Relationship between sensory and instrumental analysis of 2,4,6-trichloroanisole in wine and cork stoppers

The effect of different corks stoppers on the sensory and instrumental determination of 2,4,6-trichloroanisole (TCA) was studied in wine and cork. A relationship between both measurements was also established.Four types of cork were used to seal white wine bottles for 8 months. The stoppers were from different raw material: a high quality commercial batch (C), slabs with yellow stain (YS) and slabs with a high musty and mouldy taint (T). Spiked samples (S) were prepared from C batch by injecting 1002 ng of TCA into the cork stoppers.TCA was determined by gas chromatography with electron capture detection after headspace solid phase microextraction in bottled wine (12 per group) and after extraction with pentane in the case of corks (six per group). Seven semi-trained assessors evaluated the different samples using a ranking test in 12 and six sessions for wine and cork stoppers, respectively.Wines and corks from S samples showed the highest TCA values in both sensory and instrumental measurements, the lowest values being for C samples. YS and T corks had intermediate values, although in general TCA concentration was higher in T. A slight tendency to increase the TCA content in stoppers with yellow stain compared to C samples was observed in wine. A high correlation coefficient (r=0.82) was found between sensory and instrumental analysis for wine, whereas this coefficient was much lower (r=0.56) for cork stoppers. Some hypotheses are given in order to explain these differences.     

Synthesis of thecis andtrans isomers oftert-butylaminedichloro-(dimethyl sulphoxide)platinum(II) and X-ray structure analysis of thecis compound

Summary Treatment ofcis-dichlorobis(dimethyl sulphoxide)platinum(II) [1] with an excess oftert-butylamine in MeOH yieldstert-butylamine-trans-dichloro(dimethyl sulphoxide)-platinum(II) [(tr-5)], rather than thecis-diaminechloro-(dimethyl sulphoxide)platinum(II) cation expected by analogy with similar reactions reported in the literature. The correspondingcis isomer [(cis-5)] is prepared from the same reactants (and similarly from K₂PtCl₄ andtert-butylamine) in DMSO medium, in which the initially formedtrans compound partially isomerizes to the thermodynamically favouredcis complex. The molecular structure of (cis-5) is determined by X-ray analysis. The coordination around the Pt atom is square-planar, and the DMSO ligand is S-coordinated. The lengths of the Pt-Cl bondscis andtrans to the DMSO ligand are 2.296(11) and 2.321(10) Å, respectively, and are well within expected ranges. Interatomic distances within the amine and DMSO ligands are normal.     

Conformational analysis of dimethyl(bromomethyl)- and dimethyl(iodomethyl)phosphine oxides

Conclusions The oxides of dimethyl(bromomethyl)- and dimethyl(iodomethyl)phosphines exist as equilibrium mixtures of conformer pairs in solution, the form predominating in nonpolar solvents being that in which the phosphoryl and carbon-halogen bonds are in trans orientation.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 6, pp. 1292–1296, June, 1981.     

Determination of 2,4,6-trichloroanisole and guaiacol in cork stoppers by pressurised fluid extraction and gas chromatography-mass spectrometry

This paper describes the development of an analytical method consisting of pressurised fluid extraction (PFE) and gas chromatography-mass spectrometry (GC-MS) using experimental designs to determine two volatile compounds in naturally-tainted cork stoppers. The target analytes, 2,4,6-trichloroanisole (2,4,6-TCA) and guaiacol, are involved in the cork taint of wine. First, a Plackett-Burman experimental design was carried out in order to determine the significant experimental parameters affecting the PFE process, and then a central composite design was used to optimise these significant parameters. Once the method had been optimised, the influence of the number of extraction cycles was studied. The method was applied to determine the concentration of 2,4,6-TCA and guaiacol in three cork samples, and the results were compared with the ones obtained by multiple headspace-solid-phase microextraction (MHS-SPME) and by Soxhlet extraction.     

Optimisation of a microwave-assisted extraction method for the simultaneous determination of haloanisoles and halophenols in cork stoppers

This study presents a method based on the use of microwave-assisted extraction (MAE) for the quantitative analysis of 2,4,6-trichloroanisole (TCA), 2,3,4,6-tetrachloroanisole (TeCA), pentachloroanisole (PCA), 2,4,6-tribromoanisole (TBA), 2,4,6-trichlorophenol (TCP), 2,3,4,6-tetrachlorophenol (TeCP), pentachlorophenol (PCP) and 2,4,6-tribromophenol (TBP) in cork stoppers. The influential parameters of the MAE procedure (extraction time, temperature and solvent volume) were optimised using a central composite experimental design combined with desirability functions. The optimal conditions identified were temperature 170 degrees C, solvent volume 35 mL and extraction time 90 min. MAE extracts were concentrated and derivatised prior to separation and quantification by gas chromatography with electron capture detection. To evaluate the applicability of the proposed MAE method, recovery results were compared with those obtained with the Soxhlet extraction method; the results were similar with both extraction methods. The new method was also satisfactorily applied to real cork stopper samples.     

Spectroscopic characterization of structural isomers of naphthalene: (E)- and (Z)-phenylvinylacetylene

Near-pure samples of (E)-phenylvinylacetylene ((E)-PVA) and (Z)-phenylvinylacetylene ((Z)-PVA) were synthesized, and their ultraviolet spectroscopy was studied under jet-cooled conditions. The fluorescence excitation and UV-UV holeburning (UVHB) spectra of both isomers were recorded. The S0-S1 origin of (E)-PVA occurs at 33,578 cm(-1), whereas that for (Z)-PVA occurs at 33,838 cm(-1), 260 cm(-1) above that for (E)-PVA. The present study focuses primary attention on the vibronic spectroscopy of (E)-PVA. Single vibronic level fluorescence spectra of many prominent bands in the first 1200 cm(-1) of the S0-S1 excitation spectrum of (E)-PVA were recorded, including several hot bands involving low-frequency out-of-plane vibrations. Much of the ground-state vibronic structure observed in these spectra was assigned by comparison with styrene and trans-beta-methylstyrene, assisted by calculations at the DFT B3LYP/6-311++G(d,p) level of theory. Both S0 and S1 states of (E)-PVA are shown to be planar, with intensity appearing only in even overtones of out-of-plane vibrations. Due to its longer conjugated side chain compared with that of its parent styrene, (E)-PVA supports extensive Duschinsky mixing among the four lowest-frequency out-of-plane modes (nu45-nu48), increasing the complexity of this mixing relative to that of styrene. Identification of the v' = 0-3 levels of nu48, the lowest frequency torsion, provided a means of determining the 1D torsional potential for hindered rotation about the C(ph)-C(vinyl) bond. Vibronic transitions due to (Z)-PVA were first identified as small vibronic bands that did not appear in the UVHB spectrum recorded with the hole-burn laser fixed on the S0-S1 origin of (E)-PVA. The LIF and UVHB spectra of a synthesized sample of (Z)-PVA confirmed this assignment.     

Synthesis and structural elucidation of solvent-free and solvated lithium dimethyl (HMDS) zincates

Using a co-complexation methodology the unsolvated lithium zincate [LiZn(HMDS)Me2] ( 4, HMDS = 1,1,1,3,3,3-hexamethyldisilazide) was prepared by reaction of an equimolar amount of LiHMDS with Me2Zn in a non-polar toluene-hexane solvent mixture. X-Ray crystallographic studies reveal that the asymmetric unit of 4 has a dinuclear arrangement, based on a planar LiNZnC four-membered ring. As a result of intermolecular interactions between the lithium centre of one asymmetric unit and a terminal methyl group of another, 4 presents a polymeric chain array in the solid state. DFT calculations revealed that the formation of the polymer is the driving force for the success of co-complexation of LiHMDS and Me2Zn to yield the unsolvated zincate 4. The reaction of 4 with PMDETA (N,N,N,N,N-pentamethyldiethylenetriamine) afforded the new solvated zincate [(PMDETA)Li(mu-Me)Zn(HMDS)Me] ( 5). X-Ray crystallographic studies show that the asymmetric unit of 5 consists of an open, dinuclear LiCZnC arrangement rather than a closed cyclic one, in which the HMDS ligand unusually occupies a terminal position on Zn. DFT computational studies showed that the structure found for 5 was energetically preferred to the expected HMDS-bridging isomer due to the steric hindrance imposed by the tridentate PMDETA ligand. The reaction of 4 with the neutral nitrogen donors 4-tert-butylpyridine and tert-butylcyanide afforded the homometallic compounds [(tBu-pyr)Li(HMDS)] ( 6) and [(tBuCN)Li(HMDS)] ( 7) respectively as a result of disproportionation reactions. Compounds 6 and 7 were characterized by NMR (1H, 13C and 7Li) spectroscopy.     

Determination of characteristic odorants from Harmonia axyridis beetles using in vivo solid-phase microextraction and multidimensional gas chromatography-mass spectrometry-olfactometry

Homeowners, small fruit growers, and wine makers are concerned with noxious compounds released by multicolored Asian ladybird beetles (Harmonia axyridis, Coleoptera: Coccinellidae). A new method based on headspace solid-phase microextraction (HS-SPME) coupled with multidimensional gas chromatography-mass spectrometry-olfactometry (MDGC-MS-O) system was developed for extraction, isolation and simultaneous identification of compounds responsible for the characteristic odor of live H. axyridis. Four methoxypyrazines (MPs) were identified in headspace volatiles of live H. axyridis as those responsible for the characteristic odor: 2,5-dimethyl-3-methoxypyrazine (DMMP), 2-isopropyl-3-methoxypyrazine (IPMP), 2-sec-butyl-3-methoxypyrazine (SBMP), and 2-isobutyl-3-methoxypyrazine (IBMP). To the best of our knowledge this is the first report of H. axyridis releasing DMMP and the first report of this compound being a component of the H. axyridis characteristic odor. Besides the MPs, 34 additional compounds were also identified. Quantification of three MPs (IPMP, SBMP and IBMP) emitted from live H. axyridis were performed using external calibration with HS-SPME and direct injections. A linear relationship (R(2)>0.9951 for all 3 MPs) between MS response and concentration of a standard was observed over a concentration range from 0.1 ng L(-1) to 0.05 microg L(-1) for HS-SPME-GC-MS. The method detection limits (MDL) based on multidimensional GC-MS with narrow heart-cut approach for three MPs were estimated to be between 0.020 and 0.022 ng L(-1). This represents a 38.9-52.4% improvement in sensitivity compared to GC-MS with full heart-cut method. This methodology is applicable for in vivo determination of odor-causing chemicals associated with emissions of volatiles from insects.     

Dichlorobis(2-phenylazopyridine)ruthenium(II) complexes: characterisation, spectroscopic and structural properties of four isomers

The didentate ligand 2-phenylazopyridine (azpy) can--in theory--give rise to five different isomeric complexes of the type [Ru(azpy)2Cl2], of which three have been known since 1980. The molecular structures of the cis-dichlorobis(2-phenylazopyridine) ruthenium(II) complexes alpha-[Ru(azpy)2Cl2] and beta-[Ru(azpy)2Cl2](in which the coordinating pyridine nitrogen atoms are in mutually trans and cis positions, respectively, whilst the azo nitrogen atoms are in mutually cis positions) were unambiguously determined in the early 1980s. The third isomer, gamma-[Ru(azpy)2Cl2], has for two decades, erroneously, been assumed to be the all-trans isomer. In a recent communication we have proven that for this gamma isomer the chloride ions are indeed in a trans geometry, but the pyridine nitrogen and azo nitrogen atoms of the two azpy ligands are in mutually cis geometries. In this paper the isolation of a fourth isomer is presented, the hitherto unknown delta-[Ru(azpy)2Cl2]. The isomeric structure of delta-[Ru(azpy)2Cl2] has been determined by 1H-NMR spectroscopy and single-crystal X-ray diffraction analysis, and is the all-trans isomer. The bis(azpy)-ruthenium(II) isomers are of interest because of the pronounced cytotoxicity they exhibit against tumour cell lines and could be very useful in the search for structure-activity relationships of antitumour-active ruthenium complexes, as among the isomers there is a significant difference in activity. It is of paramount importance to have a good understanding of the structural and spectroscopic properties of these complexes, which in this paper are compared and discussed, with a particular emphasis on 1D and 2D 1H NMR spectroscopies.     

Evaluation of dispersive liquid-liquid microextraction for the simultaneous determination of chlorophenols and haloanisoles in wines and cork stoppers using gas chromatography-mass spectrometry

Dispersive liquid-liquid microextraction (DLLME) coupled with gas chromatography-mass spectrometry (GC-MS) was evaluated for the simultaneous determination of five chlorophenols and seven haloanisoles in wines and cork stoppers. Parameters, such as the nature and volume of the extracting and disperser solvents, extraction time, salt addition, centrifugation time and sample volume or mass, affecting the DLLME were carefully optimized to extract and preconcentrate chlorophenols, in the form of their acetylated derivatives, and haloanisoles. In this extraction method, 1mL of acetone (disperser solvent) containing 30μL of carbon tetrachloride (extraction solvent) was rapidly injected by a syringe into 5mL of sample solution containing 200μL of acetic anhydride (derivatizing reagent) and 0.5mL of phosphate buffer solution, thereby forming a cloudy solution. After extraction, phase separation was performed by centrifugation, and a volume of 4μL of the sedimented phase was analyzed by GC-MS. The wine samples were directly used for the DLLME extraction (red wines required a 1:1 dilution with water). For cork samples, the target analytes were first extracted with pentane, the solvent was evaporated and the residue reconstituted with acetone before DLLME. The use of an internal standard (2,4-dibromoanisole) notably improved the repeatability of the procedure. Under the optimized conditions, detection limits ranged from 0.004 to 0.108ngmL(-1) in wine samples (24-220pgg(-1) in corks), depending on the compound and the sample analyzed. The enrichment factors for haloanisoles were in the 380-700-fold range.     

Thermodynamic relationship between structural isomers of the thermochromic compound bis(N-Isopropyl-5,6-benzosalicylideneiminato)nickel(II)

A pair of structural isomers was isolated at room temperature for the thermochromic nickel complex bis( N-isopropyl-5,6-benzosalicylideneiminato)nickel(II); one is a diamagnetic green form with square-planar coordination geometry (G phase), and the other is a paramagnetic brown form with a tetrahedral geometry (B phase). However, a question as to which form is thermodynamically stable was left open. To solve this problem, thermal and magnetic properties of this complex were investigated by adiabatic heat capacity calorimetry in the 6-508 K temperature range and magnetic measurements in the 2-400 K region. In addition to the two forms previously reported, two metastable crystal forms (G' and B' phases) were found. The stable phase sequence was G phase, B phase, and then liquid upon heating. The supercooled B phase gave rise to a small phase transition with nonmagnetic origin at around 50 K. By rapidly cooling the liquid, a glassy liquid state was realized below approximately 290 K. The order of thermodynamic stability at 298.15 K was revealed to be the G, B, G', and then the B' phase. The entropy, enthalpy, and Gibbs energy differences between the B and the G phases at 298.15 K were S degrees (B) - S degrees (G) = 32.8 J K (-1) mol (-1), H degrees (B) - H degrees (G) = 16.0 kJ mol (-1), and G degrees (B) - G degrees (G) = 6.25 kJ mol (-1), respectively.     

Mass-analyzed threshold ionization and structural isomers of M(3)O(4) (M = Sc, Y, and La)

M(3)O(4) (M = Sc, Y, and La) were produced in a pulsed laser-vaporization molecular beam source and studied by mass-analyzed threshold ionization (MATI) spectroscopy and electronic structure calculations. Adiabatic ionization energies (AIEs) of the neutral clusters and vibrational frequencies of the cations were measured accurately for the first time from the MATI spectra. Five possible structural isomers of M(3)O(4) were considered in the calculations and spectral analysis. A cage-like structure in C(3v) point group was identified as the most stable one. The structure is formed by fusing three M(2)O(2) fragments together, each sharing two O-M bonds with others. The ground electronic state of the neutral clusters is (2)A(1) with the unpaired electron being largely a metal-based s character. Ionization of the (2)A(1) state yields a (1)A(1) ion state in a similar geometry to the neutral cluster. The AIEs of the clusters are 4.4556 (6), 4.0586(6), and 3.4750(6) eV for M = Sc, Y, and La, respectively. The observed vibrational modes of the cations include metal-oxygen stretching, metal triangle breathing, and oxygen-metal-oxygen rocking in the frequency range of 200-800 cm(-1).     

Optimization of headspace sampling using solid‐phase microextraction for chloroanisoles in cork stoppers and gas chromatography–ion‐trap tandem mass spectrometric analysis

In a study aiming to characterize cork off‐flavour for quality control purposes, chloroanisoles were extracted and identified from cork stoppers by means of solid‐phase microextraction (SPME)–gas chromatography–ion‐trap mass spectrometry (GC–ITMS). An experimental design procedure was used to investigate the effects of some experimental parameters on the SPME of 2,4‐dichloroanisole, 2,6‐dichloroanisole, and 2,4,6‐trichloroanisole from cork stoppers by using a Carboxen‐PDMS 75 μm fibre. Variables such as extraction temperature, extraction time, and percentage of ethanol added to the matrix were optimized to improve extraction efficiency of chloroanisoles onto SPME fibre. Instrumental analysis was performed by GC–ITMS in the MS/MS mode. Preliminary analyses on standard solutions allowed selection of the appropriate ionization mode (i. e. electron impact or chemical ionization), providing for each analyte the highest instrumental response. In order to find polynomial functions describing the relationships between variables and responses, the analytical responses, i.e. the chromatographic peak areas, were processed by using the backward multiple regression analysis. For all the analytes the operating conditions providing the highest extraction yield inside the experimental domain considered were found.     

High performance liquid chromatography of structural isomers using a cyclodextrin-poly(allylamine) coated silica column

Summary High performance liquid chromatography (HPLC) separation of substituted phenols by isocratic elution was investigated using a β-cyclodextrin-bonded column. The HPLC support was prepared in-house. This support was based on silica beads coated with a β-cyclodextrin-containing poly(allylamine). The retention behavior of some substituted phenol isomers and aromatic compounds was studied. The contribution of the amino groups of the polyamine and of the β-cyclodextrin cavity to the separation process is discussed. Two retention mechanisms, inclusion complex formation and acidbase interaction, were found. The effect of the composition and pH of the mobile phase on the separation was also examined.     

Synthesis and the reversed-phase HPLC analysis ofcis andtrans-dichlorobis(ethylenediamine-ruthenium) chloride isomers

Summary In this work we report the monitoring of the synthesis ofcis andtrans-dichlorobis(ethylenedia-mine)ruthenium chloride isomers by HPLC. The preparation of thecis andtrans complexes were as described in the literature with modifications arising from reversed-phase HPLC results. Thecis andtrans complexes were separated with retention times of 3.0 min and 5.5 min respectively using an ODS column (250 mm×4.6 mm i.d. 5 μm particles, Alltech) and methanol/water 45/55 ratio as mobile phase. According to HPLC results the reaction time to completion is 48 h and not 72 h as previously described. The shorter time resulted in better yield 82% and reduced by-products.     

High performance liquid chromatography of structural isomers using a cyclodextrin-poly(allylamine) coated silica column

Summary High performance liquid chromatography (HPLC) separation of substituted phenols by isocratic elution was investigated using a β-cyclodextrin-bonded column. The HPLC support was prepared in-house. This support was based on silica beads coated with a β-cyclodextrin-containing poly(allylamine). The retention behavior of some substituted phenol isomers and aromatic compounds was studied. The contribution of the amino groups of the polyamine and of the β-cyclodextrin cavity to the separation process is discussed. Two retention mechanisms, inclusion complex formation and acidbase interaction, were found. The effect of the composition and pH of the mobile phase on the separation was also examined.     

Structure and stability of (CuNO) isomers

Quantum-mechanical calculations have been performed on various isomers of the (CuNO)⁺ system. A ²Π ground state is found for the linear CuNO⁺ and CuON⁺ isomers and a ²A′ state for the bent CuNO⁺ and CuON⁺ isomers. Energy calculations indicate that the linear CuNO⁺ structure is the most stable, the bent CuNO⁺ and CuON⁺ and the linear CuON⁺ structures are at 0.86 eV, 0.99 eV and 1.04 eV above this respectively. In the CuNO⁺ → CuON⁺ interconversion between the linear isomers, three transition states are involved, whereas the bent CuNO⁺ isomer is found to be an intermediate species. The isomerization barriers, dissociation energies, equilibrium geometries and vibration frequencies are given for all isomers in their ground and first excited states.     

Separation and identification of structural isomers by quadrupole collision-induced dissociation-hydrogen/deuterium exchange-infrared multiphoton dissociation (QCID-HDX-IRMPD)

A new approach that uses a hybrid Q-FTICR instrument and combines quadrupole collision-induced dissociation, hydrogen-deuterium exchange, and infrared multiphoton dissociation (QCID-HDX-IRMPD) has been shown to effectively separate and differentiate isomeric fragment ion structures present at the same m/z. This method was used to study protonated YAGFL-OH (free acid), YAGFL-NH₂ (amide), cyclic YAGFL, and YAGFL-OCH₃ (methyl ester). QCID-HDX of m/z 552.28 (C₂₉H₃₈N₅O₆) from YAGFL-OH reveals at least two distributions of ions corresponding to the b₅ ion and a non-C-terminal water loss ion structure. Subsequent IRMPD fragmentation of each population shows distinct fragmentation patterns, reflecting the different structures from which they arise. This contrasts with data for YAGFL-NH₂ and YAGFL-OCH₃, which do not show two distinct H/D exchange populations for the C₂₉H₃₈N₅O₆ structure formed by NH₃ and HOCH₃ loss, respectively. Relative extents of exchange for C₂₉H₃₈N₅O₆ ions from six sequence isomers (YAGFL, AGFLY, GFLYA, FLYAG, LYAGF, and LFGAY) show a sequence dependence of relative isomer abundance. Supporting action IRMPD spectroscopy data are also presented herein and also show that multiple structures are present for the C₂₉H₃₈N₅O₆ species from YAGFL-OH.