In situ detection of Bacillus anthracis spores using fully submersible, self-exciting, self-sensing PMN-PT/Sn piezoelectric microcantilevers

In this study, we have demonstrated in situ, all-electrical detection of Bacillus anthracis (BA) spores using lead magnesium niobate-lead titanate/tin (PMN-PT/Sn) piezoelectric microcantilever sensors (PEMS) fabricated from PMN-PT freestanding films and electrically insulated with methyltrimethoxysilane (MTMS) coatings on the tin surface. Antibody specific to BA spore surface antigen was immobilized on the platinum electrode of the PMN-PT layer. In phosphate-buffered saline (PBS) solution, the PMN-PT/Sn PEMS exhibited quality (Q) values ranging from 50 to 75. The detection was carried out in a closed-loop flow cell with a liquid volume of 0.8 ml and a flow rate of 1 ml min(-1). It was shown that one sensor, "PEMS-A" (500 microm long, 800 microm wide, with a 22 microm thick PMN-PT layer, a 20 microm thick tin layer and a 1 +/- 0.5 x 10(-12) g Hz(-1) mass detection sensitivity) exhibited resonance frequency shifts of 2100 +/- 200, 1100 +/- 100 and 700 +/- 100 Hz at concentrations of 20,000, 2000, and 200 spores ml(-1) or 16,000, 1600, and 160 total spores, respectively. Additionally, "PEMS-B" (350 microm long, 800 microm wide, with an 8 microm thick PMN-PT layer, a 6 microm thick tin layer and a 2 +/- 1 x 10(-13) g Hz(-1) mass detection sensitivity) exhibited resonance frequency shifts of 2400 +/- 200, 1500 +/- 200, 500 +/- 150 and 200 +/- 100 Hz at concentrations of 20,000, 2000, 100, and 45 spores ml(-1) or 16,000, 1600, 80, and 36 total spores, respectively.     

An antibody-sensitized microfabricated cantilever for the growth detection of Aspergillus niger spores.

We demonstrate a new sensitive biosensor for detection of vital fungal spores of Aspergillus niger. The biosensor is based on silicon microfabricated cantilever arrays operated in dynamic mode. The change in resonance frequency of the sensor is a function of mass binding to the cantilever surface. For specific A. niger spore immobilization on the cantilever, each cantilever was individually coated with anti-Aspergillus niger polyclonal antibodies. We demonstrate the detection of single A. niger spores and their subsequent growth on the functionalized cantilever surface by online measurements of resonance frequency shifts. The new biosensor operating in humid air allows quantitative and qualitative detection of A. niger spores as well as detection of vital, functional spores in situ within approximately 4 h. The detection limit of the sensor is 103 CFU mL-1. Mass sensitivity of the cantilever sensor is approximately 53 pg Hz-1.     

Detection of Bacillus subtilis spores using peptide-functionalized cantilever arrays

We move beyond antibody-antigen binding systems and demonstrate that short peptide ligands can be used to efficiently capture Bacillus subtilis (a simulant of Bacillus anthracis) spores in liquids. On an eight-cantilever array chip, four cantilevers were coated with binding peptide (NHFLPKV-GGGC) and the other four were coated with control peptide (LFNKHVP-GGGC) for reagentless detection of whole B. subtilis spores in liquids. The peptide-ligand-functionalized microcantilever chip was mounted onto a fluid cell filled with a B. subtilis spore suspension for approximately 40 min; a 40 nm net differential deflection was observed. Fifth-mode resonant frequency measurements were also performed before and after dipping microcantilever arrays into a static B. subtilis solution showing a substantial decrease in frequency for binding-peptide-coated microcantilevers as compared to that for control peptide cantilevers. Further confirmation was obtained by subsequent examination of the microcantilever arrays under a dark-field microscope. Applications of this technology will serve as a platform for the detection of pathogenic organisms including biowarfare agents.     

Development of a combined technique using a rapid one-step immunochromatographic assay and indirect competitive ELISA for the rapid detection of baicalin

A colloidal gold conjugated anti-baicalin monoclonal antibody (anti-BA MAb) was prepared and used in an immunochromatographic assay (ICA) for BA in Scutellariae Radix and Kampo medicines. This competitive ICA uses an anti-BA MAb which shows a high specificity for BA and baicalein. Its advantages include a short assay time (15 min), no dependence on any instrumental systems, and it can detect BA in plant materials and Kampo medicines. The limit of detection for the ICA was found to be around 0.6 μg mL⁻¹of baicalin. Moreover, the usefulness of the combination of indirect competitive ELISA and the ICA using anti-BA MAb as a quality control method was confirmed for analysis of BA in Scutellariae Radix and Kampo medicines with a sufficient sensitivity (200 ng mL⁻¹ to 2 μg mL⁻¹), obtainable in an easy and timely manner.     

Sporicidal testing of commercial germicides using a chemical standard and a calibrated bioindicator

The AOAC sporicidal method uses as a standard the resistance of spores on carriers to 2.5N HCl. This resistance is variable at exposure times ranging from 2 to 20 min. The method described in this paper uses a glutaraldehyde standard and distinguishes various levels of sporicidal activity in the presence of 1-5% glutaraldehyde by using appropriate spore strains, spore preparations, and spore levels. The resistances of 2 Bacillus subtilis 19659 spore preparations cultured in 10% Columbia broth plus manganese and nutrient agar plus minerals, as well as that of B. subtilis var. niger cultured on Lab-Lemco agar, were tested. T-soy broth was a better recovery medium than fluid thioglycollate or modified fluid thioglycollate for B. subtilis 19659 spores exposed to HCl. Sporicidal tests were done on B. subtilis 19659 spores with 2 types of spore preparations. A commercial glutaraldehyde germicide was used for comparison of the sporicidal activity of the glutaraldehyde standard. Two strains of B. subtilis spores and 4 levels of spores (20,000-80,000, 100,000-400,000, 500,000-800,000, and 1,000,000 and up) were removed from check penicylinders from the same batches used for sporicidal tests. B. subtilis var. niger spores were the most resistant to HCl, while B. subtilis 19659 spores were more resistant to glutaraldehyde. Sporicidal activities of a commercial germicide containing 2.5% glutaraldehyde with additives and another containing 5% glutaraldehyde in phosphate buffer were similar. Both totally destroyed high levels of B. subtilis 19659 spores cultured in 10% Columbia broth plus manganese. Results indicate that use of a glutaraldehyde standard, calibrated numbers of spores on penicylinders (bioindicators), and appropriate spore strains and preparations can reduce the variability of sporicidal testing of commercial germicides.     

Recovery and sporicidal resistance of various B. subtilis spore preparations on porcelain penicylinders compared with results from AOAC test methods

Sporicidal test results obtained from carriers inoculated with 4 types of defined Bacillus subtilis spore preparations were compared with the standard AOAC sporicidal test using soil extract nutrient broth (SENB) B. subtilis 19659 spores. Recoveries of spores inoculated on penicylinders from B. subtilis clean spores (washed and suspended in water) and B. subtilis 19659 spores inoculated from culture filtrates according to the AOAC method were compared. Spores were exposed to 6 concentrations (0.5-3.0% w/v) of glutaraldehyde in phosphate buffer (pH 7.5) for 10 h. Concentrations were established by titrimetry and liquid chromatography. Recoveries of surviving spores were determined for 3 types of clean B. subtilis var. niger preparations, one clean B. subtilis 19659 preparation, and the SENB B. subtilis 19659 filtrates. Spore carriers, inoculated by the standard AOAC protocol, resulted in as much as a 2-log number difference in runs 1-12, but not more than 0.5 log number for each clean spore preparation. The SENB spores varied most in resistance to glutaraldehyde, with no growth in recovery media from 3 different batches of 1, 1.5, and 2% glutaraldehyde. Separate batches of SENB preparations of B. subtilis 19659 were resistant and destroyed by 1.0% glutaraldehyde, with 3.98 and 6.0 log numbers of spores on penicylinders, respectively. Clean spore preparations of B. subtilis 19659 on porcelain penicylinders were more resistant to glutaraldehyde than were SENB spores. Nutrient agar/Mg/Ca and nutrient agar/Mg spore preparations of B. subtilis var. niger showed the most uniform resistance to glutaraldehyde. Spores with calcium added showed increased resistance to glutaraldehyde. B. subtilis 19659 spores from the Columbia broth spore preparation were the most resistant and were recovered after exposure to 3.0% glutaraldehyde.     

Biosensor for the specific detection of a single viable B. anthracis spore

A simple membrane strip-based biosensor for the detection of viable B. anthracis spores was developed and combined with a spore germination procedure as well as a nucleic acid amplification reaction to identify as little as one viable B. anthracis spore in less than 12 h. The biosensor is based on identification of a unique mRNA sequence from the anthrax toxin activator (atxA) gene encoded on the toxin plasmid, pXO1. Preliminary work relied on plasmid vectors in both E. coli and B. thuringiensis expressing the atxA gene. Once the principle was firmly established, the vaccine strain of B. anthracis was used. After inducing germination and outgrowth of spores of B. anthracis (Sterne strain), RNA was extracted from lysed cells, amplified using nucleic acid sequence-based amplification (NASBA), and rapidly identified by the biosensor. While the biosensor assay requires only 15-min assay time, the overall process takes 12 h for the detection of as little as one viable B. anthracis spore, and is shortened significantly, if larger amounts of spores are present. The biosensor is based on an oligonucleotide sandwich-hybridization assay format. It uses a membrane flow-through system with an immobilized oligonucleotide probe that hybridizes with the target sequence. Signal amplification is provided when the target sequence hybridizes to a second oligonucleotide probe that has been coupled to dye-encapsulating liposomes. The dye in the liposomes then provides a signal that can be read visually or quantified with a hand-held reflectometer. The biosensor can detect as little as 1.5 fmol of target mRNA. Specificity analysis revealed no crossreactivity with closely related species such as B. cereus, B. megaterium, B. subtilis, B. thuringiensis etc.     

Architecture and high-resolution structure of Bacillus thuringiensis and Bacillus cereus spore coat surfaces

We have utilized atomic force microscopy (AFM) to visualize the native surface topography and ultrastructure of Bacillus thuringiensis and Bacillus cereus spores in water and in air. AFM was able to resolve the nanostructure of the exosporium and three distinctive classes of appendages. Removal of the exosporium exposed either a hexagonal honeycomb layer (B. thuringiensis) or a rodlet outer spore coat layer (B. cereus). Removal of the rodlet structure from B. cereus spores revealed an underlying honeycomb layer similar to that observed with B. thuringiensis spores. The periodicity of the rodlet structure on the outer spore coat of B. cereus was approximately 8 nm, and the length of the rodlets was limited to the cross-patched domain structure of this layer to approximately 200 nm. The lattice constant of the honeycomb structures was approximately 9 nm for both B. cereus and B. thuringiensis spores. Both honeycomb structures were composed of multiple, disoriented domains with distinct boundaries. Our results demonstrate that variations in storage and preparation procedures result in architectural changes in individual spore surfaces, which establish AFM as a useful tool for evaluation of preparation and processing "fingerprints" of bacterial spores. These results establish that high-resolution AFM has the capacity to reveal species-specific assembly and nanometer scale structure of spore surfaces. These species-specific spore surface structural variations are correlated with sequence divergences in a spore core structural protein SspE.     

Physicochemical characterization of natural ionic Microreservoirs: Bacillus subtilis dormant spores

The kinetics of proton exchange between dormant spores and aqueous environment was examined by time-resolved micropotentiometry, the method we recently introduced for hydrogel particles of micro- and nanometer diameter (J. Phys. Chem. B 2006, 110, 15107). In this work, the method was applied to the suspensions of dormant Bacillus subtilis spore of different concentrations to show that proton uptake kinetics was a multistep process involving a number of successively approximately 10-fold slower steps of proton penetration into the bulk and their binding to the ionizable groups within different layers of a spore structure. By analyzing the proton equilibrium binding to ionizable groups inside a spore, it was shown that each Bacillus subtilis spore behaves like almost infinite ionic reservoir capable of accumulating billions of protons (N approximately 2 x 10(10) per spore). The obtained pK(a) value of 4.7 for the spores studied is the first quantitative indication on carboxyl groups as the major ionizable groups fixed in a spore matrix. In general, proton equilibrium binding within the spore matrix obeys the fundamental law of the Langmuir isotherm. The proton binding to the ionizable groups slows down the free proton diffusion within a spore, but this effect is substantially weakened by increasing the initial concentration of protons added. On the basis of the diffusion time analysis, it was found that the effective diffusion coefficient for hydrogen ions within the spore core can be up to 3 orders of magnitude lower than that within the coats and cortex. We speculate that the spore inner membrane which separates core from cortex and coats in a dormant spore is a major permeability barrier for protons to penetrate into a lockbox of the genetic information (core).     

Immunoassay for B. globigii spores as a model for detecting B. anthracis spores in finished water

The 2001 anthrax alarm in the US raised concerns about the Nation's preparedness to the threat of bioterrorism, and the demand for early warning systems that might be used in the case of a biological attack continues to grow. Here we develop an ultra-sensitive rapid detection method for B. globigii(BG) spores, the simulant of B. anthracis(BA) spores. BG spores were detected by a bead-based sandwich immunoassay with fluorescence detection. Paramagnetic Dynal beads were used as a solid support, primary antibody was attached to the beads by streptavidin-biotin coupling and the secondary antibody had an alkaline phosphatase (AP) enzyme label. Enzymatic conversion of fluorescein diphosphate (FDP) to fluorescein by AP was measured in real time with lambda(ex)= 490 nm and lambda(em)= 520 nm. The assay was linear from 2.6 x 10(3)-5.6 x 10(5) BG spores mL(-1), and the detection limit was 2.6 x 10(3) spores mL(-1) or 78 spores. All reagent concentrations and incubation times were optimized. The assay time from the moment the spores were introduced to the system was 30 min, and real-time fluorescence detection was done in less than 1 min. Formation of the BG spores-capture beads complex was confirmed by environmental scanning electron microscopy (ESEM). BG spores were detected successfully when doped into Cincinnati tap water to demonstrate the applicability of the developed method to detect the spores in non-buffered media.     

Analysis of Bacillus globigii spores by CE

It is imperative in today's world that harmful airborne or solution-based microbes can be detected quickly and efficiently. Bacillus globigii (Bg) spores are used as a simulant for Bacillus anthracis (Ba) due to their similar shape, size, and cellular makeup. The utility of CE to separate and detect low levels of Bg spore concentrations will be evaluated. To differentiate spores from background particulates, several dyes, including fluorescamine, C-10, NN-127, Red-1c, and indocyanine green (ICG), were utilized as noncovalent labels for proteins on the Bg spore surface, as well as for HSA and homoserine standards. On-column labeling, with dye present in the running buffer, was utilized to obtain greater sensitivity and better separation. CE with LIF detection enables interactions between the dye and spore surface proteins to be observed, with enhanced fluorescence occurring upon binding of the dye to surface protein. Resulting electropherograms showed unique fingerprints for each dye with Bg spores. Migration times were under 10 min for all dye-spore complexes, with net mobilities ranging from 3.5x10(-4) to 6.9x10(-4) cm(2) V(-1) s(-1), and calibration curves yielded correlation coefficients of 0.98 or better for four of the dyes studied.     

Effects of the binding of alpha/beta-type small, acid-soluble spore proteins on the photochemistry of DNA in spores of Bacillus subtilis and in vitro

The main lesion produced in DNA by UV-C irradiation of spores of Bacillus subtilis is 5-thyminyl-5,6-dihydrothymine (spore photoproduct [SP]). In contrast, cyclobutane pyrimidine dimers (CPD) and pyrimidine (6-4) pyrimidone photoproducts (6-4PP) are the main photolesions in other cell types. The novel photochemistry of spore DNA is accounted for in part by its reduced hydration, but largely by the saturation of spore DNA with alpha/beta-type small, acid-soluble spore proteins (SASP). Using high-performance liquid chromatography-mass spectrometry analysis of the photoproducts, we showed that in wild-type B. subtilis spores (1) UV-C irradiation generates almost exclusively SP with little if any CPD and 6-4PP; (2) the SP generated is approximately 99% of the intrastrand derivative, but approximately 1% is in the interstrand form; and (3) there is no detectable formation of the SP analog between adjacent C and T residues. UV-C irradiation of spores lacking the majority of their alpha/beta-type SASP gave less SP than with wild-type spores and significant levels of CPD and 6-4PP. The binding of an alpha/beta-type SASP to isolated DNA either in dry films or in aqueous solution led to a large decrease in the yield of CPD and 6-4PP, and a concomitant increase in the yield of SP, although levels of interstrand photoproducts were extremely low.     

Real-time immunoassay of antibody activity in serum by surface plasmon resonance biosensor

A surface plasmon resonance biosensor has been used to determine antibody activity in serum. As a model system, the interaction of mouse IgG and sheep anti-mouse IgG polyclonal antibody was investigated in real time. The factors, including pH value, ionic strength, protein concentration, influencing electrostatic adsorption of mouse IgG protein onto carboxylated dextran-coated sensor chip surface, were studied. The procedures of mouse IgG protein immobilization and immune reaction were monitored in real time. The regeneration effect using the different elution reagents was also investigated. The same mouse IgG immobilized surface can be used for 100 cycles of binding and elution with only 0.38% loss per regeneration in reactivity. The results show that the surface plasmon resonance biosensor is a rapid, simple, sensitive, accurate and reliable detection technique for real-time immunoassay of antibody activity. The assay allows antibodies to be detected and studied in their native form without any purification.     

Diphenol miscibility effect on the immiscible polyester/polyether binary blends through intermolecular hydrogen‐bonding interaction

Miscibility and hydrogen bonding interaction have been investigated for the binary blends of poly(butylene adipate‐co‐44 mol % butylene terephthalate)[P(BA‐co‐BT)] with 4,4'‐thiodiphenol (TDP) and poly(ethylene‐ oxide)(PEO) with TDP; and the ternary blends of P(BA‐co‐BT)/PEO/TDP by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The DSC results indicated that the binary blends of P(BA‐co‐BT)/TDP and PEO/TDP were miscible because each blend showed only one composition‐dependent glass‐transition over the entire range of the blend composition. The formation of intermolecular hydrogen bonds between the hydroxyl groups of TDP and the carbonyl groups of P(BA‐co‐BT), and between the hydroxyl groups of TDP and the ether groups of PEO was confirmed by the FTIR spectra. According to the glass‐transition temperature measured by DSC, P(BA‐co‐BT) and PEO, their binary blends were immiscible over the entire range of blend composition, however, the miscibility between P(BA‐co‐BT) and PEO was enhanced through the TDP‐mediated intermolecular hydrogen bonding interaction. It was concluded that TDP content of about 5–10% may possibily enhance miscibility between P(BA‐co‐BT) and PEO via a hydrogen bonding interaction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2971–2982, 2004     

Preparation and evaluation of spore-specific affinity-augmented bio-imprinted beads

A novel, affinity-augmented, bacterial spore-imprinted, bead material was synthesized, based on a procedure developed for vegetative bacteria. The imprinted beads were intended as a front-end spore capture/concentration stage of an integrated biological detection system. Our approach involved embedding bead surfaces with Bacillus thuringiensis kurstaki (Bt) spores (as a surrogate for Bacillus anthracis) during synthesis. Subsequent steps involved lithographic deactivation using a perfluoroether; spore removal to create imprint sites; and coating imprints with the lectin, concanavalin A, to provide general affinity. The synthesis of the intended material with the desired imprints was verified by scanning electron and confocal laser-scanning microscopy. The material was evaluated using spore-binding assays with either Bt or Bacillus subtilis (Bs) spores. The binding assays indicated strong spore-binding capability and a robust imprinting effect that accounted for 25% additional binding over non-imprinted controls. The binding assay results also indicated that further refinement of the surface deactivation procedure would enhance the performance of the imprinted substrate.     

A rapid biosensor for viable <Emphasis Type="Italic">B. anthracis</Emphasis> spores

A simple membrane-strip-based biosensor assay has been combined with a nucleic acid sequence-based amplification (NASBA) reaction for rapid (4 h) detection of a small number (ten) of viable B. anthracis spores. The biosensor is based on identification of a unique mRNA sequence from one of the anthrax toxin genes, the protective antigen (pag), encoded on the toxin plasmid, pXO1, and thus provides high specificity toward B. anthracis. Previously, the anthrax toxins activator (atxA) mRNA had been used in our laboratory for the development of a biosensor for the detection of a single B. anthracis spore within 12 h. Changing the target sequence to the pag mRNA provided the ability to shorten the overall assay time significantly. The vaccine strain of B. anthracis (Sterne strain) was used in all experiments. A 500-L sample containing as few as ten spores was mixed with 500 L growth medium and incubated for 30 min for spore germination and mRNA production. Thus, only spores that are viable were detected. Subsequently, RNA was extracted from lysed cells, selectively amplified using NASBA, and rapidly identified by the biosensor. While the biosensor assay requires only 15 min assay time, the overall process takes 4 h for detection of ten viable B. anthracis spores, and is shortened significantly if more spores are present. The biosensor is based on an oligonucleotide sandwich-hybridization assay format. It uses a membrane flow-through system with an immobilized DNA probe that hybridizes with the target sequence. Signal amplification is provided when the target sequence hybridizes to a second DNA probe that has been coupled to liposomes encapsulating the dye sulforhodamine B. The amount of liposomes captured in the detection zone can be read visually or quantified with a hand-held reflectometer. The biosensor can detect as little as 1 fmol target mRNA (1 nmol L^–1). Specificity analysis revealed no cross-reactivity with 11 organisms tested, among them closely related species such as B. cereus, B. megaterium, B. subtilis, B. thuringiensis, Lactococcus lactis, Lactobacillus plantarum, and Chlostridium butyricum. Also, no false positive signals were obtained from nonviable spores. We suggest that this inexpensive biosensor is a viable option for rapid, on-site analysis providing highly specific data on the presence of viable B. anthracis spores.     

Rapid detection of an anthrax biomarker by surface-enhanced Raman spectroscopy

A rapid detection protocol suitable for use by first-responders to detect anthrax spores using a low-cost, battery-powered, portable Raman spectrometer has been developed. Bacillus subtilis spores, harmless simulants for Bacillus anthracis, were studied using surface-enhanced Raman spectroscopy (SERS) on silver film over nanosphere (AgFON) substrates. Calcium dipicolinate (CaDPA), a biomarker for bacillus spores, was efficiently extracted by sonication in nitric acid and rapidly detected by SERS. AgFON surfaces optimized for 750 nm laser excitation have been fabricated and characterized by UV-vis diffuse reflectance spectroscopy and SERS. The SERS signal from extracted CaDPA was measured over the spore concentration range of 10(-14)-10(-12) M to determine the saturation binding capacity of the AgFON surface and to calculate the adsorption constant (Kspore=1.7 x 10(13) M(-1)). At present, an 11 min procedure is capable of achieving a limit of detection (LOD) of approximately 2.6 x 10(3) spores, below the anthrax infectious dose of 10(4) spores. The data presented herein also demonstrate that the shelf life of prefabricated AgFON substrates can be as long as 40 days prior to use. Finally, these sensing capabilities have been successfully transitioned from a laboratory spectrometer to a field-portable instrument. Using this technology, 10(4) bacillus spores were detected with a 5 s data acquisition period on a 1 month old AgFON substrate. The speed and sensitivity of this SERS sensor indicate that this technology can be used as a viable option for the field analysis of potentially harmful environmental samples.     

Specific peptides as alternative to antibody ligands for biomagnetic separation of Clostridium tyrobutyricum spores

Nowadays, the reference method for the detection of Clostridium tyrobutyricum in milk is the most-probable-number method, a very time-consuming and non-specific method. In this work, the suitability of the use of superparamagnetic beads coated with specific antibodies and peptides for bioseparation and concentration of spores of C. tyrobutyricum has been assessed. Peptide or antibody functionalized nanoparticles were able to specifically bind C. tyrobutyricum spores and concentrate them up to detectable levels. Moreover, several factors, such as particle size (200 nm and 1 μm), particle derivatization (aminated and carboxylated beads), coating method, and type of ligand have been studied in order to establish the most appropriate conditions for spore separation. Results show that concentration of spore is favored by a smaller bead size due to the wider surface of interaction in relation to particle volume. Antibody orientation, related to the binding method, is also critical in spore recovery. However, specific peptides seem to be a better ligand than antibodies, not only due to the higher recovery ratio of spores obtained but also due to the prolonged stability over time, allowing an optimal recovery of spores up to 3 weeks after bead coating. These results demonstrate that specific peptides bound to magnetic nanoparticles can be used instead of traditional antibodies to specifically bind C. tyrobutyricum spores being a potential basis for a rapid method to detect this bacterial target.     

Determination of minor proteins of bovine milk and colostrum by optical biosensor analysis

Automated, rapid, sensitive, and label-free biosensor-based immunoassays for immunoglobulin G (IgG), folate binding protein, lactoferrin, and lactoperoxidase in bovine milk using surface plasmon resonance optical detection with direct binding assay format are described. Samples are prepared for analysis by direct dilution into buffer. Analysis conditions, including ligand immobilization, flow rate, contact time, and regeneration are defined and nonspecific binding considerations evaluated. The technique has been applied to the measurement of these proteins in consumer milks, colostrum, milk products, and infant formulas, and their temporal change during early bovine lactation followed.     

紫外光度法间接测定脱脂乳中的芽孢数量

为了有效控制乳制品生产过程、保证质量,克服芽孢杆菌传统计数方法周期长的缺点,本实验通过分光光度法检测芽孢中特异性物质2,6-吡啶二羧酸(DPA)。根据DPA浓度与芽孢数量的关系,建立了快速检测脱脂乳中芽孢数量的方法。本研究对脱脂乳及其芽孢处理、DPA释放及采用紫外分光光度法检测做了研究。通过准确度和加标回收率检验,建立DPA含量与芽孢数的线性关系,回归方程为y=0.2084x-0.9363,r=0.6998,经验证可有效估测脱脂乳中芽孢数量(P<0.05)。