LES of Low to High Turbulent Combustion in an Elevated Pressure Environment

A subgrid scale flame surface density combustion model for the Large Eddy Simulation (LES) of premixed combustion is derived and validated. The model is based on fractal characteristics of the flame surface, assuming a self similar wrinkling of the flame between smallest and largest wrinkling length scales. Experimental and direct numerical simulation databases as well as theoretical models are used to derive a model for the fractal parameters, namely the cut-off lengths and the fractal dimension suitable in the LES context. The combustion model is designed with the intent to simulate low as well as high Reynolds number premixed turbulent flame propagation and with a focus on correct scaling with pressure. The combustion model is validated by simulations of turbulent Bunsen flames with methane and propane fuel at pressure levels between 0.1 MPa and 2 MPa and at turbulence levels of $0 < u^{\prime }/s_{L}^{0} < 11$ , conditions typical for spark ignition engines. The predicted turbulent flame speed is in a very good agreement with the experimental data and a smooth transition from resolved flame wrinkling to fully modelled, nearly subgrid-only wrinkling is realized. Evaluating the influence of mesh resolution shows a predicted mean flame surface and turbulent flame speed independent of mesh resolution for cases with 9–86 % resolved flame surface. Additional simulations of a highly turbulent jet flame at 0.1 MPa and 0.5 MPa and the comparison with experimental data in terms of flame shape, velocity field and turbulent fluctuations validates the model also at conditions typical for gas turbines.     

Flame Structure and Propagation in Turbulent Flame-Droplet Interaction: A Direct Numerical Simulation Analysis

Three-dimensional Direct Numerical Simulations (DNS) in canonical configuration have been employed to study the combustion of mono-disperse droplet-mist under turbulent flow conditions. A parametric study has been performed for a range of values of droplet equivalence ratio ?_d, droplet diameter a_d and root-mean-square value of turbulent velocity u^′. The fuel is supplied entirely in liquid phase such that the evaporation of the droplets gives rise to gaseous fuel which then facilitates flame propagation into the droplet-mist. The combustion process in gaseous phase takes place predominantly in fuel-lean mode even for ?_d>1. The probability of finding fuel-lean mixture increases with increasing initial droplet diameter because of slower evaporation of larger droplets. The chemical reaction is found to take place under both premixed and non-premixed modes of combustion: the premixed mode ocurring mainly under fuel-lean conditions and the non-premixed mode under stoichiometric or fuel-rich conditions. The prevalence of premixed combustion was seen to decrease with increasing droplet size. Furthermore, droplet-fuelled turbulent flames have been found to be thicker than the corresponding turbulent stoichiometric premixed flames and this thickening increases with increasing droplet diameter. The flame thickening in droplet cases has been explained in terms of normal strain rate induced by fluid motion and due to flame normal propagation arising from different components of displacement speed. The statistical behaviours of the effective normal strain rate and flame stretching have been analysed in detail and detailed physical explanations have been provided for the observed behaviour. It has been found that the droplet cases show higher probability of finding positive effective normal strain rate (i.e. combined contribution of fluid motion and flame propagation), and negative values of stretch rate than in the stoichiometric premixed flame under similar flow conditions, which are responsible for higher flame thickness and smaller flame area generation in droplet cases.     

Joint RANS/LES Approach to Premixed Flame Modelling in the Context of the TFC Combustion Model

We present an original timesaving joint RANS/LES approach to simulate turbulent premixed combustion. It is intended mainly for industrial applications where LES may not be practical. It is based on successive RANS/LES numerical modelling, where turbulent characteristics determined from RANS simulations are used in LES equations for estimation of the subgrid chemical source and viscosity. This approach has been developed using our TFC premixed combustion model, which is based on a generalization of the Kolmogorov’s ideas. We assume existence of small-scale statistically equilibrium structures not only of turbulence but also of the reaction zones. At the same time, non-equilibrium large-scale structures of reaction sheets and turbulent eddies are described statistically by model combustion and turbulence equations in RANS simulations or follow directly without modelling in LES. Assumption of small-scale equilibrium gives an opportunity to express the mean combustion rate (controlled by small-scale coupling of turbulence and chemistry) in the RANS and LES sub-problems in terms of integral or subgrid parameters of turbulence and the chemical time, i.e. the definition of the reaction rate is similar to that of the mean dissipation rate in turbulence models where it is expressed in terms of integral or subgrid turbulent parameters. Our approach therefore renders compatible the combustion and turbulent parts of the RANS and LES sub-problems and yields reasonable agreement between the RANS and averaged LES results. Combining RANS simulations of averaged fields with LES method (and especially coupled and acoustic codes) for simulation of corresponding nonstationary process (and unsteady combustion regimes) is a promising strategy for industrial applications. In this work we present results of simulations carried out employing the joint RANS/LES approach for three examples: High velocity premixed combustion in a channel, combustion in the shear flow behind an obstacle and the impinging flame (a premixed flame attached to an obstacle).     

Statistical Analysis of Turbulent Flame-Droplet Interaction: A Direct Numerical Simulation Study

Turbulent combustion of mono-disperse droplet-mist has been analysed based on three-dimensional Direct Numerical Simulations (DNS) in canonical configuration under decaying turbulence for a range of different values of droplet equivalence ratio (?_d), droplet diameter (a_d) and root-mean-square value of turbulent velocity (u^′). The fuel is supplied in liquid phase and the evaporation of droplets gives rise to gaseous fuel for the flame propagation into the droplet-mist. It has been found that initial droplet diameter, turbulence intensity and droplet equivalence ratio can have significant influences on the volume-integrated burning rate, flame surface area and burning rate per unit area. The droplets are found to evaporate predominantly in the preheat zone, but some droplets penetrate the flame front, reaching the burned gas side where they evaporate and some of the resulting fuel vapour diffuses back towards the flame front. The combustion process in gaseous phase takes place predominantly in fuel-lean mode even for ?_d > 1. The probability of finding fuel-lean mixture increases with increasing initial droplet diameter because of slower evaporation of larger droplets and this predominantly fuel-lean mode of combustion exhibits the attributes of low Damköhler number combustion and gives rise to thickening of flame with increasing droplet diameter. The chemical reaction is found to take place under both premixed and non-premixed modes of combustion and the relative contribution of non-premixed combustion to overall heat release increases with increasing droplet size. The statistical behaviours of the flame propagation and mode of combustion have been analysed in detail and detailed physical explanations have been provided for the observed behaviour.     

Effects of Turbulence on Self-sustained Combustion in Premixed Flame Kernels: A Direct Numerical Simulation (DNS) Study

The effects of mean flame radius and turbulence on self-sustained combustion of turbulent premixed spherical flames in decaying turbulence have been investigated using three-dimensional direct numerical simulations (DNS) with single step Arrhenius chemistry. Several flame kernels with different initial radius or initial turbulent field have been studied for identical conditions of thermo-chemistry. It has been found that for very small kernel radius the mean displacement speed may become negative leading ultimately to extinction of the flame kernel. A mean negative displacement speed is shown to signify a physical situation where heat transfer from the kernel overcomes the heat release due to combustion. This mechanism is further enhanced by turbulent transport and, based on simulations with different initial turbulent velocity fields, it has been found that self-sustained combustion is adversely affected by higher turbulent velocity fluctuation magnitude and integral length scale. A scaling analysis is performed to estimate the critical radius for self-sustained combustion in premixed flame kernels in a turbulent environment. The scaling analysis is found to be in good agreement with the results of the simulations.     

LES/PDF Modeling of Turbulent Premixed Flames with Locally Enhanced Mixing by Reaction

Large-eddy simulations (LES) combined with the transported probability density function (PDF) method are carried out for two turbulent piloted premixed methane-air jet flames (flame F1 and flame F3) to assess the capability of LES/PDF for turbulent premixed combustion. The conventionally used model for the sub-filter scale mixing time-scale (or the mixing frequency) fails to capture the premixed flames correctly. This failure is expected to be caused by the lack of the sub-filter scale premixed flame propagation property in the sub-filter scale mixing process when the local flame front is under-resolved. It leads to slower turbulent premixed flame propagation and wider flame front. A new model for specifying the sub-filter scale mixing frequency is developed to account for the effect of sub-filter scale chemical reaction on mixing, based on past development of models for the sub-filter scale scalar dissipation rate in premixed combustion. The new model is assessed in the two turbulent premixed jet flames F1 and F3. Parametric studies are performed to examine the new model and its sensitivity when combined with the different mixing models. Significantly improved performance of the new mixing frequency model is observed to capture the premixed flame propagation reasonably, when compared with the conventional model. The sensitivity of the flame predictions is found be relatively weak to the different mixing models in conjunction with the new mixing frequency model.     

甲烷/空气预混气体火焰的传播特征

利用高速纹影摄像等技术探讨了密闭管道内不同当量比的甲烷/空气预混气体火焰的传播特征。结果表明,当甲烷含量接近当量值时,预混气体火焰传播中会发生火焰阵面由向未燃区弯曲到向已燃区弯曲的转折过程,逐渐由层流燃烧转变成湍流燃烧,并形成Tulip火焰结构;当甲烷含量偏离当量值一定程度时,预混火焰呈现出典型的层流燃烧特征,不会发生火焰阵面由向未燃区弯曲到向已燃区弯曲的转折过程。Tulip火焰结构形成于火焰传播速度迅速降低的区间里,且只有当减速阶段的最大加速度的绝对值大于某一数值时才能形成;Tulip火焰结构是预混火焰由层流燃烧向湍流燃烧转变的一个中间过程。     

Heat Transfer Modeling in the Context of Large Eddy Simulation of Premixed Combustion with Tabulated Chemistry

Tabulated chemistry models like the Flamelet Generated Manifolds method are a good approach to include detailed information on the reaction kinetics in a turbulent flame at reasonable computational costs. However, so far, not all information on e.g. heat losses are contained in these models. As those often appear in typical technical applications with enclosed flames in combustion chambers, extensions to the standard FGM approach will be presented in this paper, allowing for the representation of non-adiabatic boundaries. The enthalpy as additional control variable for the table access is introduced, such that the chemistry database becomes three-dimensional with mixture fraction, reaction progress variable and enthalpy describing the thermo-chemical state. The model presented here is first validated with a two-dimensional enclosed Bunsen flame and then applied within the Large Eddy Simulations of a turbulent premixed swirl flame with a water-cooled bluff body and a turbulent stratified flame, where additional modeling for the flame structure using artificially thickened flames was included. The results are encouraging, as the temperature decrease towards the bluff body in the swirl flame and the cooling of the pilot flame exhaust gases in the stratified configuration can be observed in both experiments and simulation.     

Coupling tabulated chemistry with Large Eddy Simulation of turbulent reactive flows

A new modeling strategy is developed to introduce tabulated chemistry methods in the LES of turbulent premixed combustion. The objective is to recover the correct laminar flame propagation speed of the filtered flame front when the subgrid scale turbulence vanishes. The filtered flame structure is mapped by 1D filtered laminar premixed flames. Closure of the filtered progress variable and the energy balance equations are carefully addressed. The methodology is applied to 1D and 2D filtered laminar flames. These computations show the capability of the model to recover the laminar flame speed and the correct chemical structure when the flame wrinkling is completely resolved. The model is then extended to turbulent combustion regimes by introducing subgrid scale wrinkling effects on the flame front propagation. Finally, the LES of a 3D turbulent premixed flame is performed. To cite this article: R. Vicquelin et al., C. R. Mecanique 337 (2009).     

Assessing the Predictive Capabilities of Combustion LES as Applied to the Sydney Flame Series

Large Eddy Simulation (LES) and flamelet-based combustion models were applied to four bluff-body stabilized nonpremixed and partially premixed flames selected from the Sydney flame series, based on Masri’s bluff-body test rig (University of Sydney). Three related non-reacting flow cases were also investigated to assess the performance of the LES solver. Both un-swirled and swirled cases were studied exhibiting different flow features, such as recirculation, jet precessing and vortex breakdown. Due to various fuel compositions, flow rates and swirl numbers, the combustion characteristics of the flames varied greatly. On six meshes with different blocking structure and mesh sizes, good prediction of flow and scalar fields using LES/flamelet approaches and known fuel and oxidizer mass fluxes was achieved. The accuracy of predictions was strongly influenced by the combustion model used. All flames were calculated using at least two modeling strategies. Starting with calculations of isothermal flow cases, simple single flamelet based calculations were carried out for the corresponding reacting cases. The combustion models were then adjusted to fit the requirements of each flame. For all flame calculations good agreement of the main flow features with the measured data was achieved. For purely nonpremixed flames burning attached to the bluff-body’s outer edge, flamelet modeling including strain rate effects provided good results for the flow field and for most scalars. The prediction of a partially premixed swirl flame could only be achieved by applying a flamelet-based progress variable approach.     

Large-Eddy Simulation of Lean Premixed Turbulent Flames of Three Different Combustion Configurations using a Novel Reaction Closure

This large eddy simulation (LES) study is applied to three different premixed turbulent flames under lean conditions at atmospheric pressure. The hierarchy of complexity of these flames in ascending order are a simple Bunsen-like burner, a sudden-expansion dump combustor, and a typical swirl-stabilized gas turbine burner–combustor. The purpose of this paper is to examine numerically whether the chosen combination of the Smagorinsky turbulence model for sgs fluxes and a novel turbulent premixed reaction closure is applicable over all the three combustion configurations with varied degree of flow and turbulence. A quality assessment method for the LES calculations is applied. The cold flow data obtained with the Smagorinsky closure on the dump combustor are in close proximity with the experiments. It moderately predicts the vortex breakdown and bubble shape, which control the flame position on the double-cone burner. Here, the jet break-up at the root of the burner is premature and differs with the experiments by as much as half the burner exit diameter, attributing the discrepancy to poor grid resolution. With the first two combustion configurations, the applied subgrid reaction model is in good correspondence with the experiments. For the third case, a complex swirl-stabilized burner–combustor configuration, although the flow field inside the burner is only modestly numerically explored, the level of flame stabilization at the junction of the burner–combustor has been rather well captured. Furthermore, the critical flame drift from the combustor into the burner was possible to capture in the LES context (which was not possible with the RANS plus k–ɛ model), however, requiring tuning of a prefactor in the reaction closure.     

Experimental Measurement of Local Burning Velocity Within a Rotating Flow

The work presented in this paper details the implementation of a new technique for the measurement of local burning velocity using asynchronous particle image velocimetry. This technique uses the local flow velocity ahead of the flame front to measure the movement of the flame by the surrounding fluid. This information is then used to quantify the local burning velocity by taking into account the translation of the flame via convection. In this paper the developed technique is used to study the interaction between a flame front and a single toroidal vortex for the case of premixed stoichiometric methane and air combustion. This data is then used to assess the impact of vortex structure on flame propagation rates. The burning velocity data demonstrates that there is a significant enhancement to the rate of flame propagation where the flame directly interacts with the rotating vortex. The increases found were significantly higher than expected but are supported by burning velocities (Filatyev et al, Combust Flame 141:1?C21, 2005; Kobayashi et al, Proc Combust Inst 29:1793?C1800, 2002; Shepherd et al. 1998) found in turbulent flames of the same mixture composition. Away from this interaction with the main vortex core, the flame exhibits propagation rates around the value recorded in literature for unperturbed laminar combustion (Tahtouh et al, Combust Flame 159:1735?C1743, 2009; Hassan et al, Combust Flame 115:539?C550, 1998); Halter et al, Proc Combust Inst 30:201?C208, 2005; Coppens et al, Exp Therm Fluid Sci 31:437?C444, 2007).     

Optical Analysis and Qualitative Discrimination of Vortex-Flame Interaction in a Plane Premixed Shear Layer

To obtain practical schemes of vortex–flame interactions, a series of organized eddies formed in the plane premixed shear layer is investigated, instead of a single vortex ring or a single vortex tube. The plane premixed shear layer is first formed between two parallel uniform propane–air mixture streams. For getting clear qualitative pictures of vortex–flame interactions in the plane premixed shear layer, two extreme ignition points are assigned; one is assigned at the center of an organized eddy where the vortex motion plays an important role, the other at the midpoint between two adjacent organized eddies where the rolling-up motion prevails. A premixed flame is initiated by an electric discharge at one of the two assigned points and propagates either in the large scale organized eddy or along the interface between two uniform mixture streams. Propagation and deformation processes of the flame are observed using the simultaneously two-directional and high-speed Schlieren photography. The tangential velocity of organized eddy and the equivalence ratio of premixed shear flow are varied as two main parameters. The outline of propagating flame after the midpoint ignition is numerically analyzed by superposing the flame propagation having a constant burning velocity on the vortex flow field simulated with the discrete vortex method. The results obtained show that there exists another type of vortex–flame interaction in the plane shear layer in addition to the vortex bursting, and that it is caused by the rolling-up motion particular to the coherent structure in the plane shear layer and is simply named the vortex boosting. It is qualitatively concluded therefore that, in the ordinary turbulent premixed flames formed in the plane premixed shear layer, these two fundamental vortex-flame interactions get tangled with each other to augment the propagation velocity. An empirical expression which qualitatively takes into account of the effects of both vortex and chemical properties is finally proposed.     

Towards an Extension of TFC Model of Premixed Turbulent Combustion

In order to determine the mean rate of product creation within the framework of the Turbulent Flame Closure (TFC) model of premixed combustion, the model is combined with a simple closure of turbulent scalar flux developed recently by the present authors based on the flamelet concept of turbulent burning. The model combination is assessed by numerically simulating statistically planar, one-dimensional, developing premixed flames that propagate in frozen turbulence. The mean rate of product creation yielded by the combined model decreases too slowly at the trailing edges of the studied flames, with the effect being more pronounced at longer flame-development times and larger ratios of rms turbulent velocity u′ to laminar flame speed S _L . To resolve the problem, the above closure of turbulent scalar flux is modified and the combination of the modified closure and TFC model yields reasonable behaviour of the studied rate. In particular, simulations indicate an increase in the mean combustion progress variable associated with the maximum rate by u′/S _L , in line with available DNS data. Finally, the modified closure of turbulent scalar flux is validated by computing conditioned velocities and turbulent scalar fluxes in six impinging-jet flames. The use of the TFC model for simulating such flames is advocated.     

Linear-Eddy Model Formulated Probability Density Function and Scalar Dissipation Rate Models for Premixed Combustion

A tabulated, pseudo-turbulent Probability Density Function (PDF) model for premixed combustion is proposed. The Linear-Eddy Model (LEM) is used to construct the PDFs for a temperature-based progress variable in a premixed, turbulent methane/air V-flame produced by the Cambridge slot burner. As a second case study, the LEM PDFs are similarly compared to PDFs extracted from Direct Numerical Simulations (DNS) of a turbulent premixed flame. LEM demonstrates the ability to reproduce the salient features from experimental and DNS PDFs; moreover, it is able to better capture turbulent effects than previously suggested laminar flamelet PDF models. The Scalar Dissipation Rate (SDR) for premixed combustion is likewise investigated. The stochastic nature of LEM enables it to mimic the overall behaviors of turbulent reactions inexpensively and qualitatively. Crucially, LEM appears to be well suited for the preprocessing tabulation of PDF and SDR models for a number of premixed combustion simulation strategies.     

Subgrid Modeling of Turbulent Premixed Flames in the Flamelet Regime

Large eddy simulation (LES) models for flamelet combustion are analyzed by simulating premixed flames in turbulent stagnation zones. ALES approach based on subgrid implementation of the linear eddy model(LEM) is compared with a more conventional approach based on the estimation of the turbulent burning rate. The effects of subgrid turbulence are modeled within the subgrid domain in the LEM-LES approach and the advection (transport between LES cells) of scalars is modeled using a volume-of-fluid (VOF) Lagrangian front tracking scheme. The ability of the VOF scheme to track the flame as a thin front on the LES grid is demonstrated. The combined LEM-LES methodology is shown to be well suited for modeling premixed flamelet combustion. The geometric characteristics of the flame surfaces, their effects on resolved fluid motion and flame-turbulence interactions are well predicted by the LEM-LES approach. It is established here that local laminar propagation of the flamelets needs to be resolved in addition to the accurate estimation of the turbulent reaction rate. Some key differences between LEM-LES and the conventional approach(es) are also discussed. This revised version was published online in July 2006 with corrections to the Cover Date.     

Subgrid Scale Modeling in Large-Eddy Simulation of Turbulent Combustion Using Premixed Flamelet Chemistry

Large-eddy simulation (LES) of turbulent combustion with premixed flamelets is investigated in this paper. The approach solves the filtered Navier–Stokes equations supplemented with two transport equations, one for the mixture fraction and another for a progress variable. The LES premixed flamelet approach is tested for two flows: a premixed preheated Bunsen flame and a partially premixed diffusion flame (Sandia Flame D). In the first case, we compare the LES with a direct numerical simulation (DNS). Four non-trivial models for the chemical source term are considered for the Bunsen flame: the standard presumed beta-pdf model, and three new propositions (simpler than the beta-pdf model): the filtered flamelet model, the shift-filter model and the shift-inversion model. A priori and a posteriori tests are performed for these subgrid reaction models. In the present preheated Bunsen flame, the filtered flamelet model gives the best results in a priori tests. The LES tests for the Bunsen flame are limited to a case in which the filter width is only slightly larger than the flame thickness. According to the a posteriori tests the three models (beta-pdf, filtered flamelet and shift-inversion) show more or less the same results as the trivial model, in which subgrid reaction effects are ignored, while the shift-filter model leads to worse results. Since LES needs to resolve the large turbulent eddies, the LES filter width is bounded by a maximum. For the present Bunsen flame this means that the filter width should be of the order of the flame thickness or smaller. In this regime, the effects of subgrid reaction and subgrid flame wrinkling turn out to be quite modest. The LES-results of the second case (Sandia Flame D) are compared to experimental data. Satisfactory agreement is obtained for the main species. Comparison is made between different eddy-viscosity models for the subgrid turbulence, and the Smagorinsky eddy-viscosity is found to give worse results than eddy-viscosities that are not dominated by the mean shear. Paper presented on the Eccomas Thematic Conference Computational Combustion 2007, submitted for a special issue of Flow, Turbulence and Combustion.     

Direct Numerical Simulations of Premixed Turbulent Flames with Reduced Chemistry: Validation and Flamelet Analysis

Direct numerical simulation is a very powerful tool to evaluate the validity of new models and theories for turbulent combustion. In this paper, direct numerical simulations of spherically expanding premixed turbulent flames in the thin reaction zone regime and in the broken reaction zone regime are performed. The flamelet-generated manifold method is used in order to deal with detailed reaction kinetics. The computational results are analyzed by using an extended flame stretch theory. It is investigated whether this theory is able to describe the influence of flame stretch and curvature on the local burning velocity of the flame. It is found that if the full profiles of flame stretch and curvature through the flame front are included in the theory, the local mass burning rate is well predicted. The influence of several approximations, which are used in other existing theories, is studied. When flame stretch is assumed constant through the flame front or when curvature of the flame front is neglected, the theory fails to predict the local mass burning rate. The influence of using a reduced chemistry model is investigated by comparing flamelet simulations with reduced and detailed chemistry.     

A Lagrangian-based flame index for the transported probability density function method

We propose a new flame index for the transported probability density function(PDF) method. The flame index uses mixing flux projections of Lagrangian particles on mixture fraction and progress variable directions as the metrics to identify the combustion mode, with the Burke-Schumann solution as a reference. A priori validation of the flame index is conducted with a series of constructed turbulent partially premixed reactors. It indicates that the proposed flame index is able to identify the combustion mode based on the subgrid mixing information. The flame index is then applied the large eddy simulation/PDF datasets of turbulent partially premixed jet flames. Results show that the flame index separate different combustion modes and extinction correctly. The proposed flame index provides a promising tool to analyze and model the partially premixed flames adaptively.     

The Problems of the Turbulent Burning Velocity

The paper reviews the practical problems in measuring a turbulent burning velocity that gives the mass rate of burning. These largely centre on identifying an appropriate flame surface to associate with the turbulent burning velocity, u _t , and the density of the unburned mixture. Such a flame surface has been identified, in terms of the mean reaction progress variable, $\bar {c}$ , for explosive flame propagation in a fan-stirred bomb. Measurement of $\bar {c}$ makes possible an estimation of the flame surface density, ??, from the relationship ${\it \Sigma} =k\bar {c}\left( {1-\bar {c}} \right)$ . It is shown that in such explosions, mass rates of burning derived from the measured total flame surface area agreed well with those found from the measured turbulent burning velocity. Flamelet considerations identify appropriate dimensionless correlating parameters for u _t . As a result, correlations of turbulent burning velocity divided by the effective rms turbulent velocity, are plotted against the turbulent Karlovitz stretch factor, K, for different values of the Markstein number for flame strain rate, Ma_sr. These plots cover a wide range of variables, including pressure and fuels, and are indicative of different regimes of turbulent combustion. At the lower values of K, there is some evidence of increases in u _t and k due to high-frequency flame surface wrinkling arising from flame instabilities. These increase as Ma_sr becomes more negative. It is found from the developed value of the mean flame surface density throughout the flame brush that, to a first approximation, an increase in u _t for a given mixture is accompanied by a proportional increase in the volume of the brush. The analysis shows that the volume fraction of the turbulent flame brush that is reacting is quite small.