光子晶体光纤飞秒激光非线性放大系统的耦合动力学过程研究

构建了掺镱大模场面积单偏振光子晶体光纤飞秒激光非线性放大系统. 讨论了腔内净色散量和抽运功率对振荡级输出参数的影响和振荡级参数对放大级输出参数的影响. 在本实验条件下, 当腔内净色散量取较大负色散时, 振荡级直接输出的脉冲更宽, 且携带更少的啁啾. 当振荡级抽运4.53 W时, 选择最接近变换极限的脉冲作为种子脉冲, 放大级在60 W抽运时输出压缩后无基底的短脉冲, 宽度为45.7 fs, 平均功率28 W. 振荡级抽运功率增加到5.08 W, 放大级抽运70 W时, 获得最高输出功率34.5 W, 对应脉宽53.5 fs.     

低重复率的Ti:Al2O3飞秒激光放大器研究

本文报道了重复频率为10Hz的Ti:Al₂O₃飞秒激光放大器的研究.基于脉冲啁啾放大技术和采用再生/多通放大装置,得到了能量为8mJ的放大光脉冲,在该放大系统中,激光脉冲获M净增益约8×10⁷.     

High-energy femtosecond Yb-doped all-fiber monolithic chirped-pulse amplifier at repetition rate of 1 MHz

A high-energy femtosecond all ytterbium fiber amplifier based on a chirped-pulse amplification(CPA) technique at a repetition rate of 1 MHz seeded by a dispersion-management mode-locked picosecond broadband oscillator is studied.We find that the compressed pulse duration is dependent on the amplified energy,the pulse duration of 804 fs corresponds to the maximum amplified energy of 10.5 μJ,while the shortest pulse duration of 424 fs corresponds to the amplified energy of 6.75 μJ.The measured energy fluctuation is approximately 0.46% root mean square(RMS) over 2 h.The low-cost femtosecond fiber laser source with super-stability will be widely used in industrial micromachines,medical therapy,and scientific studies.     

等离子体密度对激光拉曼放大机理的影响

等离子体中的背向拉曼散射机理可以用来产生超短超强的激光脉冲. 本文采用粒子模拟方法模拟研究了等离子体密度对激光拉曼放大过程的影响. 研究发现, 过低的等离子体密度会导致等离子体波提前波破而降低能量转换效率; 而过高的等离子体密度又会导致其他不稳定性的快速增长, 限制作用距离和输出能量. 因此, 拉曼放大机理的最佳等离子体密度应处于等离子体波破的密度阈值附近, 可以获得最高的能量转换效率和能量输出. 另外, 空间频谱分析显示放大激光的强度饱和主要来自于自相位调制不稳定性的发展. 利用10¹³ W·cm^-2的抽运激光脉冲, 模拟证实拉曼放大机理可有效地将种子激光的强度从10¹³ W·cm^-2 放大到10¹⁷ W·cm^-2, 脉宽压缩到40 fs, 且能量转换效率达到58%.     

利用非线性脉冲预整形实现脉冲快速自相似放大

报道了一种通过预先对信号光脉冲非线性整形, 进而在光纤放大器中实现自相似演化的方法. 利用透射光栅对和普通单模光纤组成被动脉冲整形装置, 预先优化脉冲的时域宽度和光谱质量, 使脉冲在光纤放大器中快速演化到自相似子. 研究中首先通过数值模拟对比, 说明了非线性整形对脉冲实现快速自相似放大的关键作用, 提高了放大器输出脉冲质量, 减小了去啁啾脉冲宽度. 实验中, 通过优化非线性整形输出, 在2.2 m 长的掺Yb³⁺光纤中, 在一定抽运功率范围内均实现了脉冲自相似放大, 去啁啾后得到脉冲宽度60 fs 的变换极限脉冲输出. 这种非线性脉冲预整形方法有效减小了 自相似演化所需光纤长度, 同时降低了自相似放大对种子源质量的要求, 首次将全正色散光纤锁模激光器成功用于自相似放大, 促进了当前自相似放大系统的全光纤化. 关键词： 非线性整形 光纤放大器 自相似放大 飞秒激光     

高功率钕玻璃啁啾脉冲放大系统光谱整形

增益窄化效应限制了啁啾脉冲放大系统输出的最短脉冲宽度,需要对注入放大系统的种子啁啾脉冲进行光谱整形,以保证放大后的啁啾脉冲光具有足够的带宽并满足特定的光谱分布.理论上假定放大后啁啾脉冲的光谱分布为高斯分布或超高斯分布,对"百焦耳级钕玻璃啁啾脉冲放大系统"进行逆运算.研究发现,所需种子啁啾光的能量、带宽以及压缩后脉冲的信噪比都与该分布密切相关.通过光谱整形,使放大后的啁啾脉冲光的光谱分布为二阶超高斯分布.能够获得小于400 fs高信噪比的超短脉冲输出,此时所需种子啁啾脉冲能量仅为33μJ,带宽14 nm,在装置前级注入能力的范围之内.为百焦耳装置光谱整形实验的开展提供了理论指导.     

Multibeam Raman amplification of a finite-duration seed in a short distance

A new scheme of multibeam Raman amplification(MRA) is proposed in virtue of the collective mode by sharing a common scattered light. Multiple laser beams can provide a higher growth rate, but the overlapping region limits the amplification length. We suggest to use a finite-duration seed to facilitate MRA in a short distance. Through two-dimensional particle-in-cell simulations, we find that two-beam Raman amplification has a much higher growth rate than that of singlebeam one. This growth rate depends on the initial seed amplitude, electron temperature, and seed duration. An empirical criterion, γ_0τ_c = 1, where γ_0 is the theoretical growth rate of MRA, is used to choose a proper duration for a higher growth rate. After a total amplification length of 320 μm, the two-beam Raman amplification shows nonlinear features of pulse compression and a bow-shape wave front, indicating that the amplification has finally entered the self-similar regime.     

用于宽带啁啾脉冲光参量放大系统精确同步的新方法

基于非共线光参量放大,以波长800 nm飞秒激光的倍频光为抽运光,以激光二极管640 nm连续波激光为信号光,产生了与800 nm飞秒激光精确同步的无直流本底的1064 nm脉冲光。实验结果显示该1064 nm的光脉冲在脉冲能量和空间光束质量上均可作为1064 nm波长脉冲放大器的种子光。仅通过一级简单紧凑的非共线参量放大就可实现光周期量级的光参量啁啾脉冲放大系统的抽运激光和种子光的精确同步。     

与794nm飞秒激光精确同步的无直流背底的1064nm脉冲光的产生

基于非共线光参量放大(NOPA)，以宽带794nm飞秒激光的倍频光为抽运光，以连续的He-Ne激光为信号光，产生了与宽带794nm飞秒激光精确同步的无直流背底的1064nm的脉冲光.实验结果显示该1064nm的光脉冲可作为光参量啁啾脉冲放大系统的抽运激光链的种子光，从而实现用全光学方法实现OPCPA系统抽运光和信号光的精确同步.还将非共线光参量放大器置于经特殊设计的He-Ne激光腔内，也同样成功得到了无直流背底的1064nm的光脉冲.经一次光参量放大后所得到的1064nm光的光谱和空间啁啾特性与非共线光参量放大器置于He-Ne激光腔外时得到的1064nm的光脉冲相同，而其单脉冲能量约为腔外NOPA的10倍. 关键词： 非线性光参量放大 光参量啁啾脉冲放大 时间同步     

Multimillijoule chirped parametric amplification of few-cycle pulses

The concept of optical parametric chirped-pulse amplification is applied to attain pulses with energies up to 8 mJ and a bandwidth of more than 100 THz. Stretched broadband seed pulses from a Ti:sapphire oscillator are amplified in a multistage noncollinear type I phase-matched beta-barium borate parametric amplifier by use of an independent picosecond laser with lock-to-clock repetition rate synchronization. Partial compression of amplified pulses is demonstrated down to a 10-fs duration with a down-chirped pulse stretcher and a nearly lossless compressor comprising bulk material and positive-dispersion chirped mirrors.     

掺Er3+飞秒光纤放大器的特性研究

依据二能级速率方程和光传输方程,理论计算了Er3+光纤放大器中Er3+光纤的最佳长度Lc. 以全光纤飞秒激光器输出的孤子脉冲作为种子源,以理论值Lc作为实际采用的光纤长度,实验测量了Er3+光纤放大器在同向泵浦和反向泵浦下信号光的输出功率,得到同向泵浦的增益为20.0dB, 反向泵浦的增益为20.2 dB.同时测量了脉冲宽度随泵浦功率的变化,实验结果表明,随着泵浦功率的增大,输出光脉冲的宽度的压缩效应经历逐渐增强后逐渐减弱的过程.在同向泵浦方式下,可以得到更短的输出脉宽,其最短脉冲宽度为260 fs.     

High-peak-power femtosecond pulse compression with polarization-maintaining ytterbium-doped fiber amplification

We report the generation of 140 fs pulses with a peak power of up to 270 kW using a fiber pulse source based on a polarization-maintaining ytterbium-doped fiber amplifier and a semiconductor saturable absorber mirror mode-locked fiber laser seed. The seed laser pulses were amplified and chirped in the fiber amplifier and subsequently compressed in an external transmission grating pair. The use of a polarization-maintaining amplifier addresses nonlinear polarization-induced limitations to the obtainable compressed pulse duration and quality that can arise if isotropic fiber amplification is used. Numerical simulations of the system support the experimental measurements and also confirm the role of fiber dispersion in obtaining high-quality compressed pulses.     

Trends in ultrashort and ultrahigh power laser pulses based on optical parametric chirped pulse amplification

Since the proof-of-principle demonstration of optical parametric amplification to efficiently amplify chirped laser pulses in 1992,optical parametric chirped pulse amplification(OPCPA)became the most promising method for the amplification of broadband optical pulses.In the meantime,we are witnessing an exciting progress in the development of powerful and ultrashort pulse laser systems that employ chirped pulse parametric amplifiers.The output power and pulse duration of these systems have ranged from a few gigawatts to hundreds of terawatts with a potential of tens of petawatts power level.Meanwhile,the output pulse duration based on optical parametric amplification has entered the range of fewoptical-cycle field.In this paper,we overview the basic principles,trends in development,and current state of the ultrashort and laser systems based on OPCPA,respectively.     

基于光束偏转的扫描式宽带光参量啁啾脉冲放大

光参量啁啾脉冲放大(OPCPA)是超短激光脉冲领域的重要技术之一,增大增益带宽对提高OPCPA的转换效率、实现宽带光参量放大具有重要的意义.本文将光束偏转和非共线OPCPA有机结合,提出了基于光束偏转的扫描式宽带OPCPA模型.分析了通过光束偏转来时刻改变非共线角,以保证各频率成分的相位匹配,从而增大增益带宽的基本原理.采用提出的扫描式宽带OPCPA,针对800 nm中心波长、带宽约为100 nm信号光的光参量放大进行了数值计算.结果表明:经过扫描式OPCPA后,信号光的带宽与放大之前几乎相同,光谱没有窄化;扫描式OPCPA比固定非共线角方式的放大极大地增加了增益带宽和转换效率,实现了宽带的光参量放大;要满足信号光各频率成分的相位匹配,达到最大的增益带宽和转换效率,需要尽量减小加载到钽铌酸钾(KTa_(1-x) Nb_xO_3, KTN)电光晶体上的电压抖动和电压延时.     

A 61-mJ, 1-kHz cryogenic Yb: YAG laser amplifier

We report a diode-pumped rod-type Yb:YAG laser amplifier operating at 1 kHz. Cryogenic cooling method was adopted to make the Yb:YAG crystal work with four-level behavior. A single-frequency fiber laser acts as the seed in an actively Q-switched Yb:YAG oscillator. The resonator delivers 5.75-mJ pulses at 1 kHz with a pulse duration of approximately 40 ns. The pulses were amplified to 61 mJ in a four-pass rod-type Yb:YAG amplifier with optical-to-optical efficiency of 24% in the main amplifier. The M² parameter of the output laser is <1.4.     

超短激光脉冲调制上转换放大

在超短激光脉冲倍频过程中，由于调制不稳定性而产生多色圆锥辐射. 在多色圆锥辐射的任 意方向上同步注入一束宽带种子光，可以得到相应频率的调制上转换放大. 放大的光脉冲的 中心波长在500 nm时单脉冲能量最大可至150 μJ并且具有60 nm的频谱宽度. 通过改变种子 光的入射角度而实现上转换放大中心波长的连续调谐，范围约为290 nm. 关键词： 调制上转换放大 调制不稳定性 多色圆锥辐射     

100 W全光纤声光调Q光纤激光器实验研究

 报道了一台全光纤结构主振荡功率放大(MOPA)型掺镱脉冲光纤激光器,以光纤光栅为腔镜,光纤型声光调Q的光纤激光器为种子源,通过两级掺镱双包层光纤放大器实现功率放大。对声光调Q的光纤激光器输出特性进行了研究,比较了不同泵浦波长、不同重复频率对激光输出功率和脉冲宽度的影响,并实现了最短脉冲宽度25 ns、单脉冲能量45 μJ的脉冲激光输出。在重复频率50 kHz时,对脉冲宽度130 ns、平均功率0.6 W的种子光进行放大,得到了平均功率102.5 W、脉冲宽度约240 ns的激光输出。     

基于大基模体积的10mJ飞秒钛宝石激光再生放大器

文章报导了基于大基模体积的高能量飞秒钛宝石激光再生放大器的设计与实验研究,在重复频率10 Hz、抽运能量60 mJ的激励下,得到了单脉冲能量17.4 mJ的种子脉冲放大结果,压缩后的脉冲宽度为40.6 fs,能量为13.9 mJ.借助于此大基模体积再生腔,仅增加一级多通放大,实现了峰值功率达1.9 TW飞秒激光脉冲输出.结果表明,大模体积再生放大不仅降低了后续放大对抽运能量的要求,也可以单独压缩实现再生腔直接输出10 mJ量级的飞秒激光脉冲,是大能量高峰值功率飞秒激光系统的优质前端.     

锁模激光脉冲串放大过程中的整形控制

 为了获得具有特殊要求的驱动激光,设计了一套以Nd:YVO4锁模激光器为种子光,用二极管激光器泵浦的Nd:YAG放大系统进行放大的激光系统。对放大过程中锁模激光脉冲串因增益饱和造成的脉冲串包络畸变以及对包络的整形控制进行了研究。实验获得能量为24 mJ的基频光,5.7 mJ的倍频光,0.608 mJ的紫外四倍频光;通过脉冲串整形控制,实现了包络顶部平整的紫外超短脉冲串输出,满足了光阴极注入器对驱动激光的特殊需求。     

采用光谱展宽技术的钛宝石飞秒激光放大器

报道了飞秒激光啁啾脉冲放大器中的激光脉冲光谱展宽技术，实验中使用了几种光谱展宽元件，结果表明使用激光光谱展宽元件能有效地将飞秒激光脉冲 光谱展宽，抑制了飞秒激光放大器中常见的激光脉冲光谱增益窄化现象，从飞秒放大系统的振荡级输出28fs种子脉冲，放大后得到了重复频率为10Hz、峰值功率为1．6TW、脉冲宽度37．5fs的超短强飞秒激光脉冲 。