Mercury determination and speciation analysis in surface waters

A sorbent L-cysteine grafted silica gel has been evaluated for separation and enrichment of dissolved inorganic i-Hg(II) and methylmercury CH₃Hg(I) from surface waters at sub-μg L⁻¹ concentrations. Chemical parameters for mercury species enrichment and separation have been optimized. Analytical schemes for the determination of Hg species, using selective column solid phase extraction (SPE) with continuous flow chemical vapor generation atomic absorption spectrometry (CF-CVG-AAS) or inductively coupled plasma-mass spectrometry (ICP-MS) were developed. Possibilities for on-site SPE enrichment were demonstrated as well. The limits of quantification were 1.5 and 5 ng L⁻¹ for dissolved i-Hg(II) and CH₃Hg(I) by CF-CVG-AAS and 1 and 2.5 ng L⁻¹ by ICP-MS with relative standard deviations between 7–12% and 7–14%, respectively. The chemically modified SPE sorbent has demonstrated high regeneration ability, chemical and mechanical stability, acceptable capacity and good enrichment factors. Results for total dissolved mercury were in reasonable agreement with those from independent analyses by direct ICP-MS determinations for river waters and for estuarine water certified reference material.      

In vitro translation with [<Superscript>34</Superscript>S]-labeled methionine,selenomethionine, and telluromethionine

Heteroisotope and heteroatom tagging with [³⁴S]-enriched methionine (Met), selenomethionine (SeMet), and telluromethionine (TeMet) was applied to in vitro translation. Green fluorescent protein (GFP) and JNK stimulatory phosphatase-1 (JSP-1) genes were translated with wheat germ extract (WGE) in the presence of Met derivatives. GFPs containing Met derivatives were subjected to HPLC coupled with treble detection, i.e., a photodiode array detector, a fluorescence detector, and an inductively coupled plasma mass spectrometer (ICP-MS). The activities of JSP-1-containing Met derivatives were also measured. GFP and JSP-1 containing [³⁴S]-Met and SeMet showed comparable fluorescence intensities and enzyme activities to those containing naturally occurring Met. TeMet was unstable and decomposed in WGE, whereas SeMet was stable throughout the experimental period. Thus, although Te was the most sensitive to ICP-MS detection among S, Se, and Te, TeMet was less incorporated into the proteins than Met and SeMet. Finally, the potential of heteroisotope and heteroatom tagging of desired proteins in in vitro translation followed by ICP-MS detection was discussed. Figure TeMet was less incorporated into GFP than Met and SeMet due to its instability in WGE     

Dye removal,antibacterial properties,and morphological behavior of hydroxyapatite doped with Pd ions

Hydroxyapatite (HAP) containing different contents of palladium (Pd) ions were synthesized using the co-precipitation method. The structural and morphological properties of the as-synthesized compositions were investigated using XRD and FESEM. The c/a increased from 0.728 to 0.733 with the lowest and highest contributions of Pd(II), respectively. Furthermore, the morphological features were investigated using FESEM. It was illustrated that Pd-HAP was formed as agglomerated as rod shapes with dimensions in the range of 63.4–110.3 nm for no Pd additions, and the size was reduced reaching 43.4–70.5 nm for the highest Pd contribution. Besides, the maximum height of the roughness (R_t) grew from 183.6 up to 236.5 nm for the lowest and highest Pd(II). Besides, the obtained specific surface area was around 28.3, 42.0, and 63.4 m²/g for 0.0Pd-HAP, 0.6Pd-HAP, and 1.0Pd-HAP, respectively. The antibacterial activity was examined against both Escherichia coli (E-coli) and Staphylococcus aureus (S. aureus), and it obvious that the activity was enhanced upon Pd content. The inhibition zone was increased from no sensitivity reaching 4.3 ± 0.9 and 4.5 ± 0.8 mm for no Pd and the highest one, respectively. The removal efficiency of dyes was examined for methylene blue (MB) and it was shown that after 120 min of irradiation, the removal efficiency reached around 86.4% for the highest contribution of Pd. The pseudo-first-order constant (K_app) increased from 0.0032 to 0.0179 min⁻¹. The recyclability of Pd-HAP denoted that removal efficiency decreased to 5.65, 8.14, 6.24, 8.76, and 10.2% for different contents of Pd(II) after 6 cycles.     

Development of an accurate,sensitive, and robust isotope dilution laser ablation ICP-MS method for simultaneous multi-element analysis (chlorine,sulfur, and heavy metals) in coal samples

A method for the direct multi-element determination of Cl, S, Hg, Pb, Cd, U, Br, Cr, Cu, Fe, and Zn in powdered coal samples has been developed by applying inductively coupled plasma isotope dilution mass spectrometry (ICP-IDMS) with laser-assisted introduction into the plasma. A sector-field ICP-MS with a mass resolution of 4,000 and a high-ablation rate laser ablation system provided significantly better sensitivity, detection limits, and accuracy compared to a conventional laser ablation system coupled with a quadrupole ICP-MS. The sensitivity ranges from about 590 cps for ³⁵Cl⁺ to more than 6 × 10⁵ cps for ²³⁸U⁺ for 1 μg of trace element per gram of coal sample. Detection limits vary from 450 ng g⁻¹ for chlorine and 18 ng g⁻¹ for sulfur to 9.5 pg g⁻¹ for mercury and 0.3 pg g⁻¹ for uranium. Analyses of minor and trace elements in four certified reference materials (BCR-180 Gas Coal, BCR-331 Steam Coal, SRM 1632c Trace Elements in Coal, SRM 1635 Trace Elements in Coal) yielded good agreement of usually not more than 5% deviation from the certified values and precisions of less than 10% relative standard deviation for most elements. Higher relative standard deviations were found for particular elements such as Hg and Cd caused by inhomogeneities due to associations of these elements within micro-inclusions in coal which was demonstrated for Hg in SRM 1635, SRM 1632c, and another standard reference material (SRM 2682b, Sulfur and Mercury in Coal). The developed LA-ICP-IDMS method with its simple sample pretreatment opens the possibility for accurate, fast, and highly sensitive determinations of environmentally critical contaminants in coal as well as of trace impurities in similar sample materials like graphite powder and activated charcoal on a routine basis. Figure LA-ICP-IDMS allows direct multi-element determination in powdered coal samples     

Minimization of mass interferences in quadrupole inductively coupled plasma mass spectrometric (ICP-MS) determination of palladium using a flow injection on-line displacement solid-phase extraction protocol

A flow injection on-line displacement solid-phase extraction protocol was employed to minimize mass interferences with determination of palladium by inductively coupled plasma mass spectrometry (ICP-MS). The developed method involved in on-line complexing of Ag⁺ with pyrrolidine dithiocarbamate (PDC), presorption of the resultant Ag–PDC onto a microcolumn packed with the cigarette filter, displacement sorption of Pd²⁺ through loading the sample solution onto the microcolumn due to on-line displacement reaction between Pd²⁺ and the presorbed Ag–PDC, elution of the retained Pd²⁺ with 50 μL of ethanol for on-line ICP-MS detection. Interferences from co-existing heavy metal ions with lower stability of their PDC complexes relative to Ag–PDC were minimized/eliminated. No interferences from 5 mg L^− 1 Zn and 3 mg L^− 1 Pb for ¹⁰⁴Pd, 0.4 mg L^− 1 Cu for ¹⁰⁵Pd, 6 mg L^− 1 Zn and 2 mg L^− 1 Cd for ¹⁰⁶Pd, 6 mg L^− 1 Zn and 3 mg L^− 1 Cd for ¹⁰⁸Pd, and 2 mg L^− 1 Cd for ¹¹⁰Pd were observed for the determination of 100 ng L^− 1 Pd. The enhancement factors of 71–75, sample throughput of 23 samples h^− 1 and detection limits of 2.8–3.5 ng L^− 1 were achieved with the consumption of 3.0 mL of sample solution. The precision (RSD) for eleven replicate determinations of Pd at the 100 ng L^− 1 level was 1.8–2.7%. The developed method was applied to the determination of palladium in rock samples.     

Study of the chemical composition of particulate matter from the Rio de Janeiro metropolitan region,Brazil, by inductively coupled plasma-mass spectrometry and optical emission spectrometry

Air quality in the metropolitan region of Rio de Janeiro was evaluated by analysis of particulate matter (PM) in industrial (Santa Cruz) and rural (Seropédica) areas. Total suspended particles (TSP) and fine particulate matter (PM_2.5) collected in filters over 24 h were quantified and their chemical composition determined. TSP exceeded Brazilian guidelines (80 μg m^− 3) in Santa Cruz, while PM_2.5 levels exceeded the World Health Organization guidelines (10 μg m^− 3) in both locations. Filters were extracted with water and/or HNO₃, and the concentrations of 20 elements, mostly metals, were determined by inductively coupled plasma mass spectrometry (ICP-MS) and optical emission spectrometry (ICP OES). Water soluble inorganic anions were determined by ion chromatography (IC). To estimate the proportion of these elements extracted, a certified reference material (NIST SRM 1648a, Urban Dust) was subjected to the same extraction process. Concordant results were obtained by ICP-MS and ICP OES for most elements. Some elements could not be quantified by both techniques; the most appropriate technique was chosen in each case. The urban dust was also analyzed by the United States Environmental Protection Agency (US EPA) method, which employs a combination of hydrochloric and nitric acids for the extraction, but higher extraction efficiency was obtained when only nitric acid was employed. The US EPA method gave better results only for Sb. In the PM samples, the elements found in the highest average concentrations by ICP were Zn and Al (3–6 μg m^− 3). The anions found in the highest average concentrations were SO₄^2 − in PM_2.5 (2–4 μg m^− 3) and Cl⁻ in TSP (2–6 μg m^− 3). Principal component analysis (PCA) in combination with enrichment factors (EF) indicated industrial sources in PM_2.5. Analysis of TSP suggested both anthropogenic and natural sources. In conclusion, this work contributes data on air quality, as well as a method for the analysis of PM samples by ICP-MS.     

Microwave-assisted solid phase extraction prior to ICP-MS determination of Pd and Pt in environmental and biological samples

A sensitive and selective microwave-assisted solid phase extraction procedure coupled to inductively coupled plasma-mass spectrometry (ICP-MS) is proposed for palladium (Pd) and platinum (Pt) quantification in environmental and biological samples. Pd and Pt were quantitatively retained on commercial thioureido propyl functionalised silica gel packed inside a home-made glass microcolumn, and later eluted with 0.5% thiourea solution under microwave irradiation, followed by ICP-MS determination. The main variables affecting the procedural stages (i.e., sorption and desorption) and ICP-MS determination were optimised. The best conditions found were: (a) sorption: sample acidity, 1?M HCl; sample flow rate, 3?mL?min^?1; (b) desorption: microwave radiation, power 800?W; eluent concentration, 0.5% thiourea; eluent flow rate, 0.5?mL?min^?1; (c) ICP-MS determination: nebuliser feeding, free aspiration (0.3?mL?min^?1); internal standard, Rh (5?µg?L^?1). Analyte recoveries were higher than 90% and concentration factors up to 90 and 92 were achieved for Pd and Pt, respectively. Depending on the conditions, the methodological limits of detection were down to 0.2?ng?L^?1 for both analytes and repeatability, expressed as RSD%, varied between 1.3 and 11.0%. A method selectivity evaluation showed that most of the ICP-MS interferents were either quantitatively separated or more than 86% eliminated, except for Cu (elimination efficiency around 30%). Finally, the method was successfully used to determine Pd in certified reference materials (i.e. human urine and serum) and Pd and Pt in PM₁₀ airborne particulate matter fractions.     

Stability of arsenic peptides in plant extracts: off-line versus on-line parallel elemental and molecular mass spectrometric detection for liquid chromatographic separation

The instability of metal and metalloid complexes during analytical processes has always been an issue of an uncertainty regarding their speciation in plant extracts. Two different speciation protocols were compared regarding the analysis of arsenic phytochelatin (As^IIIPC) complexes in fresh plant material. As the final step for separation/detection both methods used RP-HPLC simultaneously coupled to ICP-MS and ES-MS. However, one method was the often used off-line approach using two-dimensional separation, i.e. a pre-cleaning step using size-exclusion chromatography with subsequent fraction collection and freeze-drying prior to the analysis using RP-HPLC–ICP-MS and/or ES-MS. This approach revealed that less than 2% of the total arsenic was bound to peptides such as phytochelatins in the root extract of an arsenate exposed Thunbergia alata, whereas the direct on-line method showed that 83% of arsenic was bound to peptides, mainly as As^IIIPC₃ and (GS)As^IIIPC₂. Key analytical factors were identified which destabilise the As^IIIPCs. The low pH of the mobile phase (0.1% formic acid) using RP-HPLC–ICP-MS/ES-MS stabilises the arsenic peptide complexes in the plant extract as well as the free peptide concentration, as shown by the kinetic disintegration study of the model compound As^III(GS)₃ at pH 2.2 and 3.8. But only short half-lives of only a few hours were determined for the arsenic glutathione complex. Although As^IIIPC₃ showed a ten times higher half-life (23 h) in a plant extract, the pre-cleaning step with subsequent fractionation in a mobile phase of pH 5.6 contributes to the destabilisation of the arsenic peptides in the off-line method. Furthermore, it was found that during a freeze-drying process more than 90% of an As^IIIPC₃ complex and smaller free peptides such as PC₂ and PC₃ can be lost. Although the two-dimensional off-line method has been used successfully for other metal complexes, it is concluded here that the fractionation and the subsequent freeze-drying were responsible for the loss of arsenic phytochelatin complexes during the analysis. Hence, the on-line HPLC–ICP-MS/ES-MS is the preferred method for such unstable peptide complexes. Since freeze-drying has been found to be undesirable for sample storage other methods for sample handling needed to be investigated. Hence, the storage of the fresh plant at low temperature was tested. We can report for the first time a storage method which successfully conserves the integrity of the labile arsenic phytochelatin complexes: quantitative recovery of As^IIIPC₃ in a formic acid extract of a Thunbergia alata exposed for 24 h to 1 mg As^v L⁻¹ was found when the fresh plant was stored for 21 days at 193 K. Figure On-line HPLC–ICP-MS/ES-MS (bottom) is the preferred method for MS determination of unstable arsenic peptide complexes in plant extracts, since this avoids fractionation and subsequent freeze-drying that are responsible for loss of arsenic phytochelatin complexes in the 2D off-line method (top) Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Multivariate optimization and simultaneous determination of hydride and non-hydride-forming elements in samples of a wide pH range using dual-mode sample introduction with plasma techniques: application on leachates from cement mortar material

Analytical methods have been developed for the simultaneous determination of hydride-forming (As, Sb) and non-hydride-forming (Cr, Mo, V) elements in aqueous samples of a wide pH range (pH 3–13). The methods used dual-mode (DM) sample introduction with ICP-AES and ICP-MS instruments. The effect of selected experimental variables, i.e., sample pH and concentrations of HNO₃, thiourea, and NaBH₄, were studied in a multivariate way using face-centered central composite design (FC-CCD). Compromised optimum values of the experimental parameters were identified using a response optimizer. The statistically found optimum values were verified experimentally. The methods provided improved sensitivities for the hydride-forming elements compared with the respective conventional nebulization (Neb) systems by factors of 67 (As) and 64 (Sb) for ICP-AES and 36 (As) and 54 (Sb) for ICP-MS. Slight sensitivity improvements were also observed for the non-hydride-forming elements. The limits of detection (LOD) of As and Sb were lowered, respectively, to 0.8 and 0.9 μg L⁻¹ with the DM-ICP-AES system and to 0.01 and 0.02 μg L⁻¹ with the DM-ICP-MS system. The short-term stabilities of both methods were between 2.1 and 5.4%. The methods were applied for the analysis of leachates of a cement mortar material prepared in the pH range 3–13. The elemental concentration of the leachates determined by the two DM methods were statistically compared with the values obtained from Neb-ICP-MS analysis; the values showed good agreement at the 95% confidence level. Quantitative spike recoveries were obtained for the analytes from most of the leachates using both DM methods. Figure Schematic of the dual-mode sample introduction system used in combination with ICP-AES and ICP-MS for the simultaneous determination of hydride and non-hydride-forming elements     

Extraction and pre-concentration of platinum and palladium from microwave-digested road dust via ion exchanging mesoporous silica microparticles prior to their quantification by quadrupole ICP-MS

We report on the use of mesoporous silica microparticles (μPs) functionalized with quarternary amino groups for the isolation of platinum and palladium tetrachloro complexes from aqueous road dust digests. The μPs have a size ranging from 450 to 850 nm and are suspended directly in the aqueous digests, upon which the anionic Pt and Pd complexes are retained on the cationic surface. Subsequently, the μPs are separated by centrifugation. Elements that cause spectral interferences in ICP-MS determination of Pt and Pd can be quantitatively removed by adding fresh 0.240 mol L⁻¹ HCl to the μPs and by repeating the centrifugation step. The analyte-loaded μPs are then dissolved in 0.1 mL of 2 mol L⁻¹ HF, diluted to 2 mL, and the solutions thus obtained are analyzed by quadrupole ICP-MS. This method avoids analyte elution from the sorbent. This “dispersed particle extraction” approach yielded a run-to-run relative standard deviation ≤ 5 % for Pt and ≤ 4 % for Pd (at 0.1 ng mL⁻¹, n = 4 road dust digests). Method detection limits (expressed as concentrations in the dust samples) are 2 and 1 ng g⁻¹ for Pt and Pd, respectively. The method was validated by analysis of a reference material (BCR CRM 723) and applied to the analysis of road dust samples collected in downtown Vienna. Pt and Pd concentrations in samples collected in summer and in winter were compared, with concentrations ranging from 205 to 1445 ng g⁻¹ for Pt and from 201 to 1230 ng g⁻¹ for Pd.

Mesoporous silica microparticles (μPs) functionalized with quarternary amino groups were used for isolating platinum and palladium from aqueous road dust digests. The μPs were suspended directly in the aqueous digests, and the analyte-loaded μPs were analyzed using “dispersed particle extraction”.

     

Occurrence of Volatile Metal and Metalloid Species in Landfill and Sewage Gases

Abstract

Speciation of volatile metals and metalloids in the environment is extensively described in literature. In order to investigate unstable volatile organometallics, on-line coupling of GC with ICP-MS was used. Preliminary results for gases of sewage sludge fermentation at thermophilic and mesophilic conditions are compared with the metal and metalloid speciation in landfill gases. In each case 20 L gas were sampled by cryogenic trapping. The species were identified by element-specific detection either by retention time of standards or by calculation of the boiling point correlation. Characteristic of the separation is the linear correlation of boiling point (bp/°C) versus retention time (rt/min) (bp = 6.39?rt -109.2, r² = 0.9926). The amounts of total volatile elements are estimated by semi-quantification. Cd, Sn. Hg, Pb (sewage gas) and Se, Te, Hg, Pb (landfill gas) were determined in the range of ng m^?3 level; As, Sb, Te and Bi (sewage gas) and As, Sn, Sb and Bi (landfill gas) in the μg m^?3 level range.     

Use of granulated modified zeolite Y for the removal of inorganic arsenic and selenium species

Column studies were performed to evaluate the performance of modified zeolite-Y with ion Fe (zeolite-FeY) in removing As(III), As(V), Se(IV) and Se(VI) from groundwater. The removal capacities for zeolite-FeY was carried out on arsenic and selenium species in aqueous solution by co-precipitation technique with DBDTC-Pp complex in the pH range of 1.5–2.5 followed by the neutron activation analysis (NAA) using a TRIGA-MkII reactor with an average flux of 2.1 × 10¹² neutrons cm⁻² s⁻¹ and inductively coupled plasma-mass spectrometry (ICP-MS) technique as comparison. The accuracy between the results obtained from both techniques were compared and evaluated.     

Isotopic fractionation of mercury induced by reduction and ethylation

Isotope ratio measurements characterizing ²⁰²Hg/²⁰⁰Hg in NIST SRM 3133 Mercury Standard Solution were undertaken by multicollector inductively coupled plasma mass spectrometry employing NIST SRM 997 Tl for mass bias correction by use of the slope and the intercept obtained from a natural logarithmic plot of each session of measurements of ²⁰²Hg/²⁰⁰Hg against ²⁰⁵Tl/²⁰³Tl. The calculated value of 1.285333 ± 0.000192 (mean and one standard deviation, n = 40) for the mass bias corrected ²⁰²Hg/²⁰⁰Hg was then used for mass bias correction of other Hg isotope pairs. Ratios of 0.015337 ± 0.000011, 1.68770 ± 0.00054, 2.3056 ± 0.0015, 1.3129 ± 0.0013, 2.9634 ± 0.0038, and 0.67937 ± 0.0013 (expanded uncertainty, k = 2) were obtained for ¹⁹⁶Hg/¹⁹⁸Hg, ¹⁹⁹Hg/¹⁹⁸Hg, ²⁰⁰Hg/¹⁹⁸Hg, ²⁰¹Hg/¹⁹⁸Hg, ²⁰²Hg/¹⁹⁸Hg, and ²⁰⁴Hg/¹⁹⁸Hg, respectively. Reduction of Hg(II) to Hg⁰ in solutions of SRM 3133 was then undertaken using SnCl₂, NaBH₄, UV photolysis in the presence of formic acid, and ethylation of Hg(II) using NaBEt_4. These reactions induced significant isotope fractionation with maximum values of 1.17 ± 0.07, 1.08 ± 0.09, 1.34 ± 0.07, and 3.59 ± 0.09‰ (one standard deviation, 1SD, n = 5) for δ ^202/198Hg relative to the initial isotopic composition in the solution following 85–90% reduction of the Hg by SnCl₂, NaBH₄, UV photolysis, and ethylation with NaBEt₄, respectively. Mass-dependent fractionation was found to be dominant for all reduction processes. Figure Mass dependence of fractionation for all samples from Hg fractionation experiments using NaBEt₄. Solid lines are the theoretically predicted MDF based on δ′ ^202/198 Hg using equation 7. Error bars displayed are one standard deviation of the mean of 5 measurements of each sample     

Low level detection of <Superscript>135</Superscript>Cs and <Superscript>137</Superscript>Cs in environmental samples by ICP-MS

The measurement of fission product cesium isotopes ¹³⁵Cs and ¹³⁷Cs at low femtogram (fg) 10⁻¹⁵ levels in ground water by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) is reported. To eliminate the natural barium isobaric interference on the cesium isotopes, in-line chromatographic separation of the cesium from barium was performed followed by high sensitivity ICP-MS analysis. A high efficiency desolvating nebulizer system was employed to maximize ICP-MS sensitivity ~10 cps/fg. The three sigma detection limit for ¹³⁵Cs was 2 fg/mL (0.1 μBq/mL) and for ¹³⁷Cs 0.9 fg/mL (0.0027 Bq/mL) measured from the standard with analysis time of less than 30 min/sample. Cesium detection and 135/137 isotope ratio measurement at very low femtogram levels using this method in a spiked ground water matrix is also demonstrated.     

GC–MS analysis of low-molecular-weight dicarboxylic acids in atmospheric aerosol: comparison between silylation and esterification derivatization procedures

This paper describes methods for the determination of low-molecular-weight (LMW) dicarboxylic acids in atmospheric aerosols as important chemical tracers for source apportionment of aerosol organics and for studying atmospheric processes leading to secondary organic aerosol formation. The two derivatization procedures most widely used in GC analysis of dicarboxylic acids were compared: esterification using BF₃/alcohol reagent and silylation using N,O-bis(trimethylsilyl)-trifluoroacetamide (BSTFA). The advantages and drawbacks of the two methods are investigated and compared in terms of (1) precision and accuracy of the results and (2) sensitivity and detection limit of the procedure. The comparative investigation was performed on standard solutions containing target C₃–C₉ dicarboxylic acids and on experimental particulate matter (PM) samples. Attention was focused on low-volume sampling devices that collect small amounts of sample for organic speciation. The results show that, overall, both the techniques appear suitable for the analysis of LMW dicarboxylic acids in atmospheric aerosols since they provide low detection limits (≤4 ng m⁻³) and satisfactory reproducibility (RSD% ≤ 15%). Between them, BSTFA should be the reagent of choice under the most limiting conditions of PM filters collected by low-volume air samplers: It provides determination of all the target C₃–C₉ dicarboxylic acids with lower detection limits (≤2 ng m⁻³) and higher reproducibility (RSD% ≤ 10%)      

Optimization of parameters for semiempirical methods. III Extension of PM3 to Be,Mg, Zn,Ga, Ge,As, Se,Cd, In,Sn, Sb,Te, Hg,Tl, Pb,and Bi

Using a recently developed procedure for optimizing parameters for semiempirical methods,¹ PM3 has been extended to a total of 28 elements. Average ΔH_f errors for the newly parameterized elements are Be: 8.6, Mg: 8.4, Zn: 5.8, Ga: 14.9, Ge: 11.4, As: 8.5, Se: 11.1, Cd: 2.6, In: 11.3, Sn: 9.0, Sb: 13.7, Te: 11.3, Hg: 6.8, Tl: 6.5, Pb: 7.4, and Bi: 10.9 kcal/mol. For some elements the paucity of data has resulted in a method, which, while highly accurate, is likely to be only poorly predictive.     

Estimations with hypovanadous salts

Summary It has been shown that Cu, Hg, Sb, Bi, Se, Te, Au, Pt and Pd precipitated from their compounds in elementary form and thus be determined gravimetrically by vanadium(II) sulphate solution.

---

Zusammenfassung Cu, Hg, Sb, Bi, Se, Te, Au, Pt und Pd können mit Vanadium(II)-sulfatlösung aus ihren Verbindungen in elementarer Form gefällt und gravimetrisch bestimmt werden.

---

---

Part II: Z. analyt. Chem.189, 406 (1962).     

Determination of <Superscript>237</Superscript>Np, <Superscript>93</Superscript>Zr and other long-lived radionuclides in medium and low level radioactive waste samples

The majority of long-lived radionuclides produced in the nuclear fuel cycle can be regarded as “difficult-to-measure” nuclides, hence chemical separation is needed before the nuclear measurement of them. A combined radiochemical procedure that enables the simultaneous determination of some “difficult-to-measure” nuclides in medium and low level radioactive wastes has been developed in our laboratory. Recently, this method has been extended for determination of ²³⁷Np and ⁹³Zr. ²³⁷Np and ⁹³Zr are pre-concentrated by co-precipitation on iron(II) hydroxide and zirconium oxide, separated by extraction chromatography using UTEVA, and measured by inductively coupled plasma mass spectrometry (ICP-MS). As even traces of polyatomic ions and isotopes at m/z 237 or 93 cause considerable interferences during ICP-MS detection, a purification step by extraction chromatography was needed. Analyzing real samples (evaporation concentrates of a nuclear power plant) 66–99% and 31–99% chemical yields were achieved for Np and Zr, respectively.     

Structural and spectroscopic trends in mononuclear arylchalcogenolato-palladium(II) and -platinum(II) complexes: Crystal structures of [M(TeAr)2(dppe)] {M = palladium, platinum; Ar = phenyl, 2-thienyl; dppe = 1,2-bis(diphenylphosphino)ethane}

A series of mononuclear [M(EAr)₂(dppe)] [M = Pd, Pt; E = Se, Te; Ar = phenyl, 2-thienyl; dppe = 1,2-bis(diphenylphosphino)ethane] complexes has been prepared in good yields by the reactions of [MCl₂(dppe)] and corresponding ArE⁻ with a special emphasis on the aryltellurolato palladium and -platinum complexes for which the existing structural information is virtually non-existent. The complexes have crystallized in five isomorphic groups: (1) [Pd(SePh)₂(dppe)] and [Pt(SePh)₂(dppe)], (2) [Pd(TePh)₂(dppe)] and [Pt(TePh)₂(dppe)], (3) [Pd(SeTh)₂(dppe)], (4) [Pt(SeTh)₂(dppe)] and [Pd(TeTh)₂(dppe)], and (5) [Pt(TePh)₂(dppe)]. In addition, solvated [Pd(TePh)₂(dppe)] · CH₃OH and [Pd(TeTh)₂(dppe)] · 1/2CH₂Cl₂ could be isolated and structurally characterized. The metal atom in each complex exhibits an approximate square-planar coordination. The Pd-Se, Pt-Se, Pd-Te, and Pt-Te bonds span a range of 2.4350(7)-2.4828(7) Å, 2.442(1)-2.511(1) Å, 2.5871(7)-2.6704(8) Å, and 2.6053(6)-2.6594(9) Å, respectively, and the respective Pd-P and Pt-P bond distances are 2.265(2)-2.295(2) Å and 2.247(2)-2.270(2) Å. The orientation of the arylchalcogenolato ligands with respect to the M(E₂)(P₂) plane has been found to depend on the E-M-E bond angle. The NMR spectroscopic information indicates the formation of only cis-[M(EAr)₂(dppe)] complexes in solution. The trends in the ³¹P, ⁷⁷Se, ¹²⁵Te, and ¹⁹⁵Pt chemical shifts expectedly depend on the nature of metal, chalcogen, and aryl group. Each trend can be considered independently of other factors. The ⁷⁷Se or ¹²⁵Te resonances appear as second-order multiplets in case of palladium and platinum complexes, respectively. Spectral simulation has yielded all relevant coupling constants.     

Preliminary results of a quick,simple method of detecting antimony in water samples

Preliminary results of development of a direct and fast method of determination of antimony in samples of tap water using GFAAS are presented. The found levels of antimony were lower than permitted for human consumption. A mixture of Pd and Mg(NO₃)₂ (concentrations in the injected solution: 8.6 μg mL⁻¹ and 5.8 μg mL⁻¹ respectively) was used as the chemical modifier. The pyrolysis and atomization temperatures were 1000 and 1700°C, respectively and the mean analytical recovery 98.2%.