Preparation of polypropylene/ethylene‐propylene‐diene terpolymer/nitrile rubber ternary thermoplastics vulcanizates with good mechanical properties and oil resistance by core‐shell dynamic vulcanization

As the most successful commercialized thermoplastic vulcanizates (TPVs), polypropylene (PP)/ethylene propylene rubber (EPDM) TPVs exhibit poor oil resistance. In this work, we prepared PP/EPDM/butadiene acrylonitrile rubber (NBR) ternary TPVs with good oil resistance using core‐shell dynamic vulcanization. According to the theoretical analysis of the spreading coefficient and the transmission electron microscopy results, the rubber phases exhibited a special core‐shell structure, in which the cross‐linkedNBR‐core was encapsulated by the EPDM‐shell. The core‐shell structure effectively improved the interfacial compatibility between PP and NBR phase as the EPDM‐shell could avoid the direct contact of them, thus improving the mechanical properties of the TPVs. For example, the PP/EPDM/NBR (40/30/30) ternary TPV showed enhanced tensile strength of 12.57 MPa, compared with 10.71 MPa of PP/EPDM (40/60) TPV and 11.11 MPa of PP/NBR (40/60) TPV, respectively. Moreover, the oil resistance of the TPVs was also improved. Compared with PP/EPDM TPV, the change rates in mass, volume, tensile strength and elongation at break of PP/EPDM/NBR TPV after oil immersion decreased by 42.18%, 48.69%, 52.68% and 28.77%, respectively.     

Maleic-anhydride grafted EPM as compatibilising agent in NR/BR/EPDM blends

Incorporation of approximately 30 phr Ethylene-Propylene-Diene rubber (EPDM) into natural rubber (NR)/butadiene rubber (BR) is a means to achieve non-staining ozone resistance for tire sidewall applications. However, due to incompatibility of the elastomers and heterogeneous filler distribution in each of the rubber phases, the mechanical properties deteriorate. In the present work, maleic-anhydride modified EPM (MAH-EPM) is added as a compatibilising agent between NR/BR and EPDM. The addition of 5 phr of MAH-EPM results in significantly improved tensile and tear strength when compared to a straight NR/BR/EPDM blend. These improvements can mainly be attributed to a compatibilising effect of MAH-EPM, resulting in a more homogeneous phase distribution, but in particular a much better homogeneous carbon black distribution over the different rubber phases. In addition, ionic crosslinks are introduced into the blends by interaction of MAH-EPM with zinc oxide.     

TBIR应用于航空胎侧胶的热氧老化性能

研究了反式-1,4-丁二烯-异戊二烯共聚橡胶(TBIR)应用于航空轮胎胎侧胶[天然橡胶(NR)/顺丁橡胶(BR)/TBIR]的耐热氧老化性能.结果表明,与NR/BR硫化胶相比,10～20份质量的TBIR取代BR后,NR/BR/TBIR硫化胶的交联密度明显提高,压缩温升降低2. 2～3. 4℃,耐屈挠疲劳性能提高约100%,填料分散性改善,填料团聚体体尺寸减小,拉伸性能基本不变.随热氧老化时间延长,硫化胶的交联密度先增加后降低,并用TBIR的硫化胶交联密度在老化48 h后趋于平缓.与NR/BR相比,老化后的NR/BR/TBIR硫化胶生热最低,耐屈挠疲劳性最高.     

The Effect of 3-aminopropyltrimethyoxysilane (AMEO) as a Coupling Agent on Curing and Mechanical Properties of Natural Rubber/Palm Kernel Shell Powder Composites

This research is conducted using palm kernel shell powder (PKS) as filler in natural rubber The effect of 3-aminopropyltrimethoxysilane as coupling agent on composites were studied at different palm kernel shell loading i.e, 0 5, 10, 15 and 20 phr The palm kernel shell was crushed and sieved to an average particle size of 5.53 μm The palm kernel shell filled natural rubber composites were prepared using laboratory size two roll mill The curing characteristics such as scorch time, cure time and maximum torque were obtained from rheometer The palm kernel shell powder filled natural rubber composites were cured at 150^oC using hot press according to their cure time Curing characteristics, tensile properties, rubber-filler interaction and morphological properties of palm kernel shell powder filled natural rubber were studied Scorch time and cure time show reduction but tensile strength, elongation at break, modulus at 100% (M100) and modulus at 300% (M300) increased with the presence of 3-aminopropyltrimethyloxysilane Rubber-filler interaction studies showed that rubber filler interaction in natural rubber filled with palm kernel shell powder improved with incorporation of 3-aminopropyltrimethyoxysilane.     

Design of PP/EPDM/NBR TPVs with tunable mechanical properties via regulating the core-shell structure

In this work, polypropylene (PP)/ethylene-propylene-diene monomer (EPDM)/butadiene acrylonitrile rubber (NBR) TPVs with different EPDM/NBR ratios were prepared by the core-shell dynamic vulcanization. The relationship between the core-shell structure and mechanical properties of the TPVs were thoroughly investigated. The formation of core-shell structure by adding NBR is conducive to the mechanical properties of the TPVs. The ratio of EPDM to NBR has an important effect on the structure and performances of the final products, and there is a critical ratio for this effect change. Transmission electron microscope (TEM), tensile test, reprocessing test, ageing test, rheological behavior test and stress relaxation were used to characterize the morphology and properties of the TPVs in detail. It was found that when the ratio of EPDM/NBR was 2:4, the tensile strength increased by ~14% compared with PP/EPDM TPV without NBR. Meanwhile, the reprocessing properties, rheological characteristics and instantaneous tensile deformation, etc. all exhibited sudden changes at this critical ratio.     

Compounding,mechanical and morphological properties of carbon-black-filled natural rubber/recycled ethylene-propylene-diene-monomer (NR/R-EPDM) blends

Blends of natural rubber/virgin ethylene-propylene-diene-monomer (NR/EPDM) and natural rubber/recycled ethylene-propylene-diene-monomer (NR/R-EPDM) were prepared. A fixed amount of carbon black (30 phr) was also incorporated. The effect of the blend ratio (90/10, 80/20, 70/30, 60/40 and 50/50 (phr/phr)) on the compounding, mechanical and morphological properties of carbon-black-filled NR/EPDM and NR/R-EPDM blends was studied. The results indicated that both the carbon-black-filled NR/EPDM and NR/R-EPDM blends exhibited a decrease in tensile strength and elongation at break for increasing weight ratio of EPDM or R-EPDM. The maximum torque (S′M_H), minimum torque (S′M_L), torque difference (S′M_H?M_L), scorch time (ts₂) and cure time (tc₉₀) of carbon-black-filled NR/EPDM or NR/R-EPDM blends increased with increasing weight ratio of virgin EPDM or R-EPDM in the blend. SEM micrographs proved that, for low weight ratios of virgin EPDM or R-EPDM, the blends exhibited high surface roughness and matrix tearing lines. The blends also showed a reduction in crack path with increasing virgin EPDM or R-EPDM content over 30 phr. This reduction in crack path could lead to less resistance to crack propagation and, therefore, low tensile strength.     

Raman investigation of thermoplastic vulcanizates based on hydrogenated natural rubber/polypropylene blends

Raman spectroscopy including mapping technique appears as a powerful technique for the characterization of polymer blends like thermoplastic elastomers (TPEs) and thermoplastic vulcanizates (TPVs). The Raman spectra of polymers blends such as natural rubber/polypropylene (NR/PP) and 65% hydrogenated natural rubber/polypropylene (65%HNR/PP) were identified and the phase distribution was determined. The study was driven for the same type of blends in TPEs state and TPVs state obtained after to 2 different processes, either peroxide cure or sulfur cure. The morphology of TPEs and TPVs obtained by Raman spectroscopy were compared and confirmed using scanning electronic microscopy.Raman mapping shows that the phase morphology of NR/PP, 65%HNR/PP, were characterized as continuous rubber phase morphology of the thermoplastic elastomers (TPEs) and a fine dispersion of cross-linked rubber phase in a continuous matrix of the thermoplastic vulcanizates (TPVs). Raman spectroscopy is demonstrated to be a reference to determine the content ratio of each component in the TPVs. Moreover, Raman mapping could be used to calculate the phase size of cross-linked rubber phase dispersed in the thermoplastic vulcanizates (TPVs).     

Preparation and mechanical properties of water-dispersible hyperbranched polymer grafted carbon black/natural rubber composites by latex blending method

In order to improve the mechanical properties of rubber-matrix composites, carboxyl-terminated hyperbranched poly (2-hydroxypropane-1,2,3-tricarboxylic acid) grafted carbon black (CB-g-CTHBP) was prepared, and it could be stably dispersed in water for up to 90 days. CB-g-CTHBP dispersion and natural rubber latex were blended to obtain NR/CB-g-CTHBP, and the effect of CB-g-CTHBP content on the mechanical properties of composites was discussed. The results show that the dispersibility and wettability of CB-g-CTHBP to composites are significantly improved after grafting hyperbranched polymer onto the surface. Compared with the composite filled with NR/CB, when the amount of filler is 30 phr, tensile strength, tear strength, and shore A hardness of NR/CB-g-CTHBP increase by 54.78%, 55.13%, and 20.96%, respectively. Moreover, CB-g-CTHBP could disperse more evenly in the natural rubber-matrix, and the interaction between CB-g-CTHBP and rubber-matrix could further enhance in the composite.     

Effect of silane coupling agent on the polymer‐filler interaction and mechanical properties of silica‐filled NR

The effects of filler loading and a new silane coupling agent 3‐octanoylthio‐1‐ propyltriethoxysilane (NXT silane) on the polymer‐filler interaction and mechanical properties of silica‐filled and carbon black‐filled natural rubber (NR) compounds were studied. Silica (high dispersion silica7000GR, VN2, and VN3) and carbon black (N330) were used as the fillers, and the loading range was from 0 to 50 phr. The loading of NXT silane was from 0 to 6 phr. Experimental results show that the maximum and minimum torques of silica and carbon black‐filled NR increase with increasing filler loading. With increasing filler loading, the scorch time and optimum cure time decrease for carbon black‐filled NR, but increase for silica‐filled NR. The minimum torque, scorch time, and optimum cure time decrease because of the presence of NXT silane. For the carbon black and silica‐filled NR, the tensile strength and elongation at break have maximum values, but the hardness, M300, M100, and tear strength keep increasing with filler loading. The mechanical properties of silica‐filled NR were improved in the presence of NXT silane. With increasing filler loading, the storage modulus of filled NR increases, but the loss factor decreases. Carbon black shows the strongest polymer‐filler interaction, followed by VN3, 7000GR, and VN2. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 573–584, 2005     

纳米SiO2增强NR/HDPE共混型热塑性弹性体的研究

以动态硫化法制备纳米二氧化硅(SiO2)改性天然橡胶／高密度聚乙烯(NR／HDPE)共混型热塑性弹性体。研究了纳米SiO2对NR／HDPE弹性体力学、耐热变形、耐溶剂和热塑性能的影响，并用SEM分析了弹性体的断面形貌。结果表明：纳米SiO2通过细化交联NR分散相，改善了NR与HDPE的相容性，两相界面粘结强度明显提高。当纳米SiO2质量分数为0．03时，NR／HDPE弹性体的综合性能最好。     

Study on mechanical properties and phase morphology of polypropylene/polyolefin elastomer/magnesium hydroxide ternary composites

In this work, elastomer‐toughened polypropylene (PP)/magnesium hydroxide (MH) composites with ethylene–octene copolymer (POE) were prepared in a twin‐screw extruder and then injection‐molded. The structure, mechanical properties, phase morphology, and rheological behaviors of PP/POE/MH ternary composites were studied. The mechanical properties and fracture behaviors of PP/POE/MH ternary composites are strongly influenced by the incorporation of POE copolymer. The addition of POE causes a significant improvement in the impact strength of the composites, from 3.6 kJ/m² in untoughened composites to 47.4 kJ/m² in PP composites containing 30 phr POE. This indicates that POE is very effective in converting brittle PP composites into tough composites. Conversely, the tensile strength and the Young's modulus of the composites decrease with respect to the PP composites, as the weight fraction of POE is increased to 40 phr. Scanning electron microscopy (SEM) study shows a two‐phase morphology where POE, as droplets, is dispersed finely and uniformly in the PP matrix. The rheological behaviors show that the interfacial interaction in the composites is enhanced with increase in POE content. Interparticle interactions give rise to the formation of interparticle network. Copyright © 2009 John Wiley & Sons, Ltd.     

Compatibilized natural rubber/recycled ethylene-propylene-diene rubber blends by biocompatibilizer

Biocompatibilizer-based refined, bleached, deodorized palm stearin was successfully used as compatibilizer for natural rubber/recycled ethylene–propylene–diene rubber (NR/R-EPDM) blends. It seems effective in improving the state of cure, tensile properties, as well as the swelling resistance and morphology of the blends, indicating an improvement in compatibility between the NR matrix and R-EPDM rendered by biocompatibilizer. This was clearly verified by the dynamic mechanical properties of the blends. The dynamic responses obtained were clearly corresponding to the swelling result. It proves that the cross-link density plays a major role in the changes of storage modulus and degree of entanglement.     

Development of Natural Rubber-Fibrous Nano Clay Attapulgite Composites: The Effect of Chemical Treatment of Filler on Mechanical and Dynamic Mechanical Properties of Composites

Common nano clay fillers have layered structure. Some nano clays like Attapulgite (AT), Sepiolite have rod like fibrous structure. Compared to layered structured clay fibrous clay AT can undergo better dispersion in polymer matrix leading to better improvement in composite properties. Chemical modifications of AT are done through amine treatment as well as by amine+silane treatment to get chemically modified fillers AAT and SAT respectively. In the present investigation, nano composites are prepared using natural rubber (NR) filled with AT, AAT and SAT. Three different loadings of each filler are used namely 2.5, 5, and 10 phr (parts per hundred of rubber). Mechanical properties like tensile strength, elongation at break increase with the increase in filler loading up to 5 phr there after these properties marginally fall when loading is increased to 10 phr due to problem of filler dispersion at higher loading. However, modulus at 300% elongation and tear strength increases with the increase in filler loading up to 10 phr. Very similar trend can also be observed for composites with chemically modified fillers, AAT and SAT. But the degree of reinforcement is higher in the case of AAT and SAT compared to that of unmodified filler AT for the same filler loading. This difference is mainly due to better polymer-filler interaction and filler dispersion in the case of chemically modified clays AAT and SAT compared to unmodified AT. Tear strength of composites increases remarkably with the addition of AT and which is further enhanced when chemically modified clays AAT and SAT are added. Dynamic-mechanical analyses of different clay composites give idea about the difference in the degree of polymer–filler interaction due to chemical treatment of filler.     

Sol–gel derived nano zinc oxide for the reduction of zinc oxide level in natural rubber compounds

Zinc oxide (ZnO) nanoparticles are synthesized by polymeric sol–gel method and characterized by X-ray diffraction, field-emission scanning electron microscopy. The cure characteristics, mechanical properties and thermal behaviour of natural rubber (NR) systems containing nano ZnO are investigated and compared to those of NR with micro-sized (conventional) ZnO. The NR vulcanizate with 0.5 phr (parts per hundred parts of rubber) sol–gel derived nano ZnO shows improvement in the curing and mechanical properties in comparison to the NR vulcanizate with 5 phr conventional ZnO. Thermogravimetric analysis reveals that nano ZnO impose better thermal stability than conventional ZnO in the NR vulcanizates. Thus, nano ZnO not only acts as a curing activator but also nano filler to improve the resulting properties of the NR vulcanizates. More essentially nano ZnO leads to the reduction of ZnO level in the NR compounds. Therefore, sol–gel derived nano ZnO diminishes the pollution of aquatic environment due to higher amount of conventional ZnO in rubber compounds.     

Curing and Physical Properties of Natural Rubber/Wood Flour Composites

Natural rubber based composites were prepared by incorporating Wood flour of two different particle size ranges (250–300 µm) and (300–425 µm) and concentrations (15 and 30 phr) into the matrix, using a Banbury® internal mixer according to a base formulation. Curing characteristics of the samples were studied. Influence of particle size and loading of filler on the properties of the composites was analyzed. Results obtained show that the addition of wood flour to natural rubber increased scorch time and curing time and caused improvement in modulus at 300% strain and in tear properties. However, it decreased tensile strength and elongation at break. The particle size range of 300–425 µm was found to offer the best overall balance of mechanical and dynamic properties (tan δ and viscous torque). Swelling behavior of the composites in toluene was also analyzed in order to determine the rubber volume fraction and crosslinking density. Composites with the bigger particle size wood flour were found to have greater crosslinking density than the ones with smaller particle size, fact that could possibly indicate a better rubber-filler interaction in the former. Major percentage of filler increased slightly this interaction. Water absorption behavior of the composites with wood flour reached a maximum of 12% w/w when 30 phr of filler were incorporated; nonetheless, particle size did not affect this property. The ageing study in presence of air at 70 °C revealed that natural rubber composites with wood flour maintained the same classification cell with temperature as the pure rubber. A compound with 30 phr of carbon black was prepared for comparative purposes. Results obtained were as expected. Scorch time decreased and higher values of modulus at 300% strain and tensile strength were achieved, due to strongest interaction between filler and elastomer.     

Comparison of the effect of mica and talc and chemical coupling on the rheology,morphology, and mechanical properties of polypropylene composites

The effect of filler types of mica and talc on the oscillatory shear rheological properties, mechanical performance, and morphology of the chemically coupled polypropylene composites is studied in this work. The Maleic Anhydride grafted Polypropylene (MAPP) was used as an adhesion promoter for coupling mineral particles with the polypropylene matrix. The samples were prepared by a co‐rotating, L/D = 40, 25 mm twin screw extruder. The tensile tests carried out on the injection molded samples showed a reinforcing effect of talc up to 20 wt% on the Polypropylene (PP). The tensile strength of PP‐mica composites showed a slight decrease at all percentages of mica. The effect of chemical coupling by using MAPP on the tensile strength was more pronounced in increasing the tensile strength for PP‐mica than PP‐talc composites. The complex viscosity curve of pure PP and the composites, showed a Newtonian plateau (η₀) up to 30 wt% at low frequency terminal zone. By increasing the filler content to 40 and 50 wt%, the complex viscosity at very low shear rates sharply increased and showed yield behavior that can be due to the formation of filler particles networks in the melt. At the optimum amount of coupling agent, a minimum in cross over frequency curve against MAPP content is observed. The optimum amount of coupling agent for PP‐talc composites is about 1.5%, and about 3% for PP‐mica formulations. The analysis of viscosity behavior at power‐law high region, revealed the more shear thinning effect of mica than talc on the PP matrix resin. Copyright © 2009 John Wiley & Sons, Ltd.     

Highly enhanced electrical and mechanical properties of methyl methacrylate modified natural rubber filled with multiwalled carbon nanotubes

Developing conductive networks in a polymer matrix with a low percolation threshold and excellent mechanical properties is desired for soft electronics applications. In this work, natural rubber (NR) functionalized with poly(methyl methacrylate) (PMMA) was prepared for strong interfacial interactions with multiwalled carbon nanotubes (MWCNT), resulting in excellent performance of the natural rubber nanocomposites. The MWCNT and methyl methacrylate functional groups gave good filler dispersion, conductivity and tensile properties. The filler network in the matrix was studied with microscopy and from its non-linear viscoelasticity. The Maier-Göritze approach revealed that MWCNT network formation was favored in the NR functionalized with PMMA, with reduced electrical and mechanical percolation thresholds. The obvious improvement in physical performance of MWCNT/methyl methacrylate functionalized natural rubber nanocomposites was caused by interfacial interactions and reduced filler agglomeration in the NR matrix. The modification of NR with poly(methyl methacrylate) and MWCNT filler was demonstrated as an effective pathway to enhance the mechanical and electrical properties of natural rubber nanocomposites.     

Effects of epoxidized natural rubber as a compatibilizer in melt compounded natural rubber-organoclay nanocomposites

Nanocomposites containing natural rubber (NR) as matrix, epoxidized natural rubber (ENR) as compatibilizer and organophilic layered clay (organoclay) as filler were produced in an internal mixer and cured using a conventional sulphuric system. The effects of ENR with 25 (ENR 25) and 50 mol% epoxidation (ENR 50), respectively, were compared at 5 and 10 parts per hundred rubber (phr) concentrations. The organoclay content was fixed at 2 phr. Cure characteristics, clay dispersion, (thermo)mechanical properties of the nanocomposites were determined and discussed. Incorporation of ENR and organoclay strongly affected the parameters which could be derived from Monsanto MDR measurements. Faster cure and increased crosslink density were attributed to changes in the activation/crosslinking pathway which was, however, not studied in detail. The organoclay was mostly intercalated according to X-ray diffraction (XRD) and transmission electron microscopic (TEM) results. The best clay dispersion was achieved by adding ENR 50. This was reflected in the stiffness of the nanocomposites derived from both dynamic mechanical thermal analysis (DMTA) and tensile tests. The tensile and tear strengths of the ENR 50 containing nanocomposites were also superior to the ENR 25 compatibilized and uncompatibilized stocks.     

Mechanical properties and characteristic of surface treated bamboo fiber reinforced PP/PS blends

Bamboo fiber (BF) as organic filler is characterized by mechanical properties analysis and morphology examination for polypropylene (PP) and polystyrene (PS) matrix blends. Effects of different filler content on tensile strength, flexural properties, and impact strength are proposed. It is observed from scanning electron microscopy (SEM) studies that addition of BF is beneficial in increasing mechanical strength via increasing the interface dispersed phase. The optimum tensile properties and impact properties of BF content were at 40 wt% for PP/PS/BF composite on melt mixing conditions. The results showed a significant improvement in mechanical properties of PP/PS/BF ternary blend composite. Comparing with untreated BF, content of carbon and nitrogen of treated BF decreased to 66.57 and 2.31%, oxygen content increased to 21.07%, and silicon content increased from 0 to 10.04%. The element ratio of O/C, N/C, and Si/C changed to 31.65, 3.47, and 15.08, respectively.     

Uncross‐linked polypropylene (PP)/ethylene‐propylene‐diene (EPDM)/multi walled carbon nanotube (MWCNT) and dynamically vulcanized PP/EPDM/MWCNT nanocomposites

In this study, relatively large amounts of polypropylene (PP), ethylene‐propylene‐diene (EPDM), and multi‐walled carbon nanotube (MWCNT) were melt‐mixed with and without DCP. Dynamically vulcanized PP/EPDM (TPV)/MWCNT nanocomposites were prepared by two methods: the MWCNTs were added either before or after the dynamic vulcanization of the blends. The effects of composition, rotor speed, and dynamic vulcanization on their surface resistivity were investigated. The surface resistivity of uncross‐linked PP/EPDM/MWCNT nanocomposites increases with increasing the content of EPDM. At PP/EPDM (70/30 wt%) nanocomposite with 1.5 phr MWCNT, slightly lower surface resistivity is obtained by increasing the rotor speed during mixing. However, for PP/EPDM (50/50 wt%) and PP/EPDM (30/70 wt%) nanocomposites, surface resistivity decreases with increasing the rotor speed from 30 to 60 rpm. But further increase in rotor speed (90 rpm) leads to an increase of surface resistivity. When the MWCNTs were added after the dynamic vulcanization of the blends, the surface resistivity of TPV70/MWCNTnanocomposite is lower than that of uncross‐linked PP/EPDM/MWCNT nanocomposite. However, when the MWCNTs were added before the dynamic vulcanization of the blends, the surface resistivity of TPV70/MWCNT nanocomposite is >10¹² Ω/square. Copyright © 2010 John Wiley & Sons, Ltd.