铈掺杂钆镓铝石榴石相玻璃陶瓷的光学及光谱参数

根据X射线衍射图谱对铈掺杂的钆镓铝石榴石相玻璃陶瓷的晶体结构进行分析,采用直径10英寸积分球结合CCD(charge coupled device)探测器系统,对蓝色半导体发光二极管激发下铈掺杂钆镓铝石榴石相玻璃陶瓷的荧光光谱进行测试,解析出样品发光的绝对光谱功率分布,推导出光量子数分布,求得荧光量子产率和组合白光的色坐标及其相关色温。结果表明,所调查的铈掺杂钆镓铝石榴石相玻璃陶瓷在蓝光LED激发下的荧光量子产率为29.2%,所获得组合白光的色坐标x=0.319,y=0.349,相关色温为6 086K。尽管该混晶陶瓷的荧光量子产率稍小于铈掺杂YAG玻璃陶瓷,但其与蓝光LED组合后发光的色温也明显低于后者,从而为舒适型LED照明玻璃陶瓷的进一步优化提供了新思路。     

连续可调宽光谱荧光玻璃的制备及性能

宽带荧光转换发光二极管(LED)用荧光玻璃具有良好的热稳定性和光学性质,可以避免传统的有机树脂封装荧光粉方案中存在的热稳定性差和重吸收问题,提高LED的使用寿命和发光效率。本文采用熔融淬冷法制备了一种连续可调宽光谱的Ce~(3+)/Mn~(2+)共掺氟硅酸盐玻璃,并对其发光性能进行了研究。为了探究Ce~(3+)/Mn~(2+)之间的能量传递,分别制备了掺Ce~(3+)、掺Mn~(2+)氟硅酸盐玻璃作为比对。结果表明,在紫外光激发下,可以观察到Ce~(3+)对Mn~(2+)发光的敏化现象,分别由掺Ce~(3+)荧光玻璃的蓝光发射和掺Mn~(2+)荧光玻璃的黄色发射,拓展为Ce~(3+)/Mn~(2+)共掺荧光玻璃的白光宽光谱发射,范围为380～780 nm;对比掺Mn~(2+)的荧光玻璃,Ce~(3+)/Mn~(2+)共掺荧光玻璃中Mn~(2+)的发光强度提升了3倍;随着Mn~(2+)浓度从0.8%增加到2.0%,Ce~(3+)向Mn~(2+)的能量传递效率从12.5%提升至24.2%。此外,通过调节紫外激发波长(353～369 nm),实现了从蓝光到红光区域的连续可调宽带发射。这种新型Ce~(3+)/Mn~(2+)共掺玻璃有望替代目前常规的多组分荧光粉LED光源应用于分光光度计、荧光光谱仪等光学领域。     

不同激发波长下Ce~(3+)-Tb~(3+)-Sm~(3+)共掺白光玻璃的发光性能

本文采用高温熔融技术制备了Ce3+-Tb3+-Sm3+三种离子共掺杂的硼硅酸盐透明玻璃.测试了紫外LED激发下Ce3+离子、Tb3+离子及Sm3+离子单掺与共掺样品的激发光谱及荧光光谱,通过对单掺及共掺样品荧光寿命的测试研究了Ce3+离子、Tb3+离子及Sm3+离子在玻璃基质中的能量传递机理.通过调整紫外LED灯的激发波长调整发光样品所发射光谱的色度坐标、显色指数及色温,得到适合人类生活、学习、工作的白光发光.     

可调白光发射的Ce-Tb-Eu共掺钙硼硅酸盐发光玻璃

采用高温熔融法制备了Eu单掺和Ce-Tb-Eu共掺的钙硼硅酸盐发光玻璃。使用荧光分光光度计测量了样品的发射与激发光谱,并通过激发、发射光谱和CIE色度坐标对其发光特性进行了研究。结果表明:改变玻璃基质提高其光学碱度,可以大幅度增加Eu³⁺/Eu²⁺比例,增强Eu³⁺的红光发射。在378 nm单色光激发下,Ce-Tb-Eu共掺发光玻璃的发射光谱中同时观测到了蓝光、绿光和较强的红光特征峰。通过调节Tb、Eu的比例,可以使样品发射光谱的色坐标在白光区域内变化,实现白光调控。     

白光LED用新型Ce,Pr掺杂的YAG单晶荧光材料的光谱性能研究

为了改善白光LED用荧光材料效率低、均匀性差、光衰大、寿命短及物化性能差等不足,本文采用单晶荧光材料取代荧光粉来制备白光LED,并对白光LED用新型YAG单晶荧光材料的制备和光谱性能进行了研究.采用提拉法生长了白光LED用Ce∶YAG及Pr,Ce∶YAG晶体,并通过吸收光谱,激发、发射光谱对晶体材料的光谱特性进行表征.研究表明,Ce∶YAG单晶荧光材料可以被发射波长460 nm左右的蓝光芯片有效激发,产生一个范围为480~650 nm宽峰发射.通过Pr3+,Ce3+离子共掺杂可以有效补偿Ce3+离子单掺杂YAG荧光材料发光中的红色发光成分.     

高效氟磷酸盐玻璃白光荧光体制备及发光特性

采用熔融淬火方法制备了一系列Sn2+，Dy3+单掺及Sn2+-Dy3+共掺氟磷酸盐玻璃荧光体。利用紫外-可见分光光度计分别对各玻璃荧光体的透过光谱、激发光谱、发射光谱及荧光寿命等进行了测试和分析。结果发现在紫外光激发下，对于Sn2+、Dy3+单掺氟磷酸盐玻璃可分别获得高效的蓝光与黄光发射，且Sn2+单掺氟磷酸盐玻璃荧光体发光显色指数和量子效率最高；对于Sn2+-Dy3+共掺氟磷酸盐玻璃荧光体可实现高效的白光发射，且发现在Sn2+和Dy3+之间存在明显的能量传递，通过调节Dy3+掺杂浓度，两离子之间的能量转移效率亦随之改变，从而可对其白光色度进行调节。当Dy3+掺杂浓度为3 Wt%时，利用280 nm商用LED芯片激发可获得对应色坐标为(0.311，0.330)，量子效率为56.3%，亮度为6 706 cd·m-2的近纯白光发射。此外，对各类玻璃样品的DSC、导热及其他光学性能也进行了测试与计算，获得了各样品的热导率、量子效率、色坐标、显色指数等参数。研究结果表明，制备的高效氟磷酸盐玻璃完全有望作为可调谐白光发光荧光体应用于商用LED。     

基于荧光玻璃的高效LED白光技术

采用高温熔融法制备了一定质量比例的SiO_2-YAG∶Ce~(3+)片状荧光玻璃,厚度为0.2 mm,分析其XRD物相、光学和SEM微观结构、PL光谱。结果表明:荧光玻璃保留了晶相,荧光粉颗粒在玻璃基质中均匀分布,荧光玻璃和荧光粉的激发响应关系一致。在465 nm蓝光激发下,发射波长均在535 nm附近,表明荧光玻璃除含有玻璃相,还有荧光粉的物质结构特性。将不同波长蓝光芯片与不同荧光粉含量的荧光玻璃进行封装测试,结果表明:器件的流明效率可达到234.81 lm/W;色温和显色指数均随荧光粉含量增加而单调下降,呈现高色温和低显色指数;荧光粉质量分数从6%增加至15%时,不同波长激发下的色坐标x与y呈现大致相同的线性变化率。采用450 nm激光激发荧光玻璃,测试样品温度变化发现温升较缓,温降迅速,耐热性能优越。实验结果表明,将荧光玻璃用于LED白光照明封装,能实现流明效率和耐热性能的大幅提升,形成良好的白光输出。     

有机电致蓝光器件激发YAG∶Ce荧光粉光谱特性研究

模拟无机大功率白光LED由蓝光芯片激发荧光粉形成白光的发光方式,基于有机电致蓝光器件激发黄色的YAG∶Ce荧光粉来实现全色器件.采用真空蒸镀法,制备了ITO/2T-NATA(30 nm)/AND ∶ TB-Pe(50 Wt％,40 nm)/Alq3 (100 nm)/LiF(1 nm)/Al(100 nm)的蓝光器件,...     

LED激发有机材料MPPV的光谱分析

通过旋涂方法在玻璃片上涂敷一层有机材料MPPV,其中有机材料MPPV溶于有机溶剂四氢呋喃溶液中,MPPV:四氢呋喃的比例分别为25mg∶1mL,50mg∶1mL,100mg∶1mL,150mg∶1mL。然后分别使用蓝光、白光LED去照射有机薄膜层来研究其发光特性。结果表明:蓝光LED、白光LED均能激发有机材料MPPV使其在600～750nm区域产生红光光谱,且随着溶解质量分数的增加,光谱色坐标从(0.265 4,0.248 9)移向(0.395 4,0.288 0),发生红移。当MPPV:四氢呋喃的比例为100mg∶1mL时,拥有最好的显色指数86.1,实验中色温最低可达2 609K,这比使用蓝光LED激发黄色YAG荧光粉得到的白光LED色温更低。因此蓝光LED、白光LED通过激发有机材料MPPV可以显著提高LED的显色指数及发光性能。     

红色荧光粉MMoO4:Eu3+ (M=Ca,Sr,Ba)的水热合成及光谱性质

采用水热合成法制备了红色荧光粉MMoO4:Eu3+ (M=Ca,Sr,Ba),用XRD、SEM、荧光激发和发射光谱对其物相、形貌以及发光性能进行表征和研究.结果表明,在800℃时可得到MMoO4(M=Ca,Sr,Ba)物相结构,荧光粉粒径小且粒度分布均匀.分别以395 nm的近紫外光和465 nm的蓝光激发样品,MMoO4:Eu3+(M=Ca,Sr,Ba)荧光粉发红光,对应于Eu3+的4f-4f跃迁,其中以616nm发光最强.荧光粉在395nm和465nm的吸收分别与紫外光和蓝光LED芯片的发射相匹配.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.