Dimensional evolution of silicon nanowires synthesized by Au–Si island-catalyzed chemical vapor deposition

This study explores the nucleation and morphological evolution of silicon nanowires (Si-NWs) on Si (0 0 1) and (1 1 1) substrates synthesized using nanoscale Au–Si island-catalyzed rapid thermal chemical vapor deposition. The Au–Si islands are formed by Au thin film (1.2–3.0 nm) deposition at room temperature followed by annealing at 700 °C, which are employed as a liquid-droplet catalysis during the growth of the Si-NWs. The Si-NWs are grown by exposing the substrates with Au–Si islands to a mixture of gasses SiH₄ and H₂. The growth temperatures and the pressures are 500–600 °C and 0.1–1.0 Torr, respectively. We found a critical thickness of the Au film for Si-NWs nucleation at a given growth condition. Also, we observed that the dimensional evolution of the NWs significantly depends on the growth pressure and temperature. The resulting NWs are 30–100 nm in diameter and 0.4–12.0 μm in length. For Si (0 0 1) substrates 80% of the NWs are aligned along the 1 1 1 direction which are 30° and 60° with respect to the substrate surface while for Si (1 1 1) most of the NWs are aligned vertically along the 1 1 1 direction. In particular, we observed that there appears to be two types of NWs; one with a straight and another with a tapered shape. The morphological and dimensional evolution of the Si-NWs is significantly related to atomic diffusion kinetics and energetics in the vapor–liquid–solid processes.     

Sol–gel synthesis of pure nano sized β-tricalcium phosphate crystalline powders

β-Tricalcium phosphate (β-TCP) nano powders (80 nm) were synthesized using a simple sol–gel route with calcium nitrate and potassium dihydrogenphosphate as calcium and phosphorus precursors, respectively. Double distilled water was used as a diluting media for β-TCP sol preparation and ammonia was used to adjust the pH. After aging, the β-TCP gel was dried at 40 °C and calcined to different temperatures ranging from 200 to 800 °C. The dried and calcined powders were characterized for phase composition using X-ray diffractrometry (XRD) and Fourier transform-infrared spectroscopy (FT-IR). The particle size and morphology was studied using Transmission electron microscopy (TEM). Calcination revealed that with increase in temperature, both the crystallinity and crystallite size of β-TCP particles increased. Particle size distribution analysis of the calcined β-TCP at 800 °C showed a narrow skewed distribution plot centered between 70 and 80 nm. This value was in closed agreement with particle size values obtained from XRD analysis (83 ± 6 nm). The present study showed that narrowly distributed, high crystalline, pure β-TCP could be obtained using this simple technique for biomedical applications.     

Epitaxial growth of highly transparent and conducting Sc-doped ZnO films on c-plane sapphire by sol–gel process without buffer

Highly transparent and conductive scandium doped zinc oxide (ZnO:Sc) films were deposited on c-plane sapphire substrates by sol–gel technique using zinc acetate dihydrate [Zn(CH₃COO)₂·2H₂O] as precursor, 2-methoxyethanol as solvent and monoethanolamine as a stabilizer. The doping with scandium is achieved by adding 0.5 wt% of scandium nitrate hexahydrate [(ScNO₃·6H₂O)] in the solution. The influence of annealing temperature (300–550 °C) on the structural, optical and electrical properties was investigated. X-ray Diffraction study revealed that highly c-axis oriented films with full-width half maximum of 0.16° are obtained at an annealing temperature of 400 °C. The surface morphology of the films was judged by SEM and AFM images which indicated formation of grains. The average transmittance was found to be above 92% in the visible region. ZnO:Sc film, annealed at 400 °C exhibited minimum resistivity of 1.91 × 10⁻⁴ Ω cm. Room-temperature photoluminescence measurements of the ZnO:Sc films annealed at 400 °C showed ultraviolet peak at 3.31eV with a FWHM of 11.2 meV, which are comparable to those found in high-quality ZnO films. Reflection high-energy electron diffraction pattern confirmed the epitaxial nature of the films even without introducing any buffer layer.     

Synthesis of nano hydroxyapatite powder that simulate teeth particle morphology and composition

A simple sol–gel precipitation technique to synthesize nano hydroxyapatite (HA) particles (30 nm) that show similar morphology, size and crystallinity to HA crystals of human teeth is reported. Calcium nitrate tetrahydrate and potassium dihydrogenphosphate were used as calcium and phosphorus precursors, respectively. Double distilled water was used as a diluting media for HA sol preparation and ammonia was used to adjust the pH to 11. After aging, the HA gel was dried at 40 °C and calcined to different temperatures ranging from 200 to 600 °C. The dried and calcined powders were characterized for phase composition using X-ray diffractrometry, and Fourier transform infra-red spectroscopy. The particle size and morphology was studied using Transmission electron microscopy. The particle size distribution analysis of HA powders showed skewed distribution plot. The phase and particle characterization studied above showed that HA calcined at 600 °C simulate HA crystals of teeth.     

Superconductivity as a Kosterlitz–Thouless transition in the two-dimensional Hubbard model

We investigate a superconducting Kosterlitz–Thouless transition in the two-dimensional (2D) Hubbard model using auxiliary quantum Monte Carlo method for the ground state. The pair susceptibility is computed for both the attractive and repulsive Hubbard model. The numerical results show that the s-wave pair susceptibility scales as χ  L² for the attractive case, in agreement with previous quantum Monte Carlo studies. The scaling χ  L² also holds for the d-wave pair susceptibility for the repulsive Hubbard model if we adjust the band parameter t′.     

Effect of the synthesis route on the structural properties and shape of the indium oxide (In2O3) nano-particles

Nano-crystalline indium oxide (In₂O₃) particles have been synthesized by sol–gel and hydro-thermal techniques. A simple hydro-alcoholic solution consisting indium nitrate hydrate and citric acid (in sol–gel method) and 1, 4-butandiol (in hydro-thermal method) have been utilized. The structural properties of indium oxide nano-powders annealed at 450 °C (for both methods) have been characterized by the X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and specific surface area (SSA) analysis. Structural analysis of the samples shows cubic phase in sol–gel and cubic-hexagonal phase mixture in hydro-thermally prepared particles. The nano-particles prepared by sol–gel method have nearly spherical shape, whereas hydro-thermally-made ones display wire- and needle-like shape in addition to the spherical shape. The obtained In₂O₃ nano-particles surface areas were 23.2 and 55.3 in sol–gel and hydro-thermal methods, respectively. The optical direct band gap of In₂O₃ nano-particles were determined to be 4.32 and 4.24 eV for sol–gel and hydro-thermal methods, respectively. These values exhibit 0.5 eV blue shift from that the bulk In₂O₃ (3.75 eV), which is related to the particle size reduction and approaching the quantum confinement limit of nano-particles.     

High-performance pyroelectric single crystals for uncooled infrared detection applications

Uncooled pyroelectric infrared detectors based on ferroelectric single crystals 0.74Pb(Mg_1/3Nb_2/3)O₃–0.26PbTiO₃ (PMN–0.26PT) were fabricated. The performances of pyroelectric detectors dependence on detector fabrication temperature, absorption layer, and element thickness were compared. The room-temperature voltage responsivity (R_v) of 200 V/W and specific detectivity (D^*) of 10⁸ cm Hz^1/2/W at 12.5 Hz have been achieved. The results reveal that the better pyroelectric response can be expected by controlling temperature below 70 °C during the fabrication of the pyroelectric detectors, selecting absorption layer with high absorption coefficient, and decreasing the thickness of the elements.     

Carbon nanotube–polymer composites for photonic devices

We report the fabrication of high optical quality single wall carbon nanotube polyvinyl alcohol composites and their application in nanotube based photonic devices. These show a broad absorption of semiconductor tubes centred at 1.55 μm, the spectral range of interest for optical communications. The films are used as mode-lockers in an erbium doped fibre laser, achieving 700 fs mode-locked pulses. Raman spectroscopy shows no damage after a long time continuous laser operation.     

Time-of-flight distributions of HD molecules abstracted at a Si(1 0 0) surface

We study the dynamics of D abstraction by 0.05 eV H atoms on a Si(1 0 0) surface. Time-of-flight (TOF) distributions of the abstracted HD molecules are measured using a quasi-random chopper/cross-correlation method. The measured TOF distribution is found to be broad and fast. The distribution is decomposed into two components being related to direct abstraction (ABS) and adsorption-induced-desorption (AID), which were revealed in the kinetics studies. The best curve fits yield mean kinetic energies of 1.15 ± 0.20 eV and 0.33 ± 0.05 eV for the ABS and AID components, respectively. Dynamics and kinetics of hydrogen abstraction at Si(1 0 0) surfaces are consistently understood.     

Nucleation, growth and morphology of Co thin films on Ag(1 1 0)

Scanning tunneling microscopy (STM) experiments reveal that Co growth on Ag(1 1 0), at coverages of Co < 1 ML and low substrate temperatures (150 K), involves a concomitant insertion of Co into the top Ag layer and exchange of Ag out onto the surface. At 300 K, coverages of Co > 1 ML gives rise to a 3D nanocluster growth on the surface, with the clusters covered by Ag. Depending slightly on coverage, the clusters have a typical diameter of 3 nm and a height of 0.4 nm. Upon annealing to 500 K, major changes are observed in the morphology of the surface. STM and AES show that there is a reduction of the number of Co islands on the surface, partly due to subsurface Co cluster migration and partly due to sintering into larger clusters.     

Nanoscale anglesite growth on the celestite (0 0 1) face

In situ atomic force microscopy (AFM) was used to study the growth behaviour of anglesite (PbSO₄) monolayers on the celestite (0 0 1) face. Growth was promoted by exposing the celestite cleavage surfaces to aqueous solutions that were supersaturated with respect to anglesite. The solution supersaturation, β_ang, was varied from 1.05 to 3.09 (where β_ang = a(Pb²⁺) · a(SO₄²⁻)/K_sp,ang). In this range of supersaturation, two single anglesite monolayers (3.5 Å in height each) from pre-existent celestite steps were grown. However, for solution supersaturation β_ang < 1.89 ± 0.06, subsequent multilayer growth is strongly inhibited. AFM observations indicate that the inhibition of a continuous layer-by-layer growth of anglesite on the celestite (0 0 1) face is due to the in-plane strain generated by the slight difference between the anglesite and celestite lattice parameters (i.e. the linear misfits are lower than 1.1%). The minimum supersaturation required to overcome the energy barrier for multilayer growth gave an estimate of the in-plane strain energy: 11.4 ± 0.6 mJ/m²_. Once this energy barrier is overcome, a multilayer Frank–Van Der Merwe epitaxial growth was observed.     

Localization and antilocalization in InSb and InAs antidot lattices

We report on the observation of localization, antilocalization and Altshuler–Aronov–Spivak (AAS) oscillations in antidot lattices patterned on high-mobility InSb/InAlSb and InAs/AlGaSb heterostructures. In addition, the antidot lattices display ballistic commensurability features. The strength of the localization peak in InSb antidot lattices decreases exponentially with temperature, with a high characteristic temperature of 25 K between 0.4 and 50 K. Analysis of the AAS oscillations enables the extraction of phase and spin coherence lengths in InAs.     

Microwave dielectric properties of (1 − x)(Mg0.95Co0.05)TiO3–x(Na0.5La0.5)TiO3 ceramic system

The microstructures and the microwave dielectric properties of the (1 − x)(Mg_0.95Co_0.05)TiO₃–x(Na_0.5La_0.5)TiO₃ ceramic system were investigated. Two-phase system was confirmed by the XRD patterns and the EDX analysis. A co-existed second phase (Mg_0.95Co_0.05)Ti₂O₅ was also detected. The microwave dielectric properties are strongly related to the density and the matrix of the specimen. A new microwave dielectric material 0.88(Mg_0.95Co_0.05)TiO₃–0.12(Na_0.5La_0.5)TiO₃, possessing an excellent combination of dielectric properties: ε_r  22.36, Q × f  110,000 GHz (at 9 GHz), τ_f  2.9 ppm/°C), is proposed as a candidate dielectric for GPS patch antennas.     

The electrodeposition of copper onto UHV-prepared GaAs(0 0 1) surfaces

Synchrotron surface X-ray diffraction has been used to investigate in situ the morphology and epitaxy of monolayer amounts of copper electrodeposited from aqueous electrolyte onto ultra-high vacuum prepared, smooth, Ga- or As-terminated GaAs(0 0 1) surfaces. The fcc lattice of the epitaxial Cu islands is rotated by 5° and tilted by about 9° with respect to the GaAs substrate lattice, leading to eight symmetry equivalent domains of Cu islands terminated by {1 1 1} facets.     

Consolidation of hydrogenation–disproportionation–desorption–recombination processed Nd–Fe–B magnets by spark plasma sintering

We have successfully consolidated hydrogenation–disproportionation–desorption–recombination (HDDR) processed Nd–Fe–Co–Zr–B–Ga powder by spark plasma sintering (SPS). The field compacted samples were sintered at different temperatures (T_S) from 550 to 600 °C with compressive pressure of 80 MPa for 20 min. Microstructural investigations by transmission electron microscopy indicated that the sintered specimen exhibits Nd₂Fe₁₄B grains of ~300 nm with Nd-rich grain boundary phase. The optimum magnetic properties of B_r: 1.22 T, H_c: 928 kA/m, _BH_c: 600 kA/m, (BH)_max: 210 kJ/m³ were obtained in the sample sintered at 550 °C. The strategy for further improving the coercivity and remanence is discussed based on the microstructure-property relationships.     

Misfit driven azimuthal orientation of NaCl domains on Ag(1 0 0)

We investigated the growth of thin NaCl films on Ag(1 0 0) by spot-profile-analysis low energy electron diffraction (SPA-LEED), varying extensively the growth temperature (200–500 K) and the film thickness (0.5–14 ML). The incommensurate growth of NaCl on Ag(1 0 0) yields (1 0 0)-terminated epitaxial NaCl domains, which are preferentially oriented with their [0 1 0] axis parallel to that of the substrate. At 300 K, the NaCl domains exhibit an azimuthal mosaicity by 14° around this orientation and the NaCl unit cell is laterally contracted in the first layers by 0.9% with respect to the bulk. At higher growth temperatures, the azimuthal mosaic distribution sharpens and additional distinct orientations appear, presumably due to a higher-order commensurability. The evolution of the azimuthal mosaic distribution with increasing temperature can be ascribed to both the NaCl thermal expansion and higher diffusion rates of NaCl on Ag(1 0 0). The best epitaxy, i.e. that with the highest selectivity of a specific azimuthal domain orientation, is achieved by growing NaCl films at low deposition rate (0.1 ML min⁻¹) on the Ag(1 0 0) substrate at constant high temperature (450–500 K). The observations made here can probably be applied more generally to other heterogeneous interfaces and, in particular, be used to improve the quality of thin insulating films.     

From Zn microspheres to hollow ZnO microspheres: A simple route to the growth of large scale metallic Zn microspheres and hollow ZnO microspheres

Large scale metallic Zn microspheres and hollow ZnO microspheres are synthesized by thermal evaporation and vapor transport by heating a ZnO/graphite mixture at 1000 °C. Firstly, metallic Zn microspheres are fabricated with diameters in the range of 1–10 μm. The Zn microspheres are then annealed at 600 °C in air, which form hollow semiconducting ZnO microspheres. EDX and XRD spectra reveal that the oxidized material is indeed ZnO. Room temperature photoluminescence spectra of the oxidized material show a sharp peak at 380 nm and a wider broad peak centered at 490 nm. This growth mechanism is discussed and further investigated for other metallic and metal oxide microstructures.     

Bödeker’s effective theory: From Langevin dynamics to Dyson–Schwinger equations

The dynamics of weakly coupled, non-abelian gauge fields at high temperature is non-perturbative if the characteristic momentum scale is of order |k|g²T. Such a situation is typical for the processes of electroweak baryon number violation in the early Universe. Bödeker has derived an effective theory that describes the dynamics of the soft field modes by means of a Langevin equation. This effective theory has been used for lattice calculations so far [G.D. Moore, Nucl. Phys. B568 (2000) 367. Available from: <hep-ph/9810313>; G.D. Moore, Phys. Rev. D62 (2000) 085011. Available from: <hep-ph/0001216>]. In this work we provide a complementary, more analytic approach based on Dyson–Schwinger equations. Using methods known from stochastic quantitation, we recast Bödeker’s Langevin equation in the form of a field theoretic path integral. We introduce gauge ghosts in order to help control possible gauge artefacts that might appear after truncation, and which leads to a BRST symmetric formulation and to corresponding Ward identities. A second set of Ward identities, reflecting the origin of the theory in a stochastic differential equation, is also obtained. Finally, Dyson–Schwinger equations are derived.     

Laser gain by electron collisional pumping of Ar VII–V XII

Gain coefficients have been calculated for transitions of singlet levels ns–np of orbital n=4 and n=5 in magnesium-like ions with atomic numbers Z=18, 19, 20, 21, 22 and 23. Population inversions for 4p and 5p levels in these ions were also calculated, via electron collisional excitation, for electron temperature range of 93–231 eV and electron density range of 10¹⁶–10¹⁷ cm⁻³. Under these plasma conditions, the maximum gain that occurred for 4s–4p transition was at electron temperature of 231 eV and electron density of 4×10¹⁷ cm⁻³. Scaling of the maximum gain coefficients with atomic number Z and the plasma parameters is also presented.     

Quantum confinement and interface structure of Si nanocrystals of sizes 3–5 nm embedded in a-SiO2

Spectroscopic ellipsometry and Monte Carlo simulations are employed to answer the fundamental question whether the energy gaps of Si nanocrystals with sizes in the range of 3–5 nm, which are embedded in amorphous silica, follow or deviate from the quantum confinement model, and to examine their interfacial structure. It is shown that the optical properties of these nanocrystals are well described by the Forouhi–Bloomer interband model. Analysis of the optical measurements over a photon-energy range of 1.5–5 eV shows that the gap of embedded nanocrystals with a mean size of 3.9 nm follows closely quantum confinement theory. A large band gap expansion (0.65 eV) compared to bulk Si is observed. The Monte Carlo simulations reveal a non-abrupt interface and a large fraction of interface oxygen bonds. This, in conjunction with the experimental observations, indicates that oxygen states and the chemical disorder at the interface have a negligible influence on the optical properties of the material in this size regime.