利用倾斜光纤光栅的可开关双波长光纤激光器

报导了一种在四波混频作用下利用倾斜光纤布拉格光栅进行波长选择的可开关双波长掺铒光纤激光器。通过将倾斜光纤光栅与单模光纤进行横向错位焊接,使光栅的反向LP01和LP11两个模式具有相近的有效反射率,从而可以用来进行激光器的双波长选择。接入腔内的一段高非线性光子晶体光纤引入的四波混频效应克服了模式竞争,使得双波长激光在室温下稳定振荡。腔内起偏器和偏振控制器的联合作用可产生依赖于波长的损耗,以补偿光纤光栅两反射峰峰值的大小差异。基于以上原理,通过调节腔内的偏振态,该激光器实现了室温下稳定的双波长输出,也实现了在两波长之间的转换。两波长激光均有超过45 dB的信噪比,最大的功率波动为0.8 dB     

Broadly tunable dual-wavelength erbium-doped ring fiber laser based on a high-birefringence fiber loop mirror

A broadly tunable dual-wavelength erbium-doped ring fiber laser based on a high-birefringence fiber loop mirror (HiBi-FLM) and a polarization controller is demonstrated experimentally. The measured transmission spectrum of HiBi-FLM covers a wide range from 1525 to 1575 nm. The wavelength of proposed laser can be flexibly tunable during this range of ∼50 nm by adjusting the polarization controller. In addition, the spacing of two wavelengths is adjustable by changing the length of HiBi fiber. The dual-wavelength lasers with the HiBi fiber length of 1 and 2 m are experimentally demonstrated and compared. The experimental results show that the proposed laser can stably operate on two wavelengths simultaneously at room temperature, and the output peak power variation is about 0.5 dB during 40 min.     

基于两滤波器级联和饱和吸收体的单纵模双波长光纤激光器

提出和证实了一种光纤环形激光器. 将一个带通滤波器与一个带阻滤波器级联,用一段保偏掺铒光纤作为饱和吸收体,得到了一种单纵模双波长光纤激光器. 结果表明,该激光器波长间隔为0.4 nm,边模抑制比大于49 dB.如果将两个波长进行差拍,该激光器有潜力得到49.85 GHz的微波信号.     

Switchable dual-wavelength erbium-doped fiber-ring laser based on one polarization maintaining fiber Bragg grating in a Sagnac loop interferometer

A switchable erbium-doped fiber-ring laser providing dual-wavelength outputs with orthogonal polarizations when operating at room temperature is proposed. One polarization-maintaining fiber Bragg grating (PMFBG) in a Sagnac loop interferometer is used as the wavelength-selective filter. Due to the enhancement of the polarization hole burning (PHB) by the PMFBG, the laser can be designed to operate in stable dual-wavelength or wavelength-switching modes with a wavelength spacing of 0.336 nm at room temperature by adjusting a polarization controller (PC). The optical signal-to-noise ratio (OSNR) is over 42 dB. The amplitude variation over 90 min is less than 0.6 dB for both wavelengths.     

Switchable dual-wavelength polarization-maintaining erbium-doped fiber laser using an optical circulator as the all-reflecting mirror

A simple and effective switchable dual-wavelength polarization-maintaining erbium-doped fiber laser is proposed and demonstrated. Only using a uniform fiber Bragg grating written directly in a segment of the photosensitive and polarization-maintaining erbium-doped fiber as the wavelength selector and an optical circulator as the all-reflecting mirror, a stable simultaneous dual-wavelength oscillation is achieved with a wavelength spacing of 0.364 nm experimentally by exploiting the polarization hole burning effect at room temperature. The output can be switched between single- and dual-wavelength by adjusting the polarization controller. The 3-dB bandwidth and the side mode suppression ratio of the laser’s outputs are measured to be less than 0.01 nm and more than 50 dB. The power fluctuation and wavelength drift are measured to be less than 0.50 dB and 0.020 nm over an hour.     

Switchable triple-wavelength erbium-doped fiber laser using a single fiber Bragg grating in polarization-maintaining fiber

A stable and narrow wavelength spacing multiwavelength erbium-doped fiber laser is proposed and demonstrated. The laser can produce simultaneous dual- and triple-wavelength lasing oscillations with a narrow wavelength spacing of less than 0.1 nm via using a single fiber Bragg gratings written in polarization-maintaining (PM) fiber. By adjusting polarization controller, the wavelength spacing of dual-wavelength lasing oscillations can be tuned to as small as 0.032 nm. The maximum amplitude variation for every lasing wavelength is less than 0.5 dB. The room-temperature operation principle is based on the polarization hole burning and deeply saturated effect in an ordinary erbium-doped fiber ring laser (EDFRL). The laser has the advantages of simple all-fiber configuration, low cost, high stability and operating at room temperature.     

Microwave generation using an all polarization-maintaining linear cavity dual-wavelength fiber laser with tunable wavelength spacing

A stable dual-wavelength erbium-doped fiber laser with a linear cavity is formed by a polarization-maintaining uniform fiber Bragg grating (PM-FBG) and a polarization-maintaining linearly chirped fiber Bragg grating (PM-LCFBG), both of which were fabricated on a high-birefringence (Hi-Bi) fiber. Experimental results show stable dual-wavelength lasing operation with a wavelength separation of ∼0.22 nm, which can be tuned down to as small as 0.05 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room-temperature. Microwave signal at frequency of 9.41, 18.03 and 27.46 GHz is achieved by heterodyned the output lasing wavelengths on a photodetector.     

Dual-wavelength switchable erbium-doped fiber ring laser based on merged sagnac and intermodal interferences in sagnac loop mirror

A simple but novel concept of switchable dual-wavelength erbium-doped fiber ring laser is proposed and experimentally demonstrated. It is based on a Sagnac loop mirror incorporating a high birefringence few-mode fiber and polarization controller (PC). Since its transmission properties depend on the PC state, the proposed fiber ring laser can operate in the random combination of two wavelengths by adjusting only the PC settings. The potential lasing lines are determined by simultaneous occurrence of the Sagnac and intermodal interferences in the Sagnac loop mirror. All lasing emissions have the optical signal to noise extinction ratio higher than 45 dB and their power fluctuations lower than 0.5 dB.     

Tunable microwave photonic notch filter using a dual-wavelength fiber laser with phase modulation

A novel tunable microwave photonic notch filter using a phase-modulated dual-wavelength fiber laser is presented. A stable dual-wavelength erbium-doped fiber laser with a linear cavity is formed by a polarization-maintaining uniform fiber Bragg grating (PM-FBG) and a polarization maintaining linearly chirped fiber Bragg grating (PM-LCFBG), both of which were fabricated on a high-birefringence (Hi-Bi) fiber. It is found that a stable room-temperature dual-wavelength operation can be achieved due to the presence of two reflection peaks arising from the orthogonal states of polarization (SOP) of the PM-FBG. Experimental results show stable dual-wavelength lasing operation with a wavelength separation of ∼0.36 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. The dual-wavelength fiber laser is combined with a phase modulator and a segment of single-mode fiber (SMF) as a dispersive device to form a tunable microwave photonic notch filter. By stretching the PM-FBG to tune the wavelength separation of the dual-wavelength fiber laser, a tunable microwave photonic notch filter with various free spectral ranges (FSRs) and a rejection ratio greater than 35 dB was developed.     

Dual-Wavelength Erbium-Doped Fibre Ring Laser by Cascading Tunable Bandpass Filter with Bandstop Filter

A novel fibre ring laser is proposed and successfully demonstrated. By cascading a tunable bandpass filter with a bandstop filter to construct the desired narrow dual-transmission-peak spectrum, and employing a segment of unpumped erbium-doped fibre as a saturable absorber, a stable fibre ring laser is achieved at room temperature. The proposed laser can operate in dual-wavelength with the wavelength spacing of 0.48 nm and the extinction ratio more than 50 dB or switch between the two wavelengths by adjusting a polarization controller. The stability is investigated experimentally and explained theoretically.     

Photonic generation of a microwave signal by incorporating a delay interferometer and a saturable absorber

A novel approach to generate microwave signals is presented by employing a dual-wavelength erbium-doped fiber ring laser. By using a delay interferometer as a comb filter cascaded with a tunable bandpass filter and a saturable absorber formed by an unpumped polarization-maintaining erbium-doped fiber, a stable wavelength-tunable dual-wavelength single longitudinal-mode laser is achieved. A microwave signal at 20.07 GHz with a linewidth of <25 kHz is demonstrated by beating the two wavelengths at a photodetector.     

Switchable and tunable dual-wavelength ultrashort pulse generation in a passively mode-locked erbium-doped fiber ring laser

A simple switchable and tunable dual-wavelength passively mode-locked erbium-doped fiber ring laser based on nonlinear polarization rotation (NPR) effect is proposed and experimentally demonstrated. The NPR effect effectively induces wavelength- and intensity-dependent loss to readily implement stable dual-wavelength passively mode-locked operation. The wavelength switching and tuning of the dual-wavelength ultrashort pulse laser are achieved only by appropriately rotating the polarization controllers. The side-mode suppression ratio of the output pulse is larger than 41 dB over a wavelength-tuning range of 43.4 nm. Moreover, triple-wavelength ultrashort pulse can also be observed.     

Wavelength-spacing tunable multiwavelength erbium-doped fiber laser based on four-wave mixing of dispersion-shifted fiber

We experimentally demonstrate a wavelength-spacing tunable multiwavelength erbium-doped fiber laser based on degenerate four-wave mixing in a dispersion-shifted fiber incorporating multiple-fiber Bragg gratings. We have achieved stable operation of the multiwavelength erbium-doped fiber laser, which has 0.8 nm spacing ten-channel lasing wavelengths and a high extinction ratio of more than approximately 45 dB, at room temperature. The output power of the multiwavelength erbium-doped fiber laser is stable, so the peak fluctuation is less than approximately 0.2 dB. By changing the properties such as loss and polarization state of multiple fiber Bragg grating cavities, we can exercise flexible control of the wavelength spacing of the multiwavelength output. We can also obtain switchable multiwavelength lasing operation by elimination of the effects of alternate single-fiber Bragg gratings.     

A novel dual-wavelength fiber Bragg grating and its application in fiber ring laser

A novel method for fabricating dual-wavelength fiber Bragg gratings (FBGs) by using one phase mask is developed. The method is based on a double-exposure technique. Our technique lends itself to writing gratings with controllable reflectivity and separation of two Bragg wavelengths. A grating with two equal transmission peaks of 20.25 dB is obtained by this method and the separation of the two Bragg wavelengths is about 0.8 nm. With the grating, we demonstrate a dual-wavelength erbium-doped fiber ring laser whose interval of the two peaks is 0.8 nm. The laser's peak powers can get 3.1 mW above and have a good stability.     

Switchable single-longitudinal-mode dual-wavelength erbium-doped fiber ring laser based on one polarization-maintaining fiber Bragg grating incorporating saturable absorber and feedback fiber loop

Switchable single-longitudinal-mode (SLM) dual-wavelength erbium-doped fiber ring laser based on one polarization-maintaining fiber Bragg grating (PMFBG) is demonstrated. Due to the enhancement of the polarization hole burning (PHB) by the PMFBG, the laser can be designed to operate in stable dual-wavelength or wavelength-switching modes with a wavelength spacing of 0.336 nm at room temperature by adjusting a polarization controller (PC). The stable SLM operation is guaranteed by a compound-ring cavity and a saturable absorber (SA). The optical signal-to-noise ratio (OSNR) is over 45 dB. The amplitude variation in nearly one and half an hour is less than 0.2 dB.     

A Proposal and Demonstration for Photonic Generation of a Microwave Signal by Incorporating a Microring Resonator

A proposal for photonic generation of a microwave signal is presented by employing a dual wavelength erbiumdoped fibre ring laser. In the laser, a microring resonator is cascaded with a tunable bandpass filter to serve as a dual-wavelength selector, an unpumped polarization maintaining erbium-doped fibre is used as a saturable absorber. By replacing the microring resonator with a delay interferometer to verify the proposal, a wavelengthtunable dual wavelength single longitudinal mode laser is demonstrated, and a microwave signal at 10.01 GHz with a linewidth of less than 25 kHz is obtained by beating the two wavelengths at a photodetector.     

Tunable single- and dual-wavelength erbium-doped fiber laser based on Sagnac filter with a high-birefringence photonic crystal fiber

In this paper, we observed and experimentally investigated a high-performance single- and dual-wavelength erbium-doped fiber ring laser based on a Sagnac filter which contains a section of high-birefringence photonic crystal fiber (HB-PCF) and a polarization controller. Incorporation of the high-birefringence photonic crystal fiber can suppress multimode oscillation, improve power stability and increase the optical signal-to-noise ratio (SNR). Wavelength tunable was achieved by using a polarization controller in the Sagnac filter. Highly stable single-, dual-wavelength oscillations are tunable within a wavelength range from 1550 to 1562 nm and SNR as high as 57 dB with narrow line width about 0.011 nm, is experimentally demonstrated.     

A tunable narrow-line-width multi-wavelength Er-doped fiber laser based on a high birefringence fiber ring mirror and an auto-tracking filter

A novel multi-wavelength erbium-doped fiber laser operating in C-band is proposed and successfully demonstrated. The wavelength interval between the wavelengths is about 0.22 nm. The 3 dB bandwidth of the laser is about 0.012 nm, and the output power reaches 4.8 mW. By using a high birefringence fiber ring mirror (HiBi-FLM) and a tunable FBG, the laser realizes switchable and tunable characteristic. The mode hopping can be effectively prevented. Moreover, this laser can improve wavelength stability significantly by taking advantage of an un-pumped Er³⁺-doped fiber at the standing-wave section. The laser can operate in stable narrow-line-width with single-, dual-wavelength, and unstable triple-wavelength output at room temperature.     

Polarization controlled multiwavelength switchable erbium-doped fiber laser based on high birefringence few-mode fiber loop mirror

A multiwavelength switchable erbium-doped fiber laser with linear cavity is proposed and experimentally demonstrated. It is based on a fiber loop mirror incorporating a piece of high birefringence few-mode fiber and polarization controller. Due to dependence of its reflection properties on the polarization controllers, the fiber laser can operate in the random combination of three wavelengths by only adjusting the polarization controllers in the linear cavity. The wavelengths involved in the switching operation are determined by the merged Sagnac and intermodal interferences elicited in the fiber loop mirror. The optical signal to noise extinction ratio of every oscillation line is higher than 40 dB and power fluctuation less than 0.5 dB.     

Mode-locked fiber laser in the C-band region for dual-wavelength ultrashort pulses emission using a carbon nanotube saturable absorber

A saturable absorber is commonly employed to generate an ultrashort laser with a mode-locking scheme. In an erbium-doped fiber laser system, the laser regimes of either 1530 or 1550 nm wavelength are procured based on the absorption profile of the erbium-doped fiber. The absorption of the erbium-doped fiber is designed to emit at both wavelengths by controlling the net gain of the laser cavity. Subsequently, simultaneous erbium-doped fiber laser emission is attained at 1533.5 and 1555.1 nm with the pulse duration of 910 and 850 fs, respectively.Therefore, this work maximizes the output portfolios of a mode-locking fiber laser for dual-wavelength ultrashort pulses emission.