Spherical Sn–Ni–C alloy anode material with submicro/micro complex particle structure for lithium secondary batteries

Submicro/micro-scaled spherical Sn–Ni–C alloy powders synthesized from oxides of Sn and Ni via carbothermal reduction at 900 °C were examined for use as anode materials in Li-ion battery. The synthesized spherical Sn–Ni–C particles show a loose micro-sized structure and a multi-phase composition. The reaction product carbon oxide gases yielded in the carbothermal reduction process should be responsible to the loose structure characteristics of Sn–Ni–C particles. The prepared Sn–Ni–C alloy composite electrode exhibits a stable reversible capacity of 310 mA h g⁻¹ at constant current density of 100 mA g⁻¹, and can be retained at 290 mA h g⁻¹ after 25 cycles. The space existing in loose particle can accommodate the large volume changes during charge/discharge cycling. The ductile component Ni plays as a buffer to relieve the mechanical stress induced by the large volume changes upon cycling. The remained carbon can prevent the aggregation between small alloy particles. All these factors contribute greatly to the excellent cycling stability of Sn–Ni–C alloy electrode. This carbothermal reduction method is simple, cheap and mass-productive, thus suitable to large scale production of alloy anode powders used for lithium ion batteries.     

Direct electrochemistry of hemoglobin and its electrocatalytic effect based on its direct immobilization on carbon ionic liquid electrode

Direct electrochemistry of hemoglobin (Hb) has been achieved by its direct immobilization on carbon ionic liquid electrode (CILE). CILE was immersed in a solution containing Hb and ionic liquid, octylpyridinium chloride ([OcPy][Cl]), to directly immobilize Hb on CILE. Cyclic voltammetry of modified electrode exhibited quasi-reversible peaks corresponding to Hb. The oxidation and reduction peak potentials of immobilized Hb in acetate buffer solution, pH 5.0 and at a scan rate of 0.1 V s⁻¹ were obtained at about –150 mV and –290 mV, respectively. The average surface coverage of the electroactive Hb adsorbed on the electrode surface was calculated as 8.4 × 10⁻¹¹ mol cm⁻². Hb retained its bioactivity on modified electrode and showed excellent electrocatalytic activity towards oxygen, hydrogen peroxide and nitrite. Hydrogen peroxide can be determined in the range of 1.0 × 10⁻⁴–5.0 × 10⁻³ M.     

Myoglobin immobilized on Fe3O4@SiO2 magnetic nanoparticles: Direct electron transfer,enhanced thermostability and electroactivity

Myoglobin (Mb) has been successfully immobilized in alternation with oppositely charged poly(dimethyldiallylammonium chloride) via the sequential layering approach on the biocompatible Fe₃O₄@SiO₂ nanoparticles. The bound Mb could be easily separated by an external magnetic field and used as less costly, more stable, and reusable alternatives to the soluble ones. Direct electron transfer between the immobilized Mb and the electrode was observed. Moreover, the immobilized Mb provided remarkable thermostability up to 70 °C and high electroactivity with the apparent Michaelis–Menten constant (k_M) of 45 μM.     

Direct electron transfer of cytochrome c and its biosensor based on gold nanoparticles/room temperature ionic liquid/carbon nanotubes composite film

A robust and effective composite film based on gold nanoparticles (GNPs)/room temperature ionic liquid (RTIL)/multi-wall carbon nanotubes (MWNTs) modified glassy carbon (GC) electrode was prepared by a layer-by-layer self-assembly technique. Cytochrome c (Cyt c) was successfully immobilized on the RTIL-nanohybrid film modified GC electrode by electrostatic adsorption. Direct electrochemistry and electrocatalysis of Cyt c were investigated. The results suggested that Cyt c could be tightly adsorbed on the modified electrode. A pair of well-defined quasi-reversible redox peaks of Cyt c was obtained in 0.10 M, pH 7.0 phosphate buffer solution (PBS). RTIL-nanohybrid film showed an obvious promotion for the direct electron transfer between Cyt c and the underlying electrode. The immobilized Cyt c exhibited an excellent electrocatalytic activity towards the reduction of H₂O₂. The catalysis currents increased linearly to the H₂O₂ concentration in a wide range of 5.0 × 10⁻⁵– 1.15 × 10⁻³ M. Based on the multilayer film, the third-generation biosensor could be constructed for the determination of H₂O₂.     

Noncovalent assembly of ferrocene on modified gold surfaces mediated by uracil–adenine base pairs

Redox-active ferrocene was assembled on gold surfaces through the hydrogen bonding interactions between adenine-substituted ferrocene and a uracil-terminated organothiol monolayer. The surface coverage of ferrocene Γ could be varied from ca. 4 × 10^? 11 to 2.0 × 10^? 10 mol cm^? 2 by diluting the thiol-modified uracil derivative with inert 1-octanethiol. A decrease in the apparent electron transfer rate constant for ferrocene, k_app, from ca. 50 to 10 s^? 1 was observed upon increasing Γ.     

A biofuel cell with enhanced power output by grape juice

Glucose oxidase and laccase immobilized at multiwalled carbon nanotubes-ionic liquid gel modified electrodes are used as the catalysts of anode and cathode of biofuel cells (BFCs), respectively. The BFC based on glucose and air is proposed. When ferrocene monocarboxylic acid is adopted as the mediator of anode, the power output of the BFC is ca. 4.1 μW (power density ca. 10.0 μW cm⁻²), which is higher than the value of 2.7 μW (power density ca. 6.6 μW cm⁻²) by taking ferrocene dicarboxylic acid as the mediator. This implies that the mediator with formal potential closing to that of the enzyme does improve the power output. Furthermore, the power output of the BFC is greatly improved by taking grape juice as the fuel of anode rather than glucose. This system also indicates that grape juice as a fuel of the BFC not only is feasible and can also enhances the power output of the BFCs. Besides, it greatly lowers the cost and simplifies the preparation procedure of the BFCs, making the BFC towards “green” bioenergy.     

Bismuth nanosheets grown on carbon fiber cloth as advanced binder-free anode for sodium-ion batteries

The bismuth nanosheets grown on carbon fiber cloth were designed. For sodium-ion batteries, the Bi/CFC electrode exhibited a high reversible capacity of 350 and 240 mAh g^− 1 after 300 cycles at 50 and 200 mA g^− 1, as well as a good rate capability. Besides, the electrode displayed two flat potential profiles during the charge/discharge process. The results suggest that the Bi/CFC electrode has excellent potential as an anode for sodium-ion batteries.     

Microstructure changes to iron nanoparticles during discharge/charge cycles

Iron nanoparticles that were synthesized by chemical reduction were used as the active material at the electrode, followed by measurement of their capacity during discharge/charge cycles. The discharge capacity of the first cycle was extremely high, 510 mAh/g-Fe, at a current density of 200 mA/g-Fe, indicating a marked increase in the capacity and the output current of iron electrodes when nanoparticles of iron, instead of micron-sized particles were used as the active materials. However, this capacity deteriorated rapidly during the discharge/charge cycles, while the size of iron nanoparticles increased, suggesting that the dissolution and re-crystallization of iron could have occurred during these cycles. A good correlation was found between the capacities and the surface areas of iron nanoparticles following each cycle. Our result further demonstrated that the capacity depends only on the surface area of iron particles, varying by 30 mAh with every 1 m² of iron.     

A small angle neutron scattering study of the interface between solids and oil-continuous emulsions and oil-based microemulsions

We have measured the small angle neutron scattering (SANS) from slurries of powder in contact with surfactant solutions and emulsions to determine the fluid/solid interfacial structure. The slurry solids consisted either of graphite or pyrites particles; and the fluids were hexadecane containing the robust commercial polyisobutylenesuccinamide (PIBSA) surfactant, or a high internal phase emulsion of aqueous ammonium nitrate in hexadecane stabilised by PIBSA. To resolve the interfacial structure for both systems, combinations of deuterated and protonated materials were used.At low concentration in hexadecane, PIBSA forms a complete monolayer on graphite with a footprint per molecule of 103 Å² and a layer thickness of 19 Å. At higher concentrations, the complete monolayer of footprint is 61 Å² and 30 Å thick indicating compression of the PIBSA chain coil structure. Geometric exclusion effects caused by the stacking of the graphite particles also results in an excess of oil for ca. 160 Å above the surfactant monolayer.For pyrites in contact with surfactant in hexadecane, the oxidised surface layer, while smooth at the oil interface, is diffuse and/or rough at the interface with the bulk sulphide below. There is again a complete monolayer of surfactant adsorbed at the oxide surface, in a relatively compressed state with a footprint of 70 Å², more tightly bound than on graphite. The excess of oil phase above the adsorbed surfactant monolayer is observed for samples with larger pyrites particle sizes but not for a sample with smaller particles. This suggests that the oil excess does arise from purely geometric solid particle packing, but that the local particle surface curvatures are significantly higher than the overall particle size would suggest.The scattering from the pyrites/emulsion interface was modelled by a 30 Å thick monolayer of surfactant coating an oxide surface with a molecular footprint of 123 Å². For the larger particle size samples, there is a 30 Å thick layer of oil above the pyrites particle surface before a bulk emulsion/pyrites mixture is reached.These results extend previous reflectometry experiments on the silicon/emulsion interface, indicating that for stable emulsions the structures are qualitatively similar for three dissimilar solid surfaces. They show that useful results on surfactant structure and emulsion layering at the solid/emulsion and other solid/fluid interfaces can be simply obtained by SANS on powder samples variously contrasted by deuteration. SANS can be applied to a much greater range of solid interfaces than reflectometry since large neutron-transparent single crystals are not required, although the variety of faces in a powdered material degrades the quality of the information.     

Improvement in performance of a flow electrochemical sensor by using carbamoyl-arms polyazamacrocycle for the preconcentration of lead ions onto the electrode

A flow electrochemical sensor for trace analysis of lead, using TETRAM-modified graphite felt electrode is reported here. TETRAM ligands are covalently immobilized on the graphite felt by chemical reactions on amino acid linkers, previously attached to the electrode by an electrochemical process. The detection is performed in two steps: the preconcentration of Pb²⁺ ions by complexation with immobilized TETRAM and the analysis by linear sweep stripping voltammetry. A calibration curve typical of at least two equilibrium processes is obtained. A limit of detection of 2.5 × 10^?8 mol L^?1 is reached for a total analysis time of 35 min. Interestingly, the flow sensor shows a good selectivity toward lead in presence of Cu²⁺, Cd²⁺, Ni²⁺, Zn²⁺ and Co²⁺ ions. This new sensor exhibits improved sensitivity and selectivity compared to the previously reported sensor using cyclam-modified electrode. It is stable after three uses, using strong acidic medium for the regeneration step.     

Improved direct electron transfer and electrocatalytic activity of horseradish peroxidase immobilized on gemini surfactant–polyvinyl alcohol composite film

The voltammetric and electrocatalytic behavior of horseradish peroxidase (HRP) immobilized on a cationic gemini surfactant (i.e. C₁₂H₂₅N(CH₃)₂–C₁₂H₂₄–N(CH₃)₂C₁₂H₂₅Br₂, C₁₂–C₁₂–C₁₂)–polyvinyl alcohol (PVA) composite film-coated glassy carbon electrode (GCE) has been studied. It is found that on the novel composite film HRP presents excellent electroactivity and can exhibit a pair of well-defined voltammetric peaks in 0.10 M pH 7.0 phosphate buffer solution (PBS). The immobilized HRP also presents good bioelectrocatalytic activity, and it can catalyze the reduction of oxygen (O₂), hydrogen peroxide (H₂O₂), nitrite ion (NO₂^?) and trichloroacetic acid (TCA). For H₂O₂ the catalytic current is linear to its concentration in the range of 0.195–97.5 μM, and the detection limit is down to 6.5 × 10^?8 M. The response shows Michaelis–Menten feature and the apparent Michaelis–Menten constant is estimated to be 110.5 μM. Similarly, the electrode can sense NO₂^? and TCA. In addition, it is observed that the spacer group of gemini surfactant affects the electroactivity of HRP significantly. A spacer group with higher flexibility and hydrophility is favorable to the electron transfer of HRP. UV–vis spectrum indicates that the structure of HRP in the PVA–C₁₂–C₁₂–C₁₂ film is similar to that of native HRP. Thus the C₁₂–C₁₂–C₁₂–PVA composite possesses good biocompatibility and has promising application in fabricating biosensor and bioelectronics.     

Chemical vapor generation of silver for atomic absorption spectrometry with the multiatomizer: Radiotracer efficiency study and characterization of silver species

Volatile Ag species were generated in flow injection arrangement from nitric acid environment in the presence of surfactants (Triton X-100 and Antifoam B) and permanent Pd deposits as the reaction modifiers. Atomic absorption spectrometry (AAS) with multiple microflame quartz tube atomizer heated to 900 °C was used for atomization; evidence was found for thermal mechanism of atomization. Relative and absolute limits of detection (3σ, 250 μl sample loop) measured under optimized conditions were: 1.4 μg l^? 1 and 0.35 ng, respectively.The efficiency of chemical vapor generation (CVG) as well as spatial distribution of residual analyte in the apparatus was studied by ¹¹¹Ag radioactive indicator (half-life 7.45 days) of high specific activity. It was found out that 23% of analyte was released into the gaseous phase. However, only 8% was found on filters placed at the entrance to the atomizer due to transport losses. About 40% of analyte remained in waste liquid, whereas the rest was found deposited over the CVG system.Presented study follows the hypothesis that the “volatile” Ag species are actually metallic nanoparticles formed upon reduction in liquid phase and then released with good efficiency to the gaseous phase. Number/charge size distributions of dry aerosol were determined by Scanning Mobility Particle Sizer. Ag was detected in 40–45 nm particles holding 10 times more charge if compared to Boltzmann equilibrium. At the same time, Ag was also present on 150 nm particles, the main size mode of the CVG generator. The increase of Ag in standards was reflected by proportional increase in particle number/charge for 40–45 nm size particles only.Transmission electron microscopy revealed particles of 8 ± 2 nm sampled from the gaseous phase, which were associated in isolated clusters of few to few tens of nanometres. Ag presence in those particles was confirmed by Energy Dispersive X-ray Spectroscopy (EDS) analysis.     

Gold sputtered electrode surfaces enhance direct electron transfer reactions of human cytochrome P450s

We immobilized human cytochrome P450 (CYP), a membrane-bound enzyme, onto both smooth and nanostructured surfaces of gold electrodes via a naphthalene thiolate monolayer film. Rapid electron transfer of CYP with an electrode as a redox partner took place when the enzyme was immobilized onto an electrode surface with nanostructures. This structure was easily prepared by conventional sputtering techniques. A well-defined pair of peaks was observed at ? 0.175 V (vs. SHE) with the largest heterogeneous electron transfer rate constant of 340 s^? 1 for human CYP. The positive redox potential shift of 45 mV upon drug (testosterone) binding was clearly detected, which corresponded to a change in the spin states of heme iron in CYP. The present study showed that gold sputtered surfaces are very useful for direct electron transfer reactions of human CYP isoforms.     

Positive shift of the potential of zero total charge of stepped Pt(1 1 1) electrodes decorated by irreversibly adsorbed bismuth

The value of the potential of zero total charge (pztc) of stepped Pt(1 1 1) electrodes, whose step sites have been blocked by irreversibly adsorbed bismuth, has been determined by means of the CO displacement experiment. It has been observed that the pztc of the decorated surfaces shift positively with respect to that of the substrate stepped surface electrode. In this way the electrode total charge at constant potential diminishes by effect of the adatom adsorption. The oxidation of adsorbed CO takes place at higher potentials on the decorated surfaces, pointing out a direct effect of the pztc shift on their reactivity as electrocatalyzers.     

Fabrication and electrochemical properties of the Sn–Ni–P alloy rods array electrode for lithium-ion batteries

A new ternary Sn–Ni–P alloy rods array electrode for lithium-ion batteries is synthesized by electrodeposition with a Cu nanorods array structured foil as current collector. The Cu nanorods array foil is fabricated by heat treatment and electrochemical reduction of Cu(OH)₂ nanorods film, which is grown directly on Cu substrate through an oxidation method. The Sn–Ni–P alloy rods array electrode is mainly composed of pure Sn, Ni₃Sn₄ and Ni–P phases. The electrochemical experimental results illustrate that the Sn–Ni–P alloy rods array electrode has high reversible capacity and excellent coulombic efficiency, with an initial discharge capacity and charge capacity of 785.0 mAh g^?1 and 567.8 mAh g^?1, respectively. After the 100th discharge–charge cycling, capacity retention is 94.2% with a value of 534.8 mAh g^?1. The electrode also performs with an excellent rate capacity.     

Ferrocene-modified Fe3O4@SiO2 magnetic nanoparticles as building blocks for construction of reagentless enzyme-based biosensors

A novel amperometric glucose biosensor was developed by entrapping glucose oxidase (GOD) in chitosan (CS) composite doped with ferrocene monocarboxylic acid-modified magnetic core-shell Fe₃O₄@SiO₂ nanoparticles (FMC-AFSNPs). It is shown that the obtained magnetic bio-nanoparticles attached to the surface of a carbon paste electrode (CPE) with the employment of a permanent magnet showed excellent electrochemical characteristics and at the same time acted as mediator to transfer electrons between the enzyme and the electrode. Under optimal conditions, this biosensor was able to detect glucose in the linear range from 1.0 × 10⁻⁵ to 4.0 × 10⁻³ M with a detection limit of 3.2 μM (S/N = 3). This immobilization approach effectively improved the stability of the electron transfer mediator and is promising for construction of biosensor and bioelectronic devices.     

Electro-reduction of cuprous chloride powder to copper nanoparticles in an ionic liquid

Cyclic voltammetry of the CuCl powder in a cavity microelectrode revealed direct electro-reduction in solid state in 1-butyl-3-methylimidazolium hexafluorophosphate. Potentiostatic electrolysis of the salt powder (attached to a current collector) in the ionic liquid produced Cu nanoparticles as confirmed by X-ray diffraction, energy dispersive X-ray analysis, scanning and transmission electron microscopy. The particle size decreased down to 10 nm when the electrode potential was shifted from −0.9 V to −1.8 V (versus Ag/Ag⁺). The electro-reduction and the nanoparticle formation mechanisms were investigated in the ionic liquid and also in aqueous 0.1 mol L⁻¹ KClO₄ in which larger Cu particles were obtained.     

Platinum-macrocycle co-catalyst for electro-oxidation of formic acid

In this work, a new promoter, tetrasulfophthalocyanine (FeTSPc), one kind of environmental friendly material, was found to be very effective in both inhibiting self-poisoning and improving the intrinsic catalysis activity, consequently enhancing the electro-oxidation current during the electro-oxidation of formic acid. The cyclic voltammograms test showed that the formic acid oxidation peak current density has been increased about 10 times compared with that of the Pt electrode without FeTSPc. The electrochemical double potential step chronoamperometry measurements revealed that the apparent activity energy decreases from 20.64 kJ mol⁻¹ to 17.38 kJ mol⁻¹ after Pt electrode promoted by FeTSPc. The promoting effect of FeTSPc may be owed to the specific structure and abundant electrons of FeTSPc resulting in both the steric hindrance of the formation of poisoning species (CO) and intrinsic kinetic enhancement. In the single cell test, the performance of DFAFC increased from 80 mW cm⁻² mg⁻¹ (Pt) to 130 mW cm⁻² mg⁻¹ after the anode electrode adsorbed FeTSPc.     

Fabrication and electrochemical characterization of interdigitated nanoelectrode arrays

Interdigitated nanoelectrode arrays with controlled electrode bandwidth and gap geometries ranging from 30 nm to 1 μm were fabricated on glass substrates by a planar process involving high resolution electron beam lithography and lift-off, and their characteristic electrochemical responses to an aqueous ferrocene derivative solution were examined using fundamental electrochemical techniques. Despite the comparatively large electrode area of electrode arrays containing 10 bands to a single band electrode, quasi-steady-state currents with high current density were obtained at a slow potential sweep rate in cyclic voltammograms of ferrocene derivative since the lateral dimension of the nanoelectrode arrays was considerably less than the scale of the diffusion layer of redox species. Additionally, it was demonstrated that the electrode thickness influenced limiting currents of voltammograms in the case of nanoelectrode arrays. In generation-collection mode experiments, furthermore, a collection efficiency as high as ∼99% was attained by 100 nm wide electrode arrays with a gap dimension of 30 nm.     

Silver particle-decorated carbon paste electrode based on ionic liquid for improved determination of nitrite

A simple silver particle-modified carbon paste electrode is proposed for the determination of low concentration levels of nitrite ions. The electrode consists of a carbon powder decorated with silver sub-micrometre particles (AgPs) and a hydrophobic ionic liquid trihexyltetradecylphosphonium chloride as a binder. It has been shown that AgPs exhibit a strong electrocatalytic effect on the nitrite oxidation. For optimal electroanalytical performance the electrode was conditioned via silver oxidation/reduction cycle. The electrode revealed a linear square-wave voltammetric response in a wide examined concentration range of 0.05 to 1.0 mmol L^− 1, limit of detection (LOD) of 3 μmol L^− 1 and excellent repeatability with RSD of 0.3%.