Synergistic Catalysis of SnO2/Reduced Graphene Oxide for VO2+/VO2+ and V2+/V3+ Redox Reactions

In spite of their low cost, high activity, and diversity, metal oxide catalysts have not been widely applied in vanadium redox reactions due to their poor conductivity and low surface area. Herein, SnO₂/reduced graphene oxide (SnO₂/rGO) composite was prepared by a sol–gel method followed by high-temperature carbonization. SnO₂/rGO shows better electrochemical catalysis for both redox reactions of VO²⁺/VO₂⁺ and V²⁺/V³⁺ couples as compared to SnO₂ and graphene oxide. This is attributed to the fact that reduced graphene oxide is employed as carbon support featuring excellent conductivity and a large surface area, which offers fast electron transfer and a large reaction place towards vanadium redox reaction. Moreover, SnO₂ has excellent electrochemical activity and wettability, which also boost the electrochemical kinetics of redox reaction. In brief, the electrochemical properties for vanadium redox reactions are boosted in terms of diffusion, charge transfer, and electron transport processes systematically. Next, SnO₂/rGO can increase the energy storage performance of cells, including higher discharge electrolyte utilization and lower electrochemical polarization. At 150 mA cm⁻², the energy efficiency of a modified cell is 69.8%, which is increased by 5.7% compared with a pristine one. This work provides a promising method to develop composite catalysts of carbon materials and metal oxide for vanadium redox reactions.     

Manganese Oxide Nanoparticles/Reduced Graphene Oxide as Novel Electrochemical Platform for Immobilization of FAD and its Application as Highly Sensitive Persulfate Sensor

In this study, manganese oxide nanoparticles/reduced graphene oxide(MnOxNPs/rGO) was used as support for strong immobilization of flavin adenine dinucleotide(FAD). A thin film of rGO cast on the electrode surface, followed by performing electrodeposition of MnOxNPs at applied constant potential of +1.4 V vs. Ag/AgCl for 200 s. Finally, FAD was electrodeposited onto the rGO/MnOxNPs film by potential cycling between 1.0 to ?1.0 V in solution containing 1 mg ml^?1 FAD. Electrochemical properties and catalytic activity of GCE/rGO‐MnOxNPs/FAD toward persulfate (S₂O₈^2?) reduction was investigated. Under optimized condition, the concentration calibration range, detection limit, and sensitivity were 0.1 μM–2 mM, 90 nM and 125.8 nA/μM, respectively, using hydrodynamic amperometry technique.     

Synthesis,characterizations, and electrochemical studies of ZnO/reduced graphene oxide nanohybrids for supercapacitor application

Herein the present article reports the fabrication of ZnO/reduced graphene oxide (ZnG) nanohybrid following a reduction-based process using a non-hazardous material, i.e., ascorbic acid. The morphology, structure, and bonding in the nanohybrid were analyzed using different techniques. Atomic force microscopy and scanning electron microscopy images show spherical particles of ZnO distributed over reduced graphene oxide (rGO). The X-ray diffraction analysis gives calculated values of crystallite size for ZnO as 15.62 nm. The successful incorporation of ZnO nanoparticles into rGO was confirmed using energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy analyses. The electrochemical studies were performed using an electrolyte (0.5 M H₂SO₄). The calculated value of specific capacitance for the nanohybrid was 345 Fg^-1, which was found to be almost double as compared to that of rGO, which is having a value of only 190.5 Fg^-1 at the same scan rate. The nanohybrid also showed excellent capacitance retention after 1,000 cycles.     

Electrochemical‐Reduction‐Assisted Assembly of a Polyoxometalate/Graphene Nanocomposite and Its Enhanced Lithium‐Storage Performance

Herein, we present an electrochemically assisted method for the reduction of graphene oxide (GO) and the assembly of polyoxometalate clusters on the reduced GO (rGO) nanosheets for the preparation of nanocomposites. In this method, the Keggin‐type H₄SiW₁₂O₄₀ (SiW₁₂) is used as an electrocatalyst. During the reduction process, SiW₁₂ transfers the electrons from the electrode to GO, leading to a deep reduction of GO in which the content of oxygen‐containing groups is decreased to around 5 %. Meanwhile, the strong adsorption effect between the SiW₁₂ clusters and rGO nanosheets induces the spontaneous assembly of SiW₁₂ on rGO in a uniformly dispersed state, forming a porous, powder‐type nanocomposite. More importantly, the nanocomposite shows an enhanced capacity of 275 mAh g^?1 as a cathode active material for lithium storage, which is 1.7 times that of the pure SiW₁₂. This enhancement is attributed to the synergistic effect of the conductive rGO support and the well‐dispersed state of the SiW₁₂ clusters, which facilitate the electron transfer and lithium‐ion diffusion, respectively. Considering the facile, mild, and environmentally benign features of this method, it is reasonable as a general route for the incorporation of more types of functional polyoxometalates onto graphene matrices; this may allow the creation of nanocomposites for versatile applications, for example, in the fields of catalysis, electronics, and energy storage.     

Dendritic Hematite Nanoarray Photoanode Modified with a Conformal Titanium Dioxide Interlayer for Effective Charge Collection

This paper describes the introduction of a thin titanium dioxide interlayer that serves as passivation layer and dopant source for hematite (α‐Fe₂O₃) nanoarray photoanodes. This interlayer is demonstrated to boost the photocurrent by suppressing the substrate/hematite interfacial charge recombination, and to increase the electrical conductivity by enabling Ti⁴⁺ incorporation. The dendritic nanostructure of this photoanode with an increased solid–liquid junction area further improves the surface charge collection efficiency, generating a photocurrent of about 2.5 mA cm⁻² at 1.23 V versus the reversible hydrogen electrode (vs. RHE) under air mass 1.5G illumination. A photocurrent of approximately 3.1 mA cm⁻² at 1.23 V vs. RHE could be achieved by addition of an iron oxide hydroxide cocatalyst.     

Improvement in the Performance of Composite Cathode via Solid Electrolyte for High Electrochemical Performance of Li–S Battery

Commercialization of Li–S in present scenario is obstructed by poor performance of cathode and its compatibility with electrolyte used. Here in this work, in order to improve the electrochemical performance all solid state Li–S battery, solid electrolyte (SE) formed by composition of lithium sulfide (Li₂S) and phosphorus pentasulfide (P₂S₅) combinedly called LPS is used. The modified carbon in the form of graphene oxide (GO) and reduced graphene oxide (rGO) as additive is used to provide better electron conduction pathway. High conductivity of the order 10⁻⁴ S cm⁻¹ of prepared LPS overcomes the major drawback of insulating nature of sulfur. The coin cells are fabricated by using above mentioned material as a cathode material, LPS as SE, and lithium foil as anode. The prepared nanocomposites are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) to study structural and morphological properties. Energy dispersive X-ray spectroscopy (EDS) images of the cathode surface confirms the uniform spreading of material. The electrochemical performance of coin cell is studied by Galvanostatic charge-discharge plot at 0.1 C to check the compatibility of composite and electrolyte prepared. The cells having additive material GO and rGO with host sulfur show better results as compared to the cell having pristine sulfur.     

Low‐Temperature Solid‐State Microwave Reduction of Graphene Oxide for Transparent Electrically Conductive Coatings on Flexible Polydimethylsiloxane (PDMS)

Microwaves (MWs) are applied to initialize deoxygenation of graphene oxide (GO) in the solid state and at low temperatures (～165 °C). The Fourier‐transform infrared (FTIR) spectra of MW‐reduced graphene oxide (rGO) show a significantly reduced concentration of oxygen‐containing functional groups, such as carboxyl, hydroxyl and carbonyl. X‐ray photoelectron spectra confirm that microwaves can promote deoxygenation of GO at relatively low temperatures. Raman spectra and TGA measurements indicate that the defect level of GO significantly decreases during the isothermal solid‐state MW‐reduction process at low temperatures, corresponding to an efficient recovery of the fine graphene lattice structure. Based on both deoxygenation and defect‐level reduction, the resurgence of interconnected graphene‐like domains contributes to a low sheet resistance (～7.9×10⁴ Ω per square) of the MW‐reduced GO on SiO₂‐coated Si substrates with an optical transparency of 92.7 % at ～547 nm after MW reduction, indicating the ultrahigh efficiency of MW in GO reduction. Moreover, the low‐temperature solid‐state MW reduction is also applied in preparing flexible transparent conductive coatings on polydimethylsiloxane (PDMS) substrates. UV/Vis measurements indicate that the transparency of the thus‐prepared MW‐reduced GO coatings on PDMS substrates ranges from 34 to 96 %. Correspondingly, the sheet resistance of the coating ranges from 10⁵ to 10⁹ Ω per square, indicating that MW reduction of GO is promising for the convenient low‐temperature preparation of transparent conductors on flexible polymeric substrates.     

中空分级结构Fe3O4@C/rGO复合材料的合成及其储锂性能

以氧化石墨烯(GO)为基底,Fe(NO_3)_3·9H_2O、异丙醇、甘油为原料,通过溶剂热法和后续热处理过程2步合成了Fe_3O_4@C/rGO复合材料,实现了碳包覆的Fe_3O_4纳米粒子自组装形成的分级结构空心球在氧化石墨烯片上的原位生长。采用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)和恒流充放电等手段分析了材料的物理化学性能与储锂性能。结果表明,该复合材料在5.0 A·g~(-1)的电流密度下,仍有437.7 mAh·g~(-1)的可逆容量,在1.0 A·g~(-1)下循环200圈后还有587.3 mAh·g~(-1)的放电比容量。这主要归因于还原态氧化石墨烯(rGO)对碳包覆Fe_3O_4分级空心球整体结构稳定性和导电性的提高。     

High solar-light photocatalytic activity of using Cu3Se2/rGO nanocomposites synthesized by a green co-precipitation method

Current work presents a facile, cost-effective, and green method to synthesize copper selenide nanostructures and copper selenide/graphene nanocomposites. The products were synthesized by a co-precipitation method by glycine amino acid as a green surfactant and graphene oxide (GO) sheets as a graphene source. X-ray diffraction patterns (XRD) of the products indicated that the products were Cu₂Se₃ with tetragonal phase. Fourier transform infrared (FTIR) spectroscopy and the XRD patterns indicated that the GO sheets were changed into reduced GO (rGO) during the synthesis process. Scanning and transmission electron microscopy (SEM and TEM) images showed the nanoparticles (NPs) that were decorated on rGO sheets had the significantly smaller size in compared to the pristine NPs. UV-vis results revealed that, the absorption peak of the products were in the visible region with a band-gap value between 1.85 eV and 1.95 eV. Finally, the products were applied as photocatalytic materials to remove Methylene Blue (MB) dye under solar-light and visible-light irradiation conditions. It was observed; the rGO had a significant role in enhancing the photocatalytic performance of the products and Cu₂Se₃/rGO (15%) could degrade more than 91% and 73% of MB only during 1 h under solar-light and visible-light sources, respectively.     

Tannic Acid Modified Electrochemical Biosensor for Glucose Sensing Based on Direct Electrochemistry

A novel glucose biosensor was constructed through the immobilization of glucose oxidase (GOx) on gold nanoparticles (Au NPs) deposited, and chemically reduced graphene oxide (rGO) nanocomposite. In the synthesis, tannic acid (TA) was used for the reduction of both graphene oxide, and Au³⁺ to rGO, and Au NPs, respectively. Also, by harnessing the π‐π interaction between graphene oxide and TA, and protein‐TA interaction, a novel nanocomposite for the fabrication of a third generation biosensor was successfully constructed. Upon the oxidation of TA to quinone, which is easily reducible at the negative potential range, enhanced electron transfer was obtained. The cyclic voltammetry (CV) results demonstrated a pair of well‐defined and quasi‐reversible redox peaks of active site molecule of GOx. The biosensor exhibited a linear response to glucose concentrations varying from 2 to 10 mM with a sensitivity of 18.73 mA mM⁻¹ cm⁻². The fabricated biosensor was used for the determination of glucose in beverages.     

Synthesis of Ultrastable Ag Nanoplates/Polyethylenimine–Reduced Graphene Oxide and Its Application as a Versatile Electrochemical Sensor

Investigations on Ag nanostructures/reduced graphene oxide composites have been frequently reported, yet the morphology control of those loaded Ag nanocrystals is still challenging. We herein develop a facile method to grow triangular Ag nanoplates (AgP) on polyethylenimine‐modified reduced graphene oxide (AgP/PEI‐rGO). The AgP/PEI‐rGO hybrids show unexpected high stability against chloride ions (Cl^?) and hydrogen peroxide (H₂O₂), which is possibly due to the strong interaction between surface Ag atoms with the amine groups of PEI. In the chronoamperometry measurements for detecting H₂O₂, N₂H₄, and NaNO₂, the AgP/PEI‐rGO hybrid shows very wide linear ranges (usually 10^?6–10^?2 mol L^?1 for H₂O₂, N₂H₄, and NaNO₂) and low detection limits (down to ≈1×10^?7 mol L^?1), which demonstrate the promising electrochemical sensor applications of these metal/graphene hybrids with well‐defined morphologies and facets. In addition, this strategy could be extended to the deposition of other noble metals on rGO with controlled morphologies.     

A Novel Enzymatic Glucose Biosensor and Nonenzymatic Hydrogen Peroxide Sensor Based on (3‐Aminopropyl) Triethoxysilane Functionalized Reduced Graphene Oxide

In the present study, a novel enzymatic glucose biosensor using glucose oxidase (GOx) immobilized into (3‐aminopropyl) triethoxysilane (APTES) functionalized reduced graphene oxide (rGO‐APTES) and hydrogen peroxide sensor based on rGO‐APTES modified glassy carbon (GC) electrode were fabricated. Nafion (Nf) was used as a protective membrane. For the characterization of the composites, Fourier transform infrared spectroscopy (FTIR), X‐ray powder diffractometer (XRD), and transmission electron microscopy (TEM) were used. The electrochemical properties of the modified electrodes were investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and amperometry. The resulting Nf/rGO‐APTES/GOx/GC and Nf/rGO‐APTES/GC composites showed good electrocatalytical activity toward glucose and H₂O₂, respectively. The Nf/rGO‐APTES/GC electrode exhibited a linear range of H₂O₂ concentration from 0.05 to 15.25 mM with a detection limit (LOD) of 0.017 mM and sensitivity of 124.87 μA mM⁻¹ cm⁻². The Nf/rGO‐APTES/GOx/GC electrode showed a linear range of glucose from 0.02 to 4.340 mM with a LOD of 9 μM and sensitivity of 75.26 μA mM⁻¹ cm⁻². Also, the sensor and biosensor had notable selectivity, repeatability, reproducibility, and storage stability.     

氧化石墨烯浓度对还原氧化石墨烯/ZnS电化学性能的影响

以氧化石墨烯(GO)、乙酸锌(Zn(CH₃COO)₂)和硫脲为原料,采用水热法成功制备了还原氧化石墨烯/ZnS(rGO/ZnS)复合材料,并将该材料用作锂离子电池负极。高导电性的 rGO可以为锂离子和电子的传输提供有效的路径,ZnS可以提供较高的理论比容量。rGO/ZnS复合材料在rGO与纳米级高度分散的类球形ZnS颗粒协同作用下展现了较好的嵌锂容量和循环性能。当GO质量浓度为2 mg·mL^-1时制备的rGO/ZnS复合材料的倍率性能最好,循环稳定性最佳。     

Phosphorus‐Modified Tungsten Nitride/Reduced Graphene Oxide as a High‐Performance,Non‐Noble‐Metal Electrocatalyst for the Hydrogen Evolution Reaction

Phosphorus‐modified tungsten nitride/reduced graphene oxide (P‐WN/rGO) is designed as a high‐efficient, low‐cost electrocatalyst for the hydrogen evolution reaction (HER). WN (ca. 3 nm in size) on rGO is first synthesized by using the H₃[PO₄(W₃O₉)₄] cluster as a W source. Followed by phosphorization, the particle size increase slightly to about 4 nm with a P content of 2.52 at %. The interaction of P with rGO and WN results in an obvious increase of work function, being close to Pt metal. The P‐WN/rGO exhibits low onset overpotential of 46 mV, Tafel slope of 54 mV dec^?1, and a large exchange current density of 0.35 mA cm^?2 in acid media. It requires overpotential of only 85 mV at current density of 10 mA cm^?2, while remaining good stability in accelerated durability testing. This work shows that the modification with a second anion is powerful way to design new catalysts for HER.     

Core–Shell LiFePO4/Carbon‐Coated Reduced Graphene Oxide Hybrids for High‐Power Lithium‐Ion Battery Cathodes

Core‐shell carbon‐coated LiFePO₄ nanoparticles were hybridized with reduced graphene (rGO) for high‐power lithium‐ion battery cathodes. Spontaneous aggregation of hydrophobic graphene in aqueous solutions during the formation of composite materials was precluded by employing hydrophilic graphene oxide (GO) as starting templates. The fabrication of true nanoscale carbon‐coated LiFePO₄‐rGO (LFP/C‐rGO) hybrids were ascribed to three factors: 1) In‐situ polymerization of polypyrrole for constrained nanoparticle synthesis of LiFePO₄, 2) enhanced dispersion of conducting 2D networks endowed by colloidal stability of GO, and 3) intimate contact between active materials and rGO. The importance of conducting template dispersion was demonstrated by contrasting LFP/C‐rGO hybrids with LFP/C‐rGO composites in which agglomerated rGO solution was used as the starting templates. The fabricated hybrid cathodes showed superior rate capability and cyclability with rates from 0.1 to 60 C. This study demonstrated the synergistic combination of nanosizing with efficient conducting templates to afford facile Li⁺ ion and electron transport for high power applications.     

氧化石墨烯浓度对还原氧化石墨烯/ZnS电化学性能的影响

以氧化石墨烯(GO)、乙酸锌(Zn(CH₃COO)₂)和硫脲为原料,采用水热法成功制备了还原氧化石墨烯/ZnS(rGO/ZnS)复合材料,并将该材料用作锂离子电池负极。高导电性的 rGO可以为锂离子和电子的传输提供有效的路径,ZnS可以提供较高的理论比容量。rGO/ZnS复合材料在rGO与纳米级高度分散的类球形ZnS颗粒协同作用下展现了较好的嵌锂容量和循环性能。当GO质量浓度为2 mg·mL^-1时制备的rGO/ZnS复合材料的倍率性能最好,循环稳定性最佳。     

Enhanced dielectric properties of poly(dimethyl siloxane) bimodal network percolative composite with chemically modified graphene

Bimodal network composite was prepared using a two-step method containing graphene modified by γ-(2, 3-epoxypropoxy) propyl trimethoxysilane (KH560), short chain poly(dimethyl siloxane) (C_S-PDMS) and long chain poly(dimethyl siloxane) filled with treated fumed silica (C_L-h-PDMS). A series of composites with different filler contents (including reduced graphene oxide and reduced graphene oxide grafted with KH560, referred to rGO and KrGO, respectively) were prepared to explore their percolation thresholds (fc). We discover that the dielectric constant and loss of 1.32 vol% KrGO/h-PDMS composite were 18.8 and 0.13 at 10² Hz before fc, respectively, which was 2.1 and 0.12 times that of rGO/h-PDMS, and 6.6 and 2.1 times that of pure h-PDMS. The origin is that KH560 insulting layer increases the interlayer distance of graphene sheets to cut down the leakage current. In addition, the modulus of 1.32 vol% KrGO/h-PDMS is less than 3 MPa.     

Reduced graphene oxide-porous In2O3 nanocubes hybrid nanocomposites for room-temperature NH3 sensing

Metal oxide semiconductors (MOS)-reduced graphene oxide (rGO) nanocomposites have attracted great attention for room-temperature gas sensing applications. The development of novel sensing materials is the key issue for the effective detection of ammoniagas at room temperature. In the present work, the novel reduced graphene oxide (rGO)-In₂O₃ nanocubes hybrid materials have been prepared via a simple electrostatic self-assembly strategy. Characterization results exhibit that the intimate interfacial contact between In₂O₃ nanocubes and the rGO sheets are achieved. Particularly, the as-prepared rGO/In₂O₃ nanocomposites displayed high sensitivity, fast response and excellent selectivity towards ammonia (NH₃) at room-temperature, which clearly uncovers the merit of structural design and rational integration with rGO sheets. The superior gas sensing performance of the rGO/In₂O₃ nanocomposites can be attributed to the synergetic effects of rGO sheets and porous In₂O₃ nanocubes. The reported synthesis offers a general approach to rGO/MOS-based semiconductor composites for room-temperature gas sensing applications.     

Electrochemical and FTIR spectroscopic study of CO2 reduction at a nanostructured Cu/reduced graphene oxide thin film

Here we report a facile approach to synthesize a novel nanostructured thin film comprising Cu nanoparticles (NPs) and reduced graphene oxide (rGO) on a glassy carbon electrode (GCE) via the direct electrochemical reduction of a mixture of cupper and graphene oxide (GO) precursors. The effect of the applied potential on the electrochemical reduction of CO₂ was investigated using linear sweep voltammetric (LSV) and chronoamperometric (CA) techniques. Carbon monoxide and formate were found as the main products based on our GC and HPLC analysis. The electrochemical reduction of CO₂ at the Cu/rGO thin film was further studied using in situ ATR-FTIR spectroscopy to identify the liquid product formed at different applied cathodic potentials. Our experimental measurements have shown that the nanostructured Cu/rGO thin film exhibits an excellent stability and superb catalytic activity for the electrochemical reduction of CO₂ in an aqueous solution with a high current efficiency of 69.4% at − 0.6 V vs. RHE, promising for the efficient electrochemical conversion of CO₂ to valuable products.     

还原石墨/氧化锌复合薄膜的制备及其光电转换性能

本工作研究不同过程还原的氧化石墨rGO/ZnO(reduced graphiteoxide/ZnO)复合膜的可见光激发光电转换性能。氧化石墨(GO)经KOH还原处理或NaBH4还原处理后,和氧化锌溶胶混合,通过旋涂法和热处理在F掺杂SnO2薄膜导电玻璃(FTO)衬底上形成复合薄膜。采用XRD、FTIR、FE-SEM、XPS、UV-Vis等方法对复合薄膜的晶相结构、微观形貌等进行表征,并测试了复合薄膜在可见光照射下的光电转换性能。GO的预处理过程对复合薄膜的结构影响显著,采用NaBH4对GO处理更有利于形成均匀薄膜。光电流测试结果表明不同复合薄膜均能实现可见光照射下产生光电流,其原理为rGO的光激发电子跃迁到ZnO,而空穴在rGO中迁移,在rGO与ZnO界面实现光生载流子分离。其中NaBH4处理后的rGO/ZnO复合薄膜光电流密度最大,达6×10-7A·cm-2。