L-R两步欧拉方法在铝材料微喷射中的应用

应用三维弹塑性流体力学Lagrangian-Remapping两步欧拉计算方法对铝材料微喷射现象进行了数值模拟研究。计算了Asay实验中表面刻有相同深度、不同夹角沟槽的金属铝微喷射模型,计算得到的微喷物总质量、最大射流速度和实验结果均符合较好。进一步展开了对相同深度、更大夹角范围沟槽微喷射的数值模拟。分析认为喷射最大速度随沟槽角度的增大呈线性下降趋势。同时给出了喷射系数随沟槽角度的变化的拟合关系曲线,看到由于材料强度及沟槽角度变化后造成的波系关系变化的影响,随着沟槽角度增加,喷射系数曲线呈明显非线性发展。     

冲击作用下金属表面微喷射的分子动力学模拟

利用二维分子动力学程序,结合类紧束缚杂化多体势,研究冲击载荷下金属表面包含沟槽型缺陷的微喷射动力学过程.在产生微喷射以后,结果表明材料内部传播着两种波系:反射稀疏波和二次加载压缩波,其中,反射稀疏波波面与沟槽形状相似,而二次压缩波波面随沟槽夹角的变化而变化;并形成了两个压强区:负压区和正压区,负压区的存在表明材料中可能产生微损伤.同时,统计结果表明微喷射体的速度随沟槽半角增加而增加的趋势,微喷射体的粒子数随沟槽半角增大而减少的趋势,当沟槽半角大于60°,微喷射效应消失.以上计算结果可以定性说明射流是沟槽型 关键词： 冲击波 沟槽型缺陷 微喷射 分子动力学     

加载波前沿宽度对铝表面微射流的影响

利用光滑粒子流体动力学方法,计算了金属表面沟槽在冲击下的微射流现象,详细讨论了微射流对加载波前沿宽度的依赖性. 计算结果表明：随加载波前沿宽度增加, 射流质量和头部速度都减小,同时低速喷射物所占比例增大. 对结果分析得出,微射流由沟槽斜面粒子在冲击加卸载后获得轴向速度,并在对称轴附近碰撞形成;射流体由沟槽斜面的金属薄层构成;当加载波前沿变宽,形成射流的金属层变小,这是由于沟槽斜面粒子的碰撞速度降低,碰撞角度增大,部分粒子碰撞时不满足射流强度封锁条件,而不再形成射流. 关键词： 微射流 光滑粒子方法 加载波前沿     

冲击压力及加载速率对沟槽微射流的影响

通过二维弹塑性流体力学欧拉程序MEPH,系统研究冲击压力及加载速率对沟槽微射流喷射量的影响.计算结果显示,微射流的喷射量随冲击压力的增大而增大,但喷射量对压力的变化并不敏感;计算结果和实验结果均表明,加载速率对沟槽微射流的喷射量有较大影响,随着加载速率的减小,微粒子喷射量大致按指数规律减少,所得数值计算结果得到实验验证.     

爆轰驱动金属飞层对碰凸起和微射流形成的数值模拟研究

本文对柱面两极点起爆情况下滑移爆轰波驱动两层金属飞层对碰凸起和微射流形成进行了模拟研究. 铅飞层内界面走时计算结果与实验结果能够较好符合. 在两极位置铅飞层内部出现断裂并形成空腔, 内壁面则形成鼓包型凸起; 在赤道位置飞层内壁面凸起后断裂产生大尺度金属颗粒, 其和微喷射形成的小尺度颗粒叠加构成了对碰区凸起现象. 在铅飞层内表面微喷射现象的研究中发现, 两极附近的微喷物质最大速度逐渐下降, 而对碰区附近的微喷颗粒最大速度反而随时间逐渐增高. 之后, 通过设计沟槽型微喷计算模型, 验证了在两极和赤道上铅飞层内表面产生的初始微喷射最大速度能够由同一均匀缺陷表面所产生. 最后, 通过数值模拟分析研究初步给出了该问题中抑制金属飞层对碰凸起和微喷现象的方法.     

缺陷形状对铝材料微喷射的影响

通过二维弹塑性流体力学欧拉程序MEPH,对包含不同形状不同角度缺陷铝材料的微射流现象进行数值模拟,并对其最大喷射速度以及喷射系数进行数值统计,得到不同形状、不同角度缺陷最大喷射速度及喷射系数的变化规律.并将计算结果与实验结果进行比较,基本吻合,能够反映试验规律.     

运动状态下聚能战斗部侵彻披挂反应装甲靶板的数值模拟

运用LS-DYNA有限元程序模拟了不同横向飞行速度(150、200、300、400、500m/s)和侵彻角度(30°、45°、60°)情况下聚能战斗部对披挂反应装甲后效靶板的侵彻过程,讨论了射流所受干扰情况及其对后效靶板的侵彻结果。研究结果表明:当侵彻角度一定时,射流对靶板表面的切割长度随速度的增大而增大,且在侵彻角度为30°时增大速率最快;但射流侵彻深度随速度的增大而减小,且在侵彻角度为60°时减小速率最慢。当飞行速度一定时,射流对靶板表面的切割长度和侵彻深度均随侵彻角度的增大而减小,且表面切割长度降幅随速度的增大呈先增大后减小的趋势,在速度为300m/s时,降幅最大,为59.6%;而侵彻深度降幅随速度的增大呈先减小后增大的趋势,在速度为350m/s时,降幅最小,为39.3%。最后通过理论方法分析了数值模拟结果,论证了数值模拟方法的正确性。     

射流抛光中的流场特性研究

为了给出射流抛光系统的优化设计参数,从理论上分析了冲击射流流场的结构特点,建立了工件壁面上的速度、压强与冲击角度、射流出口速度以及冲击距离的数学关系。就不同参数对射流流场分布的影响进行了定量计算,结果表明,工件壁面上的压强和速度与出口压强和速度成线性正比关系。当冲击距离大于9.6d(d为射流喷口的直径)时,工件壁面压强和速度随冲击距离的增大而减小,冲击距离增加到15d时,壁面压强最大值减小到0.54p0(p0为射流出口处的压强)。工件壁面压强和速度随冲击角度的减小而减小,当入射角为90°、60°和45°时,分别得到壁面压强最大值ps=0.95 p0,0.74p0,0.475p0,上游速度最大值um02=0.96u0,0.8u0,0.67u0(u0为射流出口处的速度)。     

冲击诱导金属铝表面微射流现象的微观模拟

采用嵌入原子势分子动力学模拟方法, 研究了金属铝表面沟槽在冲击下形成微射流的微观过程和动力学性质. 通过对模拟结果的统计分析, 获得了较宽冲击压力范围内微射流形态的变化规律, 以及相应的质量-空间分布和质量-速度分布变化. 基于原子中心对称参数, 分析了样品近表面非晶态转变和卸载熔化过程, 获得了卸载熔化对微射流质量及其分布的影响规律. 研究还发现: 样品熔化之前, 微射流质量与波后粒子速度呈线性增加关系; 卸载熔化出现后, 微射流质量开始迅速增加; 当卸载熔化速度足够快时, 金属强度效应可忽略, 此时微射流质量与波后粒子速度再次表现出线性增加关系.     

SPH方法对金属表面微射流的数值模拟

 光滑粒子流体动力学（Smoothed Particle Hydrodynamics）方法是一种无网格的拉氏计算方法,具有计算格式简单、易于计算大变形问题等优势。用二维SPH程序模拟了冲击加载下金属铝表面的沟槽状缺陷产生微射流的过程,得到了喷射物的总质量、最大速度和质量-速度曲线。还计算了相同深度、不同夹角的沟槽微射流,并与实验结果进行了比较。结果表明：计算得到的喷射物总质量和最大速度与实验结果符合较好,SPH方法对于估算金属表面的微射流提供了一种有效的数值模拟手段。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.