Surface-enhanced Raman scattering at the silver electrode/ionic liquid (BMIPF6) interface

This is the first report of in situ SER spectra of chemical species adsorbed on a Ag/room temperature ionic liquid (RTIL) interface. We have investigated the dependence of the SERS intensity of the RTIL derived from 1-n-butyl-3-methylimidazolium hexafluorophosfate (BMIPF6) adsorbed on a silver electrode. It has been shown that the BMI+ adsorbs on the silver electrode for potentials more negative than -0.4 V vs a Pt quasireference electrode (PQRE). In the -0.4 to -1.0 V potential range the SER spectra are similar to the Raman spectrum of the RTIL BMIPF6. At potentials more negative than -1.0 V some imidazolium ring vibrational modes and N-CH3 vibrations are enhanced, suggesting that the imidazolium ring is parallel to the surface and for potentials <-2.8 V the BMI+ is reduced to the BMI carbene. The potential dependence of the SERS intensities of Py adsorbed on a silver electrode in BMIPF6 has also been investigated. The results have shown that at potentials less negative than -0.8 V (vs PQRE) Py adsorbs at an end-on configuration forming an Ag-N bond. In the -0.9 to -1.4 V potential range Py molecules lie flat on the electrode surface and at potentials <-1.4 V Py is replaced by the BMI+. The electrochemical and SERS results have shown that Py has the effect of changing the oxidation of silver in that medium as well as the reduction of BMI+ to the BMI carbene. In the presence of Py the BMI+ reduction is observed at potentials near -2.4 V. The Ag electrode has presented SERS activity from 0.0 to -3.0 V.     

Porphyrin self-assembly at electrochemical interfaces: role of potential modulated surface mobility

The self-assembly of 5,10,15,20-tetra(4-pyridyl)-21H,23H-porphine (TPyP) on Au(111) electrodes was investigated. The adlayer structure was found to depend on the electrode potential. At positive potentials (>0.5V(SCE)), a disordered layer of TPyP is formed on the Au(111) electrode. STM images showed that the disordered molecules are immobile. At negative potentials (-0.2V(SCE)), however, the molecules are highly mobile and can no longer be imaged by STM, though they remain on the surface. At intermediate potentials (-0.2 to +0.2V(SCE)), the TPyP formed a highly ordered adlayer. Once the ordered adlayer is formed, it persists even after the potential is stepped to higher values (0.5-0.8 V(SCE)). These results can be explained by the role of potential modulated adsorbate-substrate interaction and surface mobility. This suggests the intriguing prospect of using electrode potential to tune surface interactions and to drive surface processes, e.g., molecular self-assembly, in electrochemical systems.     

锌电极上2-巯基吡啶自组装单层的原位表面增强拉曼光谱电化学观察

利用原位表面增强拉曼散射(SERS)技术, 观察了2-巯基吡啶在锌电极上单层吸附和脱附行为. SERS实验结果表明, 2-巯基吡啶分子主要通过巯基上的硫原子垂直吸附于锌表面. 原位SERS光谱电化学发现, 当外加电位达到－1.4 V vs. SCE时, 分子开始从表面脱附, 并伴随吸附构型变化, 在－1.6 V时发生完全脱附.     

Electrochemical impedance spectroscopy analysis of chalcopyrite CuFeS2 electrodes

A chalcopyrite CuFeS₂ electrode obtained from the “El Teniente” mine has been studied by Electrochemical Impedance Spectroscopy (EIS) in an alkaline solution for different oxidation potentials. The experimental results can be interpreted from a Randles equivalent circuit, V_dc<0.4 V vs. saturated calomel electrode (SCE), and a surface layer model for V_dc>0.4 V vs. SCE. From these results, the variation with the d.c. applied potentials of charge transfer electrical resistance of the redox reaction, the double layer capacitance and other characteristic parameters are considered.     

Study of the adsorption of fibrinogen on gold-coated silicon wafer by an impedance method

In 0.1 mol/l KH(2)PO(4)-Na(2)HPO(4) (pH 7.80) buffer solution, the potential of zero charge (PZC) and the open circuit potential of gold-coated silicon were determined to be about -0.6 and +0.10 V (vs SCE), respectively. The open circuit potential was higher than the PZC, which indicated that the surface of the gold-coated electrode had a positive charge. The ellipsometry experiment showed that the adsorption of fibrinogen onto the gold-coated silicon wafer surface arrived at a saturated state when the adsorption time exceeded 50 min. The percentage of surface without adsorbed protein, theta, was about 63%. This means that the proportion of surface actually occupied by fibrinogen was only about 37% after the adsorption arrived at saturation. The solution/protein capacitance value was determined in an impulse state around -0.59 V (vs SCE) and was stable (4.2x10(-5) F) at other potentials.     

Electrochemistry of a carotenoid self-assembled monolayer

A carotenoid self-assembled monolayer was prepared by dipping a gold electrode into a solution of 4^′-thioxo-β,β-caroten-4-one in acetonitrile. Electrochemistry of the surface layer was investigated by cyclic voltammetry in an aqueous solution. No electrochemical reaction was detected in the potential region between 0.5 and −0.6 V vs. SCE. The anodic reaction of adsorbed carotenoid occurs at 0.8 V, whereas the irreversible anodic desorption proceeds at 1.4 V in 0.01 M HClO₄. Formation of the surface layer resulted in a decrease of the charging current as well as in a strong inhibition of the electron transfer reaction for species such as Fe(CN)₆³⁻, Ru(NH₃)₆³⁺, and dissolved oxygen. Prolonged voltage cycling in the O₂ reduction range induced some changes in the surface layer characteristics that were tentatively accounted for by the cross-linking of adsorbed molecules under the effect of transient oxygen radicals.     

The riboflavin—dihydroriboflavin system in acidic medium on mercury: Part I. A chronocoulometric investigation

The riboflavin (RF)—dihydroriboflavin (DRF) system in 0.01 M HClO₄ + 0.09 M NaClO₄ has been studied on mercury by the single-step chronocoulometric technique. At ?0.040 V/SCE, where RF is still electro-inactive, this substance is adsorbed according to a Langmuir isotherm with an adsorption coefficient K_O = 5.2 × 10⁶ 1 mol^?1, giving rise to a single adsorbed monolayer. At potentials along the plateau of the RF polarographic adsorption prewave, as well as at more negative potentials, DRF is adsorbed with formation of two overlapping monolayers. This behaviour denotes strong attractive vertical interactions between overlapping adsorbed DRF molecules. The progressive shift in the chronocoulometric Q vs. E curve for electro-oxidation of adsorbed DRF towards more positive potentials with an increase in the surface concentration of DRF confirms the strength of these vertical interactions. The simultaneous presence, with formation of a charge-transfer complex, of adsorbed RF and DRF molecules along the plateau of the polarographic RF prewave, as postulated by Tedoradze and co-workers [21,22] is excluded.     

碱性直接醇燃料电池非铂阳极催化剂

以纳米Pd,Pd-Ru,Au和Au-Ru为碱性直接醇燃料电池非Pt阳极催化剂,考察了其对甲醇、乙醇和乙二醇的电氧化性能.结果表明,Pd在酸中对醇电氧化的催化活性很低,但在碱中表现出较高的催化活性,起波电势约为0.4V(vsRHE);引入Ru助催化剂后,起波电势负移约0.15V;Pd-Ru对乙醇的电氧化表现出很高的活性,在0.3～0.4V电势范围内其活性为Pt-Ru的4倍.Au在酸中几乎不催化醇类分子的电氧化,但在碱中表现出一定的催化活性,在高于0.6V(vsRHE)的电势范围内可观察到醇氧化阳极电流.Au-Ru的催化活性高于Au,但起波电势没有明显负移,这可能表明当电势不足够正时醇分子在Au表面的吸附脱氢步骤是速率控制步骤.     

中性介质中L-丝氨酸在Pt电极上解离吸附和氧化的原位FTIR研究

运用电化学循环伏安(CV)和原位红外反射光谱(in situ FTIRS)研究了中性介质中L-丝氨酸在Pt电极上的解离吸附和氧化过程. 结果表明, 在中性溶液中, 以两性离子形式存在的丝氨酸可以在很低的电位下(-0.6 V, vs. SCE)在Pt电极表面发生解离吸附, 生成强吸物种一氧化碳(COL)、(COB)和氰负离子(CN-). 研究结果还表明, 当电位低于0.7 V(vs. SCE)时, CN-能稳定存在于电极表面, 抑制丝氨酸的进一步反应. 在更高电位时则主要为丝氨酸分子的氧化过程.     

2-巯基苯并噻唑对铜缓蚀行为的表面增强红外光谱研究

2-巯基苯并噻唑(MBT)是Cu的高效缓蚀剂,但是缓蚀机理存在较大争议.本文通过电化学极化曲线从宏观角度对缓蚀效率进行评估,并利用原位衰减全反射-表面增强红外光谱技术结合理论计算研究了电位控制下的微观吸附构型.结果表明:在较高电位(大于0 V,相对饱和甘汞电极(SCE))下,MBT和金属Cu之间发生电子转移,MBT以硫醇式的环外S和N与金属Cu(I)离子配位在表面形成聚合物膜;在较低电位(小于0 V,vs SCE)下,MBT通过环外S原子以硫醇离子形式在金属Cu表面直立吸附.表面膜阻止了腐蚀介质的侵蚀,起到了较好的缓蚀效果.     

The riboflavin—dihydroriboflavin system in acidic medium on mercury: Part II. A polarographic investigation

Polarographic current—potential characteristics and current—time curves for the reduction of riboflavin (RF) to dihydroriboflavin (DRF) in 0.01 M HClO₄ + 0.09 M NaClO₄ have been examined in detail. It has thus been shown that the RF adsorption prewave is due to the formation of two overlapping adsorbed monolayers of DRF molecules. Lateral interactions of RF molecules between themselves, of DRF molecules between themselves and of RF with DRF molecules in the first adsorbed monolayer are weak, whereas vertical interactions between overlapping DRF molecules are relatively strong. This explains the abrupt increase in the slope of the RF adsorption prewave and its shift towards more positive potentials as soon as the second adsorbed monolayer of DRF starts to form. The so-called “normal” wave for RF reduction has a half-wave potential E^II_{$\text{1}\text{2}$} = ?0.180 V/SCE, practically coinciding with the formal potential of the RF/DRF couple, and a slope corresponding to a reversible two-electron reduction unaffected by semiquinone formation. The shape of polarographic mean current vs. potential curves has been accounted for through an approximate solution of the corresponding diffusional problem.     

聚邻甲苯胺的合成及物理化学性质

聚苯胺的导电性和电化学特性已被广泛地研究。最近,对苯胺衍生物的聚合物也开始了研究,如聚邻甲氧基苯胺、聚邻苯二胺和聚邻氨基酚,其中聚邻甲氧基苯胺是一种可溶性的导电高分子材料。为了探讨苯胺聚合的机理和苯胺上不同基团对聚苯胺性质的影响,我们使用了十六种苯     

Structure and electrochemistry of 4,4'-dithiodipyridine self-assembled monolayers in comparison with 4-mercaptopyridine self-assembled monolayers on Au(111)

4,4'-Dithiodipyridine (PySSPy) monolayers on Au(111) were investigated by cyclic voltammetry, X-ray photoelectron spectroscopy (XPS) and in situ scanning tunneling microscopy (STM). The studies were performed in solutions of different anions and pHs (0.1 M H2SO4, 0.1 M HClO4, 0.1 and 0.01 M Na2SO4, 0.1 and 0.01 M NaOH). The cyclic current-potential curves in H2SO4 show current peaks at about 0.4 V, which are absent for all other electrolytes at this potential. The XPS data suggest that PySSPy adsorbs via the S endgroup on the gold surface and the S-S bond breaks during adsorption. From the chemical shift of the N(ls) peak, it is concluded that in acidic media the self-assembled monolayer (SAM) is fully protonated, whereas in basic solution it is not. The pKa is estimated to be 5.3. STM studies reveal the existence of highly ordered superstructures for the SAM. In Na2SO4 and H2SO4, a (7 x mean square root of 3) structure is proposed. However, whereas in Na2SO4 solutions the superstructure does not change with potential, in 0.1 M H2SO4 the superstructure is observed only negative of the current peak at +0.4 V. At more positive potentials, the film becomes disordered. The results are compared to those for 4-mercaptopyridine (PyS) SAMs. XPS experiments and current-potential curves indicate that both molecules adsorb in the same manner on Au(111), that is, even in the case of PySSPy the adspecies is PyS. The STM results, however, call for a more subtle interpretation. While in Na2SO4 solutions the observed superstructures are the same for both SAMs, markedly different structures are found for PySSPy and PyS SAMs in 0.1 M H2SO4.     

In situ STM imaging and direct electrochemistry of Pyrococcus furiosus ferredoxin assembled on thiolate-modified Au111 surfaces

We have addressed here electron transfer (ET) of Pyrococcus furiosus ferredoxin (PfFd, 7.5 kDa) in both homogeneous solution using edge plane graphite (EPG) electrodes and in the adsorbed state by electrochemistry on surface-modified single-crystal Au111 electrodes, This has been supported by surface microscopic structures of PfFd monolayers, as revealed by scanning tunneling microscopy under potential control (in situ STM). Direct ET between PfFd in phosphate buffer solution, pH 7.9, and EPG electrodes is observed in the presence of promoters. Neomycin gives rise to a pair of redox peaks with a formal potential of ca -430 mV (vs SCE), corresponding to [3Fe-4S]1+/0. The presence of an additional promoter, which can be propionic acid, alanine, or cysteine, induces a second pair of redox peaks at approximately -900 mV (vs SCE) arising from [3Fe-4S]0/1-. A robust neomycin-PfFd complex was detected by mass spectrometry. The results clearly favor an ET mechanism in which the promoting effect of small organic molecules is through formation of promoter-protein complexes. The interaction of PfFd with small organic molecules in homogeneous solution offers clues to confine the protein on the electrode surface modified by the same functional group monolayer and to address diffusionless direct electrochemistry, as well as surface microstructures of the protein monolayer. PfFd molecules were found to assemble on either mercaptopropionic acid (MPA) or cysteine-modified Au111 surfaces in stable monolayers or submonolayers. Highly ordered (2 radical 3 x 5)R30 degrees cluster structures with six MPA molecules in each cluster were found by in situ STM. Individual PfFd molecules on the MPA layer are well resolved by in situ STM. Under Ar protection reversible cyclic voltammograms were obtained on PfFd-MPA/Au111 and PfFd-cysteine/Au111 electrodes with redox potentials of -220 and -201 mV (vs SCE), respectively, corresponding to the [Fe3S4]1+/0 couple. These values are shifted positively by 200 mV relative to homogeneous solution due to interactions between the promoting layers and the protein molecules. Possible mechanisms for such interactions and their ET patterns are discussed.     

绿脓杆菌Pseudomonas aeruginosa BTE-1直接电催化特征

本文研究厌氧条件下产电绿脓杆菌P. aeruginosa BTE-1的电化学催化特征。研究结果表明,P. aeruginosa BTE-1菌株在厌氧条件下,不能分泌可充当电子介体的绿脓菌素,但可通过在电极表面形成生物膜呈现了直接电催化性能。P. aeruginosa BTE-1在电极表面形成生物膜与其在特定电极电位下向电极传递电子的过程直接相关,适宜的电位为+0.2 V (vs. SCE),电位过高可能会损害P. aeruginosa BTE-1细胞。室温范围内升高温度可增强P. aeruginosa BTE-1生物膜电催化活性,但过高的温度(>60℃)会抑制生物膜电催化活性。循环伏安曲线显示,在厌氧条件下形成的P. aeruginosa BTE-1生物膜,具有与典型产电菌株G. sulfurreducens相近的氧化还原电位(-0.4 V~ -0.2 V vs. SCE)。P. aeruginosa BTE-1生物膜可电催化酵母抽取物和葡萄糖,但不能电催化醋酸盐。     

Rayleigh relaxation of pyrazine,pyridine and piperidine molecules adsorbed on the roughened Ag electrode by light beating technique

The light beating technique (intensity correlation algorithm) was employed to analyze the Rayleigh scattering from the roughened Ag electrode in very dilute (10^?4 M) pyrazine, pyridine and piperidine aqueous solutions containing KC1 (0.1 M). The relaxation time is longer when the applied voltages are between ?0.4 V and ?0.8 V (vs. SCE) where the Raman effect also shows greater surface enhancement. Also observed was that for the piperidine case the relaxation time reaches its maximum at the more negative applied voltage. The origin of the relaxation is attributed mainly to the desorption process of the pyrazine, pyridine and piperidine molecules off the roughened Ag electrode. An electrostatic model was also proposed for the interpretation of these experimental observations.     

Electro-oxidation of formic acid catalyzed by FePt nanoparticles

The electrocatalytic oxidation of formic acid at a gold electrode functionalized with FePt nanoparticles was studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) in a mixed solution of 0.1 M HCOOH and 0.1 M HClO4. The FePt bimetallic nanoparticles, with a mean diameter of 3 nm, were prepared by a chemical reduction method. The Au/FePt nanostructured electrode was prepared firstly by the deposition of FePt nanoparticles onto a clean Au electrode surface, followed by ultraviolet ozone treatment to remove the organic coating. In CV measurements, two well-defined anodic peaks were observed at +0.20 and +0.51 V (vs. a Ag/AgCl quasi-reference). The anodic peak at +0.20 V was attributed to the oxidation of HCOOH to CO2 on surface unblocked by CO, whereas the peak at +0.51 V was ascribed to the oxidation of surface-adsorbed CO (an intermediate product of HCOOH oxidation) and further oxidation of bulk HCOOH. From the onset potential and current density of the electro-oxidation of HCOOH, FePt nanoparticles exhibit excellent electrocatalytic activities as compared to Pt and other metal alloys. EIS measurements were carried out to further examine the reaction kinetics involved in the HCOOH electro-oxidation. The EIS responses were found to be strongly dependent on electrode potentials. At potentials more positive than -0.25 V (vs. Ag/AgCl), pseudo-inductive behavior was typically observed. At potentials between +0.3 and +0.5 V, the impedance response was found to reverse from the first quadrant to the second quadrant; such negative Faradaic impedance was indicative of the presence of an inductive component due to the oxidation of surface-adsorbed CO. The impedance responses returned to normal behavior at more positive potentials (+0.6 to +0.9 V). The mechanistic variation was attributed to the formation of different intermediates (CO or oxygen containing species) on the electrode surface in different potential regions. Two equivalent circuits were proposed to model these impedance behaviors.     

Electrochemical dimerization of 2-(2'-thienyl)pyridine adsorbed on Au(111) observed by in situ fluorescence

The study of heterodentate molecules adsorbed on metal electrodes provides an opportunity to expand the functionality of modified surfaces while offering insights into the surface and intramolecular electronic interactions of organic adsorbates. The adsorption of 2-(2'-thienyl)pyridine, a molecule containing both pyridine and thiophene moieties, on a Au(111) electrode is reported. Adsorption was characterized by electrochemistry in neutral and basic aqueous electrolyte and was compared to that of pyridine. The aqueous electrochemistry of thiophene on Au(111) was also characterized for comparison purposes. At negative potentials, in the presence of 2-(2'-thienyl)pyridine, a diffuse, pi-bonded monolayer was formed, and a phase transition to a close-packed N- and/or S-bonded configuration was observed near -0.4 V in a 1 mM solution of adsorbate, similar to that seen in pyridine on Au(111). The thiophene-like oxidative dimerization of the molecule was confirmed at positive potentials using in situ fluorescence microscopy by comparison with the spectrum of the chemically synthesized dimer.     

Characterization of mediated and non-mediated oxidase enzyme based glassy carbon electrodes

The performance and analytical characteristics of a glassy carbon glutaraldehyde immobilized glucose oxidase electrode have been established with regard to the direct detection of hydrogen peroxide produced from the reaction of glucose with oxygen. Measurements were performed at + 1.1 V vs. SCE, and selectivity was obtained by casting the surface with a cellulose acetate membrane. Results compared favorably with the classical platinum-enzyme probe. The mechanism of ascorbic acid interference in hydrogen peroxide detection is reported. Mediated detection was also investigated for oxidase enzymes (glucose oxidase and xanthine oxidase) immobilized on the bare glassy carbon electrode. The probes were characterized using a specific enzyme mediator in solution (phenazine methosulfate or dichlorophenol-indophenol) plus hexacyanoferrate(III) as an electrochemical mediator. The electrode was poised at + 0.36 V vs. SCE for the detection of hexacyanoferrate(II). The advantages of this dual mediator configuration include high stability and sensitivity of the electrochemical signal and the ability to use less positive potentials for increased selectivity. Application to other enzymes, such as hydrogenases, using such a binary redox configuration is suggested.     

Application of electrochemical impedance spectroscopy to the study of dioleoyl phosphatidylcholine monolayers on mercury

Electrochemical impedance spectroscopy has been applied to the analysis of the behavior of monolayers of dioleoyl phosphatidylcholine (DOPC) on a mercury electrode. Experiments were carried out in electrolytes KCl and NaCl (0.1 mol dm(-3)) and Mg(NO3)2 (0.05 mol dm(-3)), and the frequency dependence of the complex impedance was estimated between 65 000 and 0.1 Hz at potentials -0.4 to -1.5 V versus Ag/AgCl 3.5 mol dm(-3) KCl at uncoated and coated electrode surfaces. Experiments were also carried out in the presence of gramicidin A (gA). Between the potentials of -0.4 and -0.7 V, the DOPC monolayer behaves as an almost ideal capacitor with little frequency dispersion. At more negative potentials, the impedance data show the formation of defects (-0.7 to -0.85 V), ingression of electrolyte into the layer (capacitance peak approximately -0.935 V), reorientation of phospholipid-water structures (capacitance peak approximately -1.0 V), and initiation of phospholipid desorption (approximately -1.3 V). gA interaction with the phospholipid monolayer at -0.4 V is shown as an additional low-frequency element. A general "one capacitor model" in a RC series equivalent circuit is developed incorporating the frequency dispersion of the capacitance, distribution of the time constants of the dispersion, and a coefficient related to the interface between the solution and the coated electrode. This latter coefficient is the most robust and decreases at potentials approaching those coincident with the DOPC phase transitions.