Investigation of ion transport in Li<Subscript>8</Subscript>ZrO<Subscript>6</Subscript> and Li<Subscript>6</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> solid electrolytes

Lithium ionic conductivity and spin-lattice relaxation rates were measured in Li₈ZrO₆ and Li₆Zr₂O₇ solid electrolytes. It was found that the Li₈ZrO₆ solid electrolyte undergoes a transition to the superionic state in the temperature range 673–703 K. It was shown that Li⁺ ions are mobile in particular lattice positions of the Li₆Zr₂O₇ phase, and that ionic conductivity is monotonic at an activation energy of 79.4 kJ/mol.     

Microstructural and Radioluminescence Characteristics of Nd<Superscript>3+</Superscript> Doped Columbite-Type SrNb<Subscript>2</Subscript>O<Subscript>6</Subscript> Phosphor

Undoped and different concentration Nd³⁺ doped SrNb₂O₆ powders with columbite structure were synthesized by molten salt process using a mixture of strontium nitrate and niobium (V) oxide and NaCl-KCl salt mixture as a flux under relatively low calcining temperature. X-ray diffraction analysis results indicated that SrNb₂O₆ phases found to be orthorhombic columbite single phase for undoped, 0.5 and 3 mol% Nd³⁺ doping concentrations. Phase composition of the powders was examined by SEM-EDS analyses. Radioluminescence properties of Nd³⁺ doped samples from UV to near-IR spectral region were studied. The emissions increased with the doping concentration of up to 3 mol%, and then decreased due to concentration quenching effect. There is a sharp emission peak around 880 nm associated with ⁴F_5/2 → ⁴I_9/2 transition in the Nd³⁺ ion between 300 and 1100 nm. The broad emission band intensity was observed from 400 to 650 nm where the peak intensities increased by increasing Nd³⁺ doping concentration. All the measurements were taken under the room temperature.     

Influence of Bi<Superscript>3+</Superscript> ions on low temperature D.C. conductivity of Na<Subscript>2</Subscript>SiCuO<Subscript>4</Subscript> glasses

Sodium silicate glasses doped with CuO and mixed with different contents of Bi₂O₃ (ranging from 4 to 16 mol%) were prepared. D.C. conductivity studies over a range of temperature from 225 to 325 K have been carried out. The conductivity is observed to decrease linearly with increase of Bi₂O₃ concentration. The results are analyzed using optical absorption, ESR, and IR spectral data. The spectroscopic studies have indicated that there is a gradual reduction divalent copper ions to monovalent ions with increase of Bi₂O₃ concentration. These studies have also indicated that such Cu⁺ ions participate in the glasses network forming and increase the polymerization of the glass network. The analysis of the results of D.C. conductivity indicated that in temperature region T > θ _D/2, the small polaron hoping model is valid, and the conduction is predicted to be adiabatic type. The analysis of the results has further revealed that there is a gradual change over of conduction mechanism from ionic to electronic with increase of Bi₂O₃ concentration. The low temperature part of D.C. conductivity is explained using variable range hopping (VRH) model.     

Grain size effects on dynamics of Li-ions in Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> glass-ceramic nanocomposites

Li₃V₂(PO₄)₃ glass-ceramic nanocomposites, based on 37.5Li₂O-25V₂O₅-37.5P₂O₅ mol% glass, were successfully prepared via heat treatment (HT) process. The structure and morphology were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM). XRD patterns exhibit the formation of Li₃V₂(PO₄)₃ NASICON type with monoclinic structure. The grain sizes were found to be in the range 32–56 nm. The effect of grain size on the dynamics of Li⁺ ions in these glass-ceramic nanocomposites has been studied in the frequency range of 20 Hz–1 MHz and in the temperature range of 333–373 K and analyzed by using both the conductivity and modulus formalisms. The frequency exponent obtained from the power law decreases with the increase of temperature, suggesting a weaker correlation among the Li⁺ ions. Scaling of the conductivity spectra has also been performed in order to obtain insight into the relaxation mechanisms. The imaginary modulus spectra are broader than the Debye peak-width, but are asymmetric and distorted toward the high frequency region of the maxima. The electric modulus data have been fitted to the non-exponential Kohlrausch–Williams–Watts (KWW) function and the value of the stretched exponent β is fairly low, suggesting a higher ionic conductivity in the glass and its glass-ceramic nanocomposites. The advantages of these glass-ceramic nanocomposites as cathode materials in Li-ion batteries are shortened diffusion paths for Li⁺ ions/electrons and higher surface area of contact between cathode and electrolyte.     

Mixed (ionic and hole) conductivity of Tl<Subscript>3</Subscript>VS<Subscript>4</Subscript> crystals

A model of mixed (ionic and hole) conductivity in Tl₃VS₄ crystals at close-to-room temperatures is proposed. The significant fraction of the ionic conductivity component (～70% of the total conductivity) is explained by the nonstoichiometric electrically active thallium vacancies, whose acceptor levels provide p-type conductivity. The characteristic time dependence of the voltage developing across a sample due to its polarization and depolarization is described using the diffusion theory of mixed conductivity previously developed by Yokota. The charge transport phenomena in Tl₃VS₄ are studied experimentally, and the data are processed according to the theoretical model.     

Solid polymeric electrolyte of PVC–ENR–LiClO<Subscript>4</Subscript>

The ionic conductivity of PVC–ENR–LiClO₄ (PVC, polyvinyl chloride; ENR, epoxidized natural rubber) as a function of LiClO₄ concentration, ENR concentration, temperature, and radiation dose of electron beam cross-linking has been studied. The electrolyte samples were prepared by solution casting technique. Their ionic conductivities were measured using the impedance spectroscopy technique. It was observed that the relationship between the concentration of salt, as well as temperature, and conductivity were linear. The electrolyte conductivity increases with ENR concentration. This relationship was discussed using the number of charge carrier theory. The conductivity–temperature behaviour of the electrolyte is Arrhenian. The conductivity also varies with the radiation dose of the electron beam cross-linking. The highest room temperature conductivity of the electrolyte of 8.5 × 10⁻⁷ S/cm was obtained at 30% by weight of LiClO₄. The activation energy, E _a and pre-exponential factor, σ _o, are 1.4 × 10⁻² eV and 1.5 × 10⁻¹¹ S/cm, respectively.     

Effect of sintering conditions on the properties of sol-gel-derived Li<Subscript>1.3</Subscript>Al<Subscript>0.3</Subscript>Ti<Subscript>1.7</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

Solid electrolyte Li_1.3Al_0.3Ti_1.7(PO₄)₃ was prepared by sol-gel method under different sintering conditions. The structural identification, surface morphology, electrochemical window, ionic conductivity, and activation energy of the Li_1.3Al_0.3Ti_1.7(PO₄)₃ sintered pellets were investigated by X-ray diffraction, scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. It is found that the sintering temperature and time have considerable effect on the properties of the Li_1.3Al_0.3Ti_1.7(PO₄)₃ sintered pellets. The Li_1.3Al_0.3Ti_1.7(PO₄)₃ pellet sintered at 900 °C for 2 h is denser than the pellets sintered at other conditions. Different sintering conditions result in the sintered pellet with different porosity. However, the sintering conditions have little effect on the electrochemical window of Li_1.3Al_0.3Ti_1.7(PO₄)₃. Among the Li_1.3Al_0.3Ti_1.7(PO₄)₃ pellets sintered at various conditions, the pellet sintered at 900 °C for 2 h shows the highest ionic conductivity of 3.46 × 10⁻⁴ S cm⁻¹ and the lowest activation energy of 0.2821 eV.     

Incorporation of NH<Subscript>4</Subscript>NO<Subscript>3</Subscript> into MC-PVA blend-based polymer to prepare proton-conducting polymer electrolyte films

Proton-conducting solid polymer blend electrolytes based on methylcellulose-polyvinyl alcohol:ammonium nitrate (MC-PVA:NH₄NO₃) were prepared by the solution cast technique. The structural and electrical properties of the samples were examined by X-ray diffraction (XRD), Fourier transform infrared (FTIR), and electrical impedance (EI) spectroscopy. The shifting and change in the intensity of FTIR bands of the electrolyte samples confirm the complex formation between the MC-PVA polymer blend and the NH₄NO₃ added salt. The observed broadening in the XRD pattern of the doped samples reveals the increase of the amorphous fraction of polymer electrolyte samples. The increase in electrical conductivity of polymer electrolyte samples with increasing salt concentration attributed to the formation of charge-transfer complexes, and to increase in the amorphous domains. A maximum ionic conductivity of about 7.39 × 10^?5 S cm^?1 was achieved at room temperature for the sample incorporating 20 wt% of NH₄NO₃. The DC conductivity of the present polymer system exhibits Arrhenius-type dependence with temperature. The decrease in the values of activation energies with increasing salt concentration indicates the ease mobility of ions. The decrease in dielectric constant with increasing frequency was observed at all temperatures. Optical properties such as absorption edge, optical band gap, and tail of localized state were estimated for polymer blend and their electrolyte films. It was found that the optical band gap values shifted towards lower photon energy from 6.06 to 4.75 eV by altering the NH₄NO₃ salt content.     

Effects of MnO<Subscript>2</Subscript> nano-particles on the conductivity of PMMA-PEO-LiClO<Subscript>4</Subscript>-EC polymer electrolytes

Li-ion rechargeable batteries based on polymer electrolytes are of great interest for solid state electrochemical devices nowadays. Many studies have been carried out to improve the ionic conductivity of polymer electrolytes, which include polymer blending, incorporating plasticizers and filler additives in the electrolyte systems. This paper describes the effects of incorporating nano-sized MnO₂ filler on the ionic conductivity enhancement of a plasticized polymer blend PMMA–PEO–LiClO₄–EC electrolyte system. The maximum conductivity achieved is within the range of 10⁻³ S cm⁻¹ by optimizing the composition of the polymers, salts, plasticizer, and filler. The temperature dependence of the polymer conductivity obeys the VTF relationship. DSC and XRD studies are carried out to clarify the complex formation between the polymers, salts, and plasticizer.     

Structural and Near-Infrared Properties of Nd<Superscript>3+</Superscript> Activated Lu<Subscript>3</Subscript>NbO<Subscript>7</Subscript> Phosphor

Undoped and Nd³⁺ doped lutetium niobate phases have been prepared by a conventional solid state reaction method using lutetium acetate and niobium oxide at 1250 °C for 6 h. X-ray diffraction patterns of the 6 mol% Lu₃NbO₇ sample exhibited a cubic fluorite single phase. Phase structure exhibited interesting crystallization behaviour depending on increasing Nd³⁺ concentration which led to a Lu₃NbO₇ single phase formation during the heat treatment process. SEM investigations were also in agreement with the XRD results. Morphologies of Nd³⁺ doped lutetium niobate powders exhibited oval like shapes and grain sizes varied between 0.3 and 5 μm. Near-infrared luminescence properties of Nd³⁺ doped Lu₃NbO₇ were also studied. 1.06 μm laser transition characteristics of Nd³⁺ doped lutetium niobate have been observed. Concentration quenching phenomenon was not detected depending on increasing Nd³⁺ doping concentrations at room temperature.     

Electron paramagnetic resonance of Yb<Superscript>3+</Superscript> ions in a concentrated YbRh<Subscript>2</Subscript>Si<Subscript>2</Subscript> compound with heavy fermions

The EPR signal from localized ytterbium ions was observed in an undoped YbRh₂Si₂ compound with heavy fermions in the temperature range from 1.5 to 25 K. The exponential contribution dominating the temperature dependence of EPR line width at temperatures above 15 K was shown to be caused by the random transitions from the ground to the first excited Stark sublevel of the Yb³⁺(4f¹³) ion with the activation energy Δ=115 K.     

Structural,thermal and ion transport studies on nanocomposite polymer electrolyte-{(PEO + SiO<Subscript>2</Subscript>):NH<Subscript>4</Subscript>SCN} system

Development and characterisation of polyethylene oxide (PEO)-based nanocomposite polymer electrolytes comprising of (PEO-SiO₂): NH₄SCN is reported. For synthesis of the said electrolyte, polyethylene oxide has been taken as polymer host and NH₄SCN as an ionic charge supplier. Sol–gel-derived silica powder of nano dimension has been used as ceramic filler for development of nanocomposite electrolytes. The maximum conductivity of electrolyte ∼2.0 × 10⁻⁶ S/cm is observed for samples containing 30 wt.% silica. The temperature dependence of conductivity seems to follow an Arrhenius-type, thermally activated process over a limited temperature range.     

Conductivity and spectroscopic studies of Li<Subscript>2</Subscript>O-V<Subscript>2</Subscript>O<Subscript>5</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

Lithium vanadium-borate glasses with the composition of 0.3Li₂O–(0.7-x)B₂O₃–xV₂O₅ (x?=?0.3, 0.325, 0.35, 0.375, 0.4, 0.425, 0.45, and 0.475) were prepared by melt-quenching method. According to differential scanning calorimetry data, vanadium oxide acts as both glass former and glass modifier, since the thermal stability of glasses decreases with an increase in V₂O₅ concentration. Fourier transform infrared spectroscopy data show that the vibrations of [VO₄] structural units occur at V₂O₅ concentration of 45 mol%. It is established that the concentration of V⁴⁺ ions increases exponentially with the growth of vanadium oxide concentration. Direct and alternative current measurements are carried out to estimate the contribution both electronic and ionic conductivities to the value of total conductivity. It is shown that the electronic conductivity is predominant in the total one. The glass having the composition of 0.3Li₂O-0.275B₂O₃-0.475V₂O₅ shows the highest electrical conductivity that has the value of 7.4?×?10^?5 S cm^?1 at room temperature.     

Nano Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> as sulfur host for high-performance Li-S battery

S/Li₄Ti₅O₁₂ cathode with high lithium ionic conductivity was prepared for Li-S battery. Herein, nano Li₄Ti₅O₁₂ is used as sulfur host and fast Li⁺ conductor, which can adsorb effectively polysulfides and improve remarkably Li⁺ diffusion coefficient in sulfur cathode. At 0.5 C, S/Li₄Ti₅O₁₂ cathode has a stable discharge capacity of 616 mAh g^?1 at the 700th cycle and a capacity loss per cycle of 0.0196% from the second to the 700th cycle, but the corresponding values of S/C cathode are 437 mAh g^?1 and 0.0598%. Even at 2 C, the capacity loss per cycle of S/Li₄Ti₅O₁₂ cathode is only 0.0273% from the second to the 700th cycle. The results indicate that Li₄Ti₅O₁₂ as the sulfur host plays a key role on the high performance of Li-S battery due to reducing the shuttle effect and enhancing lithium ionic conductivity.     

Growth and spectral properties of self-frequency doubling crystal,Nd:Ca<Subscript>9.03</Subscript>Na<Subscript>1.08</Subscript>La<Subscript>0.62</Subscript>(VO<Subscript>4</Subscript>)<Subscript>7</Subscript>

The non-doped and doped Nd³⁺ of Ca_9.03Na_1.08La_0.62(VO₄)₇ crystals were grown by the Czochralski technique. The effective segregation coefficients of Na⁺ and Nd³⁺ ions in the crystal were measured to be about 0.5 and 1.1, respectively. The XPS analysis of Ca_9.03Na_1.08La_0.62(VO₄)₇ crystal indicates that the vanadium in the crystal is a mixture of V⁴⁺ (1.46 at. %) and V⁵⁺ (98.54 at. %). The hardness of Nd:Ca_9.03Na_1.08La_0.62(VO₄)₇ crystal is about 383.1 VDH. Nd:Ca_9.03Na_1.08La_0.62(VO₄)₇ crystal exhibits similar thermal expansion coefficients along the a (11.2×10^-6 K^-1) and c (13.7×10^-6 K^-1) axes, indicating a low thermal expansion anisotropy (α_c/α_a≈1.2). The qualitative frequency-doubling experiment shows that the doping of Na⁺ ion can help reduce the scattering of frequency-doubling light, and the intensity of SHG for Ca_9.03Na_1.08La_0.62(VO₄)₇ crystal is found to be about 3.5 times as large as that of KDP. The polarized absorption and fluorescence spectra are analyzed based on Judd–Ofelt theory, which exhibits that the π-polarized absorption and stimulated emission cross sections are 6.07×10^-20 cm² with an FWHM 12.0 nm at 810 nm and 1.42×10^-19 cm² at 1069 nm, respectively. The fluorescence lifetime is 115 μs at room temperature. All the results indicate that Nd:Ca_9.03Na_1.08La_0.62(VO₄)₇ crystal is a candidate of self-frequency doubling laser material. PACS 42.62.Fi; 42.70.Mp; 81.10.Fq     

Electrical characterization of the [N(CH<Subscript>3</Subscript>)<Subscript>4</Subscript>][N(C<Subscript>2</Subscript>H<Subscript>5</Subscript>)<Subscript>4</Subscript>]ZnCl<Subscript>4</Subscript> compound

The [N(CH₃)₄][N(C₂H₅)₄]ZnCl₄ compound has been synthesized by a solution-based chemical method. The X-ray diffraction study at room temperature revealed an orthorhombic system with P2₁2₁2 space group. The complex impedance has been investigated in the temperature and frequency ranges 420–520 K and 200 Hz–5 MHz, respectively. The grain interior and grain boundary contribution to the electrical response in the material have been identified. Dielectric data were analyzed using the complex electrical modulus M ^* for the sample at various temperature. The modulus plots can be characterized by full width at half height or in terms of a non-exponential decay function ϕ(t) = exp[(−t/τ) ^β ]. The detailed conductivity study indicated that the electrical conduction in the material is a thermally activated process. The variation of the AC conductivity with frequency at different temperatures obeys the Almond and West universal law.     

Structural and electrical properties of KCa<Subscript>2</Subscript>Nb<Subscript>5</Subscript>O<Subscript>15</Subscript> ceramics

A polycrystalline sample of KCa₂Nb₅O₁₅ with tungsten bronze structure was prepared by a mixed oxide method at high temperature. A preliminary structural analysis of the compound showed an orthorhombic crystal structure at room temperature. Surface morphology of the compound shows a uniform grain distribution throughout the surface of the sample. Studies of temperature variation on dielectric response at various frequencies show that the compound has a transition temperature well above the room temperature (i.e., 105°C), which was confirmed by the polarization measurement. Electrical properties of the material have been studied using a complex impedance spectroscopy (CIS) technique in a wide temperature (31–500°C) and frequency (10²–10⁶ Hz) range that showed only bulk contribution and non-Debye type relaxation processes in the material. The activation energy of the compound (calculated from both the loss and modulus spectrum) is same, and hence the relaxation process may be attributed to the same type of charge carriers. A possible ‘hopping’ mechanism for electrical transport processes in the system is evident from the modulus analysis. A plot of dc conductivity (bulk) with temperature variation demonstrates that the compound exhibits Arrhenius type of electrical conductivity.      

Structure,thermal properties,conductivity and electrochemical stability of di-urethanesil hybrids doped with LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>

Variable chain length di-urethane cross-linked poly(oxyethylene) (POE)/siloxane hybrid networks were prepared by application of a sol-gel strategy. These materials, designated as di-urethanesils (represented as d-Ut(Y′), where Y′ indicates the average molecular weight of the polymer segment), were doped with lithium triflate (LiCF₃SO₃). The two host hybrid matrices used, d-Ut(300) and d-Ut(600), incorporate POE chains with approximately 6 and 13 (OCH₂CH₂) repeat units, respectively. All the samples studied, with compositions ∞ > n ≥ 1 (where n is the molar ratio of (OCH₂CH₂) repeat units per Li⁺), are entirely amorphous. The di-urethanesils are thermally stable up to at least 200 °C. At room temperature the conductivity maxima of the d-Ut(300)- and d-Ut(600)-based di-urethanesil families are located at n = 1 (approximately 2.0 × 10⁻⁶ and 7.4 × 10⁻⁵ Scm⁻¹, respectively). At about 100 °C, both these samples also exhibit the highest conductivity of the two electrolyte systems (approximately 1.6 × 10⁻⁴ and 1.0 × 10⁻³ Scm⁻¹, respectively). The d-Ut(600)-based xerogel with n = 1 displays excellent redox stability.     

Specific features of the dark conductivity in lithium niobate crystals of congruent composition

The temperature dependence of the dark conductivity in a series of doped and nominally undoped LiNbO₃ crystals of congruent composition is studied. The activation energies for the ionic and electronic contributions to the dark conductivity are determined, and the H⁺, ion diffusion coefficient is estimated. The correlation between the ionic and electronic contributions to the dark conductivity is established.     

Thermal properties and ionic conductivity of Li<Subscript>1,3</Subscript>Ti<Subscript>1,7</Subscript>Al<Subscript>0,3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> solid electrolytes sintered by field-assisted sintering

Li_1,3Ti_0,7Al_0,3(PO₄)₃ (LATP) powder was obtained by a conventional melt-quenching method and consolidated by field-assisted sintering technology (FAST) at different temperatures. Using this technique, the samples could be sintered to relative densities in the range of 93 to 99 % depending on the sintering conditions. Ionic and thermal conductivity were measured and the results are discussed under consideration of XRD and SEM analyses. Thermal conductivity values of 2 W/mK and ionic conductivities of 4?×?10^?4 Scm^?1 at room temperature were obtained using relatively large particles and a sintering temperature of 1000 °C at an applied uniaxial pressure of 50 MPa.