Li3V2(PO4)3的溶胶-凝胶合成及其性能研究

以LiOH·H₂O(LiF、Li₂CO₃、LiCH₃COO·2H₂O)、NH₄VO₃、H₃PO₄和柠檬酸为原料,采用Sol-gel法合成锂离子电池正极材料Li₃V₂(PO₄)₃。优化了锂源、溶胶的pH值、预烧条件、煅烧温度等合成条件,并采用XRD、SEM、恒电流充放电及循环伏安试验等方法,研究了所合成的Li₃V₂(PO₄)₃的结构形貌和电化学性能。结果表明,以LiOH·H₂O为锂源,溶胶的pH值等于3,于氩气氢气(体积比9∶1)混合气中300 ℃预烧 4 h,并在氩气氢气(体积比9∶1)混合气中600 ℃煅烧8 h合成的Li₃V₂(PO₄)₃正极材料为标准的单斜结构,具有较高的放电比容量和较好的循环稳定性,0.1C和1C倍率下首次放电比容量分别为130 mAh·g^-1和129 mAh·g^-1;1C倍率下循环40次后,容量仍为127 mAh·g^-1,容量保持率为98.4%;随后又进行10C倍率放电,10次循环后容量为105 mAh·g^-1,容量保有率达98.1%。循环伏安测试表明,该正极材料具有较好的电化学可逆性。     

SiO44-对Li3Sc2(PO4)3快离子导体的阴离子替代效果研究

Li3Sc2(PO4)3因具有有利的离子传导通道、低的电子电导率和高的稳定性而成为全固态锂离子电池用固体电解质最具竞争力的材料之一,然而这一化合物只有在245℃以上的γ相才具有快离子传导特性。人们主要采用Zr4+、Ti4+等阳离子部分取代其中的Sc3+以改善材料的室温电导率,有关该化合物PO43-阴离子替代的报道还很少。本研究试图利用机械研磨技术,通过向Li3Sc2(PO4)3原料混合物中加入适量SiO2,以期能够实现对该化合物的部分阴离子替代。研究结果表明:所制备的Li3+xSc2(PO4)3-x(SiO4)x(x=0~0.6)系列化合物在x=0.15时电导率达到最大值,σ298=9.55×10-4 S.m-1,离子传导激活能达到最小值45.06 kJ.mol-1。29Si MAS-NMR测试结果证实所加入的SiO2主要以[SiO4]四面体形式存在替代Li3Sc2(PO4)3中部分[PO4]四面体。     

碳包覆Li3V2(PO4)3:溶胶-凝胶法合成及性能

利用V₂O₅、LiOH·H₂O、H₂O₂、NH₄H₂PO₄与柠檬酸为原料,通过溶胶-凝胶法合成了碳包覆的Li₃V₂(PO₄)₃复合正极材料。采用XPS、XRD、SEM、TEM、拉曼光谱和电化学方法对材料的性能进行了研究。还研究了其结构与焙烧温度、样品电导率和电化学性能的关系。研究表明复合材料具有空间群为P2₁/n的单斜结构,表面包覆粗糙多孔的碳层。在800 ℃下制备的碳包覆样品的电子导电率高达9.81×10^-5 S·cm^-1,约为高温固相氢气还原法制备的未包覆碳Li₃V₂(PO₄)₃的10000倍。测试结果表明碳包覆Li₃V₂(PO₄)₃的电化学性能远优于未包覆碳的样品。在3.0～4.3 V电压范围内,以0.1C和2C倍率充放电时,碳包覆的Li₃V₂(PO₄)₃具有高比容量(分别为128和109 mAh·g^-1)和优异的循环性能。     

Topotactic insertion of lithium in the layered structure Li4VO(PO4)2: The tunnel structure Li5VO(PO4)2

A new V(III) lithium phosphate Li₅VO(PO₄)₂ has been synthesized by electrochemical insertion of lithium into Li₄VO(PO₄)₂. This phase, which crystallizes in the space group I4/mcm, exhibits a tunnel structure closely related to the layered structure of Li₄VO(PO₄)₂ and to the tunnel structure of VO(H₂PO₄)₂. The topotactic reactions that take place during lithium exchange and intercalation, starting from VO(H₂PO₄)₂ and going to the final phase Li₅VO(PO₄)₂ are explained on the basis of the flexible coordinations of V⁴⁺ and V³⁺ species. The electrochemical and magnetic properties of this new phase are also presented and explained on the basis of the structure dimensionality.     

Li3V2(PO4)3的溶胶-凝胶法合成及其性能研究

以LiOH·H₂O、NH₄VO₃、H₃PO₄和柠檬酸等为原料采用溶胶-凝胶法合成了锂离子二次电池正极材料磷酸钒锂(Li₃V₂(PO₄)₃)。考察了煅烧温度和配位剂种类等条件对产物组成及电化学性能的影响。研究了优化条件下制得样品的循环伏安、充放电性能和循环性能。0.1 C条件下,样品首次放电比容量达129.81 mAh·g^-1，经过100次循环后容量几乎没有衰减，仍保持在128 mAh·g^-1。X射线衍射研究表明合成单一Li₃V₂(PO₄)₃晶体所需温度比固相法低；并考察了循环20次后材料充电到各个单相的晶体结构，通过X射线衍射和最小二乘法计算给出了其晶胞参数变化过程，证实了循环嵌Li过程中晶体结构能够得到重现。     

溶胶-凝胶法制备Li3V2(PO4)3及其性能研究

0引言具有类NASICON结构的Li3V2(PO4)3是继过渡金属氧化物LMO后的一种新型的锂离子二次电池正极材料。与目前市场上应用最为广泛的正极材料LiCoO2相比,Li3V2(PO4)3具有超常的稳定性,即使在脱出的Li 与过渡金属原子的物质的量之比大于1的时候仍然具有超乎寻常的稳定性,而通常情况下1mol LiCoO2在脱出0.5mol Li 就会变得不稳定。并且Co是一种战略物资,全球储量十分有限;Co也是一种有毒金属,对于环境污染较为严重。LiNiO2因其合成较为困难而使应用受限,尖晶石LiMn2O4虽然属于环境友好型化合物,但其理论比容量仅为148mAh·g-1,且…     

Properties of the perovskites, SrMn1−xFexO3−δ (x=1/3, 1/2, 2/3)

The SrMn_1−xFe_xO_3−δ (x=1/3, 1/2, 2/3) phases have been prepared and are shown by powder X-ray and neutron (for x=1/2) diffraction to adopt an ideal cubic perovskite structure with a disordered distribution of transition-metal cations over the six-coordinate B-site. Due to synthesis in air, the phases are oxygen deficient and formally contain both Fe³⁺ and Fe⁴⁺. Magnetic susceptibility data show an antiferromagnetic transition at 180 and 140 K for x=1/3 and 1/2, respectively and a spin-glass transition at 5, 25, 45 K for x=1/3, 1/2 and 2/3, respectively. The magnetic properties are explained in terms of super-exchange interactions between Mn⁴⁺, Fe^(4+δ)+ and Fe⁽³⁺⁾⁺. The XAS results for the Mn-sites in these compounds indicate small Mn-valence changes, however, the Mn-pre-edge spectra indicate increased localization of the Mn-e_g orbitals with Fe substitution. The Mössbauer results show the distinct two-site Fe⁽³⁺⁾+/Fe^(4+δ)+ disproportionation in the Mn- substituted materials with strong covalency effects at both sites. This disproportionation is a very concrete reflection of a localization of the Fe-d states due to the Mn-substitution.     

可见光响应的Co3(PO4)2/Ag3PO4纳米复合光催化剂的制备及表征

采用简单的化学偏聚法合成出Ag₃PO₄纳米颗粒、磷酸钴（Co₃（PO₄）₂,CoP）纳米片以及它们两者的纳米复合结构（CoP/Ag₃PO₄）,同时还比较了它们的可见光催化活性. 采用场发射扫描电镜（FESEM）、X 射线衍射（XRD）、紫外-可见（UV-Vis）吸收光谱以及光致发光谱等手段对其形貌、结构、光学以及可见光催化性能等进行表征. 结果表明,CoP/Ag₃PO₄复合纳米结构的可见光降解甲基橙（MO）的速率和循环稳定性均明显优于其它两种物质. 这表明CoP应该起着共催化剂的作用,它能够抑制光生电子与空穴之间的复合,并且提供大量高活性的光生空穴. 此外,我们还发现CoP/Ag₃PO₄降解另一种阳离子型染料——罗丹明B（RhB）的能力则远不如纯Ag₃PO₄,这可能是与光催化剂的表面性质发生改变有关,造成更低的RhB吸附能力. 本文提供了一种廉价制备高效可见光催化剂的新方法.     

低温固相反应合成Li3V2(PO4)3正极材料及其性能

利用V₂O₅·nH₂O湿凝胶，LiOH·H₂O，NH₄H₂PO₄和C等作原料，通过低温固相还原反应在550 ℃焙烧12 h制备出Li₃V₂(PO₄)₃正极材料。采用XRD，SEM和电化学测试对Li₃V₂(PO₄)₃样品性能进行研究。XRD研究表明本法所合成的Li₃V₂(PO₄)₃同传统的高温固相反应法所合成的Li₃V₂(PO₄)₃一样同属于单斜晶系结构。SEM测试表明所合成的样品平均粒径大小约为0.5 μm且粒径分布较窄。电化学测试表明以0.2 C的倍率放电时，样品的首次放电容量为130 mAh·g^-1，室温下循环30次后其比容量为124 mAh·g^-1。     

溶胶-喷雾干燥法制备纳米Li3V2(PO4)3/C及其电化学性能

本文以LiOH.H2O、NH4VO3、H3PO4和柠檬酸为原料,采用溶胶-喷雾干燥法制备Li3V2(PO4)3/C正极材料,对比了喷雾前驱体直接煅烧与机械活化后煅烧的样品的结构、形貌及其电化学性能。采用XRD、SEM、BET和振实密度测试等对样品的结构、形貌等进行了表征;采用恒流充放电、CV和EIS等手段考察了材料的电化学性能。结果表明,溶胶-喷雾干燥得到的样品为多孔球壳形,其壳体由厚度为100 nm左右的纳米片组成,经机械活化后煅烧保持保持了其纳米片结构,其结晶度与振实密度改善较明显,电化学性能较优异。0.1C放电比容量为123.6 mAh.g-1,10C和20C高倍率放电比容量还高达107.8和106.0 mAh.g-1。电化学阻抗结果表明,由该方法制备的样品具有较小的电荷转移阻抗。     

A TEM, XRD, and crystal chemical investigation of oxygen/vacancy ordering in (Ba1−xLax)2In2O5+x, 0x0.6

A careful TEM and XRD study of the (Ba_1−xLa_x)₂In₂O_5+x, 0x0.6, ‘defect-perovskite’-type solid solution has been carried out. A well-defined structural phase transition is shown to occur between x=0.1 and 0.2 from the orthorhombic brownmillerite structure type on the low x side to a multiple twinned, tetragonal 1×1×2 perovskite-related superstructure phase on the high x side at x=0.2. This phase transition correlates with an important phase transition previously observed in electrical conductivity versus temperature measurements. The existence of additional satellite reflections close to the regions of reciprocal space was found to be typical of all (Ba_1−xLa_x)₂In₂O_5+x specimens, although their intensity relative to the parent Bragg reflections systematically reduces as x increases. As x increases beyond 0.2, the -type satellite reflections initially become weaker and rather more diffuse for x=0.3 before splitting into pairs of rather weak and somewhat diffuse incommensurate satellite reflections for x=0.4 and beyond. An interpretation in terms of oxygen vacancy ordering and associated structural relaxation is given. Additional structured diffuse scattering is also observed and a tentative explanation in terms of Ba/La ordering and associated local strain distortions put forward.     

Synthesis and structural study of a new NASICON-type solid solution: Li1−xLax/3Zr2(PO4)3

A new complete solid solution of NASICON-type compounds between LiZr₂(PO₄)₃ and La_1/3Zr₂(PO₄)₃ was evidenced with the general formula Li_1−xLa_x/3Zr₂(PO₄)₃ (0?x?1). These phases were synthesized by a complex polymerizable method and structurally characterized from Rietveld treatment of their X-ray and neutron powder diffraction data. This solid solution results from the substitution mechanism Li⁺→1/3La³⁺+2/3□ leading to an increase of the vacancies number correlated to an increase of the La content. According to this substitution mechanism, the general formula can then be written Li_1−xLa_x/3□_2x/3Zr₂(PO₄)₃ (0?x?1) in order to underline the correlation between the La content and the vacancies rate. For all the compounds, the structure is clearly related to that of the NASICON family with three crystallographic domains evidenced. For 0?x?0.5, all the members adopt at high temperature the typical NASICON-type structure (s.g. R3¯c), while at lower temperature, their structure distorts to a triclinic form (s.g. C 1¯), as observed for LiZr₂(PO₄)₃ prepared above 1100 °C. Moreover, in this domain, the reversible transition is clearly soft and the transition temperature strongly depends of the x value. For 0.6?x?0.9, the compounds crystallize in a rhombohedral cell (s.g. R3¯), while for x=1, the phase La_1/3Zr₂(PO₄)₃ is obtained (s.g. P3¯, Z=6, a=8.7378(2) Å, c=23.2156(7) Å).This paper is devoted to the structure analysis of the series Li_1−xLa_x/3Zr₂(PO₄)₃ (0?x?1), from X-ray and neutron powder thermo diffraction and transmission electron microscopy (TEM) studies.     

Cr2(WO4)3和Cr2(MoO4)3的负热膨胀特性研究

用液相反应-前驱物烧结法制备了Cr₂(WO₄)₃和Cr₂(MoO₄)₃粉体。298～1 073 K的原位粉末X射线衍射数据表明Cr₂(WO₄)₃和Cr₂(MoO₄)₃的晶胞体积随温度的升高而增大, 本征线热膨胀系数分别为(1.274±0.003)×10^-6 K^-1和(1.612±0.003)×10^-6 K^-1。用热膨胀仪研究了Cr₂(WO₄)₃和Cr₂(MoO₄)₃在静态空气中298～1 073 K范围内热膨胀行为，即开始表现为正热膨胀，随后在相转变点达到最大值，最后表现为负热膨胀，其负热膨胀系数分别为(-7.033±0.014)×10^-6 K^-1和(-9.282±0.019)×10^-6 K^-1。     

Li3V2(PO4)3/C的P123辅助流变相法制备及电化学性能

以V₂O₅、NH₄H₂PO₄、LiOH、柠檬酸、三嵌段聚合物表面活性剂P123为原料, 用流变相(RPR)法制备了Li₃V₂(PO₄)₃/C正极材料. 用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)等方法表征, 结果表明: 材料为单一纯相的单斜晶体结构, 颗粒均匀并呈现珊瑚结构; 恒流充放电, 循环伏安(CV)及电化学交流阻抗(EIS)等电化学性能测试表明, 采用P123 辅助合成材料电化学性能明显优于未采用P123 辅助合成材料. 3.0-4.3 V放电区间, 0.1C充放电下P123 辅助合成Li₃V₂(PO₄)₃/C材料首次放电比容量为129.8 mAh·g^-1, 经过50 次循环后容量只衰减0.9%; 倍率性能及循环性能优异, 1C、10C、25C的首次放电比容量分别为128.2、121.3、109.1 mAh·g^-1, 50次循环后容量保持率分别为99.1%, 96.9%, 90.7%. 这归因于三嵌段聚合物P123 作为分散剂的同时也作为有机碳源在颗粒表面及间隙形成碳网络, 有利于材料导电率的改善, 降低了其电荷转移阻抗, 减小了电极充放电过程的极化现象.     

Thermoelectric properties of Cu-doped n-type (Bi2Te3)0.9–(Bi2−xCuxSe3)0.1(x=0–0.2) alloys

n-Type (Bi₂Te₃)_0.9–(Bi_2−xCu_xSe₃)_0.1 (x=0–0.2) alloys with Cu substitution for Bi were prepared by spark plasma-sintering technique and their structural and thermoelectric properties were evaluated. Rietveld analysis reveals that approximate 9.0% of Bi atomic sites are occupied by Cu atoms and less than 4.0 wt% second phase Cu_2.86Te₂ precipitated in the Cu-doped parent alloys. Measurements show that an introduction of a small amount of Cu (x0.1) can reduce the lattice thermal conductivity (κ_L), and improve the electrical conductivity and Seebeck coefficient. An optimal dimensionless figure of merit (ZT) value of 0.98 is obtained for x=0.1 at 417 K, which is obviously higher than those of Cu-free Bi₂Se_0.3Te_2.7 (ZT=0.66) and Ag-doped alloys (ZT=0.86) prepared by the same technologies.     

Solubility of (UO2)3(PO4)2?4H2O in H+-Na+-OH?-H2PO?4-HPO2?4-PO3?4-H2O and Its Comparison to the Analogous PuO2 +2 System

The objectives of this study were to address uncertainties in the solubility product of (UO₂)₃(PO₄)₂⋅4H₂O(c) and in the phosphate complexes of U(VI), and more importantly to develop needed thermodynamic data for the Pu(VI)-phosphate system in order to ascertain the extent to which U(VI) and Pu(VI) behave in an analogous fashion. Thus studies were conducted on (UO₂)₃(PO₄)₂⋅4H₂O(c) and (PuO₂)₃(PO₄)₂⋅4H₂O(am) solubilities for long-equilibration periods (up to 870 days) in a wide range of pH values (2.5 to 10.5) at fixed phosphate concentrations of 0.001 and 0.01 M, and in a range of phosphate concentrations (0.0001–1.0 M) at fixed pH values of about 3.5. A combination of techniques (XRD, DTA/TG, XAS, and thermodynamic analyses) was used to characterize the reaction products. The U(VI)-phosphate data for the most part agree closely with thermodynamic data presented in Guillaumont et al.,⁽¹⁾ although we cannot verify the existence of several U(VI) hydrolyses and phosphate species and we find the reported value for formation constant of UO₂PO⁻₄ is in error by more than two orders of magnitude. A comprehensive thermodynamic model for (PuO₂)₃(PO₄)₂⋅4H₂O(am) solubility in the H⁺-Na⁺-OH⁻-Cl⁻-H₂PO⁻₄-HPO²⁻₄-PO³⁻₄-H₂O system, previously unavailable, is presented and the data shows that the U(VI)-phosphate system is an excellent analog for the Pu(VI)-phosphate system.     

Synthesis and ac susceptibility of YCa2Cu3O7−δ

The bulk superconducting YCa₂Cu₃O_7−δ compounds are prepared at an ordinary pressure of oxygen by conventional solid-state reaction method. The formation of sample is tested by means of XRD and is studied for their ac susceptibility below room temperature up to 77.5 K. The samples are found single-phase orthorhombic structure and found superconducting at 83.5 K. It is shown that the analysis is consistent with published data on YBa₂Cu₃O_7−δ oxide superconductor.     

喷雾干燥法制备Li_(1.2)Mn_(0.4+x)Ni_xCr_(0.4-2x)O_2及其结构与电化学特征

利用喷雾干燥法合成了富锂三元正极材料Li1.2Mn0.4+xNixCr0.4-2xO2(x=0,0.05,0.10,0.15,0.20,以下简称为SD1~SD5),并利用XRD,XPS,ICP,TEM,SEM等手段对材料进行结构,元素价态,形貌及电化学性能等方面的表征。SD1~SD5系列样品都具有层状结构,其所含的Cr元素为Cr6+和Cr3+共存,而Ni元素价态为+2.5价,Mn元素为+4价。SD1~SD4样品中由于存在非晶态的Li2CrO4,导致样品表现出强烈的吸湿性。这个问题可通过水洗处理来解决,且水洗处理对于改善该系列材料的电化学性能有明显的效果。SD1~SD5系列样品中,SD1与SD4样品电化学性能较好,以20 mA.g-1的放电电流密度,在4.8~2.0 V电压区间内,首次放电比容量分别为247和220 mA.h.g-1,经过20次充放电循环后,容量保持率分别为73%和78%。高温条件下SD1和SD4样品的首次放电比容量分别增大为256和237 mA.h.g-1,经过20次充放电循环后容量保持率分别为83%和99%。将充放电电压扩展为5.0~2.0 V时,SD4样品首次放电比容量可以达到307 mA.h.g-1。     

Hydrothermal synthesis and luminescent properties of Sb-doped Sr3(PO4)2

Sb³⁺-doped Sr₃(PO₄)₂ crystals has been synthesized using phosphoric acid, strontium hydroxide and antimony powder as the raw materials through a hydrothermal reaction method. The crystallinity and the microstructure were investigated using X-ray diffraction and scanning electron microscopy. The photoluminescent property was investigated using luminescent spectrometer. Phase pure Sr₃(PO₄)₂ crystal was obtained and it has a shape of hexagonal rod. It showed the emission and excitation peaks at 396, 250, and 215 nm, respectively, indicating that the emission is attributed to ³P₁-¹S₀ transition and the excitation is attributed to ¹S₀-³P₁ and ¹S₀-¹P₁ transition. It was also observed that the intensity of photoluminescence is thermally stable up to 673 K.     

Ti掺杂对(LaMn1-xTixO3)0.67(NiMn2O4)0.33(0≤x≤0.7)陶瓷材料微结构及电性能影响

采用氧化物固相法制备(LaMn1-xTixO3)0.67(NiMn2O4)0.33系列NTC(Negative temperature coefficient)复合热敏电阻材料。利用TG/DSC、激光粒度分析、XRD、SEM、阻-温特性和老化性能测试等手段,确定了粉体煅烧温度,表征了粉体的颗粒尺寸、陶瓷体的物相、形貌及其电学特性、稳定性等与Ti掺杂量的关系。结果表明:在1 200~1 300℃烧结温度范围内,(LaMn1-xTixO3)0.67(NiMn2O4)0.33复合体系的电阻率ρ25℃随Ti含量的增加而显著增加;电阻率ρ25℃和B值变化范围分别为4.4~53 179Ω.cm、1 357~3 998 K。125℃下老化1 000 h阻值变化率ΔR/R0均小于0.51%。该复合体系电阻率、B值调整范围较大,稳定性好,是一种具有实际应用价值的NTC热敏电阻材料。