Enhanced electrochemical properties of polyethylene oxide-based composite solid polymer electrolytes with porous inorganic–organic hybrid polyphosphazene nanotubes as fillers

Solid composite polymer electrolytes consisting of polyethylene oxide (PEO), LiClO₄, and porous inorganic–organic hybrid poly (cyclotriphosphazene-co-4, 4′-sulfonyldiphenol) (PZS) nanotubes were prepared using the solvent casting method. Differential scanning calorimetry and scanning electron microscopy were used to determine the characteristics of the composite polymer electrolytes. The ionic conductivity, lithium ion transference number, and electrochemical stability window can be enhanced after the addition of PZS nanotubes. The electrochemical impedance showed that the conductivity was improved significantly. Maximum ionic conductivity values of 1.5 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.8 × 10⁻⁴ S cm⁻¹ at 80 °C were obtained with 10 wt.% content of PZS nanotubes, and the lithium ion transference number was 0.35. The good electrochemical properties of the solid-state composite polymer electrolytes suggested that the porous inorganic–organic hybrid polyphosphazene nanotubes had a promising use as fillers in SPEs and the PEO₁₀–LiClO₄–PZS nanotube solid composite polymer electrolyte might be used as a candidate material for lithium polymer batteries.     

PVDF-HFP composite polymer electrolyte with excellent electrochemical properties for Li-ion batteries

Poly (vinylidene fluoride-co-hexafluoropropylene)-based composite polymer electrolyte (CPE) was prepared by phase inversion technique. In this work, we first applied a novel surface-modified sub-micro-sized alumina, PC-401, as ceramic filler. Various electrochemical methods were applied to investigate the electrochemical properties of the polymer electrolytes. We found that the CPE with 10 wt.% PC-401 has excellent electrochemical properties, including the ionic conductivity as high as 0.89 mS cm⁻¹ and the Li-ion transference number of 0.46. Polymer Li-ion batteries using LiFePO₄ as cathode active material exhibited excellent cycling and high-temperature performances. PC-401 shows a promising applicability in the preparation of polymer electrolyte with high electrochemical properties.     

Synthesis and characterization of structure optimized film doped with Rhodamine 6G

Amplified spontaneous emission (ASE) property of a red dye rhodamine 6 g (R6G) doped into a highly ordered mesoporous SBA-15 film and a planar waveguide poly (4-vinylphenol) (P4VP) film were studied and compared. Regular morphology and mesoporous structure have been evidenced from the photographs, TEM and Nitrogen adsorption–desorption characterizations. A narrower, higher peak was observed in emission spectra from the meso-structured SBA-15 film doping with R6G (R6G/SBA-15) compared with the photoluminescence (PL) spectrum that of R6G in C₂H₅OH (R6G/C₂H₅OH) solution, was abruptly narrowed down to a line-width of about 9.8 nm when pumping at an energy of 0.12 mJ pulse⁻¹, which indicates a favorable ASE property in R6G/SBA-15 film. Comparing the P4VP film spin-coating with R6G (R6G/P4VP), the R6G/SBA-15 film exhibited a much narrower and stronger emission spectrum when it is pumped by the 355 nm pulsed source at the same pumping energy, which means that the meso-structure of the SBA-15 film can optimize ASE property of the material. The threshold was easily obtained by R6G/SBA-15 film at 0.02 mJ pulse⁻¹, and it was lower than that of R6G/P4VP film. The optimized ASE property owes much to the effects of the better spatial confinement of the molecules in the ordered mesoporous structure of SBA-15 film.     

Effect of nanoscale CeO<Subscript>2</Subscript> on PVDF-HFP-based nanocomposite porous polymer electrolytes for Li-ion batteries

New poly (vinylidenefluoride-co-hexafluoro propylene) (PVDF-HFP)/CeO₂-based microcomposite porous polymer membranes (MCPPM) and nanocomposite porous polymer membranes (NCPPM) were prepared by phase inversion technique using N-methyl 2-pyrrolidone (NMP) as a solvent and deionized water as a nonsolvent. Phase inversion occurred on the MCPPM/NCPPM when it is treated by deionized water (nonsolvent). Microcomposite porous polymer electrolytes (MCPPE) and nanocomposite porous polymer electrolytes (NCPPE) were obtained from their composite porous polymer membranes when immersed in 1.0 M LiClO₄ in a mixture of ethylene carbonate/dimethyl carbonate (EC/DMC) (v/v = 1:1) electrolyte solution. The structure and porous morphology of both composite porous polymer membranes was examined by scanning electron microscope (SEM) analysis. Thermal behavior of both MCPPM/NCPPM was investigated from DSC analysis. Optimized filler (8 wt% CeO₂) added to the NCPPM increases the porosity (72%) than MCPPM (59%). The results showed that the NCPPE has high electrolyte solution uptake (150%) and maximum ionic conductivity value of 2.47 × 10⁻³ S cm⁻¹ at room temperature. The NCPPE (8 wt% CeO₂) between the lithium metal electrodes were found to have low interfacial resistance (760 Ω cm²) and wide electrochemical stability up to 4.7 V (vs Li/Li⁺) investigated by impedance spectra and linear sweep voltammetry (LSV), respectively. A prototype battery, which consists of NCPPE between the graphite anode and LiCoO₂ cathode, proves good cycling performance at a discharge rate of C/2 for Li-ion polymer batteries.     

Organo-modified mesoporous silica for sorption of carbon dioxide

Abstract  

Organo-modified mesoporous silica SBA-15 has been studied for sorption of carbon dioxide (CO₂). The SBA-15 sample was functionalized with a branched chain polymer, polyethylenimine (PEI), of different molecular weights (1,300 and 2,000 g mol⁻¹). Surface modification was carried out by impregnation of silica by PEI or by grafting with (3-chloropropyl)triethoxysilane, followed by substitution of chlorine atoms by PEI ligands. The prepared modified mesoporous materials were characterized by nitrogen adsorption/desorption at 77 K, high-resolution transmission electron microscopy, small-angle X-ray scattering, and thermal methods. Sorption of CO₂ was studied by gravimetric method at 303 K. The total amount of sorbed CO₂ varied between 0.19–0.67 mmol/g for respective samples. Regeneration of the materials after adsorption was achieved by thermal treatment at 343 K.     

Improved properties of polymer electrolyte by ionic liquid PP1.3TFSI for secondary lithium ion battery

A new kind of polymer electrolyte is prepared from N-methyl-N-propylpiperidinium bis (trifluoromethanesulfonyl) imide (PP1.3TFSI), polyethylene oxide (PEO), and lithium bis (trifluoromethanesulfonyl) imide (LiTFSI). IR and X-ray diffraction results demonstrate that the addition of ionic liquid decreases the crystallization of PEO. Thermal and electrochemical properties have been tested for the solid polymer electrolytes, the addition of the room temperature molten salt PP1.3TFSI to the conventional P(EO)₂₀LiTFSI polymer electrolyte leads to the improvement of the thermal stability and the ionic conductivity (x = 1.27, 2.06 × 10⁻⁴ S cm⁻¹ at room temperature), and the reasonable lithium transference number is also obtained. The Li/LiFePO₄ cell using this polymer electrolyte shows promising reversible capacity, 120 mAh g⁻¹ at room temperature and 164 mAh g⁻¹ at 55 °C.     

Synthesis and characterization of core–shell F-doped LiFePO<Subscript>4</Subscript>/C composite for lithium-ion batteries

Core–shell LiFePO₄/C composite was synthesized via a sol–gel method and doped by fluorine to improve its electrochemical performance. Structural characterization shows that F⁻ ions were successfully introduced into the LiFePO₄ matrix. Transmission electron microscopy verifies that F-doped LiFePO₄/C composite was composed of nanosized particles with a ~3 nm thick carbon shell coating on the surface. As a cathode material for lithium-ion batteries, the F-doped LiFePO₄/C nanocomposite delivers a discharge capacity of 162 mAh/g at 0.1 C rate. Moreover, the material also shows good high-rate capability, with discharge capacities reaching 113 and 78 mAh/g at 10 and 40 C current rates, respectively. When cycled at 20 C, the cell retains 86% of its initial discharge capacity after 400 cycles, demonstrating excellent high-rate cycling performance.     

EC modified PEO/PVDF-LLZO composite electrolytes for solid state lithium metal batteries

The polymer-ceramic composite electrolytes have great application potential for next-generation solid state lithium batteries, as they have the merits to eliminate the problem of liquid organic electrolytes and enhancing chemical/electrochemical stability. However, polymer-ceramic composite electrolytes show poor ionic conductivity, which greatly hinders their practical applications. In this work, the addition of plasticizer ethylene carbonate (EC) into polymer-ceramic composite electrolyte for lithium batteries effectively promotes the ionic conductivity. A high ionic conductivity can be attained by adding 40 wt% EC to the polyethylene oxide (PEO)/polyvinylidene fluoride (PVDF)-Li₇La₃Zr₂O₁₂ (LLZO) based polymer-ceramic composite electrolytes, which is 2.64 × 10⁻⁴ S cm⁻¹ (tested at room temperature). Furthermore, the cell assembled with lithium metal anode, this composite electrolyte, and LiFePO₄ cathode can work more than 80 cycles at room temperature (tested at 0.2 C). The battery delivers a high reversible specific capacity after 89 cycles, which is 119 mAh g⁻¹.     

Characterization and properties of ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes

Gel polymer electrolytes containing 1-ethyl-3-methylimidazolium-bis (trifluoromethyl-sulfnyl)imide (EMITFSI) ionic liquid were prepared for lithium ion batteries by solution casting method. Thermal and electrochemical properties have been determined for the gel polymer electrolytes. Proper addition of EMITFSI to the P(VdF-HFP)-LiTFSI polymer electrolyte improves the ionic conductivity and electrochemical window to 2.11 × 10⁻³ S cm⁻¹ (30 °C) and 4.6 V. In combination of the prepared ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes, Li₄Ti₅O₁₂ anode exhibited two extra voltage plateaus around 1.1 V and 2.3 V except the typical voltage plateau around 1.6 V by possible side reaction between ionic liquid and polymer. LiFePO₄ cathode exhibited high capacity above 140 mA h g⁻¹ and retention of 93.1% due to the suppressed polarization effect caused by enhanced ion transport properties. The high temperature of 80 °C didn't have significant impact on the cycling performance.     

Laser Raman and conductivity studies of plasticized polymer electrolyte P(ECH-EO):propylenecarbonate:<Emphasis Type="Italic">γ</Emphasis>-butyrolactone:LiClO<Subscript>4</Subscript>

The plasticized polymer electrolytes composed of poly(epichlorohydrin-ethyleneoxide) (P(ECH-EO)) as host polymer, lithium perchlorate (LiClO₄) as salt, γ-butyrolactone (γ-BL), and propylene carbonate (PC) as plasticizer have been prepared by simple solution casting technique. The effect of mixture of plasticizers γ-BL and PC on conductivity of the polymer electrolyte P(ECH-EO):LiClO₄ has been studied. The band at 457 cm⁻¹ in the Raman spectra of plasticized polymer electrolyte is attributed to both the ring twisting mode of PC and the perchlorate ν ₂(ClO₄⁻) bending. The maximum conductivity value is observed to be 4.5 × 10⁻⁴ S cm⁻¹ at 303 K for 60P(ECH-EO):15PC:10γ-BL:15LiClO₄ electrolyte system. In the present investigation, an attempt has been made to correlate the Raman and conductivity data.     

Polyethylene-supported poly(acrylonitrile-co-methyl methacrylate)/nano-Al2O3 microporous composite polymer electrolyte for lithium ion battery

Nano-Al₂O₃ was doped in poly(acrylonitrile-co-methyl methacrylate) (P(AN-co-MMA)), and polyethylene(PE)-supported P(AN-co-MMA)/nano-Al₂O₃ microporous composite polymer electrolyte (MCPE) was prepared. The performances of the prepared MCPE for lithium ion battery use, including ionic conductivity, electrochemical stability, interfacial compatibility, and cyclic stability, were studied by scanning electron spectroscopy, linear sweep voltammetry, and electrochemical impedance spectroscopy. It is found that the nano-Al₂O₃ significantly affects the MCPE performances. Compared to the MCPE without any nano-Al₂O₃, the MCPE with 10 wt.% nano-Al₂O₃ reaches its best performances. Its ionic conductivity is improved from 2.0 × 10⁻³ to 3.2 × 10⁻³ S cm⁻¹, its decomposition potential is enhanced from 5.5 to 5.7 V (vs Li/Li⁺), and its interfacial resistance on lithium is reduced from 520 to 160 Ω cm². Thus, the battery performance is improved.     

PEO-LITFSI-SiO2-SN System Promotes the Application of Polymer Electrolytes in All-Solid-State Lithium-ion Batteries

All-solid-state polymer lithium-ion batteries are ideal choice for the next generation of rechargeable lithium-ion batteries due to their high energy, safety and flexibility. Among all polymer electrolytes, PEO-based polymer electrolytes have attracted extensive attention because they can dissolve various lithium salts. However, the ionic conductivity of pure PEO-based polymer electrolytes is limited due to high crystallinity and poor segment motion. An inorganic filler SiO₂ nanospheres and a plasticizer Succinonitrile (SN) are introduced into the PEO matrix to improve the crystallization of PEO, promote the formation of amorphous region, and thus improve the movement of PEO chain segment. Herein, a PEO₁₈−LiTFSI−5 %SiO₂−5 %SN composite solid polymer electrolyte (CSPE) was prepared by solution-casting. The high ionic conductivity of the electrolyte was demonstrated at 60 °C up to 3.3×10⁻⁴ S cm⁻¹. Meanwhile, the electrochemical performance of LiFePO₄/CSPE/Li all-solid-state battery was tested, with discharge capacity of 157.5 mAh g⁻¹ at 0.5 C, and capacity retention rate of 99 % after 100 cycles at 60 °C. This system provides a feasible strategy for the development of efficient all-solid-state lithium-ion batteries.     

The network gel polymer electrolyte based on poly(acrylate-co-imide) and its transport properties in lithium ion batteries

Poly (acrylate-co-imide)-based gel polymer electrolytes are synthesized by in situ free radical polymerization. Infrared spectroscopy confirms the complete polymerization of gel polymer electrolytes. The ionic conductivity of gel polymer electrolytes are measured as a function of different repeating EO units of polyacrylates. An optimal ionic conductivity of the poly (PEGMEMA₁₁₀₀-BMI) gel polymer electrolyte is determined to be 4.8 × 10^–3 S/cm at 25 °C. The lithium transference number is found to be 0.29. The cyclic voltammogram shows that the wide electrochemical stability window of the gel polymer electrolyte varies from −0.5 to 4.20 V (vs. Li/Li⁺). Furthermore, we found the transport properties of novel gel polymer electrolytes are dependent on the EO design and are also related to the rate capability and the cycling ability of lithium polymer batteries. The relationship between polymer electrolyte design, lithium transport properties and battery performance are investigated in this research.     

Development of nonflammable lithium ion battery using a new all-solid polymer electrolyte

For solving the safety issue of lithium ion batteries, the choice of all-solid polymer electrolyte is one of the possible solutions. However, usual polyethylene oxide including lithium supporting agent has not enough lithium ion conductivity as electrolyte for practical use. Some of our research group (M. W. and H. M.) have tried the addition of plasticizer such as borate ester or aluminate ester (Al-PEG) into monomer mixture containing lithium salt for increasing the ionic conductivity resulting in polymer electrolyte after polymerization. For such all-solid polymer electrolyte (SPE), the ionic conductivity, a value of 10⁻³ S/cm has been attained at 60 °C and the value will be acceptable for practical use. Since the SPE also has nonflammable property, the combination of the SPE with suitable cathode and anode may produce a new all-solid polymer battery with safety. In the present study, the SPE containing Al-PEG and dimethoxy ethylene glycol mixture as the plasticizer was newly combined with spinel Li₄Ti₅O₁₂ anode and olivine LiFePO₄ cathode objecting for developing stationary battery. The cell performance of the new combination will be reported at 30 °C and 50 °C.     

Synthesis and electrochemical characterization of LiFePO<Subscript>4</Subscript>/C-polypyrrole composite prepared by a simple chemical vapor deposition method

A LiFePO₄/C-polypyrrole (LiFePO₄/C-PPy) composite as a high-performance cathode material is successfully prepared through a simple chemical vapor deposition (CVD) method. According to the transmission electron microscope (TEM) analysis, the surface of the LiFePO₄/C is surrounded with PPy in the LiFePO₄/C-PPy composite. The as-prepared LiFePO₄/C-PPy material shows outstanding rate capability at 20°C and good cycle performance at 55°C in comparison with those of the bare LiFePO₄/C material against Li anode. After 700 cycles, the discharge capacity of LiFePO₄/C-PPy could still remain 110 mA h g⁻¹ with the retention of 82% at 5 C rate at 55°C. This could be ascribed to the fact that PPy coating on LiFePO₄/C could significantly improve the ionic conductivity of the LiFePO₄/C-PPy composite and could greatly reduce the electrode resistance. Furthermore, the PPy coating on LiFePO₄/C could effectively decrease the dissolution of Fe in the LiPF₆ electrolyte and subsequently suppress the reduction of Fe ions on anode.     

Effect of different carbon conductive additives on electrochemical properties of LiFePO4-C/Li batteries

LiFePO₄-C nanoparticles were synthesized by a hydrothermal method and subsequent high-energy ball-milling. Different carbon conductive additives including nanosized acetylene black (AB) and multi-walled carbon nanotube (MWCNT) were used to enhance the electronic conductivity of LiFePO₄. The structural and morphological performance of LiFePO₄-C nanoparticles was investigated by X-ray diffraction (XRD) and scanning electron microscopy. The electrochemical properties of LiFePO₄-C/Li batteries were analyzed by cyclic voltammetry and charge/discharge tests. XRD results demonstrate that LiFePO₄-C nanoparticles have an orthorhombic olivine-type structure with a space group of Pnma. LiFePO₄-C/Li battery with 5 wt% MWCNT displays the best electrochemical properties with a discharge capacity of 142 mAh g⁻¹ at 0.25 C at room temperature.     

Novel composite polymer electrolytes based on poly(ether-urethane) network polymer and fumed silicas

Novel composite solid polymer electrolytes (CSPEs) and composite gel polymer electrolytes (CGPEs) have been prepared. CSPE consists of poly(ether-urethane) network polymer (PUN), fumed silicas and LiClO₄. The ionic conductivity of CSPEs can be enhanced nearly 20 times in comparison with the plain system without the addition of fumed silicas and can be above 1×10⁻⁵ S/cm at room temperature. The effects of both kinds of fumed silicas, viz. uSiO₂ with hydrophilic groups at the surface and mSiO₂ with hydrophobic groups at the surface on ionic conductivity were investigated. CGPE comprising of the CSPE and LiClO₄–PC solution with good mechanical strength exhibits ionic conductivity in the order of 10⁻³ S/cm at room temperature and above 3×10⁻⁴ S/cm at low temperature −40 °C.     

Immobilization of hemoglobin on SBA-15 applied to the electrocatalytic reduction of H<Subscript>2</Subscript>O<Subscript>2</Subscript>

The direct electron transfer between hemoglobin (Hb) and an electrode was realized by first immobilizing the protein onto SBA-15.The results of the immobilization showed that the adsorption was pH-dependent with a maximum adsorption near the isoelectric point of the protein, and SBA-15 with a larger pore diameter showed greater adsorption capacity for Hb. UV–vis spectroscopy and nitrogen adsorption analysis indicated that Hb was adsorbed within the channel of SBA-15 and no significant denaturation occurred to the protein. The Hb/SBA-15 composite obtained was used for the fabrication of a Hb biosensor to detect hydrogen peroxide. A pair of well-defined redox peaks at −0.337 and −0.370 V on the Hb/SBA-15 composite modified glassy carbon electrode was observed, and the electrode reactions showed a surface-controlled process with a single proton transfer at a scan rate range from 20 to 1,000 mV/s. The sensor showed a fast amperometric response, a low detection limit (2.3 × 10⁻⁹ M) and good stability for the detection of H₂O₂. The electrochemical results indicated that the immobilized Hb still retained its biological activity.     

Paper like free-standing hybrid single-walled carbon nanotubes air electrodes for zinc–air batteries

Flexible electrode architectures based on non-functionalized (P2) and functionalized (P3) single-walled carbon nanotubes (SWNTs) were fabricated via a simple vacuum filtration process. A hybrid layer of various compositions of P2- and P3-SWNTs forms free-standing membranes (~80 μm in thickness), and their electrochemical performance was evaluated as an air electrode AEP_2/P3 in zinc–air batteries. Such bifunctionalized air electrodes showed uniform surface morphology with interconnected micron-sized porous structure with high porosity (~70%). The N₂ adsorption isotherms at 77 K are of type IV with BET-specific surface areas of AE_(60/40) and AE_(80/20) to be 130.54 and 158.76 m² g⁻¹, respectively, thus facilitates high active surface area for active oxygen reduction/evolution reactions. BJH pore size distribution of AE_(60/40) and AE_(80/20) shows maximum pores with diameter <15 nm. The zigzag interlaying of the SWNTs imparts mechanical stability and flexibility in zinc–air batteries. Zinc–air batteries with optimized compositions of P2- and P3-SWNTs in air electrode AE_(60/40) had ionic conductivity ~1 × 10⁻² S cm⁻¹ and delivered higher discharge capacity ~300 mAh g⁻¹ as compared to AE_(80/20) composition. The unique properties of AE_(P2/P3) studied in this work would enable flexible air electrode architectures in future metal–air batteries.     

Effects of molecular weight,heating rate,synthetic temperature and sintering duration on electrochemical properties of a LiFePO<Subscript>4</Subscript>/C cathode material pyrolyzed from lithium polyacrylate

A LiFePO₄/C composite was obtained by a polymer pyrolysis reduction method, using lithium polyacrylate (LiPAA) as carbon source and fractional lithium source, and FePO₄·2H₂O as iron and phosphorus source. The structure of the LiFePO₄/C composites was investigated by X-ray diffraction (XRD). The micromorphology of the precursors and LiFePO₄/C powders was observed using scanning electron microscopy (SEM). Laser particle analyzer and BET were also used to characterize the materials. It was found that the micromorphology, particle size distribution and specific surface area of LiFePO₄/C composites were greatly influenced by the molecular weight of LiPAA. The electrochemical properties of the LiFePO₄/C composites were evaluated by cyclic voltammograms (CVs), electrochemical impedance spectra (EIS) and constant current charge/discharge cycling tests. The results showed that the molecular weight of LiPAA, heating rate, synthetic temperature and sintering duration directly affected the electrochemical properties of LiFePO₄/C composites. The sample with the optimized electrochemical properties were obtained in the following conditions, i.e., LiPAA with the molecular weight of 20,000, heating rate of 10 °C min⁻¹, synthetic temperature of 700 °C and sintering duration of 15 h.