Analysis of clindamycin by micellar electrokinetic chromatography with a mixed micellar system.

This study details the development and validation of an optimized method with micellar electrokinetic chromatography for the analysis of clindamycin. The method uses a mixed micellar phase containing anionic sodium dodecylsulfate (SDS) and non ionic Brij 35 on an untreated fused-silica capillary. The influences of buffer concentration, pH, SDS, Brij 35 and organic modifier were investigated. Special attention was given to the role of the non ionic Brij 35 in the mixed micellar system. Optimization with a central composite design resulted in optimal separation conditions: background electrolyte containing 25 mM sodium tetraborate pH 7.75, 90 mM SDS, 14 mM Brij 35 and 21% acetonitrile. The applied voltage was 15 kV and the capillary temperature 15 degrees C. The method was robust and gave good linearity and repeatability. The limits of detection and quantitation were 0.05 and 0.15%, respectively, relative to a 2.5 mg/ml clindamycin solution. Two commercial bulk products were analysed with this system.     

On-line concentration by field-enhanced sample injection with reverse migrating micelles in micellar electrokinetic capillary chromatography for the analysis of flavonoids in Epimedium brevicornum Maxim

A simple and sensitive micellar electrokinetic capillary chromatography (MEKC) method was developed for the separation and determination of six flavonoids in Epimedium brevicornum Maxim. Field-enhanced sample injection with reverse migrating micelles (FESI-RMM) was used for on-line concentration of the flavonoids. An electrolyte containing 20 mM H3PO4, 100 mM SDS, 20% acetonitrile and 2% 2-propanol (pH 2.0) was chosen as the electrophoretic buffer. By optimizing the stacking conditions, about 40-360-fold improvement in the detection sensitivity was obtained for the flavonoids.     

Separation of serum bilirubin species by micellar electrokinetic chromatography with direct sample injection.

Four major bilirubin species in serum were separated by micellar electrokinetic chromatography with 25 mM sodium dodecyl sulfate (SDS) and 20 mM sodium tetraborate-boric acid buffer at pH 8.5. Due to the solubilization of the serum proteins by the SDS micelles, serum samples were injected directly into a 50 cm x 75 microns I.D. fused-silica capillary and complete separation of the four bilirubin species was accomplished within ca. 10 min without extensive sample pretreatment. Detection was performed by absorbance at 450 nm and average limit of detection was in the 6.0 microM concentration range. The usefulness of this method was demonstrated for the separation and detection of a number of bilirubin species present in pathological human serum samples.     

Analysis of artichoke (Cynara cardunculus L.) extract by means of micellar electrokinetic capillary chromatography

The main constituents of artichoke extract were separated by micellar electrokinetic chromatography (MEKC), using a buffer consisting of 100 mM sodium dodecyl sulfate (SDS) in 20 mM sodium dihydrogen phosphate, 20 mM disodium tetraborate (pH 8.6) as background electrolyte. Optimum separation voltage of 28 kV (positive polarity) and a capillary temperature of 25 degrees C gave the best analysis. The UV detection was performed at 200 nm. The method was successfully used to analyze plant and drug samples as well as for the study of artichoke antioxidant activity. The quantitative MEKC results were in good agreement to those obtained previously by reversed-phase high-performance liquid chromatography (RP-HPLC).     

Highly efficient separation of isomeric epoxy fatty acids by micellar electrokinetic chromatography

A capillary electrophoresis (CE) method has been developed for simple and direct separation of cis- and trans-12,13-epoxy-9(Z)-octadecenoic acid and 9,10-epoxy-12(Z)-octadecenoic acid isomers. Separation was performed in micellar electrokinetic capillary chromatography (MEKC) using a buffer consisting of 25 mM borate (pH 9.20), 10 mM sodium dodecyl sulfate (SDS) and 10% v/v acetonitrile. The key variables, concentrations of SDS and organic modifier, were optimized by the application of a factorial experimental design. The use of a low micellar concentration, just above critical micelle concentration (CMC), in a background electrolyte containing an organic modifier not only made it possible to dissolve and separate highly hydrophobic fatty acid isomers, but also resulted in improved separation efficiency and selectivity. Separation efficiency up to 4 x 10(5) theoretical plates/m was achieved under an optimized condition. Also investigated were the influence of temperature on separation and the effect of organic modifier concentration on the dynamic exchange of the analytes between micelles and the bulk of the buffer solution. Direct UV was applied for detection of the fatty acids.     

Determination of antitubercular drugs by micellar electrokinetic capillary chromatography (MEKC)

A method for the determination of isoniazid (ISO), pyrazinamide (PYR) and rifampicin (RIF) in pharmaceutical products, by micellar electrokinetic capillary chromatography (MEKC) with ultraviolet detection is described. The influence of pH, concentration of surfactants, buffer and organic solvents, over the separation were studied as experimental variables. The optimal separation was carried out at 30 degrees C and 20 kV, using a 40 mM borate buffer and 100 mM sodium dodecylsulphate (SDS) adjusted to pH 8.5. Under these conditions, the analysis is accomplished in about 8 min. The method was applied to the determination of these compounds in different pharmaceuticals with good results when compared with a reference liquid chromatographic (LC) method.     

Analysis of antiepileptic drugs in human plasma using micellar electrokinetic capillary chromatography.

We describe a method for the simultaneous determination of antiepileptic drugs (ethosuccimide, phenytoin, primidone, phenobarbital, carbamazepine and valproic acid) by micellar electrokinetic capillary chromatography using sodium dodecyl sulphate as the micellar phase. Factors affecting the micellar electrokinetic separation were studied for the quantitative determination of these drugs in human plasma. The confirmation of the peaks and the specificity of the method were investigated by combining multiwavelength detection with micellar electrokinetic capillary chromatography.     

Direct multicomponent analysis of beer samples constituents using micellar electrokinetic capillary chromatography

A capillary electrophoretic method was developed using micellar electrokinetic capillary chromatography (MEKC) with diode-array detection to analyze simultaneously 26 beer constituents in a single procedure, including alcohols, iso-alpha-acids, amino acids, flavonoids, isoflavonoids, a vitamin, purine and pyrimidine bases. After filtration, sample components were separated with an uncoated capillary and a 25 mM sodium borate and 110 mM SDS buffer at pH 10.5. Analyses were run at 14 kV and 8 s of hydrodynamic injection with UV detection at 210 nm and 270 nm. The proposed method was successfully applied to the direct determination of beer constituents without any sample cleanup procedures.     

Characterization of anacardic acids by micellar electrokinetic chromatography and mass spectrometry

A possibility of using capillary electrophoresis for separation of anacardic acids (6-alkylsalicylic acids) has been studied. Conventional micellar electrokinetic chromatography (MEKC) in non-coated fused silica capillaries and reversed-flow micellar electrokinetic chromatography (RF-MEKC) in capillaries coated with polydimethylacrylamide was applied for separation of anacardic acids extracted from cashew nuts. Influence of the composition of background electrolyte on the resolution of anacardic acid isomers was evaluated. Separations were performed using sodium dodecyl sulphate (SDS) micelles and mixed micelles of SDS and polyoxyethylene lauryl ether as a pseudostationary phase. To further improve the separation in RF-MEKC, beta-cyclodextrin and a dual cyclodextrin system of beta-cyclodextrin with heptakis-6-sulphato-beta-cyclodextrin was added to the working electrolyte. Best separation of anacardic acids were achieved in the polydimethylacrylamide-coated capillary using 10 mM phosphate background electrolyte pH 6.5 with addition of 1 M urea, 20% acetonitrile, 10 mM of beta-cyclodextrin and 1 mM of heptakis-6-sulfo-beta-cyclodextrin. Mass spectrometry was used for the identification of anacardic acids in the extract from cashew nuts in single and tandem mode using Q-TOF instrument. Nine anacardic acids were identified in the extract form the cashew nuts.     

Fenofibrate and fenofibric acid analysis by capillary electrophoresis

A capillary electrophoresis method has been developed to measure fenofibrate in capsules based on micellar electrokinetic capillary chromatography with detection at 280 nm using a borate buffer containing sodium dodecyl sulfate (SDS). However, the metabolite of this drug (fenofibric acid) in serum and whole blood was analyzed by capillary zone electrophoresis (CZE) in a borate-carbonate buffer using acetonitrile stacking. The analysis is rapid, < 7 min with no interferences. Incubation of fenofibrate in whole blood caused hydrolysis of the ester bond with the release of fenofibric acid.     

Determination of synthesized alpha-vitamin E by micellar electrokinetic chromatography

We developed a micellar electrokinetic chromatography method (MEKC) for the direct determination of the content of synthesized alpha-vitamin E. It was found that under the optimum separation conditions 7 mM borate + 14 mM phosphate + 15 mM sodium dodecyl sulfate (SDS) + 10 mM sodium cholate (NaCh) + 8% acetonitrile (pH 9.2) with UV detection wavelength at 214 nm, 16 kV constant voltage, and 26 degrees C constant temperature, alpha-vitamin E and its isomers can be baseline separated and alpha-vitamin E was quantitatively analyzed. In addition, the sample recovery, the limit of detection and the repeatability of the method were investigated. The influence of various parameters on the separation such as SDS concentration, NaCh concentration, buffer pH and acetonitrile percentage were also discussed.     

Novel approach to the analysis and use of fullerenes in capillary electrophoresis

The analysis and use of fullerenes in capillary electrophoresis (CE) was investigated. Sodium dodecyl sulfate (SDS) was used to solubilize fullerenes C60, C70, and a mixture of C60 and C70 in water. The behavior of the solutions of the C60- and C70-SDS complexes was examined by CE with on-line UV-Vis diode array detection. This study included the use of a C60-SDS complex as a new method of micellar electrokinetic chromatography (MEKC) for the separation of polycyclic aromatic hydrocarbons (PAHs) using CE with uniwavelength detection. Since SDS micelles act as a pseudostationary phase in which the PAH compounds partition with their hydrophobic interior, the addition of C60 within the micelles enhanced separation of the PAHs. The preliminary results using C60-MEKC with SDS were compared to those obtained with MEKC with SDS. The capillary electrophoretic separations were performed in 10 mM borate-phosphate buffer with 100 mM SDS at pH 9.5.     

Separation of related opiate compounds using capillary electrochromatography

Capillary electrophoretic separations have been investigated for six controlled narcotic analgesic compounds having related structures. Owing to the similar charge-to-mass ratios of these compounds, capillary zone electrophoresis failed to provide a satisfactory separation, whereas a baseline-resolved separation was achieved in 10 min using micellar electrokinetic chromatography. Column efficiencies of 40,000-150,000 plates/m were obtained with a 50 cm long, 50 microm inner diameter (ID) capillary using 50 mM sodium dodecyl sulfate (SDS) in a 50 mM borate solution containing 12% isopropanol. In contrast, separation of this mixture by capillary electrochromatography proved to be significantly superior. The capillary was 15 cm long, with an ID of 75 microm, and was packed with 1.5 microm nonporous octadecyl silica (ODS) particles. The mobile phase consisted of 80% 10 mM tris(hydroxymethyl)aminomethane (Tris) and 20% acetonitrile, and contained 5 mM SDS. A complete separation was obtained in 2.5 min with an efficiency of 250,000-500,000 plates/m.     

Micelle to trapping solution stacking in micellar electrokinetic chromatography

An analytical strategy micelle to trapping solution stacking (MSS) was developed in acidic buffer in micellar electrokinetic chromatography (MEKC). The stacking mechanism is based on the transport, release, capturing of molecules bound to micelle carriers that are made to collapse into trapping solution (TS) to serve as the medium to contain and stacking the analytes. Tetrandrine and fangchinoline were selected as model mixture using sodium dodecyl sulfate (SDS) micelles as carrier to demonstrate this stacking method. The experiments by MSS-MEKC were carried out and further compared with those by normal MEKC. The results reveal that 113–123-fold improvements in the detection sensitivity was obtained for the analytes, and separation and determination of tetrandrine and fangchinoline in Stephaniae tetrandrae S. Moore and Fengtongan capsules were finished under optimum conditions using the sample matrix containing 8.0 mM SDS and TS containing 50 mM H₃PO₄–55% (v/v) ethanol.     

Simultaneous determination of antioxidants, preservatives and sweeteners permitted as additives in food by mixed micellar electrokinetic chromatography.

A micellar electrokinetic chromatography method was developed to simultaneously analyse commonly used food additives. The additive mixture, comprising propyl gallate, octyl gallate, dodecyl gallate, butylated hydroxyanisole, butylated hydroxytoluene, tertiary butylhydroquinone, p-hydroxybenzoic acid methyl ester, p-hydroxybenzoic acid ethyl ester, benzoic acid, sorbic acid, saccharin, aspartame and acesulfame-K, was not resolved using single surfactant micellar systems consisting of sodium dodecyl sulfate (SDS), sodium cholate (SC) or sodium deoxycholate (SDC). The separation of these additives using mixed micellar systems, involving SDS/SC, SDS/SDC and SC/SDC, was investigated. Organic solvents were added to the mixed micellar phases to optimise the separation. The mixture was successfully separated using a 20 mM borate buffer with 35 mM SC, 15 mM SDS and 10% methanol added at pH 9.3. Additives in cola beverages and low-joule jam were investigated and quantified using this method.     

On-chip chiral and achiral separation of amphetamine and related compounds labeled with 4-fluoro-7-nitrobenzofurazane

Amphetamine and analogous compounds have been labeled with 4-fluoro-7-nitrobenzofurazane and analyzed on a microfabricated chip. Separation of norephedrine, ephedrine, cathinone, pseudoephedrine, methcathinone, amphetamine and methamphetamine is demonstrated using micellar electrokinetic capillary chromatography (MEKC) and laser-induced fluorescence (LIF) detection. Chiral separations of individual drugs were studied using neutral and negatively charged cyclodextrins (CDs) with and without the addition of an organic modifier and/or sodium dodecyl sulfate (SDS). The best results were obtained using a highly sulfated gamma-CD (HS-gamm-CD) in combination with a low concentration of SDS. To obtain complete separation of a mixture of (+/-)-norephedrine, (+/-)ephedrine, (+/-)-pseudoephedrine, (+/-)-methcathinone, (+/-)-amphetamine and (+/-)-methamphetamine it was necessary to add a small amount (1.5 mM) of SDS to the separation buffer. Optimized chiral separation was achieved within 7 min using an S-folded separation channel, a separation voltage of 8 kV and a buffer consisting of 50 mM phosphate (pH 7.35), 10 mM HS-gamma-CD and 1.5 mM SDS.     

Microemulsion electrokinetic chromatography of proteins.

Microemulsion electrokinetic chromatography was used to separate a test mixture of proteins effectively. The separation was carried out in a 42.5 cm (to the detector) x 50 microns I.D. fused-silica capillary using a microemulsion system consisting of 80 mM heptane, 120 mM SDS, 900 mM butanol in 2.5 mM borate buffer, pH 8.5-9.5. Optimum separation conditions were investigated with respect to the running voltage, temperature, pH and the composition of microemulsion. Results were compared with those obtained in micellar electrokinetic chromatography and capillary zone electrophoresis. The examined method is practical and successfully applied to the assay of genetically engineering pharmaceuticals, recombinant human granulocyte macrophage colony stimulating factor injection and recombinant human granulocyte colony stimulating factor injection.     

Nonaqueous capillary electrophoresis with laser-induced fluorescence detection: a case study of comparison with aqueous media

A novel method based on separation by nonaqueous capillary electrophoresis (NACE) combined with laser-induced fluorescence (LIF) detection was developed and compared with classic aqueous modes of electrophoresis in terms of resolution of solutes of interest and sensitivity of the fluorescence detection. Catecholamines derivatized with 4-chloro-7-nitro-2,1,3-benzoxadiazole (NBD-Cl) were chosen as test analytes for their subtle fluorescence properties. In aqueous systems, capillary zone electrophoresis (CZE) was not suitable for the analysis of test analytes due to complete fluorescence quenching of NBD-labeled catecholamines in neat aqueous buffer. The addition of micelles or microemulsion droplets into aqueous running buffer can dramatically improve the fluorescence response, and the enhancement seems to be comparable for micellar electrokinetic chromatography (MEKC) and microemulsion electrokinetic chromatography (MEEKC). As another alternative, NACE separation was advantageous when performing the analysis under the optimum separation condition of 20 mM sodium tetraborate, 20 mM sodium dodecyl sulfate (SDS), 0.1% (v/v) glacial acetic acid, 20% (v/v) acetonitrile (ACN) in methanol medium after derivatization in ACN/dimethyl sulfoxide (DMSO) (3:2, v/v) mixed aprotic solvents containing 20 mM ammonium acetate. Compared with derivatization and separation in aqueous media, NACE-LIF procedure was proved to be superior, providing high sensitivity and short migration time. Under respective optimum conditions, the NACE procedure offered the best fluorescence response with 5-24 folds enhancement for catecholamines compared to aqueous procedures. In addition, the mechanisms of derivatization and separation in nonaqueous media were elucidated in detail.     

Methodology for predicting the separation of proteins by hydrophobic interaction chromatography and its application to a cell extract

Ligand-exchange micellar electrokinetic capillary chromatography was used for the chiral resolution of underivatized and dansyl amino acid enantiomers simultaneously. The separation was achieved by chiral copper(II)-L-valine complexes incorporated in micelles of sodium dodecyl sulfate (SDS). The enantioresolution was strongly affected by SDS and a concentration of 20 mM SDS was shown to be necessary for the separation. Other impacting factors were investigated including pH, the molar ratio of copper(II) to L-valine and the total concentration of complex. Using the proposed method, 11 different dansyl amino acids and two underivatized amino acids were separated successfully with a running electrolyte of 20 mM NH4OAc, 4 mM CuSO4, 8 mM L-valine and 20 mM SDS at pH 9.0 in less than 25 min. Experiments were also performed with other amino acid ligands in order to vary the stability and the sterical arrangement of the copper(II) complexes and the possible chiral recognition mechanism was also discussed briefly.     

Analysis of combinatorial chemistry samples by micellar electrokinetic chromatography

A micellar electrokinetic chromatography (MEKC) method has been developed that can evaluate the purity of samples generated in combinatorial chemistry libraries. This method uses an open tube capillary (27 cm x 50 microm) along with a run buffer composed of sodium dodecyl sulfate (SDS), hydroxypropyl-beta-cyclodextrin, and sodium tetraborate coupled with UV detection. Neutral compounds and compounds that were insoluble in aqueous buffers could be analyzed under these conditions in approximately 3 min. The concentration of SDS and the concentration of hydroxypropyl-beta-cyclodextrin effected the separation. The affect on selectivity resulting from the addition of an organic modifier to the run buffer was examined. The low background absorbency of the run buffer made for easy detection of compounds that absorbed at low UV wavelengths. The quick analysis time made this suitable for analysis of combinatorial chemistry samples.