Separation of Americium from Lanthanides by Purified Cyanex 301 Countercurrent Extraction in Miniature Centrifugal Contactors

In order to further test the actinides/lanthanides separation performance by Cyanex 301 extraction, a countercurrent extraction experiment was carried out in the present work. The separation process consisted of 7-stage extraction, 3-stage scrubbing and 4-stage stripping. 14 miniature centrifugal contactors were installed in glove box for the experiment. The feed solution from TRPO process, mainly consisting of 4.4 M HNO3, ∼3.7×10⁸Bq Am-241, 0.02 M lanthanides, ∼120 ppm Mo and 100 ppm Fe, was pretreated by the following procedures: denitrating to 0.2 M HNO3 by formic acid, adjusting pH to 2 by 8 M NaOH, removing most Fe³⁺ by 0.2 M Cyanex 301-kerosene cross-flow extraction, and then adjusting pH to 3.5 by 1 M NaOH. About 5.6×10⁸Bq Pm-147 was added into the feed solution to trace lanthanides during the experiment. The experiment lasted for 9 hours with a feed flow rate of 30 ml/h. The results show that 99.95% Am was separated from lanthanides and only 0.1% lanthanides were extracted together with Am. 99.3% Am and 96.6% Pm were stripped from load Cyanex 301 by 1.0 M HNO3, respectively.     

Thermodynamic study of Eu(III) complexation by pyridine monocarboxylates

The thermodynamic parameters (log K, ΔG, ΔH and ΔS) of complexation of Eu(III), a chemical analogue of trivalent actinides, with pyridine monocarboxylates, namely, picolinic acid (pyridine-2-carboxylic acid), nicotinic acid (pyridine-3-carboxylic acid), isonicotinic acid (pyridine-4-carboxylic acid) have been studied at 1.0 M ionic strength adjusted by NaClO₄ and 298 K by potentiometry, fluorescence spectroscopy and calorimetry. The potentiometric results revealed formation of four complexes, ML_i (i = 1–4) in case of picolinate whereas only ML complexes in case of nicotinate and isonicotinate. The log K_ML for Eu(III) picolinate complex is higher than that for complexes of Eu(III) with the other two acids. The complexation reaction between Eu(III) and picolinate was found to be exothermic due to chelate formation via pyridyl nitrogen. In case of complexation of Eu(III) with nicotinate and isonicotinate, the enthalpy changes are similar as in the case of simple mono carboxylates and are positive. Life time measurements by time resolved fluorescence spectroscopy, for the decay of ⁵D₀ state of Eu(III) also indicated the formation of ML₄ with picolinate and formation of ML only with the other two acids. The experimental observations on the stability and binding mode of the complexes are corroborated by theoretical calculations using the TURBOMOLE software. The detail analysis of calculated charge values of the free ligands and the complexes indicates that charge polarization is more in the isonicotinate than in nicotinate upon complexation.     

Neptunium(III) application in extraction chromatography

This paper describes a novel strategy for actinide separation by extraction chromatography with Np(III) valence adjustment. Neptunium(IV) was reduced to Np(III) using Cr(II) and then selectively separated from uranium (IV) on a TEVA resin. After elution, Np(III) was retained on a DGA resin in order to remove any detrimental chromium impurities. Neptunium(III) formation was demonstrated by the complete and selective elution of Np from TEVA resin (99 ± 7%) in less than 12 mL of 9 M HCl from U(IV) (0.7 ± 0.7%). It was determined by UV–visible and kinetic studies that Cr(II) was the only species responsible for the elution of Np(IV) as Np(III) and that the Cr(II) solution could be prepared from 2 to 30 min before its use without the need of complex degassing systems to prevent the oxidation of Np(III) by oxygen. The methodology proposed here with TEVA/DGA resins provides removal of Cr(III) impurities produced at high decontamination factors (2.8 × 10³ and 7.3 × 10⁴ respectively).     

Reversed phase extraction chromatographic separation of ruthenium(III)

A new an innovative separation method has been developed using N-n-octylaniline (liquid anion exchanger) coated on silica gel. Ruthenium(III) has been extracted quantitatively from 0.05 M hydrochloric acid, striped with aqueous solution of various acids and then determined by spectrophotometric method. Mutual separation scheme for ruthenium(III), iridium(III) and osmium(VIII) has been developed. Ruthenium(III) has been separated from commonly associated elements. Different parameter are studied viz effect of acid concentration, reagent concentration, striping agent, flow rate, foreign ion and synthetic mixture corresponding to alloys. Validity of method has been verified by separation of ruthenium(III) from fissium alloy.     

Studies on Separation of 90Y and 90Sr Separation from Hydrochloric Acid Solutions Using TODGA as the Extractant by SLM Method

Yttrium-90 is an important radionuclide known for its therapeutic application in nuclear medicine. Solvent extraction studies with N,N,N’,N’-tetra-octyldiglycolamide (TODGA) has shown that Y(III) is well extracted in 6 M HCl while at the same time, extraction of Sr(II) is very low leading to a separation factor (DY/DSr = 60,000). This property of TODGA can be exploited for the separation of Y from Sr. The aim of this present work is to produce carrier free ⁹⁰Y by using Supported Liquid Membrane (SLM) based separation of Y and Sr with TODGA as the carrier. Solvent extraction studies with various diluents viz. 1-decanol, xylene, MIBK, chloroform etc. indicated that xylene and n-dodecane are most suitable as S.F. >50,000 are obtained. Based on the results, a SLM based separation scheme was developed using 0.1 M TODGA in xylene loaded on a microporous PTFE membrane as a polymeric support and 6 M HCl as feed and 0.01 M HCl as strip phase. The results appear promising for the development of SLM based Y-90 generator. The purity of the product was ascertained by the half life method.     

The Recovery of An(Iii) in an Innovative-Sanex Process using a Todga-based Solvent and Selective Stripping with a Hydrophilic BTP

The development of an innovative-SANEX process for the selective recovery of trivalent actinides from PUREX raffinate using a TODGA/1-octanol based solvent is presented. CDTA was used to efficiently mask Zr and Pd. Two options were studied for the selective An(III) stripping. First, a glycine-buffered DTPA solution was successfully employed. A great improvement was the use of the hydrophilic SO3-Ph-BTP, which allowed the selective An(III) stripping even at 0.5 mol/L HNO3 without using buffering or salting-out agents, making the advanced partitioning process easier and more efficient. High Ln/Am separation factors were achieved in single centrifugal contactor tests.     

Dual-signal anodic stripping voltammetric determination of trace arsenic(III) at a glassy carbon electrode modified with internal-electrolysis deposited gold nanoparticles

A glassy carbon electrode (GCE) modified with internal-electrolysis deposited gold nanoparticles (AuNPs_ied) was applied to sensitively and selectively detect As(III) by anodic stripping linear sweep voltammetry (ASLSV). The AuNPs_ied/GCE was prepared based on the redox replacement reaction between a supporting-electrolyte-free aqueous HAuCl₄ and a copper sheet in saturated KCl separated by a salt bridge. Under optimum conditions (0.5 M aqueous H₂SO₄, 300-s preconcentration at − 0.4 V), the ASLSV peak current for the As(0)–As(III) oxidation responded linearly to As(III) concentration from 0.02 to 3 μM with a limit of detection (LOD) of 0.9 nM (0.07 μg L^− 1) (S/N = 3), while that for the As(III)–As(V) oxidation was linear with As(III) concentration from 0.02 to 1 μM with a LOD of 4 nM (0.3 μg L^− 1) (S/N = 3). An appropriate high-scan-rate for ASLSV can enhance both the sensitivity and signal-to-noise ratio. This method was applied for analyses of As(III) in real water samples.     

Flame atomic absorption spectrometry determination of trace amount of gold after separation and preconcentration onto ion-exchange polyethylenimine coated on Al2O3

The object of this work is to develop a simple and selective method for efficient extraction of Au(III) ions in aqueous solution using a new solid-phase extraction sorbent. Polyethylenimine (PEI) ion-exchange polymer was coated on alumina in the presence of NaNO₃. The method is based on sorption of Au³⁺ ions on 50 mg PEI/Al₂O₃. A solution of 0.5 M thiourea, then 1.0 M HCl effectively eluted the gold ion and then aspirated into flame atomic absorption spectroscopy (FAAS). The influence of flow rate of sample solution and eluent, the pH effect, eluent type and sorption capacity was investigated. The effects of various diverse ions for preconcentration and separation of the gold ion were investigated. Relative standard deviation of 4.0 μg mL⁻¹ of gold was 1.46% (n = 10). The detection limit was 26.2 ng L⁻¹ in original solution. The method has been applied successfully for the recovery of trace amount of Au(III) ions from water samples.     

Anodic stripping voltammetric analysis of trace arsenic(III) enhanced by mild hydrogen-evolution at a bimetallic Au–Pt nanoparticle modified glassy carbon electrode

A glassy carbon electrode (GCE) modified with electrodeposited bimetallic Au–Pt nanoparticles (Au–PtNPs) was applied to sensitively detect As(III) by linear sweep anodic stripping voltammetry (LSASV). In 0.5 M aqueous H₂SO₄, atomic hydrogen and molecular hydrogen were easily electrogenerated at the Pt sites on Au–PtNPs/GCE, which can chemically reduce As(III) to As(0) and enhance the cathodic preconcentration of As(0) at both the Pt sites and the neighboring Au sites. Since the As(0)–Au affinity is weaker than the As(0)–Pt affinity, the preconcentrated As(0) can be rapidly oxidized on/near the surface Au sites of Au–PtNPs/GCE, yielding sharper and higher LSASV current peaks. Under optimum conditions (700 s preconcentration at − 0.1 V, 5 V s^− 1), the LSASV peak current for the As(0)–As(III) oxidation responded linearly to As(III) concentration from 0.005 to 3.0 μM with a limit of detection (LOD) of 3.7 nM (0.28 ppb) (S/N = 3), while that for the As(III)–As(V) oxidation was linear with As(III) concentration from 0.01 to 3.0 μM with a LOD of 6.0 nM (0.45 ppb) (S/N = 3). This method was applied for analysis of As(III) in real water samples.     

Reactivity of sugar cane bagasse as a natural solid phase extractor for selective removal of Fe(III) and heavy-metal ions from natural water samples

This work introduces the feasibility of using sugar cane bagasse (SCB) – a sugar cane industry waste – as a selective solid phase extractor for Fe(III). The order of metal uptake capacities in μmol g^?1 for the extraction of six tested metal ions from aqueous solution using static technique is Fe(III) > Cu(II) > Pb(II) > Zn(II) > Cd(II) > Co(II). Since SCB exhibits remarkable binding characteristics for Fe(III), special interest was devoted for optimizing its uptake and studying its selectivity properties under static and dynamic conditions. In this respect, batch experiments were carried out at the pH range 1.0–4.0, initial concentration of metal ion (10–100 μmol), weight of phase (25, 50, 75, 100, 125 and 150 mg) and shaking time (10, 30, 45, 60, 90, 120 and 150 min). FT-IR spectra of SCB before and after uptake of Fe(III) were recorded to explore the nature of the functional groups responsible for binding of Fe(III) onto the studied natural biosorbent. The equilibrium data were better fitted with Langmuir model (r² = 0.985) than Freundlich model (r² = 0.934). Moreover, Fe(III) sorption was fast and completed within 60 min. The adsorption kinetics data were best fitted with the pseudo-second-order type. As a view to find a suitable application of SCB based on its unique property as a benign sorbent, it was found that, Fe(III) spiked natural water samples such as doubly distilled water (DDW), drinking tap water (DTW), natural drinking water (NDW), ground water (GW) and Nile River water (NRW) was quantitatively recovered (>95.0%) using batch and column experiments, with no matrix interferences.     

Selective Separation of Re(VII) and Tc(VII) by Xerogel Microcapsules Enclosing TOA Extractant

Special attention has been given to the separation and recovery of VII-group elements, Tc and Re, in relation to the partitioning of high-level liquid waste (HLLW) generated from the nuclear fuel reprocessing process. In this study, a tertiary amine (tri-n-octylamine, TOA), which is effective for the extraction of oxoanions, was encapsulated in Ca and H-types of alginate xerogel polymers (CaALG, HALG). The uptake behaviors of TcO4^-and ReO4⁻ (substitute of Tc) in the presence of HNO3 were examined by batch method using TOA-xerogel microcapsules (TOA-CaALG, TOA-HALG). The uptake of TcO4- in the presence of 0.1 M HNO3 was readily attained within 5 h, and a relatively large uptake(%) above 90% was obtained. The uptake(%) of Re(VII) for TOA-CaALG in the presence of 0.01∼0.1 M HNO3 was estimated to be about 90%, while gradually decreasing with HNO3 concentration, indicating that the extraction of HNO3 with TOA became dominant in this process: R3NH⁺NO3 (o) + ReO4 (aq) ↔ R3NH⁺ReO4 (o) + NO3 (aq). The order of the uptake(%) for different oxoanions in the presence of 0.01∼5 M HNO3 was Re(VII) > Zr(IV)> Se(VI) > Mo(VI) > Te(VI). The elution study of Tc(VII) revealed 95% and 99% of recovery with 5 M and 7 M HNO3, respectively. The chromatographic separation of Re(VII) from simulated HLLW (28 components of waste solution, SW-11E, JAEA) as well as from mixed solution was accomplished by the stepwise elution techniques using a column packed with TOA-MCs. The Re(VII) ions were effectively eluted with 5 M HNO3, and a relatively large recovery(%) of 98.60% was obtained. Other elements were eluted with H2O and 2 M HNO3. Thus the TOA-xerogel microcapsules are effective for the selective separation of Tc(VII) from HLLW.     

Photophysical properties of clozapine and determination of its concentration by using Eu(III)–dipicolinic acid complex as photo probe

Clozapine drug is photo-stable under irradiation of light for a long time, so we can store it in difficult and hot conditions. In addition the activity of clozapine is inhibited of the absorption spectra in the presence of glucose and enhanced in the presence of iron(III). We succeeded in detecting the concentration of clozapine in the range 1–60 × 10^?9 M using Eu(III)–dipicolinic acid complex as photo probe type and using Stern–Völmer equation to determine the Stern–Völmer constant, critical radius and the mechanism of quenching of luminescence of Eu(III)–dipicolinic acid complex is found to be of dipolar–dipolar interaction.     

Synthesis and spectroscopic characterization of new tetradentate Schiff base and its coordination compounds of NOON donor atoms and their antibacterial and antifungal activity

New Schiff base (H₂L) ligand is prepared via condensation of o-phthaldehyde and 2-aminobenzoic acid in 1:2 ratio. Metal complexes are prepared and characterized using elemental analyses, IR, solid reflectance, magnetic moment, molar conductance, ¹H NMR, ESR and thermal analysis (TGA). From the elemental analyses data, the complexes were proposed to have the general formulae [MCl(L)(H₂O)]·2H₂O (where M = Cr(III) and Fe(III)); [M(L)]·yH₂O (where M = Mn(II), Ni(II), Cu(II) and Zn(II), y = 1–2) and [M(L)(H₂O)_n]·yH₂O (where M = Co(II) (n = y = 2), Co(II) (n = y = 1), Ni(II) (n = 2, y = 1). The molar conductance data reveal that all the metal chelates were non-electrolytes. IR spectra show that H₂L is coordinated to the metal ions in a bi-negative tetradentate manner with NOON donor sites of the azomethine-N and carboxylate-O. The ¹H NMR spectral data indicate that the two carboxylate protons are also displaced during complexation. From the magnetic and solid reflectance spectra, it was found that the geometrical structure of these complexes are octahedral (Cr(III), Fe(III), Co(II) and Ni(II)), square planar (Cu(II)), trigonal bipyramidal (Co(II)) and tetrahedral (Mn(II), Ni(II) and Zn(II)). The thermal behaviour of these chelates showed that the hydrated complexes losses water molecules of hydration in the first step followed immediately by decomposition of the ligand molecule in the subsequent steps. The biological activity data show that the metal complexes to be more potent/antibacterial than the parent Shciff base ligand against one or more bacterial species.     

Selective determination of uric acid with DNA doped polymers modified carbon fiber microelectrode

New biocomposite materials, based on the incorporation of DNA doped p-aminobenzensulfonic acid, was fabricated by electrochemical method. A carbon fiber microelectrode modified by this thin film was fabricated for selective determination of uric acid (UA) in the presence of a larger amount of ascorbic acid (AA). It was found that the voltammetric oxidation peak separation between UA and AA is about 260 mV at the modified electrode. A linear response of the peak current versus the concentration was found in the range of 8 × 10⁻⁷–6 × 10⁻⁴ M with correlation coefficient of 0.9991 and the detection limit was 5 × 10⁻⁷ M (s/n = 3) at the 5 × 10⁻⁴ M AA. The presence of high concentration AA did not interference the determination. The electropolymerized film was characterized by SEM techniques. The modified electrode shows good sensitivity, selectivity and stability.     

Thermal investigation and infrared evolved gas analysis of light lanthanide(III) complexes with pyridine-3,5-dicarboxylic acid

The characterisation of light lanthanide(III) complexes with pyridine-3,5-dicarboxylic acid of the formula Ln₂pdc₃·nH₂O where Ln denotes lanthanides from La to Gd, pdc = C₇H₅NO₄²⁻; n = 6 for Ce(III), n = 7 for Pr(III) and Sm(III), n = 8 for La and n = 13 for Nd(III), Eu(III) and Gd(III) was performed by the thermal analysis TG-DTA and the simultaneous infrared evolved gas analysis TG-FTIR. Heating of the crystalline complexes resulted in the dehydration process at first. Next, dehydrated compounds decompose releasing of CO₂, CO, CH₄ and hydrocarbons. Free pyridine molecules were detected only in the gaseous products of lanthanum(III) complex decomposition.     

Sodium dodecyl sulfate modified carbon nanotubes paste electrode as a novel sensor for the simultaneous determination of dopamine,ascorbic acid,and uric acid

A novel modified multiwall carbon nanotubes paste electrode with sodium dodecyl sulfate as a surfactant (SDS) has been fabricated through an electrochemical oxidation procedure and was used to electrochemically detect dopamine (DA), ascorbic acid (AA), uric acid (UA), and their mixture by cyclic voltammetry (CV) and differential voltammetry (DPV) methods. Several factors affecting the electrocatalytic activity of the hybrid material, such as the effect of pH, of the scan rate and of the concentration were studied. The bare carbon nanotubes paste electrode (BCNTPE) and SDS-modified carbon nanotubes paste electrode (SDSMCNTPE) were characterized using Field Emission Scanning Electron Microscopy (FESEM) and Energy-Dispersive X-ray spectroscopy (EDX). Using the CV procedure, a linear analytical curve was observed in the 1 × 10⁻⁶–2.8 × 10⁻⁵ M range with a detection limit at 3.3 × 10⁻⁷ M in pH 6.5, 0.2 M phosphate buffer solutions (PBS).     

Determination of traces of Sb(III) using ASV in Sb-rich water samples affected by mining

Chemical speciation [Sb(V) and Sb(III)] affects the mobility, bioavailability and toxicity of antimony. In oxygenated environments Sb(V) dominates whereas thermodynamically unstable Sb(III) may occur. In this study, a simple method for the determination of Sb(III) in non acidic, oxygenated water contaminated with antimony is proposed. The determination of Sb(III) was performed by anodic stripping voltammetry (ASV, 1–20 μg L⁻¹ working range), the total antimony, Sb(tot), was determined either by inductively coupled plasma mass spectrometry (ICP-MS, 1–100 μg L⁻¹ working range) or inductively coupled plasma optical emission spectrometry (ICP-OES, 100–10,000 μg L⁻¹ working range) depending on concentration. Water samples were filtered on site through 0.45 μm pore size filters. The aliquot for determination of Sb(tot) was acidified with 1% (v/v) HNO₃. Different preservatives, namely HCl, L(+) ascorbic acid or L(+) tartaric acid plus HNO₃, were used to assess the stability of Sb(III) in synthetic solutions.The method was tested on groundwater and surface water draining the abandoned mine of Su Suergiu (Sardinia, Italy), an area heavily contaminated with Sb. The waters interacting with Sb-rich mining residues were non acidic, oxygenated, and showed extreme concentrations of Sb(tot) (up to 13,000 μg L⁻¹), with Sb(III) <10% of total antimony. The stabilization with L(+) tartaric acid plus HNO₃ appears useful for the determination of Sb(III) in oxygenated, Sb-rich waters. Due to the instability of Sb(III), analyses should be carried out within 7 days upon the water collection. The main advantage of the proposed method is that it does not require time-consuming preparation steps prior to analysis of Sb(III).     

Macroporous chitin affinity membranes for wheat germ agglutinin purification from wheat germ

Macroporous chitin membranes of controlled porosity and pore sizes have been prepared. They have good mechanical properties and allow high flow rates of protein solutions at low pressure drops. Because of the numerous N-acetyl-D-glucosamine (GlcNAc) moieties they contain, the chitin membranes can be used for the separation of some valuable proteins both as affinity ligands and support matrix, without further modification. Due to their high porosity and high adsorption surface area, the chitin membranes provide a larger number of accessible binding sites for the wheat germ agglutinin than the chitin beads do. The adsorption capacity for wheat germ agglutinin (180 mg/g chitin membrane) is about 20 times larger than that of chitin beads. Because of the numerous binding sites, multiple-point bindings are involved in the protein adsorption. For this reason, a strong eluant, namely a 1 M acetic acid aqueous solution, had to be used to efficiently recover the wheat germ agglutinin from the membrane. The wheat germ agglutinin was extracted from wheat germ with 0.05 M HCl, precipitated with ammonium sulfate, dialyzed against 0.01 M Tris–HCl buffer (pH 8.5), and purified on the chitin membrane. A high purity (>99%) wheat germ agglutinin with high yield (∼50 mg/100 g wheat germ) was obtained.     

Determination of gallium at trace levels using a spectrofluorimetric method in synthetic U–Ga and Ga–As solutions

A simple, easy to use and selective spectrofluorimetric method for the determination of trace levels of gallium has been developed. A new Schiff base, N-o-vanillidine-2-amino-p-cresol (OVAC) was synthesized and its fluorescence activity with gallium investigated. Based on this chelation reaction, a spectrofluorimetric method has been developed for the determination of gallium in synthetically prepared Ga–U and Ga–As samples buffered at pH 4.0 using acetic acid–sodium acetate. The chelation reaction between Ga(III) and N-o-vanillidine-2-amino-p-cresol was very fast, requiring only 30 min at room temperature to complex completely. The limit of detection (LOD) (3σ) for Ga(III) was 7.17 nM (0.50 μg L^?1), determined from the analysis of 11 different solutions of 20 μg L^?1 Ga(III).     

Thermoluminescence analyses of irradiated dried sea foods using different methods of mineral separation

This research was conducted to find the most suitable parameters to separate minerals from irradiated dried shrimps and mussels (0 and 5 kGy) for thermoluminescence analysis using density separation and modified acid hydrolysis (at 50 °C with continuous agitation) methods. Nonirradiated samples gave TL glow curve of low intensity with peak after 300 °C except dried mussel sample, which gave false positive result. This problem was absent in minerals separated by acid hydrolysis. TL ratios of all nonirradiated samples were <0.1 irrespective of method used for mineral separation. Minerals separated from irradiated samples by density separation showed very high intensity of TL glow peak before 200 °C, where results from irradiated dried shrimp samples were better because of good availability of minerals. The minerals separated from irradiated samples by acid hydrolysis showed slightly low TL intensity and glow curve peak was found at about 200 °C. However, acid hydrolysis method was less laborious and required less sample weight as compared to density separation method. TL ratios of all irradiated samples were >0.1 confirming the quality of minerals on TL discs.