运光参数、结构参数和介质参数的变化规律，并利用SBS理论模型进行了数值模拟，实验与数值模拟结果的变化趋势基本一致.结果表明，抽运光能量越小，透镜焦距越短，镜-池间距越长，介质声子寿命越长，SBS光脉冲波形就越不容易出现调制现象.分析和讨论了抽运光参数、结构参数和介质参数对SBS光脉冲波形的影响机理. 关键词： 受激布里渊散射 脉冲波形 抽运光参数 结构参数     

受激布里渊散射光限幅输出波形控制研究

数值模拟了种子场诱导受激布里渊散射光限幅过程的限幅输出波形特性.得到利用种子场控制限幅脉冲波形的规律：选取种子场脉冲宽度为抽运脉冲宽度的五倍，抽运脉冲相对于种子脉冲的延迟时间控制在与抽运脉冲宽度相当时，限幅输出波形最佳.限幅输出波形同时受抽运光功率影响，随抽运能量的增加，限幅脉冲功率不断下降，直至趋于0. 关键词： 受激布里渊散射 限幅输出波形 注入种子     

透镜焦距对受激布里渊散射光限幅特性的影响

采用受激布里渊散射(SBS)噪声起源理论模型，数值模拟了透镜焦距对SBS光限幅功率特性和能量特性的影响.结果表明，改变透镜焦距就可以方便的控制SBS光限幅的功率波形和输出能量.当采用焦距适中的透镜(f=15cm)时，可以得到较低的限幅输出能量；当采用短焦距的透镜(f=5cm)时，可以得到较理想的限幅功率波形.在实验上将波长1064nm、脉宽8ns、能量16mJ的Nd:YAG激光脉冲聚焦到CCl₄介质中，研究了限幅功率波形和限幅输出能量随透镜焦距的变化规律，实验结果与理论模拟相符合. 关键词： 受激布里渊散射 光限幅 数值模拟     

布里渊增强四波混频时域特性的理论研究

通过对布里渊增强四波混频(BEFWM)瞬态耦合波方程的数值求解，描述了共轭输出光的时域调制行为.同时，对能量耦合过程中起决定性作用的声学波的时空演化特征进行了模拟与分析，由此给出BEFWM时域特性物理机理的解释.研究表明，共轭光输出强度的波动与介质内声波场的分布和起伏相关联，共轭光波形调制现象的强弱取决于介质声子寿命、信号及抽运光强度、有效作用长度等诸多参数.     

受激布里渊散射介质CCl4中脉冲传输与功率限幅特性

分析了受激布里渊散射介质CCl4对纳秒激光脉冲的传输特性及功率限幅特性. 结果表明：透射脉冲波形随抽运光能量增加而压缩变形，脉冲前沿保持高斯型，后沿被压缩成功率“平台”，功率“平台”随抽运脉冲能量增加而逐渐变宽，但功率水平不变，表明该光学系统具有的功率限幅特性. 详细分析了功率限幅特性随抽运能量的变化规律和时间响应特性规律，采用脉宽为10ns、波长为1.06μm的Nd:YAG激光脉冲进行实验验证，理论与实验结论相符合.  关键词： 受激布里渊散射 功率限幅     

抽运能量对受激布里渊散射光限幅特性的影响

采用布里渊噪声起源模型,数值模拟了受激布里渊散射介质CCl4对波长1064nm的Nd：YAG纳秒激光脉冲的传输特性及光限幅特性。入射抽运脉冲能量较低时,非线性介质对纳秒激光脉冲呈光学透明。入射抽运脉冲能量高于受激布里渊散射产生阈值后,透射脉冲峰值受限,脉宽压缩,能量趋于饱和,说明该光学系统同时具有光功率限幅和能量限幅的光限幅特性。利用理论模型模拟了如下光限幅参量：透射脉冲峰值功率、透射能量、能量透射率、脉宽压缩率依赖抽运光能量的变化关系。相应的理论模拟计算结果由实验进行验证,实验结果与理论模拟相符合。     

受激布里渊散射对纳秒激光脉冲光限幅规律

 研究了受激布里渊散射对纳秒激光脉冲的光限幅效应。针对四氯化碳介质研究了受激布里渊散射对2ns激光脉冲的光限幅和稳定输出能量的特性,给出了光限幅特性及输出能量与光限幅介质的结构参数之间的关系。对于输入能量波动范围在 13%的激光脉冲,实验获得输出能量波动范围为 7%,与理论分析的结果基本符合。     

受激布里渊散射对纳秒激光脉冲光限幅规律

研究了受激布里渊散射对纳秒激光脉冲的光限幅效应。针对四氯化碳介质研究了受激布里渊散射对2ns激光脉冲的光限幅和稳定输出能量的特性,给出了光限幅特性及输出能量与光限幅介质的结构参数之间的关系。对于输入能量波动范围在 13%的激光脉冲,实验获得输出能量波动范围为 7%,与理论分析的结果基本符合。     

选用混合介质优化介质和控制受激布里渊散射特性的研究

本文提出了选用混合介质优化介质和控制其SBS特性的方案.分析了全氟碳化合物系列液体介质具有良好互溶性的缘故,数值模拟了HT-230/FC-72混合介质的增益系数、声子寿命和布里渊频移随混合比的变化曲线.在Countinuum Nd:YAG种子注入激光系统中测定了HT-230/FC-72混合介质的吸收系数和光学击穿阈值随混合比的变化,并实验研究了混合介质的能量反射率和Stokes光脉冲波形随混合比的变化.通过选用混合介质不仅优化介质,而且在一定范围之内可控制其SBS特性. 关键词： 受激布里渊散射 混合介质 优化介质 控制SBS特性     

受激布里渊散射介质CCl_4中脉冲传输与功率限幅特性

分析了受激布里渊散射介质CCl4 对纳秒激光脉冲的传输特性及功率限幅特性 .结果表明 :透射脉冲波形随抽运光能量增加而压缩变形 ,脉冲前沿保持高斯型 ,后沿被压缩成功率“平台” ,功率“平台”随抽运脉冲能量增加而逐渐变宽 ,但功率水平不变 ,表明该光学系统具有的功率限幅特性 .详细分析了功率限幅特性随抽运能量的变化规律和时间响应特性规律 ,采用脉宽为 10ns、波长为 1 0 6 μm的Nd :YAG激光脉冲进行实验验证 ,理论与实验结论相符合 .     

Effect of water temperature on pulse duration and energy of stimulated Brillouin scattering

The water temperature has a strong effect on the kinematic viscosity, which is inversely proportional to the phonon lifetime and the gain coefficient. The higher the temperature is, the smaller the kinematic viscosity is, and the larger the phonon lifetime is. At a low pump power and a short focal length, we can derive a single-peak stimulated Brillouin scattering (SBS) pulse. The duration of this single-peak SBS pulse depends mainly on the phonon lifetime of water. With the increase of the water temperature, the duration of such a single-peak SBS pulse will become longer, and the SBS energy will become higher for the gain coefficient, which is related to the phonon lifetime. Therefore, varying the medium temperature can lead to the changes of SBS pulse duration and SBS energy.     

Investigation on the output energy characteristic of optical limiting based on stimulated Brillouin scattering

Stimulated Brillouin scattering (SBS) featuring sub-nanosecond response time takes place at a high power threshold, which enables its application at a high power density. When the intensity of input light excesses the SBS threshold, strong SBS process takes place through SBS medium, leading to a quick energy transfer from pump to the Stokes and thereby an optical limiting characteristic in the output energy. In this paper, the correlation between SBS output energy and input power density is numerically simulated and validated in the Nd: YAG Q-switch laser system. The results indicate that not only the output energy exhibits an optical limiting characteristic, but also the clamped value of output energy can be controlled by changing the medium or the focal length.     

基于光纤中SBS相位共轭的自调Q光纤激光器

分析了利用光纤中的受激布里渊散射(stimulated Brillouin scattering,SBS)相位共轭效应进行激光腔内调Q,产生ns量级脉冲激光的原理,并对利用该效应产生的激光脉冲波形和脉冲形成过程进行了数值模拟,得到的脉冲波形与SBS相位共轭反射率随时间变化曲线基本一致,表明利用光纤中的SBS相位共轭作用调Q具有可行性.据此,对采用单模光纤(single-mode fiber,SMF)作为SBS池的Er³⁺掺杂调Q光纤激光器进行实验研究.当单模光纤长度为1.5 m时,在45 mW的光抽运功率下得到脉宽约2.6ns,脉冲周期58.23ns,平均功率7.35mW的激光脉冲.进一步的研究表明:激光器中相位共轭镜的形成与SBS介质长度有关,SBS介质过长,斯托克斯线之间无固定的相位关系,不能形成相干叠加,SBS相位共轭腔不能形成;SBS介质过短,腔内正交偏振模光子寿命的改变使脉冲出现双峰现象.脉冲形成后其属性只与SBS动态属性有关.     

受激布里渊散射脉冲压缩技术研究进展

受激布里渊散射（SBS）作为三阶光学效应广泛应用于激光组束、分布式光纤传感、布里渊激光器等领域。近年来,SBS脉冲压缩亦得到特殊关注。基于布里渊放大过程中的能量转移特性,SBS脉冲压缩技术能够将ns量级脉冲压缩至亚ns量级,峰值功率可提升1～2个数量级。系统介绍了SBS脉冲压缩基本理论,综合论述了SBS压缩器结构、增益介质、泵浦脉冲等因素对脉冲压缩特性的影响,并对SBS脉冲压缩发展趋势进行了展望,为今后SBS特性的研究提供了有益参考,也为高重频、高能量激光的获取提供了可行方案。

     

Influence of medium parameters on power limiting characteristic in stimulated Brillouin scattering process

By adopting noise initiation model of stimulated Brillouin scattering (SBS), the influence of phonon lifetime and gain coefficient of medium on power limiting characteristic is numerically investigated. Through using actual parameters of three media, CCl4, acetone, and CS2, the waveforms of transmitted pulses are simulated. The result shows that different media have little effect on the front peak of waveform,while have an obvious effect on the height of power limiting platform. When the medium which has short phonon lifetime and small gain coefficient is used, the height of power limiting platform is comparatively high. In experiment, by focusing 1064-nm, 8-ns, 18-mJ pulses into these three media, the waveforms of transmitted pulses are obtained. The experimental results are in good agreement with conclusions of theoretical simulations.     

Optical limiting effect based on stimulated Brillouin scattering in CCl4

The optical limiting effect based on stimulated Brillouin scattering (SBS) in a nonlinear medium was investigated. We numerically treated the nonlinear propagation process with a theoretical model, which includes the spontaneous nature of the initiation of SBS, and obtained optical limiting effect in the process. Energy limiting, pulse reshaping and stabilization have been demonstrated on SBS mechanism with the nonlinear medium CCl_4. The input optical signals were Nd:YAG nanosecond laser pulses with width varying from 16ns to 7ns then to 2ns, the relationship between the transmitted signal and launched pump signal was shown. In the experimental regime, the most stable pulse and a superior energy stabilization of the transmitted pulse were obtained when the laser pulse-width became as short as 2ns. For the energy variation of laser pulses in a wide range of 14－88mJ, the output energy was limited in a quite narrow range 4.5－5.5mJ.