一种新的毛细管电泳动态涂层筛分介质的研究

在线性聚N-异丙基丙烯酰胺（Poly-N-isopropylacrylamide,PNIPAM）的TBE溶液中添加半乳糖醇组成一种新的分离脱氧核糖核酸（DNA）筛分介质.该筛分介质具有动态涂层和低粘度的特点,对ΦX174/HaeⅢ、pBR322/HaeⅢDNA片段获得了较好的分离效果.文中还对半乳糖醇提高筛分能力的作用机理进行了探讨.     

基于温敏性N,N-二甲基丙烯酰胺/N-异丙基丙烯酰胺无规共聚物的毛细管无胶电泳筛分介质北大核心CSCD

本文合成了N,N-二甲基丙烯酰胺/N-异丙基丙烯酰胺无规共聚物(P(DMA-co-NIPAM))和聚N,N-二甲基丙烯酰胺(PDMA),并将二者共混制备毛细管无胶电泳筛分介质,旨在降低筛分介质粘度的同时增强其对DNA的分离性能。核磁共振氢谱(1H NMR)和傅里叶变换红外光谱(FT-IR)证明了2种聚合物的成功合成。表征了P(DMA-co-NIPAM)/PDMA共混物溶液的流体力学直径(Dh)、低剪切粘度和吸光度,结果表明,P(DMAco-NIPAM)聚合物具有温敏性,低临界溶解温度(LCST)为60~80℃。DNA筛分结果显示,PDMA中添加了10%P(DMA-co-NIPAM)的复合筛分介质性能最好,相比PDMA粘度降低19%以上,对大DNA片段的分辨率和理论塔板数均明显提高,分离时间缩短4%,显示了优良的分离性能。     

聚N-异丙基丙烯酰胺硅胶键合固定相的应用

采用N-异丙基丙烯酰胺制备了聚N-异丙基丙烯酰胺硅胶键合固定相。试验将聚N-异丙基丙烯酰胺硅胶键合固定相应用于碱性物质和酯类物质的分离,各组分实现了基线分离,且色谱峰形对称;并利用聚N-异丙基丙烯酰胺硅胶键合固定相,在甲醇-水(30+70)混合液为流动相,28~32℃时发生了相转变,由亲水性构象转变为疏水性构象的温敏特性,可将其用于两种极性差异较大的极性化合物分析中。     

聚N-异丙基丙烯酰胺/纳米SiO2复合水凝胶的合成及溶胀性能

通过纳米SiO2的表面功能化,在其表面引入乙烯基功能基团,在H2O／THF的混合溶剂中,超声分散后,交联剂N,N′-亚甲基双丙烯酰胺存在时,于25℃下使其与N-异丙基丙烯酰胺共聚,制得聚N-异丙基丙烯酰胺,纳米SiO2复合水凝胶,并用FT-IR和SEM对产物进行了表征,研究了凝胶的溶胀动力学,消溶胀动力学和温度敏感性,实验结果表明,纳米SiO2的引入,改善了聚N-异丙基丙烯酰胺水凝胶在低温时的溶胀性能和在高温时对水的释放性能,并讨论了引起这些性能改变的原因。     

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶的合成及表征

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶的合成及表征;N-异丙基丙烯酰胺;水凝胶;温敏性;快速响应     

浊度法表征温敏性微凝胶体积的相转变行为

以N-异丙基丙烯酰胺(NIPAM)、甲基丙烯酸(MAA)为单体,N,N-亚甲基双丙烯酰胺(MBA)为交联剂,制备了温敏性聚(N-异丙基丙烯酰胺)(PNIPAM)和具有温度、pH敏感性的聚(N-异丙基丙烯酰胺-co-甲基丙烯酸)(PNIPAM-MAA)微凝胶。通过测定不同温度和pH条件下微凝胶浊度变化,表征微凝胶的温度及pH敏感性,描述了NaCl浓度和pH对微凝胶体积相转变温度的影响。同时,测定了微凝胶的临界聚沉浓度及临界絮凝温度,表征了微凝胶的稳定性,讨论了影响微凝胶的稳定性因素。     

N-异丙基丙烯酰胺在超细硅胶表面接枝聚合及其在HPLC上的应用

通过硅烷偶联剂(γ-甲基丙烯酰氧基丙基三甲氧工硅烷)的作用,将N-异丙基丙烯酰胺在超细硅胶表面接枝聚合,制备了以聚N-异丙基丙烯酰胺为壳,硅胶粒子为核的具有温度敏感性复合粒子.研究了反应条件对接枝率的影响,对复合粒子的结构进行了表征.将制备的复合粒子用作高效液相色谱固定相,通过控制柱温对蔡的3种衍生物进行分离,表现了良好的分离性能.这种温控分离主要是由于硅胶表面的PNIPAM在经历相变温度时的极性变化所致.     

棉纤维的N-异丙基丙烯酰胺接枝共聚及产物的温敏性研究

以硝酸铈铵(CAN)、过硫酸钾(KPS)及H2O2/H2A(双氧水/抗坏血酸)为引发体系,采用溶液自由基接枝法制备了具有温敏性的棉纤维N-异丙基丙烯酰胺接枝共聚物(cotton-g-PNIPAAm);在上述3种引发剂作用下的接枝反应可以达到的接枝率(G)排序为G(H2O2/H2A)>G(KPS)>G(CAN);研究了其他因素如引发剂浓度、反应时间、反应温度和单体浓度等对接枝率的影响,得出了优化的接枝反应条件;接枝样品的FTIR分析图谱和SEM观察均表明样品表面已接枝了聚N-异丙基丙烯酰胺;DSC分析显示,棉纤维N-异丙基丙烯酰胺接枝共聚物的低临界溶解温度(LCST)与纯的聚N-异丙基丙烯酰胺凝胶(LCST=32.48℃)相似,约为32~33℃;接枝率的变化对试样LCST的影响很小,但其可逆焓变(ΔH)会随接枝率的提高而增加;采用滴水试验法(AATCC 79)和毛效试验法(FZ/T 01071)检测棉纤维的N-异丙基丙烯酰胺接枝共聚物在不同温度时的吸水性变化,显示试样具有温敏特性,其中接枝率介于25%~45%的试样温敏性较高,过低或过高的接枝率均不利于获得高的温敏性;棉纤维的N-异丙基丙烯酰胺接枝共聚物试样的可逆焓变(ΔH)随试样膨胀/收缩时间变化的研究和分析结果表明,棉纤维的N-异丙基丙烯酰胺接枝共聚物对温度变化的响应比纯聚N-异丙基丙烯酰胺凝胶快.     

利用聚(N-异丙基丙烯酰胺-co-丙烯酸)银纳米团簇构建宽pH响应范围的激发比率型荧光探针EI北大核心CSCD

以N-异丙基丙烯酰胺(NIPAM)和丙烯酸(AA)为pH敏感单体,合成聚(N-异丙基丙烯酰胺-co-丙烯酸),并以此作为模板制备了pH敏感的聚(N-异丙基丙烯酰胺-co-丙烯酸)银纳米团簇。结合了时间分辨荧光、透射电镜(TEM)、红外光谱(FT-IR)方法,对团簇的光学性能进行了研究。团簇的荧光对不同的pH具有灵敏的响应。团簇的荧光强度与pH在4.95~11.02的范围内呈线性关系,高pH(11.02)与低pH(4.95)相比,荧光强度降低约62.4%。同时,305 nm与453 nm处荧光激发强度的比值(I;/I;)与pH在5.94~11.02的宽范围内成线性关系,利用该荧光比率可以对pH进行定量检测。     

多孔聚N-异丙基丙烯酰胺水凝胶的制备与缓释性能

以N-异丙基丙烯酰胺(NIPA)、N,N-亚甲基双丙烯酰胺(MBA)和聚乙二醇(PEG)为原料,以60Co-γ射线为放射源制备了快速响应聚N-异丙基丙烯酰胺(PNIPA)多孔水凝胶。用红外光谱分析了水凝胶的结构,并测定了水凝胶的溶胀动力学、退溶胀动力学和平衡溶胀率。结果表明,PEG分子仅在聚合交联过程中充当成孔剂,不参与反应,反应后可被除去;水凝胶具有明显的温度敏感性,成孔剂的添加提高了水凝胶的溶胀性能和LCST。选用阿司匹林为模型药物,对水凝胶的药物缓释性能进行了初步研究。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。