首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
FAAS法对三种制备样品方法的研究   总被引:8,自引:0,他引:8  
张兆祥  阎军 《光谱实验室》1998,15(3):100-103
在FAAS法分析中,样品预处理始终占有极为重要的位置。本文比较了三种样品消化方式,即传统酸消化法,灰化法及微波消化法。传统的消化方式过程长、速度慢、效率低、而且被测元素易受到损失及易污染等不足,而微波是一种非常快捷、省时、省试剂和无污染的消化方式。通过对校准物质贻贝中的铜、锌、铁的测定结果证明微波消化方式比传统的消化方式优点多。  相似文献   

2.
能量色散X射线荧光分析中改进型基本参数法研究   总被引:2,自引:0,他引:2  
能量色散X射线荧光分析方法是目前常用的一种多元素分析方法,但该方法检出限和分析精度,受到分析基体的影响。基本参数法是目前一种常用的分析方法,但在使用过程必须获取净峰面积和基体所有成分,而在实际使用时,尤其在分析低含量样品时,净峰面积计算、基体中“暗物质”影响了测量精度,制约了基本参数法的应用。针对基本参数法的不足,将谱线解析方法与基本参数法融合,将重叠峰剥离过程嵌入基本参数法迭代过程中。在含量计算过程中,采用分析样品特征X射线分支比的理论系数,对重叠峰进行剥离,解决能量色散X射线荧光测量中净峰面积计算和定量分析问题;在计算过程中,对“暗物质”进行均一化处理。通过对标准物质测量分析,结果表明对于Ni,Cu,Zn三个元素改进型基本参数法(改进型FP)测量结果准确度高于影响系数法。  相似文献   

3.
徐贤胜  郭鹏  黄思训  项杰 《物理学报》2011,60(9):99202-099202
本文详细介绍了滑动频谱方法,并通过模拟仿真和实测资料处理与后传播方法进行比较. 通过对模拟仿真信号反演发现:后传播方法和滑动频谱方法均能削弱大气多路径的影响,后传播方法在一定程度上优于滑动频谱方法;在模拟信号的相位中加入高斯噪声对后传播方法影响不大,但对滑动频谱方法影响较大,尤其在边界层以下. 分别用后传播方法和滑动频谱方法对2007年第71天至73天共约4500个COSMIC掩星数据进行处理. 将折射率反演结果与ECMWF分析场资料进行统计比较,结果显示:滑动频谱方法反演的掩星廓线深度大于后传播方法;后 关键词: GPS/LEO掩星 多相位屏模型 后传播方法 滑动频谱方法  相似文献   

4.
 利用网络分析仪,根据需要在设定的频率范围进行扫频测量,网络分析仪的端口1输出的微波信号经过微波传输转换器进入与待测非标准元件匹配连接的连接段(如波导);网络分析仪的端口2连接定向耦合器,用于监测传输段内的反射微波信号。首先,在非标准接口端面连接短路面,通过网络分析仪测量反射信号在设定频点的相对幅度值;然后去掉短路面,在非标准接口端面连接待测元件,再次测量反射信号在特定频点的相对幅度值;最后根据本文推导的公式得出驻波系数。该方法的测量误差与定向耦合器的方向性(方向性系数越大越好)和待测元件驻波系数有关。将该方法运用在非标准接口匹配负载驻波系数的测量中,定向耦合器方向性系数取为40 dB,测得其驻波系数小于1.2,误差小于20%。该方法简便可行,可以用于测量常用的非标准接口元件尤其是非标准低驻波系数元件的驻波系数。  相似文献   

5.
In this paper, an improved interpolating moving least-square (IIMLS) method is presented. The shape function of the IIMLS method satisfies the property of the Kronecker δ function. The weight function used in the IIMLS method is nonsingular. Then the IIMLS method can overcome the difficulties caused by the singularity of the weight function in the IMLS method. The number of unknown coefficients in the trial function of the IIMLS method is less than that of the moving least-square (MLS) approximation. Then by combining the IIMLS method with the Galerkin weak form of the potential problem, the improved interpolating element-free Galerkin (IIEFG) method for two-dimensional potential problems is presented. Compared with the conventional element-free Galerkin (EFG) method, the IIEFG method can directly use the essential boundary conditions. Then the IIEFG method has higher accuracy. For demonstration, three numerical examples are solved using the IIEFG method.  相似文献   

6.
A new method for the combinatorial optimization of quasi-one-dimensional systems is presented. This method is in close analogy with the well-known transfer-matrix method. The method allows for the calculation of the lowest energy levels of the system. However, when finding the ground and some low-lying states of large complex systems, this method is more economical when compared to the standard transfer-matrix method. The method presented here is based on max-plus algebra, which has maximization and addition as its basic arithmetic operations. For the explanation of this method we use cyclic water clusters as simple examples. The efficiency of the max-plus-algebraic method is demonstrated in the course of global combinatorial optimization of hydrogen bond arrangements in large polyhedral water clusters with fixed positions of the oxygen atoms. The energy of the clusters is estimated using approximate discrete models for the intermolecular interactions.  相似文献   

7.
石墨炉原子吸收法测定全血中的铜和锌   总被引:5,自引:0,他引:5  
张源  罗文鸿  陈玲  李慧 《光谱实验室》2000,17(2):204-206
研究了石墨炉原子吸收法测定全血中铜和锌的方法。提出了用0.1%Triton X-100溶液作稀释剂,按1:50体积比稀释血样,采用校准曲线法就可测定全血中的铜和锌,方法简单,快速,并与基体匹配的校准曲线比较,结果令人满意。  相似文献   

8.
表面辐射测温方法的设计原理   总被引:3,自引:0,他引:3  
讨论了表面辐射测温方法的设计中所包含的几个基本问题:辐射的光谱和方向复杂性问题、光学设计问题以及电路设计问题,给出了具有普适意义的辐射测温基本分析式。比较了绝对辐射测温方法和相对辐射测温方法,指出前者须做标定,并且不宜进行温度场测量;后者无须标定,适合于温度场测量。  相似文献   

9.
通过快速傅里叶变换(FFT)法和复化辛普森法对衍射的数值进行计算,可以看出快速傅里叶变换法是一种积分变换法,而复化辛普森法则是迭代相加的方法.通过计算得出了FFT法的计算速度高于复化辛普森法,计算精度则远低于复化辛普森法;复化辛普森法适合近距离菲涅尔衍射和近场衍射,而FFT法不适合.  相似文献   

10.
 在传统谐振法基础上发展了一种计算慢性结构(SWS)冷腔参数的脉冲响应法,它的主要思想是利用有丰富谐波成分的窄脉冲作为激励源来代替实验系统中的扫频源,从而使得获取RBWO的色散曲线速度大大加快。这种方法使得脉冲响应法成为计算SWS冷腔参数的一种快速数值算法,更加适合于数值计算,并在研究HL-RBWO时得到有效的应用。  相似文献   

11.
Boundary element-free method for elastodynamics   总被引:3,自引:0,他引:3  
1 Introduction In recent years, more and more attention has been paid to researches on the meshless (or meshfree) method, which makes it a hot direction of computational mechanics[1,2]. The meshless method is the approximation based on nodes, then the large deformation and crack growth problems can be simulated with the method without the re-meshing technique. And the meshless method has some advantages over the traditional computa- tional methods, such as finite element method (FEM) and boun…  相似文献   

12.
阐述了含吸收散射性介质三维空腔内辐射传递方程的离散坐标解法。讨论了入射散射项积分格式的选取,以及假散射和射线效应对解精度的影响。对三维矩形炉膛内辐射传递过程进行了数值模拟,并与区域法和离散传递法进行比较。比较结果表明离散坐标法具有较好的精度,是目前燃烧室内辐射传热过程数值模拟的一种较好的方法。  相似文献   

13.
The moving least-square approximation is discussed first. Sometimes the method can form an ill-conditioned equation system, and thus the solution cannot be obtained correctly. A Hilbert space is presented on which an orthogonal function system mixed a weight function is defined. Next the improved moving least-square approximation is discussed in detail. The improved method has higher computational efficiency and precision than the old method, and cannot form an ill-conditioned equation system. A boundary element-free method (BEFM) for elastodynamics problems is presented by combining the boundary integral equation method for elastodynamics and the improved moving least-square approximation. The boundary element-free method is a meshless method of boundary integral equation and is a direct numerical method compared with others, in which the basic unknowns are the real solutions of the nodal variables and the boundary conditions can be applied easily. The boundary element-free method has a higher computational efficiency and precision. In addition, the numerical procedure of the boundary element-free method for elastodynamics problems is presented in this paper. Finally, some numerical examples are given.  相似文献   

14.
近红外光谱分析技术可用于对样本的快速无损检测,在人们的生产和生活中发挥着越来越重要的作用。支持向量机是建立定性分析模型的常用方法,可通过寻找最优分类超平面将两类样本分开。在小样本情况下,支持向量机方法有其独特的优势。主成分分析是常用的数据降维方法,可将数据降维之后作为支持向量机方法的输入变量,简化模型并提高模型识别的准确性。因此,基于主成分分析的支持向量机(简称PCA-SVM)适合用于建立近红外光谱定性分析模型。多模型方法是人们使用较少的建模方法,用该方法建立的模型一般具有较好的稳定性。将多模型方法与PCA-SVM方法成功结合形成了新方法。以棉锦混合、棉涤混合纺织品为例,用新方法建立了这两类纺织品样本的近红外光谱定性分析模型。建模时将光谱数据按照波长分为4组,用每组光谱数据建立一个子模型,将子模型的输出值进行加权平均便得到最终的预测结果。这样可以更充分地使用光谱数据中所包含的信息。为了便于对比不同的方法,仍使用上述校正集和验证集,又用PCA-SVM方法建立了这两类纺织品样本的近红外光谱定性分析模型。对预测结果做交叉验证,用新方法所建模型判别的正确率的平均值为85.49%,正确率的标准差为0.066 7, 用PCA-SVM方法所建模型判别的正确率的平均值为83.34%,正确率的标准差为0.109 6。研究结果表明用新方法所建模型的分类效果好于用PCA-SVM方法所建模型的分类效果;用新方法建立的模型的稳定性明显高于用PCA-SVM方法建立的模型的稳定性。用PCA-SVM方法所建模型的预测效果受校正集构成情况的影响较大,而用新方法所建模型的预测效果则相对稳定。对废旧纺织品进行分类回收可大量节约纺织原材料,但采用人工分拣方式效率低且成本高。采用近红外光谱分析方法对纺织品进行分类,为废旧纺织品的大规模精细分拣和分级奠定了一定的基础。该新方法有望用于某些其他类型样本的分类。  相似文献   

15.
三正辛胺棉富集分离原子吸收光谱法测定金   总被引:5,自引:0,他引:5  
论述了三正辛胺棉的制备及吸附金的条件和解脱方法。采用火焰原子吸收法进行测定。方法的测定范围为0.2-40g/t,相对标准偏差为2.3%,将该法用于制定黄铜矿中的金,其结果与传统的泡沫塑料富集-硫脲解脱原子吸收法测定结果一致,而本法分离效果好,测定速度快,操作简便。  相似文献   

16.
王聚丰  孙凤欣  程玉民 《中国物理 B》2012,21(9):90204-090204
In this paper, an improved interpolating moving least-square (IIMLS) method is presented. The shape function of the IIMLS method satisfies the property of Kronecker δ function. The weight function used in the IIMLS method is nonsingular. Then the IIMLS method can overcome the difficulties caused by the singularity of the weight function in the IMLS method. And the number of unknown coefficients in the trial function of the IIMLS method is less than that of the moving least-square (MLS) approximation. Then by combining the IIMLS method with the Galerkin weak form of the potential problem, the improved interpolating element-free Galerkin (IIEFG) method for two-dimensional potential problems is presented. Compared with the conventional element-free Galerkin (EFG) method, the IIEFG method can directly use the essential boundary conditions. Then the IIEFG method has a higher accuracy. For demonstration, three numerical examples are solved using the IIEFG method.  相似文献   

17.
刘观福  余聪 《大学物理》2021,40(3):79-85
求解定态薛定谔方程常常会涉及到常微分方程的本征值问题.目前解常微分方程本征值用的比较多的方法是以龙格-库塔方法为基础的打靶方法.打靶方法常用,但是计算时间长.当边界条件比较复杂或比较敏感的时候,用松弛法会有更好的效果.本文用松弛法解薛定谔方程,并和理论解进行比较.发现松弛法得到的数值解和理论解符合度很高,而且使用松弛法...  相似文献   

18.
本文对ICP-AES法测定氨甲环酸中痕量Pt和Ba的方法进行了研究,着重对氨甲环酸试样的不同分解方法进行了比较,用酸直接分解试样,方法简便,快速,试剂空白低,方法的回收率大于96.2%,相对标准偏差小于5%,准确度及精密度均符合要求,可用于氨甲环酸的生产控制和成品的检验分析。  相似文献   

19.
卢玉华  詹杰民 《物理学报》2006,55(9):4774-4782
研究了温盐双扩散系统的多组分格子Boltzmann方法.通过对二维方腔的温盐双扩散系统的数值模拟,检验了方法的可行性及有效性,所得到的结果与差分法结果符合良好,继而将此方法推广到三维,建立了三维温盐双扩散系统的格子Boltzmann方法,对三维方腔双扩散问题进行了模拟和分析,并与差分法模拟的结果进行了比较,结果令人满意.最后,分析了格子Boltzmann方法在模拟双扩散对流问题时存在的局限性. 关键词: 格子Boltzmann方法 温盐双扩散 Boussinesq近似 数值模拟  相似文献   

20.
休伦法 (Schlierenmethod)在观察物质流的折射率梯度方面的应用已有相当长的历史。对该方法进行改进 ,将其引入晶体生长的监控领域。介绍了该方法的原理及测量公式 ,并进行了实验观察 ,取得了比较理想的定性结果。结果表明 ,用这一方法可以很方便地观测透明物质或溶液中的折射率梯度或浓度的分布情况 ,特别是在晶体生长检测领域中有着广泛的应用前景。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号