高效液相色谱法和毛细管电泳法测定甘草制品中甘草酸的含量

分别用高效液相色谱法（ＨＰＬＣ）、毛细管区带电泳法（ＣＺＥ）、胶束电动毛细管色谱法（ＭＥＣＣ）测定了甘草制品中甘草酸的含量。对ＨＰＬＣ,ＣＺＥ,ＭＥＣＣ的分析条件作了一些选择实验,结果表明ＭＥＣＣ法与ＨＰＬＣ法分析数据接近、比较准确,而且前者比ＨＰＬＣ法分离效率高、溶剂用量少,是一种很有发展潜力的分析方法。     

Determination of enantiomers in a synthetic argininal peptide using capillary zone electrophoresis and high-performance liquid chromatography

SCH 201781 is a synthetic argininal peptide containing two chiral centers and an aromatic sulfonamide group. It can exist as four reversible forms, the aldehyde, the hydrate, and two diastereomeric aminals. Capillary zone electrophoresis (CZE) and reversed-phase high-performance liquid chromatographic (HPLC) methods were developed to separate and quantitate the enantiomers in SCH 201781. Comparable results were obtained using both methods. The CZE method uses direct injection, while the HPLC method requires a precolumn derivatization and is more time consuming. The CZE method provides superior sensitivity to the HPLC method. Both methods were shown to be precise and reproducible.     

Development and validation of capillary zone electrophoresis and high-performance liquid chromatography methods for the determination of oral anticoagulant edoxaban in pharmaceutical tablets

The incidence of thrombotic complications in SARS-CoV-2 infections has become a global concern; thus, anticoagulants are an integral part of the treatment. Edoxaban (EDX) is an oral anticoagulant suitable for pharmacologic thromboprophylaxis. Herein, two novel analytical methods for EDX determination in tablets are developed and validated using capillary zone electrophoresis (CZE) and high-performance liquid chromatography (HPLC). Operating conditions such as the electrolyte's concentration and pH value, injection time, volume, and the capillary temperature, were optimized. The methods were successfully validated by establishing the linearity, intra- and inter-day precisions (relative standard deviation [%]), accuracy, and robustness. Adequate separation of excipients and degradation products of EDX generated by stress degradation conditions demonstrated the stability-indicating capability of the methods. The analytical procedures were linear in the range of 25–125 µg/ml (r > 0.999), with the limits of detection and quantification of 3.26 and 10.87 µg/ml for CZE and 0.740 and 2.78 µg/ml for HPLC. Although both methodologies are suitable for determining EDX in tablets, CZE provides a greener alternative due to low-cost analysis using less organic solvents and minimizing waste generation.     

Analysis of melamine resins by capillary zone electrophoresis with electrospray ionization-mass spectrometric detection

A method for the determination of the major components of (methoxymethyl)melamine resins, with quantitative analysis of unreacted melamine by capillary zone electrophoresis (CZE) using electrospray ionization-mass spectrometry (ESI-MS) is presented. Using a low background electrolyte (BGE) pH, components are separated according to their charge/ionic radius ratio with a distinctly different separation selectivity compared to the HPLC methods commonly employed in melamine-resin analysis. The use of a time-of-flight mass spectrometer (TOF-MS) was concluded to be necessary, as the complex samples studied required maximum sensitivity and resolution, which is clearly superior for TOF-MS detectors over their quadrupole counterparts. A standard curve of free melamine was determined with an R(2) = 0.999 over a concentration range of an order of magnitude. This method offers the unique separation selectivity of CZE as well as a quicker analysis time, especially for dimers compared to the HPLC methods used to date.     

CZE separation of strawberry anthocyanins with acidic buffer and comparison with HPLC

Anthocyanins, the major colourants of strawberries, are polar pigments that are positively charged at low pH. Herein, we have assessed a new analytical method for the separation of anthocyanins using CZE. Acidic buffer solutions (pH <2) were employed in order to maintain pigments in the cation flavylium form and achieve high molar absorptivity at 510 nm. These spectral properties enabled us to identify strawberry anthocyanins in a preliminary stage by detection in the visible range, although the method was optimised at 280 nm to obtain the best S/N. The effects of buffer composition highlighted the necessity of adding an organic modifier to the running buffer to obtain a suitable separation. The electrophoretic method permitted the separation of the three main anthocyanins of strawberry extracts, namely pelargonidin 3-glucoside (Pg-glu), pelargonidin 3-rutinoside and cyanidin 3-glucoside. The electrophoretic results, expressed as retention time and separation efficiency of the major anthocyanin (Pg-glu), were compared to those achieved in HPLC, the analytical technique traditionally used for the investigation of anthocyanins in vegetable matrix. The content of Pg-glu in strawberries (cv. Camarosa), calculated with HPCE and HPLC methods, resulted respectively in 11.41 mg/L and 11.37 mg/L.     

Determination of tobacco-specific N-nitrosamines in rabbit serum by capillary zone electrophoresis and capillary electrophoresis-electrospray ionization-mass spectrometry with solid-phase extraction

In this paper, we propose a new strategy for separation and determination of tobacco-specific N-nitrosamines (TSNAs), a group of strong carcinogens found only in tobacco products, by using CZE and CE-MS associated with SPE. Six TSNAs: N'-nitrosonornicotine, N'-nitrosoanatabine, N'-nitrosoanabasine, 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone, 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol, and 4-(methylnitrosamino)-4-(3-pyridyl)-1-butanol were simultaneously separated by either of two CZE methods, one of which worked with ammonium formate buffer (pH 2.5) and another with citrate buffer (pH 2.4), as well as a CE-MS method. The CZE conditions including pH and concentration of running buffer, capillary length, applied voltage, and capillary temperature were systematically optimized. For CE-MS method, an optimized sheath liquid consisted of methanol-water was used at a flow rate of 10 muL/min. With SPE procedure, our proposed CE-MS method was successfully applied to determine TSNAs after 15 min metabolism in rabbits. A comparison study between CZE and CE-MS methods for quantitative purposes was carried out, showing that both methods provided similar separation efficiency, selectivity, repeatability, linearity, and recovery. However, CE-MS method was better suited for the analysis of TSNAs in complicated biological samples for its sensitivity and extra information on molecular structure. Having good accordance with our previous work by using LC-MS, the new CE-MS method is expected to be an alternative to the LC-MS method and applied to study the metabolism of TSNAs.     

Determination of (E)-10-hydroxy-2-decenoic acid content in pure royal jelly: a comparison between a new CZE method and HPLC

A new CZE method was developed and compared with HPLC for the determination of (E)-10-hydroxy-2-decenoic acid (10-HDA) in royal jelly (RJ) samples of different geographical origin. The results obtained with the CZE method were highly correlated with those of HPLC (p < 0.01). Under optimized conditions, CZE employed minimal amounts of 50 mM tetraborate buffer as BGE, without the addition of organic solvents, EOF or pH modifiers. The CZE method showed a wide linear response range (0.006-0.808 mg 10-HDA/mL), a good sensitivity (LOD and LOQ were 0.002 and 0.004 mg/mL, respectively) and a satisfactory instrumental repeatability with respect to migration time and peak area (RSD% less than 1.0 and 2.0% on migration time for intra- and interday assay, respectively and less than 2.0 and for 4.0% on peak area for intra- and interday assay, respectively). The 10-HDA content in RJ ranged from 0.8 to 3.2 g/100 g of RJ and a significant difference (p < 0.05) was found between the Italian and extra-European average values: 2.5 and 1.6 g/100 g of RJ, respectively, according to the CZE data. The possibility of application of CZE for routine analyses on RJ and RJ based products to verify their authenticity is highlighted here.     

Separation of diastereomers of phosphinic pseudopeptides by capillary zone electrophoresis and reverse phase high‐performance liquid chromatography

Capillary zone electrophoresis (CZE) and reverse phase high‐performance liquid chromatography (RP‐HPLC) were used for separation of diastereomers of phosphinic pseudopeptides in achiral separation media. A set of phosphinic pseudopeptides, i. e. peptides with one peptide bond substituted by phosphinic acid moiety ‐PO₂^–‐CH₂‐ derived from the structure N‐Ac‐Val‐AlaB(‐CH₂)Leu‐His‐NH₂ synthesized as a mixture of four diastereomers was used. Separations of diastereomers by CZE were carried out in Tris‐phosphate background electrolytes in the pH range 1.1–3.2 and at least partial separation of the four diastereomers of each pseudopeptide was achieved. A routinely used RP‐HPLC method (C₁₈‐silica column and water/acetonitrile/trifluoroacetic acid mobile phase) was also capable of resolving the diastereomers. In addition, since individual diastereomers of majority of the pseudopeptides were isolated by RP‐HPLC it was possible to check the purity of these RP‐HPLC separated diastereomers and to compare the migration order of the diastereomers in CZE with their elution order in RP‐HPLC. The results obtained by CZE and RP‐HPLC demonstrate a complementarity of both methods in analysis and separation of phosphinic pseudopeptides including their diastereomers.     

Determination of Vecuronium Bromide in Pharmaceuticals: Development, Validation and Comparative Study of HPLC and CZE Analytical Methods

Vecuronium bromide is a neuromuscular blocking agent used for anesthesia to induce skeletal muscle relaxation. HPLC and CZE analytical methods were developed and validated for the quantitative determination of vecuronium bromide. The HPLC method was achieved on an amino column (Luna 150 × 4.6 mm, 5 μm) using UV detection at 205 nm. The mobile phase was composed of acetonitrile:water containing 25.0 mmol L^?1 of sodium phosphate monobasic (50:50 v/v), pH 4.6 and flow rate of 1.0 mL min^?1. The CZE method was achieved on an uncoated fused-silica capillary (40.0 cm total length, 31.5 cm effective length and 50 μm i.d.) using indirect UV detection at 230 nm. The electrolyte comprised 1.0 mmol L^?1 of quinine sulfate dihydrate at pH 3.3 and 8.0% of acetonitrile. The results were used to compare both techniques. No significant differences were observed (p > 0.05).     

Determination of aristolochic acids in medicinal plants (Chinese) prepared medicine using capillary zone electrophoresis

Aristolochic acids (I and II) are commonly found in medicinal plants such as Radix aristolochiae and have been reported to cause acute hepatitis and end-stage renal failure. The aim of this work was to develop a method for the analysis of aristolochic acids in medicinal plant/Chinese prepared medicine (CPM) using (CZE). The buffer used was 30 mM sodium tetraborate at pH 9.5, detection was at 254 nm, applied voltage at 18 kV and the temperature was set at 25 degrees C. The effect of ionic strength, pH, and applied voltage on the separation was investigated. The precision values (relative standard deviation, RSD, %) for the relative migration time and peak area or peak height for aristolochic acids I and II were found to be less than 0.3% and between 2.6 to 4.0%, respectively. The limit of detection for aristolochic acids I and II was found to be 1.2 and 0.9 mg/L, respectively. The proposed method using pressurized liquid extraction (PLE) with CZE was used to determine the amount of aristolochic acids in medicinal plants or CPM samples with complex matrix and the results were compared with high-performance liquid chromatography (HPLC). Method precision (RSD, n = 6) was found to be less than 4% when those from applied to medicinal plants and CPM samples.     

Validation of a capillary zone electrophoresis method for the comparative determination of etoricoxib in pharmaceutical formulations

A CZE method was developed and validated for the analysis of etoricoxib in pharmaceutical dosage forms, using prilocaine as an internal standard. The CZE method was carried out on a fused-silica capillary (50 microm id, effective length 40 cm). The BGE consisted of 25 mM tris-phosphate solution at pH 2.5. The capillary temperature was maintained at 35 degrees C, the applied voltage was 25 kV, the injection was performed using the pressure mode at 50 mbar for 5 s, with detection at 234 nm using a photodiode array detector. The method was linear in the range of 2-150 microg/mL (r(2) = 0.9999). The specificity and stability-indicating capability were proven through the degradation studies and showing also that there was no interference of the excipients of the formulation. The accuracy was 99.49% with RSD of 0.66%. The limits of quantitation and detection were 2 and 0.58 microg/mL, respectively. Moreover, method validation demonstrated acceptable results for the precision, sensitivity, and robustness. The proposed method was successfully applied for the quantitative analysis of etoricoxib pharmaceutical formulations, and the results compared to the HPLC and LC-MS/MS methods, showing nonsignificant difference (p >0.05).     

Interactions of Proteins with the Acidic Components of the Electrolyte Solution and Their Role in the Performance of Separations by CZE

This paper reports the results of a study performed to investigate the dependence of the performance of protein separation by capillary zone electrophoresis (CZE) on the anionic component of the electrolyte solutions consisting of 20 mM N,N,N′,N′-tetramethyl-1,3-butanediamine (TMBD) titrated to either pH 4.0 or pH 6.5 with either a monoprotic or a polyprotic acid. With the exception of hydrochloric acid, the acids were selected among those commonly used as the constituents of the solutions employed for protein analysis by either HPLC or CZE. TMBD was chosen for its effectiveness at preventing the interactions of proteins with the inner wall of bare fused-silica capillaries. The performance of separations was evaluated using four basic model proteins having pI value and molecular mass ranging from 9.5 to 11.0 and from 12,400 to 25,000 Da, respectively. It is shown that the different acids used as the components of the background electrolyte solutions, all containing the same concentration of TMBD, affect to different extents both migration time and peak shape of the tested proteins. The performance displayed by the BGE containing phosphate ions is enhanced using TMBD in combination with diethylenetriamine, an aliphatic vicinal triamine having effective buffering capacity at pH 4.0 and capability at minimizing protein–capillary wall interactions. The reported experimental evidences are discussed based on the possible interactions that the phosphate ions are known to establish with both the protein molecules and the surface of bare fused-silica capillaries.     

Analysis of Carbaryl and carbofuran in tobacco samples by HRGC,HPLC, and CZE

Determination of carbamate residues in tobacco samples was carried out by three different methods, two having been described in the literature and one developed for the purpose of this work. The extracts were analyzed by HRGC-FID (using derivatization), by HPLC-RP with photodiode array detection and by Capillary Zone Electrophoresis (CZE) with UV detection. The extraction method developed used in conjunction with capillary zone electrophoresis showed to be the most suitable for carbamate residue analysis in real tobacco samples. The developed method presented better recovery results in relation to the others. CZE allowed the determination of carbamate residue in real tobacco sample while HPLC and HRGC could not do this, due to co-elution problems.     

Determination of rimantadine in pharmaceutical preparations by capillary zone electrophoresis with indirect detection or after derivatization

Summary Rimantadine is synthetic analog of amantadine; both are antiviral agents used for prophylaxis and treatment of influenza A. A capillary zone electrophoretic (CZE) procedure for the determination of rimantadine has been developed. As the direct determination of rimantadine is poorly sensitive because the compound is almost transparent in the UV/Vis range, several indirect methods were studied. Two were found to be the particularly useful: (a) indirect detection using 5 mM 4-methylbenzylamine in 1:4 methanol-water as absorbing background electrolyte, with detection at 210 nm, and (b) derivatization of rimantadine with 1,2-naphthoquinone-4-sulfonic acid in alkaline medium and subsequent determination of the derivative by CZE (40 mM tetraborate, pH 9.2, detection at 280 nm). Uncoated capillary tubing, 44 cm length ×75 μM i.d., was used for both determinations. The detection limits were 0.1 and 2 ppm for methods a and b, respectively. The methods were used to determine rimantadine in pharmaceutical products and for dissolution testing of Flumadin^? tablets.     

毛细管电泳法和高效液相色谱法拆分联萘二酚酸对映体

采用毛细管电泳法和高效液相色谱法直接拆分2,2′-二羟基-1,1′-联二萘-3,3′-二甲酸(HBNC)对映体.以四种不同的β-环糊精为手性添加剂,考察环糊精的种类与浓度、缓冲液pH值及浓度、分离电压、温度等因素对HBNC分离的影响.结果表明:采用10 mmol/L磺丁基醚-β-环糊精+20 mmol/L磷酸盐缓冲液(pH=7.0),20 kV分离电压,HBNC对映体在20 min内达到基线分离,分离度达到3.31.采用(S)-叔-亮氨酸基-(S)-1-(α-萘基)乙胺手性柱,正己烷-乙醇-三氟乙酸(97∶3∶0.2,V/V)流动相,HBNC对映体在40 min内也基本达到基线分离.     

Modeling the zeta potential of silica capillaries in relation to the background electrolyte composition

A theoretical relation between the zeta potential of silica capillaries and the composition of the background electrolyte (BGE) is presented in order to be used in capillary zone electrophoresis (CZE). This relation is derived on the basis of the Poisson-Boltzmann equation and considering the equilibrium dissociation of silanol groups at the capillary wall as the mechanism of charge generation. The resulting model involves the relevant physicochemical parameters of the BGE-capillary interface. Special attention is paid to the characterization of the BGE, which can be either salt or/and buffer solutions. The model is successfully applied to electroosmotic flow (EOF) experimental data of different aqueous solutions, covering a wide range of pH and ionic strength. Numerical predictions are also presented showing the capability of the model to quantify the EOF, the control of which is relevant to improve analyte separation performance in CZE.     

Separation of small peptides by electrochromatography on silica-based reversed phases and hydrophobic anion exchange phases

Peptide separations are regarded as a promising application of capillary electrochromatography (CEC) and, at the same time, a suitable model to elucidate its mixed separation mechanism when charged analytes are involved. In this paper, studies on the separation of small peptides (2-4 amino acids) on a Spherisorb octadecyl silane (ODS) phase at acidic pH and on a strong anion exchange (SAX)/C18 mixed mode phase at weakly basic pH are reported. For the ODS phase a comparison of CEC, capillary zone electrophoresis (CZE) and high-performance liquid chromatography (HPLC) under identical buffer/eluent conditions is presented. The predicted retention factors for CEC under the assumption of simple superposition of HPLC retention and CZE migration matched the measured results for the peptides that had small retention factors in HPLC. For both types of stationary phases, a variation of the acetonitrile content in the mobile phase led to a wide range of retention factors, including negative values when co-electroosmotic migration was dominant. Though both the ODS and the SAX/C18 phase offer unique advantages, the SCX/C18 phase at pH 9 provides more flexibility to alter separation selectivity for the selected peptides.     

Comparison of shikimic acid determination by capillary zone electrophoresis with direct and indirect detection with liquid chromatography for varietal differentiation of red wines

Two capillary zone electrophoretic (CZE) methods for determination of shikimic acid in Chilean red wine were developed and compared with a HPLC method. Both electrophoretic methods were carried out by using a reversed electroosmotic flow induced by trimethyl(tetradecyl)ammoniumbromide (TTAB) with indirect detection at 260 nm using p-aminobenzoic acid as a UV-absorbing co-ion or by direct detection at 213 nm. In both cases, the separation was carried out in a 50 microm I.D. uncoated capillary with an effective length of 48 cm, a negative power supply of 30 kV, using a buffer based on bis[2-hydroxyethyl]imino-tris[hydroxymethyl]methane (Bis-Tris), pH 7.0 or 7.5 and hydrodynamic injection. The chromatographic separations were carried out on a C-18 reversed phase column followed by a sulfonyl-styrene-divinylbenzene (S-DVB) ion exclusion column at 70 degrees C with H2SO4 0.02 M as isocratic mobile phase and a flow rate of 0.5 mL min(-1). The three methods allowed the quantification of shikimic acid with quantification limits between 1.0 and 12.0 mg L(-1) and precision between 7.3 and 10.1%, however, only the concentrations obtained by CZE with direct detection were statistically similar to those of HPLC. This parameter was evaluated as analytical tool to verify varietal authenticity of red wines. In all cases, the Cabernet Sauvignon wines presented higher concentrations of shikimic acid, compared with Merlot or Carmenère wines.     

Capillary electrophoresis for the analysis of paralytic shellfish poisoning toxins in shellfish: Comparison of detection methods

Paralytic shellfish toxins (PSTs) are produced by marine and freshwater microalgae and accumulate in shellfish including mussels, oysters, and scallops, causing possible fatalities when inadvertently consumed. Monitoring of PST content of shellfish is therefore important for food safety, with currently approved methods based on HPLC, using pre‐ or postcolumn oxidation for fluorescence detection (HPLC‐FLD). CE is an attractive alternative for screening and detection of PSTs as it is compatible with miniaturization and could be implemented in portable instrumentation for on‐site monitoring. In this study, CE methods were developed for C⁴D, FLD, UV absorption detection, and MS—making this first report of C⁴D and FLD for PSTs detection. Because most oxidized toxins are neutral, MEKC was used in combination with FLD. The developed CZE‐UV and CZE‐C⁴D methods provide better resolution, selectivity, and separation efficiency compared to CZE‐MS and MEKC‐FLD. The sensitivity of the CZE‐C⁴D and MEKC‐FLD methods was superior to UV and MS, with LOD values ranging from 140 to 715 ng/mL for CZE‐C⁴D and 60.9 to 104 ng/mL for MEKC‐FLD. With the regulatory limit for shellfish samples of 800 ng/mL, the CZE‐C⁴D and MEKC‐FLD methods were evaluated for the screening and detection of PSTs in shellfish samples. While the CZE‐C⁴D method suffered from significant interferences from the shellfish matrix, MEKC‐FLD was successfully used for PST screening of a periodate‐oxidized mussel sample, with results confirmed by HPLC‐FLD. This confirms the potential of MEKC‐FLD for screening of PSTs in shellfish samples.     

Evaluation of capillary electrophoretic techniques towards systematic toxicological analysis.

Two capillary electrophoresis (CE) methods were evaluated for their suitability in systematic toxicological analysis (STA). A test set of 25 barbiturates was analysed using capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC). Buffers used consisted of 90 mM borate set at pH 8.4 (CZE) and 20 mM phosphate, 50 mM sodium dodecyl sulphate set at pH 7.5 (MEKC). All analyses were carried out using fused silica capillaries using an electric field strength of 52.6 kV/m. The use of a reproducible identification parameter is very important in STA as it influences the identification power (IP). To deal with the poor reproducibility of the migration time, we introduced the corrected effective mobility. Inter-day reproducibilities of the latter parameter were < 0.6% for CZE and < 0.5% for MEKC, using daily prepared buffers. The IP of the methods was expressed by calculation of the discriminating power and the mean list length. Data obtained were compared to gas chromatographic and high-performance liquid chromatographic data, and correlations between all methods were calculated. It was shown that little correlation exists between chromatographic and electrophoretic techniques. The results indicated that CE has a good identification power for the application in STA, especially when a combination of methods having a low correlation is used.