Chelation ion-exchange properties of salicylic acid-urea-formaldehyde copolymers

Chelation ion-exchange properties of copolymers prepared from salicylic acid, urea and formaldehyde by condensation in presence of acid catalyst were studied for Cu²⁺, Fe³⁺, UO²⁺, Mn²⁺,Zn²⁺ and Co²⁺ ions. A batch equilibration method was adopted to study the selectivity of metal ion uptake. This method involved the measurement of distribution of a given metal between the copolymer sample and a solution containing the metal ions. The study was carried out over a wide pH range and in media of various ionic strengths. The copolymer showed a higher selectivity for UO₂ ²⁺, Cu²⁺ and Fe³⁺ ions than Mn²⁺, Co²⁺ and Zn²⁺ ions.     

Selective detection of phosphaphenanthrenecontaining luminophors with aggregation-induced emission enhancement to transition metal ions

Transition metal ions (Pb²⁺, Zn²⁺, Cd²⁺, Co²⁺, Mn²⁺, Cu²⁺, Ni²⁺, Hg²⁺, Ag⁺, Fe³⁺) in water are used to quench emission of 2-(6-oxido-6H-dibenz 〈c,e〉 〈1,2〉 oxaphosphorin-6-yl)-1,4-phenylene-bis(p-pentyloxylbenzoate)s (MD5) with aggregation-induced emission enhancement (AIEE) in water-acetonitrile (AN) mixture (80:20 by volume). Among all metal ions, Fe³⁺ exhibits the highest quenching efficiency on AIEE of MD5 even when the concentration of Fe³⁺ is lower than 1×10⁻⁶ mol/L. The quenching efficiency of Hg²⁺ is lower than that of Fe³⁺ at the same concentration, though MD5 is used to detect Hg²⁺ efficiently, too. To other metal ions, low quenching efficiency has few relations with a wider concentration range. The UV absorbance spectra show only red shift of absorbance wavelength in the presence of Hg²⁺ and Fe³⁺, which indicates a salt-induced Jaggregation. SEM photos reveal larger aggregation and morphological change of nanoparticles of MD5 in water containing Hg²⁺ and Fe³⁺, which reduce the surface area of MD5 emission for further aggregation. The selective quenching effect of transition metal ions to emission of MD5 has a potential application in chemical sensors of some metal ions.     

苯乙烯三嗪衍生物的合成及在重金属离子识别中的应用

合成了2,4-二(2-噻吩乙烯基)-6-(4'-N,N-二甲氨基苯乙烯基)-1,3,5-均三嗪(2)并鉴定了其结构。在乙腈-水混合介质中,化合物2在355和416nm处呈现双吸收峰,加入Cu²⁺,Hg²⁺ 和Fe³⁺ 后,均在520nm附近形成新的吸收峰。化合物2与Cu²⁺、Hg²⁺ 和Fe³⁺ 均形成1:1型配合物,其结合常数分别为1.9×10⁵L·mol^-1,6.6×10³L·mol^-1,2.7×10³L·mol^-1。对照化合物4与金属离子的光谱响应与化合物2相似,仅吸收峰的位置不同。因此,可认为化合物2和4中三嗪环中的N和噻吩环中的S与Cu²⁺、Hg²⁺ 和Fe³⁺ 共同配位形成了稳定的金属配合物。     

Novel repaglinide complexes with manganese(II), iron(III), copper(II) and zinc(II): Spectroscopic,DFT characterization and electrochemical behaviour

Novel transition metal complexes with the repaglinide ligand [2-ethoxy-4-[N-[1-(2piperidinophenyl)-3-methyl-1-1butyl] aminocarbonylmethyl]benzoic acid] (HL) are prepared from chloride salts of manganese(II), iron(III), copper(II), and zinc(II) ions in water-alcoholic media. The mononuclear and non-electrolyte [M(L)₂(H₂O)₂]?nH₂O (M = Mn²⁺, n = 2, M = Cu²⁺, n = 5 and M = Zn²⁺, n = 1) and [M(L)₂(H₂O)(OH)]?H₂O (M = Fe³⁺) complexes are obtained with the metal:ligand ratio of 1:2 and the L-deprotonated form of repaglinide. They are characterized using the elemental and molar conductance. The infrared, ¹H and ¹³C NMR spectra show the coordination mode of the metal ions to the repaglinide ligand. Magnetic susceptibility measurements and electronic spectra confirm the octahedral geometry around the metal center. The experimental values of FT-IR, ¹H, NMR, and electronic spectra are compared with theoretical data obtained by the density functional theory (DFT) using the B3LYP method with the LANL2DZ basis set. Analytical and spectral results suggest that the HL ligand is coordinated to the metal ions via two oxygen atoms of the ethoxy and carboxyl groups. The structural parameters of the optimized geometries of the ligand and the studied complexes are evaluated by theoretical calculations. The order of complexation energies for the obtained structures is as follows:

$$Fe(III) complex < Cu(II) complex < Zn(II) complex < Mn(II) complex.$$

The redox behavior of repaglinide and metal complexes are studied by cyclic voltammetry revealing irreversible redox processes. The presence of repaglinide in the complexes shifts the reduction potentials of the metal ions towards more negative values.

     

Metal-Induced Fluorescence Quenching of Photoconvertible Fluorescent Protein DendFP

Sensitive and accurate detection of specific metal ions is important for sensor development and can advance analytical science and support environmental and human medical examinations. Fluorescent proteins (FPs) can be quenched by specific metal ions and spectroscopically show a unique fluorescence-quenching sensitivity, suggesting their potential application as FP-based metal biosensors. Since the characteristics of the fluorescence quenching are difficult to predict, spectroscopic analysis of new FPs is important for the development of FP-based biosensors. Here we reported the spectroscopic and structural analysis of metal-induced fluorescence quenching of the photoconvertible fluorescent protein DendFP. The spectroscopic analysis showed that Fe²⁺, Fe³⁺, and Cu²⁺ significantly reduced the fluorescence emission of DendFP. The metal titration experiments showed that the dissociation constants (K_d) of Fe²⁺, Fe³⁺, and Cu²⁺ for DendFP were 24.59, 41.66, and 137.18 μM, respectively. The tetrameric interface of DendFP, which the metal ions cannot bind to, was analyzed. Structural comparison of the metal-binding sites of DendFP with those of iq-mEmerald and Dronpa suggested that quenchable DendFP has a unique metal-binding site on the β-barrel that does not utilize the histidine pair for metal binding.     

Determination of the complex formation constants for some water-soluble polymers with trivalent metal ions by differential pulse polarography

The formation of metal complexes between water-soluble polymers, poly(vinyl alcohol) [PVA], poly(N-vinylpyrrolidone) [PVP], poly(acrylamide) [PAAm] and poly(ethylene oxide) [PEO] with trivalent metal ions, Fe³⁺, Cr³⁺, and V³⁺ were studied by using differential pulse polarography (DPP). The general experimental observation is the shift of totally reversible reduction peaks (M³⁺+Hg+e^–M²⁺+Hg) towards more negative potentials when the complexing water-soluble polymers are added to the solution of trivalent metal ions. The negative shift in potential permitted the determination of complex formation constants (K_f) between trivalent metal ions and water soluble polymers. The complex formation constants for Fe³⁺, Cr³⁺, and V³⁺ ions with these polymers increased in the order of V³⁺>Cr³⁺>Fe³⁺.     

Studying the photophysical properties of a polymerizable 1,8‐naphthalimide dye and its copolymer with styrene as potential fluorescent sensors for metal cations

The photophysical characteristics of a polymerizable 1,8‐naphthalimide dye and its copolymer with styrene have been investigated. The functional properties of both low and high molecular weight fluorophores in the presence of different metal cations have been discussed with regard to their potential application as fluorosensors for the metal cations and protons. In acetonitrile solution the monomeric 1,8‐naphthalimide enhances its fluorescence emission in the presence of metal cations (Zn²⁺, Fe³⁺, Co²⁺, Pb²⁺, Cu²⁺, Ni²⁺, and Mn²⁺). In aqueous media the poly(St‐co‐MD) exhibits a selective response to Fe³⁺ cations. The monomeric and polymeric fluorophores also exhibit a considerable increase in their fluorescence intensity at acidic pH values (pH < 6) which suggest that they could be used as ON–OFF probes in analytical devices for signaling the presence of protons. Copyright © 2008 John Wiley & Sons, Ltd.     

Uptake of Divalent Metal Ions (Cu2+, Zn2+ and Cd2+) by Polysiloxane Immobilized Monoamine Ligand System

ABSTRACT

Porous solid siloxane polymers carrying a monoamine functional group of formula P-(CH₂)₃NH₂ (Where P- represents a siloxane framework silica like ) has been prepared by polycondensation of Si(OEt)₄ and (MeO)₃Si(CH₂)₃-NH₂. Treatment of aqueous solutions of divalent metal ions with the polysiloxane monoamine ligand system demonstrates that this material has high potential for preconcentration of metal ions (Cu²⁺, Zn²⁺ and Cd²⁺). The tendency of these divalent metal ions to chemisorb by the monoamine ligand system at the optimum conditions increases in the order: Cd²⁺ <Zn²⁺ <Cu²⁺. The optimum pH is 5.5 for copper and 6-7 for zinc and cadmium. The ammonia/ ammonium chloride buffer solution gave maximum uptake for all metal ions. It is also found that the uptake of copper ions is concentration dependent and is independent of the presence of other competing ions. The monoamine ligand system suffers from leaching of ligand containing groups upon treatment with acidic solutions. The highest leaching occurs at low pH.     

Synthesis,characterization and applications of polysiloxane networks with immobilized pyrogallol ligands

A porous, solid insoluble polysiloxane‐immobilized ligand system bearing pyrogallol active sites of the general formula P? (CH₂)₃? NH(CH₂)₃OC₆H₃(OH)₂ (where P represents [Si? O]_n siloxane network) has been prepared by the reaction of 3‐aminopropylpolysiloxane with 1,3‐dibromopropane followed by the reaction with pyrogallol. ¹³C CP‐MAS NMR and X‐ray photoelectron spectroscopy confirmed that the pyrogallol is chemically bonded to the siloxane backbone. Thermal analysis showed that the ligand system is stable under nitrogen at relatively high temperature. The polysiloxane–pyrogallol ligand system exhibits high potential for the uptake of the metal ions (Fe³⁺, Co²⁺, Ni²⁺ and Cu²⁺). Complexation of the pyrogallol ligand system for the metal ions at the optimum conditions was found to be in the order Fe³⁺ > Cu²⁺ > Ni²⁺ > Co²⁺. Copyright © 2005 John Wiley & Sons, Ltd.     

Uptake of Divalent Metal Ions (Cu2+, Zn2+ and Cd2+) by Polysiloxane Immobilized Glycinate Ligand System

ABSTRACT

Porous solid siloxane polymer carrying glycinate functional group of formula –(CH₂)₃NHCH₂COOH has been prepared by the sol-gel process. Treatment of aqueous solutions of divalent metal ions with the polysiloxane glycinate ligand system demonstrates that this material exhibits high potential for preconcentration of metal ions (Cu²⁺, Zn²⁺ and Cd²⁺). The ligand system chemisorbs these divalent metal ions, at optimum conditions, in the order: Cd²⁺ < Zn²⁺ < Cu²⁺. The uptake of copper ions is concentration dependent but it is independent on the presence of other competing ions. Treatment of the glycinate ligand system with acidic solution results in leaching of bound ligands. The highest leaching occurs in presence of copper ions at low pH     

1-(d-Glucopyranosyl-2′-deoxy-2′-iminomethyl)-2-hydroxynaphthalene as chemo-sensor for Fe in aqueous HEPES buffer based on colour changes observable with the naked eye

A new glucose-based C2-derivatized colorimetric chemo-sensor (L₁) has been synthesized by a one-step condensation of glucosamine and 2-hydroxy-1-naphthaldehyde for the recognition of transition metal ions. Among the eleven metal ions studied, viz., Mg²⁺, Ca²⁺, Mn²⁺, Fe²⁺, Fe³⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺ and Hg²⁺, L₁ results in visual colour change only in the presence of Fe²⁺, Fe³⁺and Cu²⁺ in methanol. However, in an aqueous HEPES buffer (pH 7.2) it is only the Fe³⁺ that gives a distinct visual colour change even in the presence of other metal ions, up to a concentration of 280 ppb. The changes have been explained based on the complex formed, and the composition has been determined to be 2:1 between L₁ and Fe³⁺ based on Job’s plot as well as ESI MS. The structure of the proposed complex has been derived based on HF/6-31G calculations.     

Fe2+ and Cu2+ Increase the Production of Hyaluronic Acid by Lactobacilli via Affecting Different Stages of the Pentose Phosphate Pathway

This study aimed at optimizing the production of hyaluronic acid by Lactobacillus acidophilus FTDC 1231 using response surface methodology and evaluating the effects of divalent metal ions along the production pathway using molecular docking. Among different divalent metal ions that were screened, only iron (II) sulphate and copper (II) sulphate significantly (P?<?0.05) affected the production of hyaluronic acid. Subsequent optimization yielded hyaluronic acid at concentration of 0.6152?mg/mL in the presence of 1.24 mol L^?1 iron (II) sulphate and 0.16 mol L^?1 of copper (II) sulphate (103 % increase compared to absence of divalent metal ions). Data from molecular docking showed Fe²⁺ improved the binding affinity of UDP-pyrophophorylase towards glucose-1-phosphate, while Cu²⁺ contributed towards the interaction between UDP-glucose dehydrogenase and UDP-glucose. We have demonstrated that lactobacilli could produce hyaluronic acid at increased concentration upon facilitation by specific divalent metal ions, via specific targets of enzymes and substrates along pentose phosphate pathway.     

Color Tuning in Garnet Oxides: The Role of Tetrahedral Coordination Geometry for 3 d Metal Ions and Ligand–Metal Charge Transfer (Band‐Gap Manipulation)

We explored garnet‐structured oxide materials containing 3d transition‐metal ions (e.g., Co²⁺, Ni²⁺, Cu²⁺, and Fe³⁺) for the development of new inorganic colored materials. For this purpose, we synthesized new garnets, Ca₃Sb₂Ga₂ZnO₁₂ ( I ) and Ca₃Sb₂Fe₂ZnO₁₂ ( II ), that were isostructural with Ca₃Te₂Zn₃O₁₂. Substitution of Co²⁺, Ni²⁺, and Cu²⁺ at the tetrahedral Zn²⁺ sites in I and II gave rise to brilliantly colored materials (different shades of blue, green, turquoise, and red). The materials were characterized by optical absorption spectroscopy and CIE chromaticity diagrams. The Fe³⁺‐containing oxides showed band‐gap narrowing (owing to strong sp–d exchange interactions between Zn²⁺ and the transition‐metal ion), and this tuned the color of these materials uniquely. We also characterized the color and optical absorption properties of Ca₃Te₂Zn_3−x Co_x O₁₂ (0<x ≤2.0) and Cd₃Te₂Zn_3−x Co_x O₁₂ (0<x ≤1.0), which display brilliant blue and green‐blue colors, respectively. The present work brings out the role of the distorted tetrahedral coordination geometry of transition‐metal ions and ligand–metal charge transfer (which is manifested as narrowing of the band gap) in producing brilliantly colored garnet‐based materials.     

Voltammetric study of metal ions binding by biindolizine heterocyclophanes and their acyclic analogues

The binding of ions Li⁺, Na⁺, K⁺, (group I), Mg²⁺, Al³⁺, Ga³⁺ (group II), Ca²⁺, Pb²⁺ (group III) ions, Ba²⁺ and paraquat by heterocyclophanes containing biindolizine and quinoxaline fragments connected by 3,6,9-trioxaundecane and 5,8,11,14,17-pentaoxageneicosane spacers, and also their acyclic analogues, in the acetonitrile-0.1 M Bu₄NBF₄ is studied by cyclic voltammetry. A conclusion is drawn that the ions of the group I are not bound by these compounds; the paraquat is not bound by heterocyclophane with the 5,8,11,14,17-pentaoxageneicosan spacers. For ions of the group II, reversible redox-switchable binding by the macrocycles with the 3,6,9-trioxaundecane and 5,8,11,14,17-pentaoxageneicosan spacers is observed: the initial compounds show the binding; their radical cations and dications do not. The binding of the ions of the group III and Ba²⁺ is determined by the macrocycles’ size. In particular, these ions are bound not only by the heterocyclophane with 3,6,9-trioxaundecane spacers but also by its radical cation or dication. The binding results in the corresponding dication stabilization. The heterocyclophane with the 5,8,11,14,17-pentaoxageneicosan spacers demonstrates the redox-switchable binding of Ca²⁺ and Pb²⁺ ions; no effect of Ba²⁺ ions on the cyclic voltammograms of this heterocyclophane was observed. In the ternary system “heterocyclophane with 3,6,9-trioxaundecane spacers + ions of the group II (Al³⁺, Ga³⁺) + ions of the group III (Ca²⁺, Pb²⁺)” either primary binding of the group III ion Pb2+ or concurrent binding of the ions of the group II and the group III, with the system’s reversible redox-switching from one metal complex to another, was observed.     

Some synthesized polymeric composite resins for the removal of Co(II) and Eu(III) from aqueous solutions

Summary The ion-exchange and sorption characteristics of new polymeric composite resins, prepared by gamma radiation were experimentally studied. The composite resins show high uptake for Co(II) and Eu(III) ions in aqueous solutions in a wide range of pH. The selectivity of the resins for Co(II) or Eu(III) species in presence of some competing ions and complexing agents (as Na⁺, Fe³⁺, EDTANa₂, etc.) was compared. Various factors that could affect the sorption behavior of metal ions (Co(II) and Eu(III)) on the prepared polymeric composite resins were studied such as ionic strength, contact time, volume mass ratio.     

A Highly Copper‐Selective Ratiometric Fluorescent Sensor Based on BODIPY

A new ratiometric fluorescent sensor ( 1 ) for Cu²⁺ based on 4,4‐difluoro‐4‐bora‐3a,4a‐diaza‐s‐indacene (BODIPY) with di(2‐picolyl)amine (DPA) as ion recognition subunit has been synthesized and investigated in this work. The binding abilities of 1 towards different metal ions such as alkali and alkaline earth metal ions (Na⁺, K⁺, Mg²⁺, Ca²⁺) and other metal ions ( Ba²⁺, Zn²⁺, Cd²⁺, Fe²⁺, Fe³⁺, Pb²⁺, Ni²⁺, Co²⁺, Hg²⁺, Ag⁺) have been examined by UV‐vis and fluorescence spectroscopies. 1 displays high selectivity for Cu²⁺ among all test metal ions and a ～10‐fold fluorescence enhancement in I₅₈₂/I₅₅₈ upon excitation at visible excitation wavelength. The binding mode of 1 and Cu²⁺ is a 1:1 stoichiometry determined via studies of Job plot, the nonlinear fitting of the fluorometric titration and ESI mass.     

Uptake behavior of americium on alginic acid and alginate polymer gels

The uptake behavior of Am³⁺ was investigated by using alginic acid and alginate polymer gels. The affinity of radioactive nuclides for carboxyl groups in gel matrices increased in the order of Na⁺ < Cs⁺ < Co²⁺ < Pd²⁺, Sr²⁺, Fe³⁺ < Eu³⁺, Am³⁺. Among alginate gels, calcium alginate exhibited relatively higher uptake rate and distribution coefficient of Am³⁺. The column packed with calcium alginate beads was effective for the removal of trace amounts of Am³⁺ from acidic nitrate solutions.     

Adsorption/desorption of Cd(II), Cu(II) and Pb(II) using chemically modified orange peel: Equilibrium and kinetic studies

Waste materials from industries such as food processing may act as cost effective and efficient biosorbents to remove toxic contaminants from wastewater. This study aimed to establish an optimized condition and closed loop application of processed orange peel for metals removal. A comparative study of the adsorption capacity of the chemically modified orange peel was performed against environmentally problematic metal ions, namely, Cd²⁺, Cu²⁺ and Pb²⁺, from aqueous solutions. Chemically modified orange peel (MOP) showed a significantly higher metal uptake capacity compared to original orange peel (OP). Fourier Transform Infrared (FTIR) Spectra of peel showed that the carboxylic group peak shifted from 1637 to 1644 cm⁻¹ after Pb (II) ions binding, indicated the involvement of carboxyl groups in Pb(II) ions binding. The metals uptake by MOP was rapid and the equilibrium time was 30 min at constant temperature and pH. Sorption kinetics followed a second-order model. The mechanism of metal sorption by MOP gave good fits for Freundlich and Langmuir models. Desorption of metals and regeneration of the biosorbent was attained simultaneously by acid elution. Even after four cycles of adsorption-elution, the adsorption capacity was regained completely and adsorption efficiency of metal was maintained at around 90%.     

Thermal Decomposition of Chloromethylated Poly(styrene)-PAN Resin and Its Complexes with Some Transition Metal Ions

The complexes formed by the chemically modified chloromethylated poly(styrene)-PAN (CMPS-PAN) as a resin chelating ion exchanger were characterized by infrared and potentiometry. The thermal degradation of pure CMPS-PAN resin and its complexes with Au³⁺, Cr³⁺, Cu²⁺, Fe³⁺, Mn²⁺ and Pt⁴⁺ in air atmosphere has been studied using thermal gravimetry (TG) and derivative thermal gravimetry (DTG). The results showed that four different steps accompany the decomposition of CMPS-PAN resin and its complexes with the metal ions. These stages were affected by the presence of the investigated metal ions. The thermal degradation of CMPS-PAN resin in the presence of the ions showed different stability of the resin in the following decreasing order: Au³⁺>Pt⁴⁺>Mn²⁺>Cu²⁺>Cr³⁺>Fe³⁺. On the basis of the applicability of a non-isothermal kinetic equation, the decomposition process was a first-order reaction. The activation energy, Ea, the entropy change, ΔS ^*, the enthalpy change, ΔH ^* and the Gibbs free energy of activation, ΔG ^* were calculated by applying the theory of the reaction rates. The effect of the different central metal ions on the calculated thermodynamic activation parameters was discussed. This revised version was published online in July 2006 with corrections to the Cover Date.