NafionTM膜表面改性用等离子体聚合方法提高膜的阳离子选择性

采用辉光放电等离子体聚合方法 ,以 C2 H4 和 NH3 为单体 ,在 Nafion TM膜表面沉积一层含氨基及酰氨基的类聚乙烯阴离子交换膜 ,提高了 Nafion TM膜对阳离子的选择性 ,同时不显著增加膜电阻 .由 SEM确定该等离子体聚合膜厚约 0 .5μm,用红外光谱及 X光电子能谱表征膜结构 .采用四电极法测量膜电阻 ,膜对质子的选择性由 Cu2 + 的迁移数 t Cu表征 ,用二室隔膜装置 (0 .2 5mol/L Cu Cl2 -0 .5mol/L HCl|等离子体处理膜 |1 mol/L HCl)测量 t Cu. O2 等离子体预处理 Nafion TM膜有利于沉积膜在 Nafion TM膜上的沉积并与 Nafion TM膜紧密结合 .经改性后的 Nafion TM膜电阻值仍然很小 ,在 1 mol/L HCl溶液中电阻小于 0 .5Ω· cm2     

纯铝在强碱溶液中阳极溶解的电化学阻抗谱解析

依据曹楚南提出的法拉第导纳表达式，拟合了纯铝在强碱溶液中的阳极溶解过程的电化学阻抗谱，并据此提出了这一反应进行的机理.结果表明,阻抗谱中的低频容抗弧是由表面裸露的Al转变为中间产物Al(OH)ads的反应引起的，而中频感抗弧则由Al(OH)ads转变为Al(OH)3,ads的反应引起.法拉第导纳的时间常数τ1和τ2的物理意义是物种Al(ss)和Al(OH)ads在单位表面活性位上的转化时间. τ1 >0和τ2 >0是符合稳定性条件的，也能够满足Kramers-Kronig转化的必要条件. g1和g2是与物种Al(ss)和Al(OH)ads在电极表面的覆盖密度随电位E变化有关的参数，由g1< 0可知随电位升高，纯铝表面的活性位面积减小.     

酶促开环聚合与自缩合乙烯基共聚合相结合制取超支化聚合物

在Novozyme 435脂肪酶催化下, 甲基丙烯酸羟乙酯(HEMA)引发己内酯(ε-CL)开环聚合反应, 得到一端为双键, 另一端为羟基的直链聚己内酯(PCL)产物; 将其端羟基官能化得到大分子AB*型单体, 与苯乙烯以原子转移自由基聚合(ATRP)反应形式进行自缩合乙烯基共聚合, 得到超支化结构聚苯乙烯-b-聚己内酯产物.     

NafionTM膜表面改性用等离子体聚合方法提高膜的阳离子选择性

采用辉光放电等离子体聚合方法,以C     

Fabrication of Multicomponent Polymer Nanostructures Containing PMMA Shells and Encapsulated PS Nanospheres in the Nanopores of Anodic Aluminum Oxide Templates

Multi‐component polymer nanomaterials have attracted great attention because of their applications in areas such as biomedicine, tissue engineering, and organic solar cells. The precise control over the morphologies of multi‐component polymer nanomaterials, however, is still a great challenge. In this work, the fabrication of poly(methyl methacrylate)(PMMA)/poly­styrene (PS) nanostructures that contain PMMA shells and encapsulated PS nanospheres is studied. The nanostructures are prepared using a triple solution wetting method with anodic aluminum oxide (AAO) templates. The nanopores of the templates are wetted sequentially by PS solutions in dimethylformamide (DMF), PMMA solutions in acetic acid, and water. The compositions and morphologies of the nanostructures are controlled by the interactions between the polymers, solvents, and AAO walls. This work not only presents a feasible method to prepare multi‐component polymer nanomaterials, but also leads to a better understanding of polymer‐solvent interactions in confined geometries.

     

基团转移活性聚合物的接枝共聚

以阴离子聚合法合成的窄分布聚苯乙烯（ＮＤＰＳ）进行氯甲基化后,再与由基团转移聚合法合成的活性聚甲基丙烯酸甲酯（ＰＭＭＡ）进行大分子反应,得到了主链为聚苯乙烯,支链为聚甲基丙烯酸甲酯的接枝共聚物（ＰＳｔｇＰＭＭＡ）;探讨了聚合物的合成条件,ＧＰＣ测试结果表明,得到的接枝共聚物的分子量和设计分子量相近且主链和支链分子量均可较好的控制．利用扫描电镜、核磁和红外技术对ＰＳｔｇＰＭＭＡ的形态、结构进行了表征．     

折射率梯度型塑料光纤棒的制备与模拟

采用溴苯作为高折射率掺杂剂，通过界面凝胶聚合法制备了折射率呈梯度型分布的塑料光纤棒，研究发现，在聚合反应前期，混合物在真空与60－70℃的条件下聚合，而后期反应在高压气氛中进行，可以消除光纤棒中的气泡或真空泡，利用Vrentas-Duda自由体积理论，对梯度型折射率分布的形成进行了分析，建立了物理模型，并进行了模拟分析。     

Synthesis and Sorption Behaviour of Some Radioactive Nuclides on Sodium Titanate as Cation Exchanger

Crystalline (Na₄TiO₄·0.32H₂O) and amorphous (Na₂TiO₃·1.45H₂O) forms of sodium titanate were prepared by fusion reaction of TiO₂ and Na₂CO₃ at 1100°C in molar ratios of 2:1 and 1:2, respectively. The prepared products were characterized using IR, DTA-TG, X-ray and elemental analyses. Kinetic studies of the order of reaction (n) and activation energy (E _a) for crystallization transformation step (for crystalline sodium titanate only) have been determined from DTA thermogram and their values were found to be 0.87 (univalent order) and 3.97 kJ mol^–1, respectively. Ion exchange capacities and some distribution studies were carried out at different conditions in the presence of some complexing agents (EDTA, boric and citric acids) and the results showed that the capacities of the crystalline form are always less than the amorphous one.     

水溶液悬浮聚合法制备妥拉苏林分子印迹聚合物微球及其性能研究

以药物妥拉苏林为印迹分子,甲基丙烯酸（MAA）为功能单体,乙二醇二甲基丙烯酸酯（EDMA）为交联剂,采用水溶液悬浮聚合方法,制得对妥拉苏林有较好选择识别能力的球形分子印迹聚合物（molecularly imprinted polymer,MIP）。扫描电子显微镜（SEM）照片显示MIP微球粒径为50～200μm,静态平衡吸附实验表明,MIP对妥拉苏林的吸附量是95.28μmol/L,而空白分子印迹聚合物（non-imprinted polymer,NIP）的吸附量是52.66μmol/L,氮气吸附法测得MIP和NIP的比表面积分别为27.17 m^2/g和10.27 m^2/g。将所得的MIP应用于固相萃取（SPE）的固定相,结果表明,该MIP能选择性吸附妥拉苏林,当以结构类似的药物萘甲唑啉为竞争底物时,分离因子可达1.75。MIP用于人尿样的分离和富集时,回收率为99%～114%,相对标准偏差为1.5%～2.5%。     

乙烯基吡咯烷酮与二乙烯基苯原位共聚有机多孔高聚物毛细管柱的制备与性能

以乙烯基吡咯烷酮为单体，二乙烯基本为交联剂原位聚会制备出有机多孔高聚物OPPLOT－R型毛细管柱，对柱子的色谱性能进行了评价，考察了水以及载气中的O2，乙烯基吡咯烷酮含量的变化等对柱性能的影响，并对柱子的分离机理进行了初步探讨，最后给出了一些分析的实例。     

Electrochemical Polymerization of Benzene by use of Aluminum Chloride and Copper(I) Chloride

Electrochemical polymerization of benzene has been carried out in a one-compartment cell using indium-tin oxide conducting glass as a working electrode and Pt mesh as a counterelectrode by the use of a composite electrolyte of aluminum chloride and copper(I) chloride in nitrobenzene. On applying a constant voltage at + 1.8 V vs SCE, a brown and flexible polyparaphenylene (PPP) film was smoothly obtained on the ITO anode surface. The electrical conductivity of the film as grown was 1.9 × 10^?5 S/cm. Aluminum and chlorine atoms were detected in the film from XPS studies, so the film might contain AlCl₄ ^? (and Cl^?) as a dopant. Scanning electron micrographs of the growing side surface of the film prepared at a constant potential of + 1.8 V vs SCE showed a fibrillar morphology. The fibril diameter (～100 nm) was similar to that of a polyaniline film. The PPP film exhibited a spin concentration of 1.0 × 10¹⁹ spins/g, which corresponds to 800 phenylene units per spin. The g-value and the peak-to-peak linewidth were 2.0045 and 7 G, respectively.     

三羟甲基丙烷三丙烯酸酯-甲基丙烯酸甲酯沉淀聚合制备单分散聚合物微球

以三羟甲基丙烷三丙烯酸酯(TMPTA)为交联剂,甲基丙烯酸甲酯(MMA)为共聚单体,偶氮二异丁腈为自由基引发剂,以乙醇或乙醇-水混合物作溶剂,在2 wt%的单体浓度下通过沉淀聚合制备了交联聚合物微球.探究了聚合时间、混合溶剂的含水量以及交联剂TMPTA用量对聚合过程及聚合产物的影响.结果表明,增加TMPTA用量可提高单体转化率和微球产率;所得微球的粒径则随着TMPTA用量的增加而减小.TMPTA用量占单体总量40 wt%至80 wt%,反应时间不少于6 h时可制得高度单分散聚合物微球,产率达到80%以上.在反应介质中加入水可明显提高单体转化率和微球产率,当混合溶剂中水的体积分数为35%时,仍可制得高度单分散聚合物微球,产率可达94%;但当混合溶剂中水的体积分数达40 vol%时,所得微球的多分散系数增大.     

Size-Exclusion Effect and Protein Repellency of Concentrated Polymer Brushes Prepared by Surface-Initiated Living Radical Polymerization

The adsorption of proteins on poly(2-hydroxyethyl methacrylate) (PHEMA) brushes was systematically investigated from the viewpoint of the size-exclusion effect of the concentrated brushes. By use of surface-initiated atom transfer radical polymerization, well-defined, concentrated PHEMA brushes were successfully grafted on the inner surface of the silica monolithic column with meso pores of ca. 80 nm as well as a silicon wafer and a quartz crystal microbalance (QCM) chip. By eluting low-polydispersity pullulans with different molecular weight through the modified monolithic column, the concentrated PHEMA brush was characterized and demonstrated to sharply exclude solute molecules with the critical molecular size (size-exclusion limit) comparable to the distance between the nearest-neighboring graft points d. The elution behaviors of proteins with different sizes were studied with this PHEMA-grafted column: the protein sufficiently larger than the critical size was perfectly excluded from the brush layer and separated only in the size-exclusion mode by the meso pores without affinity interaction with the brush surface. Then, the irreversible adsorption of proteins on PHEMA brushes was investigated using QCM by varying graft densities (σ = 0.007, 0.06, and 0.7 chains/nm²) and protein sizes (effective diameter = 2–13 nm). A good correlation between the protein size and the graft density was observed: proteins larger than d caused no significant irreversible adsorption on the PHEMA brushes. Thus, we experimentally substantiated the postulated size-exclusion effect of the concentrated brushes and confirmed that this effect plays an important role for suppressing protein adsorption.     

醛类的等离子体聚合Ⅰ.丁醛等离子体聚合及聚合物结构与性能

应用外部电容耦合式等离子体聚合方法,首次得到了丁醛聚合物,研究了其聚合规律,找到了较好的聚合条件。通过元素分析和红外光谱分析,证实丁醛等离子体聚合物为交联结构;电子衍射分析和X-射线衍射分析发现聚合物中存在部分结晶,而且部分以单晶形式存在;表面能测定表明丁醛等离子体聚合物为疏水性。并初步探讨了反应机理。     

Studies on Polymerization Activities by Soluble Catalysts Based on Compounds of Organotransition Metals and Aluminum Alkyls

Polymerization activities of the soluble Ziegler-type of catalyst systems, Ti(OR)₄-AlEt₃, Ti(NEt₂)₄-AlMe₃, and V(NEt₂)4-AlEt₃, were investigated. In the catalyst system of Ti(OR)₄-AlEt₃, formation of two types of Ti(III) compounds, i.e., Ti(OR)₂Et and its bridged complex with aluminum alkyl, was confirmed by IR and ESR measurements. With the addition of donor molecule to the system, it was found that the polymer yield decreased remarkably and that the bridged complex dissociated into a single or uncomplex Ti(III) paramagnetic species. It has been concluded that the bridged structure of Ti(III) species was responsible for the polymerization activity of styrene. Two reaction products of Ti(NEt₂)₃Me and Al(NEt2)Me₂ were found by NMR spectroscopic observation with the Ti(NEt₂)₄-AlMe₃ catalyst system. From the kinetic study of polymerization of styrene, it was found that Ti(NEt₂)₃Me is an active species. An anionic mechanism was proposed for the styrene polymerization by Ti(NEt₂)₃Me. In the polymerization of MMA with the V(NEt₂)₄-AlEt₃ system, a difference in the tacticity of polymer was found to depend on the polymerization conditions, e.g., AI/V ratio and temperature. From an analysis of the tacticity of the polymer, the presence of two active sites in the propagation process is suggested.     

Electrocatalysis and Amperometric Detection of Hydrogen Peroxide at an Aluminum Microelectrode Modified with Cobalt Hexacyanoferrate Film

 The electrocatalytic activity of an aluminum microelectrode modified with cobalt hexacyanoferrate film is described. A simple method was used for the preparation of the modified microelectrode. The modified microelectrode exhibits good electrocatalytic properties for electrochemical reduction of hydrogen peroxide. The effect of solution pH and applied potential on the electrocatalytic properties of the modified microelectrode is investigated. The results show that the best potential for the detection of hydrogen peroxide is 0.0 vs. SCE for better response and decrease of interferences. Due to the microelectrode scale, it can be used for the determination of small amounts of H₂O₂. The calibration plot is linear up to 1.7 mM (r = 0.988) with a response time of 5.1 s. The detection limit of the microelectrode as H₂O₂ sensor is 2 × 10⁻⁷ M. The sensivity of the H₂O₂ sensor is 225.6 nA mmol⁻¹ and RSD of this sensor is less than 2.3%. In addition, effects of possible interferences and possibility of the sensor for real samples is investigated. The present work shows the potential of the proposed method for the fabrication of modified electrodes, as it can be used to employ for different purposes in micro scale. Received June 20, 2001; accepted June 14, 2002