7—[（4—甲基2—胂酸基苯）偶氮]—8—羟基喹啉—5—磺酸荧光光度法测定氟

本文介绍了７－［（４－甲基－２－胂酸基苯）偶氮］－８－羟基喹啉－５－磺酸的合成方法以及性能，详细研究了氟对该试剂与铝形成的荧光的熄灭作用，建立了荧光法测定微量氟的新方法。应用于水样和牙膏中的氟的测定，效果良好。     

高浓度F~--Al~(3+)体系的热力学分析及氟的测定

设定了Visual minteq软件F~--Al~(3+)体系的物种及平衡常数。模拟滴定和实验滴定结果的相似性证明了软件设定的合理。对F-(0.01/0.1 mol/L)-Al~(3+)(0.02 mol/L)-OH-体系的模拟和分析表明,当F与Al摩尔比相差大时,体系平衡物种分布不同,OH-掩蔽铝的机理也不同,但是在p H值11~12铝都被成功掩蔽;不同的反应机理导致F与Al摩尔比大的体系模拟和滴定曲线差别较大。进一步模拟得到了此p H值区间的最大可掩蔽铝浓度。考虑OH-对氟离子电极的影响,最终确定高氟(0.01~0.1 mol/L)高铝体系氟的测定条件:控制p H值为(11.5±0.2),不大于0.02 mol/L的铝。误差分析表明,当电势测定误差较大时,标准曲线法比标准加入法误差小。     

Fluorimetric determination of fluoride in a flow assembly integrated on-line to an open/closed FIA system to remove interference by solid phase extraction

A simple flow injection fluorimetric method for fluoride determination is proposed. The method is based on the enhanced fluorescence of quercitin-Zr(IV) complex when fluoride ion is present in the sample. An open/closed FIA manifold with a mini-column of Dowex 50W X8 resin was used to remove the most important interference (aluminum). The two FIA assemblies were integrated on-line to automate the pretreatment of the water sample and fluoride determination. The calibration graph was linear over the range 0.1-3.0 mug ml(-1) of fluoride with a correlation coefficient of 0.999 and LOD 0.06 mug ml(-1). The relative standard deviation was 2.5% and the sample throughput was 52 h(-1) without pretreatment and 10 h(-1) with pretreatment of the sample. The method was applied to the determination of fluoride in water samples.     

Determination of aluminum oxide in and on high-purity aluminum by a phenol dissolution method

A simple rapid determination of aluminum oxide in aluminum is described. Aluminum reacts with phenol at 180°C forming aluminum phenoxide but aluminum oxide does not. After the reaction, the aluminum oxide is filtered off and brought into aqueous solution by fusion with potassium hydrogensulfate for determination by atomic absorption spectrometry or by the 8-quinolinol spectrophotometric method. The reaction between aluminum and phenol is stoichiometric. The procedure is applicable to the determination of aluminum oxide in commercial aluminum metals of various forms. The method is relatively rapid and appears to be superior to the conventional bromine—methanol method.     

铝灰及其浸出液中氟的测定

铝灰中的氟化物是铝灰中的环境危害因子.使用X射线荧光光谱(XRF)法、X射线衍射(XRD)法对15份铝灰样品进行了元素及物相组成检测,使用SPSS 25.0对数据进行因子分析和聚类分析,将15份样品分成四类,从每类中选择1～2个样品,共选取5份样品作为代表进行后续实验.使用离子色谱法和氟离子选择电极法对铝灰浸出液中氟离...     

Determination of Fluoride by Fluorescence Quenching

Abstract

A fluorescence quenching method for the determination of fluoride ion over the concentration range from 10^?9 to 10^?6M is presented. The fluoride ion is added to the fluorescent chelate of aluminum(III) and PAN [1- (2-pyridylazo)-2-naphthol]: the fluoride preferentially complexes the aluminum (III), displacing nonfluorescent PAN. Of the anions tested as possible interferences at equimolar levels, phosphate interferred seriously and iodide interferred somewhat.     

Fluorometric Determination of Trace Amounts of Fluoride Ion Using an Expanded Porphyrin

A highly selective and sensitive method of fluorometry is described for determination of the fluoride ion at the parts per billion level via the ion-pair complex formation of the fluoride ion with an expanded prophyrin [2,23-diethyl-8,17-bis(2-ethoxycarbonylethyl)-3,7,12,13,18,22-hexamethylsapphyrin (H₃sap)]. The ion-pair complex gives out an enhanced fluorescence intensity at 680 nm on excitation at 450 nm. Since the present method is based on a direct reaction of the fluoride ion with the sappyrin, a 200-fold amount of the aluminum (III) ion [10⁻⁴M (M = mol dm⁻³)] and a 2000-fold amount of the iron(III) ion (10⁻³M) over the fluoride ion did not interfere with determination of the fluoride ion at concentrations as low as 5 × 10⁻⁷M in the presence of 1,2-diaminocyclohexane-N,N,N′,N′-teraacetic acid. The proposed method was applied to determination of the fluoride ion in various water samples (tap water, river water, rain water, underground water, and hot spring water) and satisfactory results were obtained.     

Elimination of interference of aluminum ion by a novel resin prepared from desferrioxamine and polyallylamine beads and its application to the determination of fluoride ion

A novel functional resin for the selective adsorption of aluminum was prepared from desferrioxamine(DF) and polyallylamine(PAA) resin. The primary amino group of DF was conjugated with PAA by glutaraldehyde(GA). The resin was found to be effective for the elimination of interference caused by aluminum ion on the determination of fluoride ion. A new determination system for low levels of fluoride ion in the presence of aluminum ion was developed by the use of DF-PAA resin combined with anion exchange resin loaded with alizarin fluorine blue sulfonate; 3-[NN-di(carboxymethyl)aminomethyl)-1,2-dihydroxyanthraquinone-5-sulfonate (AFBS) - lanthanum complex, which was a functional resin for selective collection of fluoride ion.     

Etude de l'action de l'ion fluor sur la laquethorium-spadns

The reaction of fluoride with thorium—SPADNS lake was studied in detail with particular reference to the effects of pH and media. Two methods for the determination of microgram amounts of fluoride based on the reaction are described. The spectrophotometric method developed is more suitable for routine use, but the colorimetric titration method is less sensitive to the effect of large amounts of electrolyte.     

Kinetochromic spectrophotometry-I Determination of fluoride by catalysis of the zirconium-xylenol orange reaction

The reaction between slightly aged solutions of zirconyl chloride and Xylenol Orange is catalysed by the presence of substoi-chiometric amounts of fluoride, phosphate, arsenate, sulphate, citrate or oxalate. The reaction provides a method for determining fluoride in amounts from 0.5 to 5 mug in a final volume of 100 ml. This kineto-chromic reaction provides an effective molar absorptivity of 2.0 x 10(5) for the fluoride ion. The colour reaches maximal development within 90 min and remains stable thereafter for 60 min, when measured against a reaction system blank containing no fluoride. Because of its substoichiometric nature the reaction may not be used for the determination of large amounts of fluoride.     

Determination of fluoride ions by titration with aluminum chloride to a preset potential

A procedure is proposed for determining fluoride ions based on titration with an aluminum chloride solution to a fixed potential. The procedure allows for the significant reduction of the determination error for fluoride ions due to the error of measuring the potential in comparison with direct potentiometry. The applicability of the procedure is confirmed by the results of determining fluoride ions in mixtures modeling the composition of Poles’e fluorinated cooking salt.     

Field determination of fluoride in drinking water using a polymeric aluminium complex of 5-(2-carboxyphenylazo)-8-hydroxyquinoline impregnated paper

A simple field method which allows the determination of fluoride in drinking water with a small handheld instrument called Arsenator was developed. Arsenator is a commercially available instrument which was used successfully for reliable determination of arsenic. In the proposed method the functionality of the Arsenator which is based on a photometric measurement of a spot on the reagent paper is expanded to analyse fluoride. A polymeric aluminium complex of 5-(2-carboxyphenylazo)-8-hydroxyquinoline (LH₂) has been prepared as a new specific reagent for fluoride. Job's method of continuous variation was adopted for the determination of the composition of the coloured complex, which was further characterized by UV-VIS spectroscopic studies. The molar absorptivity of the complex formation is 8.48?×?10³?L?mol^?1?cm^?1 at 410?nm. The coloured complex reacts with fluoride on an impregnated paper where its colour changes are dependent on the concentration of fluoride in water samples. The change in the colour was measured using the Arsenator. The method allows a reliable determination of fluoride in the range 0.3 to 2.0?mg?L^?1. Further spectophotometric determinations of fluoride in drinking water were also studied. The determination is based on the reaction of aluminium complex with fluoride in the examined samples. Beer's law is obeyed in the range 0.3 to 2.0?mg?L^?1 of fluoride at 495?nm. Sensitivity, detection limit and quantitation limit of the method were found to be 0.251?±?0.007?µg^?1?mL, 0.1?mg?L^?1 and 0.3?mg?L^?1, respectively. The optimum reaction conditions and other analytical conditions were evaluated. The effect of interfering ions on the determination is described. There is no interference by nitrate or chloride. Sulphate interfered only at high concentrations which are not expected in drinking water.     

抑制动力学荧光法测定痕量氟

在酸性介质中,利用氟离子对Fe(Ⅲ）催化H2O2氧化罗丹明6G使其荧光猝灭的抑制作用,建立了动力学荧光法测定痕量氟离子新方法,方法的线性范围为0.020-0.180μg/mL,检出限为8.70ng/mL。本法已用于牙膏中氟的含量测定。     

A catalytic-kinetic method for the determination of traces of fluoride in biological material

A catalytic-kinetic method for the determination of nanogram amounts of fluoride, based on its inhibiting action on the catalyst in the zirconium-catalyzed reaction between perborate and iodide, is described. The rate measurements are accomplished very simply by using a Landolt reaction system with a biamperometric detection of the induction period. The standard deviation in the working range 19–190 ng of fluoride (1–10 nmol) is ± 2 ng. The method can be made specific by combining it with a separation of the fluoride by microdiffusion. This has been demonstrated by analyzing biological material and comparing the results with the fluoride contents obtained with other methods.     

On-line flow injection solid sample introduction, leaching and potentiometric determination of fluoride in phosphate rock

A flow injection method with on-line solid sample dissolution was developed for the determination of fluoride in phosphate rock. The fluoride was selectively leached (98-102.4 % recovery) from a 50-mg powdered phosphate rock sample with 0.50 M citric acid. Using the zone sampling technique the fluoride in the buffered leachate was determined by injecting 87 μL into the carrier stream using a fluoride ion-selective electrode detector. The sensing element of the electrode was housed in a home-made sleeve-type flow-through cell. On-line solid sample digestion with 0.50 M citric acid at 55 °C resulted in minimum dissolution of interfering iron and aluminum ions with improved accuracy and calibration linearity. The incorporation of relatively high level of fluoride in the carrier stream (40 μg mL⁻¹) facilitated the determination of high levels of fluoride in phosphate rock (up to 4.1%) with out the need for excessive on-line dilution.The optimized flow system was applied for the determination of fluoride in phosphate rocks samples and a reference material at a rate of nine samples per hour with a relative standard deviation (n = 5) of 2.95-4.0 %. Comparison of the proposed flow injection method with the standard method, which involves steam distillation from sulfuric acid solution and manual titration with thorium nitrate, showed no evidence of bias at the 95% confidence level.     

Fluoride microdetermination and its application to the analysis of rocks,soils, precipitation,and airborne dust

A method for the routine determination of nanogram amounts of fluoride is described. In a one-vessel technique, the fluoride is separated from the matrix by diffusion and then determined kinetically by its inhibiting effect on the zirconium-catalysed reaction between perborate and iodide. The method is applied to the analysis of geochemical materials, rain water, and aerosol filter samples.     

Indirect Spectrophotometric Determination of Fluoride In Water With Zirconium-Spadns By Flow Injection Analysis

Abstract

The zirconium-SPADNS method for the determination of fluoride based on the effect of fluoride ion on the color system (Zr-SPADNS), has been adapted to the continuous flow spectrophotometry. A manifold consisting of two lines was used. the decrease in the absorbance of Zr-SPADNS reagent at 590 nm is linear with fluoride concentration in the range 0.00-3.5 ppm. the method has a detection limit of 0.02 ppm fluoride. At a sampling rate of 50 determinations per hour, the precision was about 1% relative standard deviation. the method is applied to the determination of fluoride in natural water samples. the good agreement between the results obtained by this method and those obtained by a potentiometric method using a fluoride ion-selective electrode, show that the new method is potentially suitable for routine analysis. the effects of reaction conditions, flow parameters, and interferences on the FIA-spectrophotometric signals are reported. amount of interfering ion is present in quantity great enough to produce an error of 0.1 ppm or more, the sample must be distilled¹⁷     

A new method for fluoride determination by using fluorophores and dyes anchored onto MCM-41

A new colourimetric and fluorimetric method for fluoride determination in aqueous samples based on the specific reaction between fluoride and silica has been developed and applied on real samples.     

Enhancement of Demasking of Fluoride Ion From its Aluminum Complexes by Dilution in the Determination With a Fluoride Ion-Selective Electrode

Abstract

In the determination of fluoride ion with an ion-selective electrode the permissible concentration of aluminum increases markedly with decreasing the fluoride concentration in 0.5M citrate buffer solutions at pi I 6. As the accuracy is constant over a concentration range down to 10^?5 M F^? where a Nernstian relation holds fluoride determinations can be accomplished by the successive dilution method. The dilution steps are repeated until the last two results are in agreement, while the concentration of citrate is kept constant. As the ionic strength is kept constant with citrate, the addition of sodium chloride to the buffer is not necessary. Several samples, especially glasses, have been analyzed successfully.     

电感耦合等离子体原子发射光谱(ICP-AES)法测定再生锌原料中铜、铅、铁、铟、镉、砷、钙、铝

采用硝酸、盐酸、氢氟酸(氟化氢铵)、高氯酸分解样品,电感耦合等离子体原子发射光谱法测定了再生锌原料中铜、铅、铁、铟、镉、砷、钙、铝的量。其测定范围:ω(Cu):0.01%～0.60%;ω(Pb):0.10%～5.00%;ω(Fe):0.10%～5.00%;ω(In):0.0100%～0.200%;ω(Cd):0.010%～3.00%;ω(As):0.10%～2.00%;ω(Ca):0.10%～10.00%;ω(Al):0.10%～4.00%。各元素的加标回收率为93%～113%。方法准确、快速、可靠,适用于再生锌原料中铜、铅、铁、铟、镉、砷、钙、铝量的同时测定。