宽调谐范围垂直腔面发射激光器特性分析及设计

运用光学传输矩阵和有限元方法对波长可调谐垂直腔面发射激光器(VCSELs)的波长调谐范围进行了研究.对中心波长为980nm的可调谐VCSELs的波长调谐特性和微电子机械系统(MEMS)悬臂梁结构进行了设计，并进行了实验研究.结果表明，MEMS可调谐VCSELs调谐特性同时受到光波谐振腔结构和悬臂梁最大位移的共同影响.在悬臂梁几何尺寸和激光器有源区结构一定的条件下，通过优化可调谐VCSELs的牺牲层厚度可实现大范围波长调谐.同时，对可调谐VCSELs整体结构进行了设计，计算结果显示波长调谐范围达到30nm以 关键词： 悬臂梁 可调谐垂直腔面发射激光器     

注入电流对垂直腔面发射激光器横模特性的影响

对980nm氧化限制型垂直腔面发射激光器横模进行测试和研究,理论上从时间、空间变量的速率方程出发,利用空间积分法分析了典型电注入参数对弱折射率导引垂直腔面发射激光器(VCSELs)横模行为的影响,通过实验测试,得到VCSELs的横模光场分布情况,并与理论分析进行对比,得出相应的实验结果,在氧化孔径不变的情况下,随着注入电流的增加,载流子分布从有源区中心向边缘移动,模式从低阶基模向高阶模转变,并发生了较强的模式竞争以及载流子空间烧孔效应,最终导致基模强度的降低.另一方面,通过比较不同注入孔径下高阶模的发生时 关键词： 横模 垂直腔面发射激光器 空间烧孔现象 模式竞争     

基于偏振旋转耦合1550nm垂直腔面发射激光器环形系统产生多路高质量混沌信号

提出了一种基于三个单向偏振旋转耦合1550 nm垂直腔面发射激光器(1550 nm-VCSELs)构成的环形系统获取多路高质量混沌信号的方案.利用自旋反转模型,数值研究了该环形系统中三个VCSELs的偏振分辨非线性动力学特性;利用自相关和互信息方法讨论了注入强度和频率失谐对三个VCSELs中各偏振分量输出时间序列的时延特征(TDS)的影响.研究结果表明:通过选择合适的注入强度和频率失谐,三个VCSELs均可同时输出X-偏振分量(X-PC)和Y-偏振分量(Y-PC)的平均功率可比拟的混沌信号,而且这些混沌信号的TDS通过进一步优化耦合参数可得到较好的抑制.在此基础上,进一步对三个VCSELs输出的六路混沌信号之间的相关性进行了分析,给出了除同一VCSEL输出的X-PC与Y-PC之间存在较强的相关性外其他信号之前关联性较弱的参数范围.     

基于椭偏光谱仪的石英晶体1310nm处双折射率的精密测量

为了对石英晶体在通讯波段1 310 nm处的双折射率进行精密测量,基于椭偏光谱仪对P和S两方向上偏振光相位差的精密测量原理,在透射模式下,通过对琼斯矩阵的分析,设计了一种精密测量晶体双折射率的方法,并在室温(22℃)下对通讯波段1 310 nm处石英晶体的双折射率进行了精密测量,测量结果和对误差的分析显示,此方法给出的...     

大功率垂直腔面发射激光器的相干性测量与分析

通过有机化学气象沉积(MOCVD)技术在n型GaAs衬底上生长制作了发射波长为850nm的VCSELs4×4列阵器件,介绍了VCSELs的制作工艺流程.对器件进行了相干性测量,计算了干涉条纹可见度,分析了影响干涉条纹可见度的因素.     

理论研究电流注入对垂直腔面发射激光器多横模行为的影响

从包含时空变量的速率方程出发,针对弱折射率导引垂直腔面发射激光器(VCSELs),利用空间积分法分析了典型电注入参数对VCSELs多横模行为的影响,在不降低模型准确性的前提下提高了仿真效率。仿真结果表明,注入盘孔径和注入环越小、注入强度越低以及电流扩散越弱时,VCSELs更易实现单横模工作;反之,VCSELs高阶横模开始出现并呈现较强的模式竞争,引发了载流子空间烧孔效应,并导致基模强度降低。进一步得出,在环形注入方式下,高阶模式更容易出现且彼此间的竞争较盘形注入时强。     

激光在PERC晶硅电池中背面点接触电极制备中的应用

在经过Al2O3全钝化发射极钝化局部背接触(PERC)结构电池的背面实现良好的接触电极一直是制约着PERC高效电池向产业化推广的重要因素之一。本文采用532 nm激光烧蚀背面钝化介质层方法和传统的光刻工艺来实现背面电极的局部接触,并对两种方法进行详细的比较与分析。对激光烧蚀和激光烧结两种不同的局部接触电极制备方式进行了对比,发现激光烧蚀是更为适宜的工艺方式。相较于激光烧结,以激光烧蚀方式制备的电池的串联面接触电阻从10.7Ω.cm2降到1.24Ω.cm2,效率从4.2%提高到10.7%。     

1550 nm垂直腔面发射激光器的特征参量随温度的变化

在采用自旋反转模型分析垂直腔面发射激光器（VCSELs）动力学行为的过程中,为了正确预测VCSELs的动力学行为,需要准确给出自旋反转模型中光场衰减速率k、总反转载流子衰减速率γ_N、线性二向色性系数γ_a、线性双折射系数γ_p、自旋反转速率γ_s和线宽增强因子α这6个特征参量.本文对1550 nm VCSELs在自由运行和平行光注入下的输出特性进行实验分析,获取了这6个特征参量的值,并着重研究了当激光器温度在10.00–30.00 ℃范围内变化时,这6个特征参量呈现的变化趋势.研究结果表明,随着温度的逐渐升高,γ_p整体呈现逐渐增加的趋势,γ_a,γ_s,γ_N和k呈现复杂的变化趋势,而α则呈现逐渐减小的趋势.     

关于制备1315nm 45°入射高反射镜的实验研究

从优化膜系、控制膜厚、改善膜面、均衡应力等四个方面开展了实验研究工作 ,为制备 1 31 5nm 4 5°高反射镜提供一些判断实验数据 ,并提出改进的方法 ,从而使制备的高反射膜取得满意的结果 :反射率大于 99.8%。     

表面等离子体调制的纳米孔径垂直腔面发射激光器

在普通850nm垂直腔面发射激光器基础上制备了表面等离子体调制的纳米孔径垂直腔面发射激光器.当小孔直径为200nm，周围光栅的周期为400nm时，在15mA驱动电流下最大输出光功率达到了0.3mW.介绍了该器件的制备工艺，并从实验和理论两方面分析了周期性光栅结构对光束的约束作用.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.