Highly dispersed sulfur in multi-walled carbon nanotubes for lithium/sulfur battery

A facile method is developed for homogeneous dispersion of sulfur (S) nanoparticles in multi-walled carbon nanotubes (MWCNTs). The process involves the modification of MWCNTs via oxidation catalyzed by acid and the introduction of sulfur nanoparticles into the MWCNTs through direct precipitation. The resulting sample (precipitated S/MWCNTs) is characterized with scanning electron microscopy and thermogravimetric analysis, and its performance as cathode of lithium/sulfur battery is investigated with a comparison of the sample prepared by ball-milling (ball-milling S/MWCNTs). It is found that the precipitated S/MWCNTs exhibit better battery performance than the ball-milling S/MWCNTs. The initial discharge capacity is 1,299 mA?h?g^?1 for the precipitated S/MWCNTs but only 839 mA?h?g^?1 for ball-milling S/MWCNTs at 0.02 C. The capacity remains 800 mA?h?g^?1 for the precipitated S/MWCNTs but only 620 mA?h?g^?1 for ball-milling S/MWCNTs at 0.05 C after 50 cycles. The better performance of the precipitated S/MWCNTs results from the improved uniformity of S dispersed in MWCNTs through precipitation.     

Activated carbon aerogels with high bimodal porosity for lithium/sulfur batteries

Activated carbon aerogels (ACAs) with high bimodal porosity were obtained for lithium/sulfur batteries by potassium hydroxide (KOH) activation. Then sulfur–activated carbon aerogels (S–ACAs) composites were synthesized by chemical deposition strategy. The S–ACAs composites were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy, and N₂ adsorption/desorption measurements. It is found that the activated carbon aerogels treated by KOH activation presents a porous structure, and sulfur is embedded into the pores of the ACAs network-like matrix after a chemical deposition process. The Li/S–ACAs (with 69.1 wt% active material) composite cathode exhibits discharge capacities of 1,493 mAh g^?1 in the first cycle and 528 mAh g^?1 after 100 cycles at a higher rate of C/5 (335 mA g^?1). The S–ACAs composite cathode exhibits better electrochemical reversibility, higher active material utilization, and less severe polysulfide shuttle than S–CAs composite cathode because of high bimodal porosity structure of the ACAs matrix.     

Synthesis and electrochemical performance of sulfur–carbon composite cathode for lithium–sulfur batteries

In this paper, porous carbon was synthesized by an activation method, with phenolic resin as carbon source and nanometer calcium carbonate as activating agent. Sulfur–porous carbon composite material was prepared by thermally treating a mixture of sublimed sulfur and porous carbon. Morphology and electrochemical performance of the carbon and sulfur–carbon composite cathode were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectra (EIS), and galvanostatic charge–discharge test. The composite containing 39 wt.% sulfur obtained an initial discharge capacity of about 1,130 mA?h g^?1 under the current density of 80 mA?g^?1 and presented a long electrochemical stability up to 100 cycles.     

Multi-walled carbon nanotubes used as support for lipase from <Emphasis Type="Italic">Burkholderia cepacia</Emphasis>

Commercial lipase from Burkholderia cepacia is immobilized on functionalized multi-walled carbon nanotubes (MWNT-COOH and MWNT-OH) provided by a physical adsorption. The immobilization processes for the carbon nanotubes are defined using immobilization time (0–30 min) and distinct adsorbent:adsorbate ratios (1:4, 1:7, and 1:10) with lipase loading of 100, 175, and 250 mg, respectively. The characterization of the immobilized preparations, the free lipase, and the pure nanotubes (MWNT-COOH and MWNT-OH) indicate that the lipase adsorption is increased. Thermogravimetric analysis, differential scanning calorimetry, and scanning electron microscopy are used. The specific surface area, pore volumes, and average pore diameters are determined by nitrogen adsorption–desorption isotherms. For the pure lipase, in the range between 40 and 300 °C, the micrograph is acquired. Experimental results clearly show an effective lipase adsorption in a lower period of time (5 min) in MWNT-COOH and MWNT-OH as well as a decrease in the surface area (98.30–45.9(86)?±?2.5 and 97.61–37.71?±?3.3(7) m² g^?1) and the pore volume (0.48–0.25?±?0.01 and 0.39–0.24?±?0.05 cm³ g^?1), indicating that functionalized multi-walled carbon nanotubes can be successfully used as enzyme support.     

Novel multi-sorbent for sampling and determination of trace volatile organic sulfur compounds in ambient air

Novel adsorbent APSG-MW (average particle size 215?µm and specific surface 98 m²?g^?1) bonding multi-walled carbon nanotubes (MWCNTs) on silica gel are obtained. Then the sampling tubes filled with Tenax TA and APSG-MW are prepared and the adsorptive capacity of Tenax TA/APSG-MW for volatile organic sulfur compounds (VOSCs) is studied. The data show that the adsorption and desorption recoveries of multi-sorbent for VOSCs are satisfactory (>85%), and the breakthrough values are large (>16?L?g^?1) enough to absorb VOSCs in ambient air. The sampling precision of the sorbent tubes meets TO-17 criteria. The sampling tubes are successfully used to concentrate and analyze a sample of landfill air, and the major S compounds are identified.     

Synthesis of micro- and mesoporous carbon spheres for supercapacitor electrode

Micro- and mesoporous carbon spheres (MMCSs) are synthesized by the polymerization of colloidal silica-entrapped resorcinol/formaldehyde in the presence of ammonia as catalyst, followed by carbonization, sodium hydroxide (NaOH) etching to remove silica template, and potassium hydroxide (KOH) activation. The morphology and microstructure are characterized by scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption–desorption. The results show that a typical sample (denoted as MMCS-3) unites the characteristics of regular spherical shape (uniform diameters of 500 nm), high specific surface area (1,620 m² g^?1), large pore volume (1.037 cm³ g^?1), and combined micropores and mesopores (11.0 nm), which endows MMCS-3 good electrochemical performance. MMCS-3 as supercapacitor electrode shows a specific capacitance of 314 F g^?1 under a current density of 0.5 A g^?1 and low internal resistance of 0.2 Ω in 6 M KOH aqueous solution. The electrochemical capacitance still retains 198 F g^?1 at a high current density of 10 A g^?1. After 500 cycle numbers of galvanostatic charge/discharge at 0.5 A g^?1, MMCS-3 electrode still remains the specific capacitance of 301 F g^?1 with the retention of 96 %. This study highlights the potential of well-designed MMCSs as electrodes for widespread supercapacitor applications.     

Carbon electrode modified with ionic liquid and multi-walled carbon nanotubes for voltammetric sensing of adenine

A voltammetric sensor was fabricated by applying a Nafion and multi-walled carbon nanotubes (MWCNTs) composite film on the surface of a carbon ionic liquid electrode (CILE), which was prepared by mixing 1-butyl-3-methylimidazolium hexafluorophosphate with graphite powder. The electrochemical behavior of adenine on the Nafion-MWCNTs/CILE was investigated in pH 5.5 buffer solution. Adenine showed an irreversible adsorption-controlled oxidation reaction with enhanced electrochemical response, which was due to the presence of high conductive MWCNTs on the CILE surface. The electrochemical parameters of adenine electro-oxidation were determined, and the experimental conditions were optimized. Under the optimal conditions, the oxidation peak current was linear to the adenine concentration over the range of 1.0?×?10^?7 to 7.0?×?10^?5 mol L^?1 with a detection limit of 3.3?×?10^?8 mol L^?1 (signal/noise?=?3). The electrode showed good stability and selectivity, and was further applied to milk powder samples with satisfactory results.     

Nanofibers of V<Subscript>2</Subscript>O<Subscript>5</Subscript>/C@MWCNTs as the cathode material for lithium-ion batteries

Vanadium pentoxide (V₂O₅) nanofibers (NFs) with a thin carbon layer of 3–5 nm, which wrapped on V₂O₅ nanoparticles, and integrated multiwalled carbon nanotubes (MWCNTs) have been fabricated via simple electrospinning followed by carbonization process and post-sintering treatment. The obtained composite displays a NF structure with V₂O₅ nanoparticles connected to each other, and good electrochemical performance: delivering initial capacity of 320 mAh g^?1 (between 2.0 and 4.0 V vs. Li/Li⁺), good cycling stability (223 mAh g^?1 after 50 cycles), and good rate performance (~?150 mAh g^?1 at 2 A g^?1). This can attribute to the carbon wrapped on the V₂O₅ nanoparticles which can not only enhance the electric conductivity to decrease the impendence of the cathode materials but also maintain the structural stability to protect the nanostructure from the corruption of electrolyte and the strain stress due to the Li-ion intercalation/deintercalation during the charge/discharge process. And, the added MWCNTs play the role of framework of the unique V₂O₅ coated by carbon layer and composited with MWCNT NFs (V₂O₅/C@MWCNT NFs) to ensure the material is more stable.     

Copper sulfide nanoneedles on CNT backbone composite electrodes for high-performance supercapacitors and Li-S batteries

Hierarchical-structured copper sulfide nanoneedles were grown on multi-walled carbon nanotube backbone (denoted as CuS@CNT) as electrodes for supercapacitors via a facile template-based hydrothermal conversion approach and further by simply impregnating sulfur into CuS@CNT (S@CuS@CNT) as electrodes for Li-S batteries. The electrochemical measurements showed that the resultant CuS@CNT composite electrodes deliver outstanding electrochemical performance with a specific capacitance up to 566.4 F g^?1 and cyclic stability of 94.5 % of its initial capacitance after 5000 cycles at a current density of 1 A g^?1. A synergistic effect arising from the unique hierarchical structure was responsible for the electrode performance, including a large surface area of 49.3 m² g^?1 and active CuS ultrafine nanoneedles firmly bonded to the highly conductive carbon nanotube (CNT) backbone. When used as an electrode material for Li-S batteries, the S@CuS@CNT (S content 59 wt%) exhibited satisfying electrochemical performance. The S@CuS@CNT electrode showed that coulombic efficiency was close to 100 % and capacity maintained more than 500 mA h g^?1 with progressive cycling up to more than 100 cycles even at a high current density. This strategy of stabilizing S with a small amount of copper sulfide nanoneedles can be a very promising method to prepare free-standing cathode material for high-performance Li-S batteries. The fabrication strategy presented here is low cost, facile, and scalable, which can be considered as a promising material for large-scale energy storage device. In particular, the use of CNT as backbone for the growth of active materials presents many potential merits owing to its lightweight, biodegradable, and stretchable characteristics.     

Mesoporous carbon/sulfur composite with N-doping and tunable pore size for high-performance Li-S batteries

Mesoporous carbons (MCs) were used as the matrixes to load sulfur for lithium sulfur (Li-S) batteries, and pore sizes were tuned by heat treatment at different high temperatures. The cathode material shows the highest discharge capacity of 1158.2 mAh g^?1 at the pore size of 4.1 nm among as-prepared nitrogen-free materials with different sizes. Meanwhile, the nitrogen doping of mesoporous carbon helps to inhibit the diffusion of polysulfide species via an enhanced surface adsorption. The carbon/sulfur containing N (4.56%) shows a high initial discharge capacity of 1315.8 mAh g^?1 and retains about 939 mAh g^?1 after 100 cycles at 0.2 C. The improved electrochemical performance is ascribed to the proper pore size, surface chemical property, and conductivity of the N-doped carbon material.     

A comparison of sulfur loading method on the electrochemical performance of porous carbon/sulfur cathode material for lithium–sulfur battery

To get a high sulfur loaded porous carbon/sulfur cathode material with an excellent performance, we investigated four different sulfur loading treatments. The samples were analyzed by the Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD) patterns, thermal gravimetric analysis (TGA), and scanning electron microscopy (SEM). We proved that it is more effective to introduce the sulfur into the pores of porous carbon at 300 °C than at 155 °C. Especially, the porous carbon/sulfur composite heated in a sealed reactor at 300 °C for 8 h presents a fine sulfur load with sulfur content of 78 wt.% and exhibits an excellent electrochemical performance. The discharge capacity is 760, 727, 744, 713, and 575 mAh g^?1 of sulfur at a current density of 80, 160, 320, 800, and 1,600 mA g^?1 based on the sulfur/carbon composite, respectively. What is more, there is almost no decay at the current density of 800 mA g^?1 for 50 cycles and coulombic efficiency remains over 95 %.     

Preconcentration of ultra-trace amounts of iron and antimony using ion pair solid phase extraction with modified multi-walled carbon nanotubes

Ion pair solid phase extraction was applied to the simultaneous preconcentration of iron and antimony. The ion pairs consisting of FeCl₄ ^? or SbCl₄ ^? anions and the benzyldimethyltetradecyl ammonium cation were formed on the surface of multi-walled carbon nanotubes, then eluted with nitric acid, and the elements finally quantified by ETAAS. The adsorption capacities of the impregnated MWCNTs are 9.2 mg g^?1 for iron and 27.5 mg g^?1 for antimony. The following analytical figures of merit were determined for iron and antimony, respectively: Enrichment factors of 210 and 230, assay precisions of ±5.3 % and ±4.8 %, linear calibration plots from 0.7 to 9.4 and 13.0 to 190 ng L^?1, and detection limits of 0.17 and 3.5 ng L^?1. The method was applied to the determination of iron and antimony in human hair, synthetic sample, and to the certified reference materials gold ore (MA-1b) and trace elements in water (SRM 1643d).

Solid-phase extraction based on multi-walled carbon nanotube (MWCNT) sorbents combined with bio-coacervation extraction for the determination of atrazine from water samples followed by HPLC analysis

In this study, combined technique of solid-phase extraction based on multi-walled carbon nanotubes with bio-coacervation extraction (SPE-MWCNT-BCAE) has been developed as a new sample preparation method for the determination of atrazine from water samples. The proposed method involves two steps: analyte enrichment on the solid sorbent and subsequently elution of the analyte by an appropriate solvent. Multi-walled carbon nanotubes (MWCNTs) were used as the sorbent. They have high specific surface area, nano-scale structure and high diffusion rate. The second step is based on the use of bioaggregates for analyte re-enrichment, which consists of biosurfactants and ionic liquid. This method follows the principles of green chemistry. Parameters affecting the extraction efficiency were optimized. Under optimum conditions, the enrichment factor was 176. The linear dynamic range (LDR) and limit of detection (LOD) were 2–100 µg L^?1 and 0.66 µg L^?1, respectively. The relative standard deviation (RSD) for six replicate measurements was 3.8%. The method was applied to the determination of ultratrace levels of atrazine in environmental water samples with satisfactory results.     

Preparation of NiO/multiwalled carbon nanotube nanocomposite for use as the oxygen cathode catalyst in rechargeable Li–O2 batteries

NiO/multiwalled carbon nanotube (NiO/MWCNT) nanocomposites have been prepared and used for a Li–O₂ battery cathode catalyst. Electrochemical measurements demonstrate that the batteries with NiO/MWCNT catalyst have a discharge capacity of 2,500 mAh g^?1, a charge capacity of 2,100 mAh g^?1, and a rechargeable ability performing better than Ketjenblack (KB) and MWCNTs. KB has the largest discharge capacity (2,700 mAh g^?1) due to the highest surface area and pore volume but the worst charging behavior due to poor mass transport in the small-width pore (2.48 nm). MWCNTs have a much better charging performance owing to a larger pore width (8.93 nm) than carbon black. NiO/MWCNTs have the largest charge capacity because of the facilitated mass transport in the comparatively large pores (7.68 nm) and the increased catalytic ability produced by the NiO nanoparticles. These improvements are also responsible for the best cycle and rate performances of the nanocomposites among the three catalysts.     

Synthesis of spherical porous carbon by spray pyrolysis and its application in Li-S batteries

A spherical porous carbon (SPC) with high specific surface area is prepared by spray pyrolysis at 800 °C followed by removing silica template. The prepared SPC is employed as a conductive matrix in the sulfur cathode (S-SPC) for lithium–sulfur secondary batteries. The BET surface area of the prepared SPC sample is as high as 1,133 m² g^?1 and the total pore volume is 2.75 cm³ g^?1. The electrochemical evaluations including charge–discharge tests, cyclic voltammograms (CV), and electrochemical impedance spectrum suggest that the prepared S-SPC composite presents superior electrochemical stability when compared to the S-SP cathode. The as-prepared S-SPC composite shows improved cycle performance. The reversible discharge capacity is about 637 mAh g^?1 after 50 cycles, which is much better than that of the as-prepared sulfur–Super P carbon black composite. It may be attributed to the high porosity and excellent conductive structure of the SPC.     

Electrochemical determination of bisphenol A based on PHD/MWCNTs modified glassy carbon electrode

A novel electrochemical sensor for the determination of bisphenol A (BPA) was fabricated by block polyelectrolyte composite films, which composed of diblock polyelectrolyte poly (2-hydroxyethyl methacrylate)-b-poly (2-(dimethylamino) ethyl methacrylate) (PHEMA-b-PDMAEMA, noted as PHD in the later content) and multi-walled carbon nanotubes (MWCNTs). The tertiary amino groups of PDMAEMA can be protonated at physiological pH. The protonated PDMAEMA can thus interact with the negatively charged BPA through electrostatic attraction to increase the BPA sorption capacity and enhance the ability for highly sensitive detection of BPA. The PHD/MWCNTs composite films combine the electrocatalytic property of MWCNTs and the electrostatic attraction of protonated PHD. Because of the above-mentioned excellent property of the composite films, the PHD/MWCNTs/glassy carbon electrode exhibited good electrocatalytic activity to electrooxidation of BPA. The wide linear response range of the BPA sensor was from 4.56 × 10^?5 g L^?1 to 2.28 × 10^?2 g L^?1 with a lower detection limit of 2.28 × 10^?6 g L^?1 (S/N = 3) and high sensitivity 2442.86 μA L g^?1 cm^?2. The current reached the steady-state current with a shorter response time less than 4 s. The proposed method was successfully applied to determine BPA in real samples (PVC food package, milk, tap water and pond water) and satisfactory results were obtained. These results indicated that the block polyelectrolyte composite have potential applicability of the BPA sensor.     

Synthesis and electrochemical characterization of duo doped spinels (zinc and praseodymium) for use in lithium rechargeable batteries

LiMn₂O₄ and LiZn_xPr_yMn_2?x?yO₄ (x = 0.10–0.24; y = 0.01–0.10) powders have been synthesized by sol–gel method using palmitic acid as chelating agent. The synthesized samples have been subjected to thermo gravimetric and differential thermal analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray analysis (EDAX). The sol–gel route bestows low calcination temperature, shorter heating time, high purity, good control over stoichiometry, small particle size, high surface area, good surface morphology and better homogeneity, The XRD patterns reveal high degree of crystallinity and better phase purity. SEM and TEM images exhibit nano-sized nature particles with good agglomeration. EDAX peaks of Zn, Pr, Mn and O have been confirmed in actual compositions of LiMn₂O₄ and LiZn_xPr_yMn_2?x?yO₄. Charge–discharge studies of pristine spinel LiMn₂O₄ heated at 850 °C delivers discharge capacity of 132 mA h g^?1 corresponding to columbic efficiency of 73 % during the first cycle. At the end of 10th cycles, it delivers maximum discharge capacity of 112 mA h g^?1 with columbic efficiency of 70 % and capacity fade of 0.15 mA h g^?1 cycle^?1 over the investigated 10 cycles. Inter alia, all dopants concentrations, LiZn_0.10Pr_0.10Mn_1.80O₄ exhibits the better cycling performance (1st cycle discharge capacity: 130 mA h g^?1 comparing to undoped spinel 132 mA h g^?1) corresponding to columbic efficiency of 73 % with capacity fade of 0.12 mA h g^?1 cycle^?1.     

Metal-free boron-doped carbon microspheres as excellent cathode catalyst for rechargeable Li–O<Subscript>2</Subscript> battery

Rechargeable Li–O₂ batteries are attracting more and more interest due to their high energy density. Meanwhile, the replacement of high-cost and scarce precious-metal catalysts has attracted more and more attention. Currently, many academic researchers have paid attention to find highly efficient metal-free catalysts as air cathode material. Herein, the boron-doped carbon microspheres (B-CMs) were prepared through a novel and facile static calcination method and showed high electrocatalytic activity as a cathode material. The battery with a B-CM cathode delivered a high initial discharge capacity of 13,757.2 mAh g^?1 and outstanding coulombic efficiency of 90.1 % at 100 mA g^?1. In addition, stable cyclability (151 cycles with stable discharge voltage of ~2.60 V with a cutoff capacity of 1000 mAh g^?1 at 200 mA g^?1) has been exhibited. These performances are due to three main points: boron carbide compound changed the surface area of the CMs and formed the mesopore architectures as well as the large surface area of 683.738 m² g^?1; the reduce of boron atom can slow down the oxidation of the CMs during the cyclings; and finally, the electron-deficient boron atom introduction greatly facilitated Li⁺ diffusion and electrolyte immersion and enhanced the oxygen reduction and evolution reaction kinetics.     

Facile Synthesis of Nitrogen‐Containing Mesoporous Carbon for High‐Performance Energy Storage Applications

Porous carbon with high specific surface area (SSA), a reasonable pore size distribution, and modified surface chemistry is highly desirable for application in energy storage devices. Herein, we report the synthesis of nitrogen‐containing mesoporous carbon with high SSA (1390 m² g^?1), a suitable pore size distribution (1.5–8.1 nm), and a nitrogen content of 4.7 wt % through a facile one‐step self‐assembly process. Owing to its unique physical characteristics and nitrogen doping, this material demonstrates great promise for application in both supercapacitors and encapsulating sulfur as a superior cathode material for lithium–sulfur batteries. When deployed as a supercapacitor electrode, it exhibited a high specific capacitance of 238.4 F g^?1 at 1 A g^?1 and an excellent rate capability (180 F g^?1, 10 A g^?1). Furthermore, when an NMC/S electrode was evaluated as the cathode material for lithium–sulfur batteries, it showed a high initial discharge capacity of 1143.6 mA h g^?1 at 837.5 mA g^?1 and an extraordinary cycling stability with 70.3 % capacity retention after 100 cycles.     

The production of activated carbon from cation exchange resin for high-performance supercapacitor

High-performance activated carbon for electrochemical double-layer capacitors (EDLC) has been prepared from cation exchange resin by carbonization and subsequent activation with KOH. The activation temperature has a key role in the determination of porous carbon possessing high surface areas, and large pore structures. The porous carbon activated at 700 °C (carbon-700-1:4) has high surface area (2236 m²?g^?1) and large total pore volume (1.15 cm³?g^?1), which also displays best capacitive performances due to its well-balanced micro- or mesoporosity distribution. In details, specific capacitances of the carbon-700-1:4 sample are 336.5 F?g^?1 at a current density of 1 A?g^?1 and 331.8 F?g^?1 at 2 A?g^?1. At high current density as 20 A?g^?1, the retention of its specific capacitance is 68.4 %. The carbon-700-1:4 sample also exhibits high performance of energy density (46.7 Wh?kg^?1) and long cycle stability (～8.9 % loss after 3,000 cycles). More importantly, due to the amount of waste ion-exchange resins increasing all over the world, the present synthetic method might be adopted to dispose them, producing high-performance porous carbons for EDLC electrode materials.