2-(2-喹啉偶氮)-1,5-苯二酚分光光度法测定烟草样品中的钙

在 p H为 8.0的柠檬酸钠 -氢氧化钠缓冲介质中 ,Triton X- 10 0存在下 ,2 - (2喹啉偶氮 ) - 1,5苯二酚(QADHB)与钙反应生成 1∶ 1稳定配合物 ,λmax=5 5 5 nm,ε=4 .18× 10 4L· mol-1· cm-1。钙含量在 0 .1—2 5μg/ 2 5 m L的范围内符合比耳定律 ,方法用于烟草中钙含量的测定 ,结果令人满意。     

对乙酰基偶氮氯膦光度法测定烟草中钙的方法研究

研究了对乙酰基偶氮氯膦 ( ACCPP)与钙的显色反应 ,在 p H=8.5的氯化铵 -氨水缓冲介质中 ,乳化剂 - OP存在下 ,ACCPP与钙反应生成 1∶ 1稳定络合物 ,λmax=680 nm,ε=4 .0 1× 10 4 L· mol-1· cm-1。钙含量在 0— 2 0μg/2 5m L范围内符合比耳定律 ,方法用于烟草样品中钙含量的测定 ,结果令人满意。     

槲皮素-铁配合物的光度法研究

在 p H=4 .0 5的 HAc- NH4 Ac缓冲体系中 ,槲皮素 ( Qu)与 Fe3+配位 ,该配合物在 4 30 nm处有最大吸收。 Fe3+的浓度在 2 .0× 10 -5— 1.2× 10 -4 mol· L-1之间与吸光度成线性关系 ,最低检出限为 2 .0× 10 -5mol· L-1。测得配合物的组成为 Fe3+∶ Qu=1∶ 2 ,稳定常数 K稳 =1.0× 10 8。     

4-(2-羟基-4-硝基苯偶氮)-1-苯基-3-甲基吡唑啉酮光度法测定烟草中镁

研究了 4 - (2 -羟基 - 4-硝基苯偶氮 ) - 1-苯基 - 3-甲基吡唑啉酮 (HNAPMP)与镁的显色反应 ,在 p H=10的硼砂 -氢氧化钠缓冲介质中 ,HNAPMP与镁反应生成 2∶ 1稳定络合物 ,λmax=5 2 2 nm,ε=3.5 8× 10 4L·mol-1· cm-1。镁含量在 0— 2 0 μg/2 5 m L范围内符合比耳定律 ,方法用于烟草样品中镁含量的测定 ,结果令人满意     

溴化5-[4-(3-吡啶丙氧基苯基)]-10，15，20-三苯基卟啉对铜离子显色反应的研究

本文研究了溴化 5- [4 - (3-吡啶丙氧基苯基 ) ]- 10 ,15,2 0 -三苯基卟啉 ,在 p H=4 .0时与 Cu2 + 的显色反应条件 ,其络合物最大吸收波长为 4 13nm。在相同条件下 ,试剂最大吸收波长为 4 4 4nm,对比度大约30 nm。试剂与铜络合比为 1∶ 1,表观摩尔吸光系数为 2 .9× 10 5L· mol-1·cm-1,铜含量在 0— 6 0 μg/ L范围内符合比耳定律 ,可用于痕量铜的测定。     

新显色剂四(4-甲氧基-4-磺酸基苯基)卟啉与Fe~(3+)的高灵敏反应的研究与应用

本文提出以四 (4 -甲氧基 - 4 -磺酸基苯基 )卟啉 (p- OCH3TPPS4 )为显色剂 ,在 p H=3.5— 5 .5的条件下测定痕量铁的新体系 ,络合物最大吸收波长为 4 4 6nm,表观摩尔吸收系数ε=2 .0× 10 4 L· mol-1· cm-1,Fe3+ 在 0— 10 μg/ 2 5 m L 范围内符合比耳定律 ,应用本法测定花生仁皮中铁 ,回收率可达 95 .0 %—10 8.4 %     

溴化5-［4-(2-吡啶-乙氧基)苯基］-10，15，20-三苯基卟啉对铜离子的显色反应研究

本文研究了溴化 5- [4 - ( 2 -吡啶 -乙氧基 )苯基 ]- 10 ,15,2 0 -三苯基卟啉与 Cu2 +的显色反应条件 ,在 p H=4 .0时 ,其络合物最大吸收波长为 4 13nm,试剂最大吸收波长为 4 4 3.5nm。对比度大约为 30 nm。试剂与铜络合比为 1∶ 1,其络合物表观摩尔吸光系数为 3.4× 10 5L·mol-1· cm-1,铜含量在 0— 0 .5μg/ 10 m L范围内符合比耳定律 ,本研究可用于痕量铜的测定     

黄酮化合物的偶氮显色反应及其应用研究

在pH 10 4的NH4Cl NH3 ·H2 O缓冲溶液中 ,对磺基氯化重氮苯可与芦丁 ,桑色素 ,染料木甙 ,槲皮素 ,橙皮甙 ,黄岑甙和大豆甙等 7种黄酮化合物发生偶氮显色反应 ,反应产物的最大吸收波长 ,除黄岑甙为 380nm外 ,其余均在 4 30nm ,显色反应的灵敏度依上述顺序逐渐减弱。其中芦丁的摩尔吸收光系数最大 ,为 3 2 8× 10 4L·mol-1·cm-1,大豆甙摩尔吸光系数最小 ,为 8 30× 10 2 L·mol-1·cm-1。提出的分光光度分析方法 ,用于槐米和豆粕中黄酮化合物的测定 ,RSD为 0 2 5 %～ 4 4 8% ,回收率在 99 3%～ 10 5 0 %之间     

N，N‘－双（2－水杨醛缩氨基苯基）1，3－丙二酸二酰胺与锌的显色反应研究

本文研究了新试剂 N,N′-双 (2 -水杨醛缩氨基苯基 ) 1,3-丙二酸二酰胺 (H2 Sapma)与锌的灵敏显色反应。在 p H为 7.0— 7.8的硼砂 - HCl缓冲溶液中。配合物的组成比是 Zn∶H2 Sapma=1∶ 1,配合物的最大吸收波长在 4 10 nm处 ,表观摩尔吸光系数为 1.6 9× 10 4L· mol-1· cm-1,锌量在 0— 4 0μg/2 5 m L范围内符合比耳定律。用于测定人发及强化营养盐中微量锌 ,结果令人满意。     

1-(2,6-二溴-4-硝基苯)-3-(4-硝基苯)-三氮烯与锌的显色反应研究

研究了 1- (2 ,6-二溴 - 4 -硝基苯 ) - 3- (4 -硝基苯 ) -三氮烯 (DBNPNPT)与锌的显色反应。在表面活性剂Triton X- 10 0的存在下 ,p H=9.0— 11.0的 Na2 B4 O7- Na OH介质中 ,DBNPNPT与锌 ( )可生成橙黄色络合物。建立以 5 35 nm为参比波长 ,4 4 0 nm为测定波长的双峰双波长测定法 ,该络合物的表观摩尔吸光系数为 1.34× 10 5L· mol-1· cm-1。对葡萄糖酸锌中的锌直接测定 ,结果令人满意     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.