Fabrication and Use of Dual‐function Iridium Oxide Coated Gold SECM Tips. An Application to pH Monitoring above a Copper Electrode Surface during Nitrate Reduction.

The fabrication of a gold microelectrode modified with iridium oxide film (IrO_x) and its use as tip with a dual function in SECM experiments is reported. The defective structure of the coating onto the microelectrode surface was used as strategy to combine the advantages of both amperometric (for current‐distance determination) and potentiometric (for pH sensing) SECM operation modes. Approach curves, using oxygen and hexaammineruthenium(III) as redox mediators, were obtained without significant loss of the performance and reproducibility of the potentiometric pH response. This allowed the precise positioning of the proposed tip above a substrate in SECM experiments and, subsequently, to monitor pH at the substrate surface. The IrO_x modified microelectrode was applied successfully in SECM experiments involving the local proton consumption during the nitrate reduction at a copper cathode surface.     

Non‐destructive Patterning of Carbon Electrodes by Using the Direct Mode of Scanning Electrochemical Microscopy

Patterning of glassy carbon surfaces grafted with a layer of nitrophenyl moieties was achieved by using the direct mode of scanning electrochemical microscopy (SECM) to locally reduce the nitro groups to hydroxylamine and amino functionalities. SECM and atomic force microscopy (AFM) revealed that potentiostatic pulses applied to the working electrode lead to local destruction of the glassy carbon surface, most likely caused by etchants generated at the positioned SECM tip used as the counter electrode. By applying galvanostatic pulses, and thus, limiting the current during structuring, corrosion of the carbon surface was substantially suppressed. After galvanostatic patterning, unambiguous proof of the formation of the anticipated amino moieties was possible by modulation of the pH value during the feedback mode of SECM imaging. This patterning strategy is suitable for the further bio‐modification of microstructured surfaces. Alkaline phosphatase, as a model enzyme, was locally bound to the modified areas, thus showing that the technique can be used for the development of protein microarrays.     

Accurately measuring respiratory activity of single living cells by scanning electrochemical microscopy

Scanning electrochemical microscopy (SECM) is a powerful tool to examine the respiratory activity of living cells. However, in SECM measurements of cell respiratory activity, the signal recorded usually also includes the signal corresponding to the cell topography. Therefore, measurements of cell respiratory activity using conventional SECM techniques are not accurate. In the present work, we develop a method for accurate measurement of the respiratory activity of single living cells using SECM. First, cells are immobilized on a glass substrate modified with collagen. Then, a Pt ultramicroelectrode tip of SECM held at −0.50 V is scanned along the central line across a living cell and a SECM scan curve, i.e., the relationship of the tip current versus the displacement (the first scan curve) is recorded with a negative peak. The peak current i_p on this first scan curve is composed of i_p1, which corresponds to the cell respiratory activity and i_p2, which corresponds to the cell topography. In order to isolate the i_p2 component, the cell is killed by exposing it to 1.0 × 10⁻³ mol/L KCN for 10 min. The tip is then scanned again with the same trace over the dead cell, and a second SECM scan curve is recorded. Noting that the topography of the dead cell is the same as that of the living cell, this second scan curve with a negative peak corresponds now only to the cell topography. Thus, i_p2 is obtained from the second SECM scan curve. Finally, i_p1 corresponding to the respiratory activity of the living cell can be accurately calculated using i_p1 = i_p − i_p2. This method can be used to monitor real-time change in the respiratory activity of single cells after exposing them to KBr, NaN₃ and KCN.     

Scanning electrochemical microscopy study of ion transfer process across water/2-nitrophenyloctylether interface supported by hydrophobic carbon ceramic electrode

A carbon ceramic electrode (CCE) modified with the redox probe—decamethylferrocene solution in hydrophobic organic solvent—2-nitrophenyloctyl ether and immersed into an aqueous solution was studied by scanning electrochemical microscopy (SECM). After the electrochemical oxidation of decamethylferrocene, its cations were detected near the electrode surface in the aqueous phase. This indicates that some fraction of the redox-active cations electrochemically produced in the organic phase is transferred across the liquid/liquid interface. They are reduced at the SECM tip and form a solid deposit. The amount of deposited decamethylferrocene was estimated by the anodic reaction at the tip. It is affected by the substrate–tip distance, deposition time, and electrolyte concentration. The SECM images of unmodified and modified CCEs are consistent with their heterogeneous structure.     

Surface patterning using scanning electrochemical microscopy to locally trigger a “click” chemistry reaction

We report on the surface micropatterning of conductive surfaces via the electrochemical triggering of a click reaction, the copper(I) catalyzed azide–alkyne cycloaddition reaction (CuAAC) by SECM via a two-step approach: (i) functionalization on the entire surface with azido-aryl groups by using the diazonium approach followed by (ii) the covalent linkage of alkyne-bearing ferrocene by CuAAC within a local area by SECM. More precisely, the click reaction was triggered by Cu(I) catalyst generation for 30 min at the SECM tip positioned ≈ 10 μm above the azido-aryl modified surface. The dimension of the spot obtained under these conditions was ≈ 75 μm. The electrochemical imaging by SECM of the ultra thin area locally clicked with ferrocene moieties was made thanks to the electrocatalytic properties of the ferrocene modified surface towards ferrocyanide electrooxidation. This local clicking procedure opens the gate to further controlled functionalization of restricted small substrates.     

In situ scanning electrochemical microscopy (SECM) detection of metal dissolution during zinc corrosion by means of mercury sphere-cap microelectrode tips

This work presents a scanning electrochemical microscopy (SECM)-based in situ corrosion probing methodology that is capable of monitoring the release of zinc species in corrosion processes. It is based on the use of Hg-coated Pt microelectrodes as SECM tips, which offer a wider negative potential range than bare platinum or other noble-metal tips. This allows for the reduction of zinc ions at the tip to be investigated with low interference from hydrogen evolution and oxygen reduction from aqueous solutions. The processes involved in the corrosion of zinc during its immersion in chloride-containing solutions were successfully monitored by scanning the SECM tip, set at an adequate potential, across the sample either in one direction or in the X-Y plane parallel to its surface. In this way, it was possible to detect the anodic and cathodic sites at which the dissolution of zinc and the reduction of oxygen occurred, respectively. Additionally, cyclic voltammetry (CV) or constant potential measurements were used to monitor the release of zinc species collected at the tip during an SECM scan.     

Study of the effects of hydrogen on the pitting processes of X70 carbon steel with SECM

The effects of hydrogen on the pitting processes of X70 carbon steel in neutral chloride ions containing solution are investigated by using the scanning electrochemical microscope (SECM) technique. The tip of the SECM monitors the Fe²⁺ ions produced by the specimen during its anodic dissolution processes, thus the initiation and the propagation of the pitting processes can be observed. Pitting is much more easily observed after the specimen has been pre-charged with hydrogen, for the oxidation of the hydrogen in the X70 decreases the pH value at the X70/solution interface, which retards the formation of an oxide film and subsequently promotes the pitting processes. The observed behaviour is further verified by the decrease of the solution's pH.     

Analysis of diffusion-controlled stochastic events of iridium oxide single nanoparticle collisions by scanning electrochemical microscopy

We investigated the electrochemical detection of single iridium oxide nanoparticle (IrO(x) NP) collisions at the NaBH(4)-treated Pt ultramicroelectrode (UME) in a scanning electrochemical microscope (SECM) over an insulating surface. The NP collision events were monitored by observing the electrocatalytic water oxidation reaction at potentials where it does not take place on the Pt UME. These collisions occurred stochastically, resulting in a transient response ("blip") for each collision. The frequency of the collisions is proportional to the flux of NPs to the UME tip, and thus equivalent to the SECM current. A plot of collision frequency versus distance followed the theoretical approach curve behavior for negative feedback for a high concentration of mediator, demonstrating that the collisions were diffusion-controlled and that single-particle measurements of mass transport are equivalent to ensemble ones. When the SECM was operated with a Pt substrate at the same potential as the tip, the behavior followed that expected of the shielding mode. These studies and additional ones result in a model where the IrO(x) NP collision on the Pt UME is adsorptive, with oxygen produced by the catalyzed water oxidation causing a current decay. This results in a blip current response, with the current decay diminished in the presence of the oxygen scavenger, sulfite ion. Random walk and theoretical bulk simulations agreed with the proposed mechanism of IrO(x) NP collision, adsorption, and subsequent deactivation.     

Fabricating and imaging carbon-fiber immobilized enzyme ultramicroelectrodes with scanning electrochemical microscopy.

The scanning electrochemical microscope (SECM) is used to image the activity of enzymes immobilized on the surfaces of disk-shaped carbon-fiber electrodes. SECM was used to map the concentration of enzymatically produced hydroquinone or hydrogen peroxide at the surface of a 33-microm diameter disk-shaped carbon-fiber electrode modified by an immobilized glucose-oxidase layer. Sub-monolayer coverage of the enzyme at the electrode surface could be detected with micrometer resolution. The SECM was also employed as a surface modification tool to produce microscopic regions of enzyme activity by using a variety of methods. One method is a gold-masking process in which microscopic gold patterns act as mask for producing patterns of chemical modification. The gold masks allow operation in both a positive or negative process for patterning enzyme activity. A second method uses the direct mode of the SECM to produce covalently attached amine groups on the carbon surface. The amine groups are anchors for attachment of glucose oxidase by use of a biotin/avidin process. The effect of non-uniform enzyme activity was investigated by using the SECM tip to temporarily damage an immobilized enzyme surface. SECM imaging can observe the spatial extent and time-course of the enzyme recovery process.     

Ex Situ Scanning Electrochemical Microscopy (SECM) Investigation of Bismuth‐ and Bismuth/Lead Alloy Film‐Modified Gold Electrodes in Alkaline Medium

Scanning electrochemical microscopy (SECM) in feedback mode was employed to characterise the reactivity and microscopic peculiarities of bismuth and bismuth/lead alloys plated onto gold disk substrates in 0.1 mol L^?1 NaOH solutions. Methyl viologen was used as redox mediator, while a platinum microelectrode was employed as the SECM tip. The metal films were electrodeposited ex situ from NaOH solutions containing either bismuth ions only or both bismuth and lead ions. Approach curves and SECM images indicated that the metal films were conductive and locally reactive with oxygen to provide Bi³⁺ and Pb²⁺ ions. The occurrence of the latter chemical reactions was verified by local anodic stripping voltammetry (ASV) at the substrate solution interface by using a mercury‐coated platinum SECM tip. The latter types of measurements allowed also verifying that lead was not uniformly distributed onto the bismuth film electrode substrate. These findings were confirmed by scanning electron microscopy images. The surface heterogeneity produced during the metal deposition process, however, did not affect the analytical performance of the bismuth coated gold electrode in anodic stripping voltammetry for the determination of lead in alkaline media, even in aerated aqueous solutions. Under the latter conditions, stripping peak currents proportional to lead concentration with a satisfactory reproducibility (within 5 % RSD) were obtained.     

Electrochemical properties of interface formed by interlaced layers of DNA- and lysozyme-coated single-walled carbon nanotubes

Multifunctional coatings were produced by the layer by layer assembly of single-walled carbon nanotubes (SWNT) dispersed in DNA and lysozyme (LSZ) on an insulating glass substrate. The electrochemical properties of these mechanically robust biocoatings were characterized for the first time using scanning electrochemical microscopy (SECM) and impedance spectroscopy (IS). SECM surface analysis demonstrated an increase in tip current with a corresponding increase in the number of oppositely polarized interlaced layers, indicating that subsequent layers were not electrically insulated from each other and a direct correlation exists between SECM feedback response and the number of layers. The rate of charge transport was also dependent on the chemical composition/polarity of the outermost surface layer. Coatings terminating in SWNT-DNA resulted in more positive feedback than those terminating in SWNT-LSZ. IS analysis demonstrated that the SWNT-DNA had a low charge transfer resistance in comparison with SWNT-LSZ, which is consistent with the results obtained by SECM. These results enable enhanced fundamental understanding and prediction of the electrical properties of SWNT-biopolymer layers with controlled interlaced polarities and orientation. Furthermore, these finding highlight the potential for SWNT-biopolymers in electronic and sensing applications.     

A LabVIEW-based virtual instrument for simulation and analysis of SECM approach curves

We have developed a LabVIEW virtual instrument (PAC_Fit.vi) for efficient simulation and analysis of probe approach curve data from a scanning electrochemical microscope (SECM). The virtual instrument (VI) is available for free download and can be used to determine absolute probe height above a substrate, measure rate constants for irreversible electron transfer at a substrate, and perform simulations of SECM approach curves. We anticipate the VI will be of use for educational purposes as well, perhaps as a classroom tool for introducing the principles of SECM. We have applied the VI to an analysis of the dynamic nature of an aluminum alloy (AA2024-T3) substrate immersed in acid solution in which the activity of the substrate increases over time due to dissolution of the passive oxide layer. The value of k _apparent is observed to increase by a factor of 40 over an immersion time of approximately 1 h.     

Microstructuring of solid-supported lipid layers using SAM pattern generation by scanning electrochemical microscopy and the chemical lens

To prepare patterns of adsorption sites for alkanethiols with high lateral resolution, we used the scanning electrochemical microscopy (SECM) to etch masks into uniform layers of nickel coated on gold surfaces. The patterning of the nickel mask was accomplished in aqueous solutions by electrogenerating nitric acid out of nitrite at an ultramicroelectrode. Due to the sluggish kinetics of nickel etching in acidic media, the pattern generated by a 10-microm tip was about 50-microm wide, depending on the duration of the etching. As an alternative, applying the principle of the chemical lens by adding potassium hydroxide as a scavenger, the size of the adsorption sites had been reduced to 4 microm, independent of the duration of etching. In a follow-up step, monolayers of 11-mercaptoundecanoic acid were formed on the exposed gold areas of the surface by self-assembly. Fluorescent liposomes containing tetramethylrhodamine-labeled phospholipids were used to create solid-supported lipid layers (SSLLs). These fluorescent liposomes showed a selective binding affinity to the self-assembled monolayers (SAMs) modified areas, but not to the nickel surface. The patterns generated were imaged by the SECM itself, as well as by optical and fluorescence microscopy.     

Measurement of apparent diffusion coefficients within ultrathin nafion Langmuir-Schaefer films: comparison of a novel scanning electrochemical microscopy approach with cyclic voltammetry

The use of scanning electrochemical microscopy (SECM) to evaluate the apparent diffusion coefficient, Dapp, of redox-active species in ultrathin Nafion films is described. In this technique, an ultramicroelectrode (UME) tip, positioned close to a film on a macroscopic electrode, is used to oxidize (or reduce) a species in bulk solution, causing the tip-generated oxidant (reductant) to diffuse to the film/solution interface. The oxidation (reduction) of film-confined species regenerates the reductant (oxidant) in solution, leading to feedback to the UME. A numerical model is developed that allows Dapp to be determined. For these studies, ultrathin films of Nafion were prepared using the Langmuir-Schaefer (LS) technique and loaded with an electroactive species, either the ferrocene derivative ferrocenyltrimethylammonium cation, FA+, or tris(2,2'-bipyridyl)ruthenium(II), Ru(bpy)32+. The morphology and the thickness of the Nafion LS films (1.5 +/- 0.2 nm per layer deposited) were evaluated using atomic force microscopy (AFM). For comparison with the SECM measurements, cyclic voltammetry (CV) was employed to evaluate the concentration of electroactive species within the Nafion LS films and to determine Dapp. The latter was found to be essentially invariant with film thickness, but the value for Ru(bpy)32+ was 1 order of magnitude larger than for FA+. CV and SECM measurements yield different values of Dapp, and the underlying reasons are discussed. In general, the Dapp values for these films are considerably smaller than for recast Nafion films, which can be attributed to the compactness of Nafion LS films. Nonetheless, the ultrathin nature of the films leads to fast response times, and we thus expect that these modified electrodes could find applications in sensing, electroanalysis, and electrocatalysis.     

Development of Solid Contact Micropipette Zn-Ion Selective Electrode for Corrosion Studies

Micron-size ion selective micropipettes can be used in scanning electrochemical microscopy (SECM). They can provide excellent spatial resolution. Unfortunately the resistance of these small sensors is high. Their application needs special shielding and slow scanning rates. Usually their lifetime hardly exceeds a few days.

Zinc layer or dispersed zinc particles containing films are often used for providing cathodic protection against corrosion in case of metal surfaces. Therefore, in corrosion studies, measurements of local zinc ion concentration can give important information about the nature of the process. For corrosion studies we needed SECM measuring tips for imaging concentration profiles of Zn²⁺ions involved in surface processes. Based on our earlier experience, solid contact micropipettes for selective measurements of Zn²⁺ion concentration were prepared with a tip size of a few micrometers. The properties of the micropipettes were investigated. They were also used in SECM imaging. In this paper, details of Zn²⁺ion selective microelectrode preparation are described. Data about their properties, lifetime, resistance, and ion activity response are shown. Preliminary findings in SECM imaging of zinc ion concentration profiles are shown. The improvement of the scanning rate achieved by lowering tip resistance is a main advantage in potentiometric SECM.     

Tip current/positioning close-loop mode of scanning electrochemical microscopy for electrochemical micromachining

Scanning electrochemical microscopy (SECM) has been approved as a prospective electrochemical micromachining (ECMM) technique soon after its birth. However, it still remains challenge for SECM to fabricate arbitrary three-dimensional (3D) microstructures because of the limitation of positioning system. To solve this problem, we proposed a tip current signal/positioning close-loop mode in which the tip current signal is fed back to the positioning system in order to program the motion trial of SECM tip. Both the triedge-cone and sinusoidal microstructures were obtained by the close-loop positioning mode. The static-state etching process was demonstrated not to be disturbed by the slow motion rate of SECM tip. The unique positioning mode would be significant for both ECMM and electrochemical imaging.     

On the diffusion of ferrocenemethanol in room-temperature ionic liquids: an electrochemical study

The electrochemical behaviour of ferrocenemethanol (FcMeOH) has been studied in a range of room-temperature ionic liquids (RTILs) using cyclic voltammetry, chronoamperomery and scanning electrochemical microscopy (SECM). The diffusion coefficient of FcMeOH, measured using chronoamperometry, decreased with increasing RTIL viscosity. Analysis of the mass transport properties of the RTILs revealed that the Stokes-Einstein equation did not apply to our data. The "correlation length" was estimated from diffusion coefficient data and corresponded well to the average size of holes (voids) in the liquid, suggesting that a model in which the diffusing species jumps between holes in the liquid is appropriate in these liquids. Cyclic voltammetry at ultramicroelectrodes demonstrated that the ability to record steady-state voltammograms during ferrocenemethanol oxidation depended on the voltammetric scan rate, the electrode dimensions and the RTIL viscosity. Similarly, the ability to record steady-state SECM feedback approach curves depended on the RTIL viscosity, the SECM tip radius and the tip approach speed. Using 1.3 μm Pt SECM tips, steady-state SECM feedback approach curves were obtained in RTILs, provided that the tip approach speed was low enough to maintain steady-state diffusion at the SECM tip. In the case where tip-induced convection contributed significantly to the SECM tip current, this effect could be accounted for theoretically using mass transport equations that include diffusive and convective terms. Finally, the rate of heterogeneous electron transfer across the electrode/RTIL interface during ferrocenemethanol oxidation was estimated using SECM, and k(0) was at least 0.1 cm s(-1) in one of the least viscous RTILs studied.     

Scanning electrochemical microscope observation of defects in a hexadecanethiol monolayer on gold with shear force-based tip-substrate positioning

Scanning electrochemical microscopy (SECM) was used for imaging of n-hexadecanethiol-modified Au surfaces. In these studies, small defects were observed in the monolayer when a submicrometer electrode was used as an SECM tip, although a cyclic voltammogram of a Au disk electrode showed that the surface of the Au was completely covered with n-hexadecanethiol. The dependence of the SECM images on the potential of the Au electrode was also examined. A comparison of the current at the Au electrode and the tip current in the SECM images showed that direct electron transfer through the monolayer was dominant, rather than electron transfer at the defects. The size of the defects was estimated from the tip current to be 1-100 nm, under the assumption that the defects were small compared to the SECM probe.     

Scanning Electrochemical Microscopy for Electrochemical Detection of Single‐base Mismatches by Tagging Ferrocenecarboxylic Acid as a Redox Probe to DNA

Scanning electrochemical microscopy (SECM) was employed for sensitive detection of single base mismatches (SBMs) in a sandwiched dsDNA. Ferrocenecarboxylic acid (Fc), covalently conjugated to the dsDNA, was oxidized to Fc⁺ via the DNA‐mediated charge transfer from the underlying gold substrate, and reduced back to Fc by SECM tip generated ferrocyanide. The electrocatalytic oxidation of SECM tip‐generated ferrocyanide was sensitive to presence, as well as the type of SBMs. Apparent standard rate constants (k⁰_app) values for different SBMs, both near the electrode surface and far from it, were evaluated by SECM. The method can detect SBMs independent of their position in dsDNA.     

Optimized preparation and scanning electrochemical microscopy analysis in feedback mode of glucose oxidase layers grafted onto conducting carbon surfaces

An optimized immobilization procedure based on the electroreduction of aryldiazonium salt followed by covalent attachment of a cross-linked hydrogel was used to graft glucose oxidase on a carbon surface. Scanning electrochemical microscopy (SECM) and cyclic voltammetry were used to follow the construction steps of the modified electrode. By adjusting the compactness of the layer through the electrografting reaction, the penetration of the mediator through the layer can be controlled to allow the monitoring of the enzymatic activity by both cyclic voltammetry and SECM in feedback mode. The enzymatic activity of the film is finally characterized by SECM.