Development and certification of a coal fly ash certified reference material for selected polycyclic aromatic hydrocarbons

The development and certification of a coal fly ash certified reference material (CRM) for polycyclic aromatic hydrocarbons (PAH) is described; this is the first natural matrix CRM for organic environmental analysis in China. The homogeneity and stability of this material have been tested by HPLC. The concentrations of several PAH were determined by use of two independent, different methods--solvent extraction-HPLC analysis with UV detection coupled with fluorescence detection (FLD) and solvent extraction, isolation with a silica column, and GC analysis with flame ionization detection (FID). Five certified values were determined: phenanthrene 7.1 +/- 2.6 microg g(-1), anthracene 2.0 +/- 0.8 microg g(-1), fluoranthene 7.4 +/- 1.9 microg g(-1), pyrene 7 +/- 2 microg g(-1), and benzo[a]pyrene 1.3 +/- 0.3 microg g(-1). Reference values for several other PAH are also suggested.     

Determination of Cr(VI) in plants by electrothermal atomic absorption spectrometry after leaching with sodium carbonate

The determination of chromium (VI) compounds in plants by electrothermal atomic absorption spectrometry (ET AAS) is proposed based on their leaching with 0.1 M Na₂CO₃. Due to the presence of relatively high amounts of Na₂CO₃ in the resulting samples, the temperature and time of pyrolysis and atomization stages must be optimized to minimize the influence of the matrix. A limit of detection (LOD) for determination of Cr(VI) in plants by ET AAS was found to be 0.024 μg g⁻¹.The concentration of Cr(VI) and total chromium in plants collected in different geographical areas (South Africa and Russia), grown on soils high in chromium was determined. The concentration of Cr(VI) and total Cr in stems and leaves of plants was in the range of 0.04–0.7 μg g⁻¹ and 0.5–10 μg g⁻¹, respectively. The limited uptake of Cr(III) by plants, in comparison to its concentration in soil, can be explained by the very low solubility of natural Cr(III) compounds.Results for the determination of Cr(VI) were confirmed by the analysis of BCR CRM 545 (Cr(VI) in welding dust) with good agreement between certified (39.5 ± 1.3 μg mg⁻¹) and found (38.8 ± 1.2 μg mg⁻¹) values. The total concentration of Cr in plants has also been determined by ET AAS after dry ashing of samples at 650 °C. Results were confirmed by the analysis of BCR CRM 281 (Trace elements in Rye Grass) with good agreement between the found (2.12 ± 0.16 μg g⁻¹) and certified value (2.14 ± 0.12 μg g⁻¹).     

Evaluation of different sample introduction approaches for the determination of boron in unalloyed steels by inductively coupled plasma mass spectrometry

An extended study of different sampling introduction approaches using inductively coupled plasma mass spectrometry (ICP-MS) is presented for the determination of boron in steel samples. The following systems for sample introduction were applied: direct sample solution nebulization by continuous nebulization (CN) using a cross-flow nebulizer and with flow injection (FI), applied to 0.1% (m/v) and 0.5% (m/v) sample solutions, respectively; FI after iron matrix extraction, using acetylacetone–chloroform, and isotopic dilution (ID) analysis as the calibration method; FI with on-line electrolytic matrix separation; and spark ablation (SA) and laser ablation (LA) as solid sampling techniques. External calibration with matrix-matching samples was used with CN, SA, and LA, and only acid solutions (without matrix matching) with FI methods. When FI was directly applied to a sample solution, the detection limit was of 0.15 μg g⁻¹, improving by a factor of 4 that was obtained from the CN measurements. Isotopic dilution analysis, after matrix removal by solvent extraction, made it possible to analyse boron with a detection limit of 0.02 μg g⁻¹ and, with the on-line electrolytic process, the detection limit was of 0.05 μg g⁻¹. The precision for concentrations above 10 times the detection limit was better than 2% for CN, as well as for FI methods. Spark and laser ablation sampling systems, avoiding digestion and sample preparation procedures, provided detection limits at the μg g⁻¹ levels, with RSD values better than 6% in both cases. Certified Reference Materials with B contents in the range 0.5–118 μg g⁻¹ were used for validation, finding a good agreement between certified and calculated values.     

Pressurized fluid extraction of polycyclic aromatic hydrocarbons using silanized extraction vessels

We have investigated the extraction efficiency of a pressurized fluid extraction system using an Ottawa sand matrix, soils and a certified reference material (HS-6) spiked with the 16 polycyclic aromatic hydrocarbon (PAHs) associated with method EPA 8100. Acceptable recoveries were achieved for all PAHs using a nominal sand concentration of 2.0 μg.g^-1. However, similar experiments that were conducted at a concentration of 0.20 μg.g^-1 afforded poor recoveries and poor reproducibility for the six-ring PAHs indeno(1,2,3-cd)pyrene, dibenz(a)anthracene, and benzo(ghi)perylene. These were not adequately addressed by the use of indeno(1,2,3-cd)pyrene-d12 and benzo(g,h,i)perylene-d12 surrogates. Silanization of vessels using dichlorodimethylsilane adequately passivates the system but is only required for the high surface area retention frits. Replicate analyses at concentrations of 200 and 20 ng.g^-1 demonstrated that detection limits in the low ppb range (ng.g^-1) are achieved for Ottawa sand, dry soil and soil with moisture contents up to a mass fraction of 30 %. Such performance is consistent with the analytical requirements of the Canadian Sediment Quality Guidelines. Improved analyte recoveries were also observed for the certified reference material HS-6 which were further improved by increasing extraction temperatures from 100 to 150 °C.

Certification of a pure reference material for the ginsenoside Rg 1

A pure certified reference material (CRM) for the ginsenoside Rg ₁ was prepared from roots of Panax ginseng by extraction and separation of ginsenosides. The mass fraction of the main component (ginsenoside Rg ₁ ) in the reference material was determined and its uncertainty was assessed from various input quantities, such as organic impurities, residual moisture, residual solvent, ash, and insoluble matters. To measure these input quantities, HPLC/CAD, Karl Fischer (KF) coulometry, gravimetry, and GC/FID were used. Homogeneity and long-term stability of the reference material are discussed. The certified mass fraction of Rg ₁ in the reference material is 0.974 ± 0.006 (k = 2) with a shelf life of 1 year.     

Certified reference material for quantification of polycyclic aromatic hydrocarbons in sediment from the National Metrology Institute of Japan

The National Metrology Institute of Japan has issued a certified reference material (CRM) of freshwater lake sediment for polycyclic aromatic hydrocarbon (PAHs) analyses. The certification used three extraction techniques: pressurized liquid extraction (PLE) with toluene, PLE with dichloromethane/ethyl acetate (1:1 by volume), and alkaline extraction (1 M KOH in methanol) in combination with microwave-assisted extraction. Both gas chromatography/mass spectrometry (GC/MS) and liquid chromatography/dopant-assisted atmospheric pressure photoionization/MS (LC/DA-APPI/MS) analyses were used. Certified values are provided for 18 PAHs at 1–25 μg kg⁻¹ except for perylene (2.08 × 10³ μg kg⁻¹), and information values are provided for two. Since the values of PAHs in the CRM are much lower than those in other CRMs and are comparable to those found at sites with little human influence, the CRM is suitable for PAH monitoring in sediment and soil samples.     

Certification of total arsenic in blood and urine standard reference materials by radiochemical neutron activation analysis and inductively coupled plasma-mass spectrometry

Radiochemical neutron activation analysis (RNAA) was used to measure arsenic at four levels in standard reference material (SRM) 955c Toxic Elements in Caprine Blood and at two levels in SRM 2668 Toxic Elements in Frozen Human Urine for the purpose of providing mass concentration values for certification. Samples were freeze-dried prior to analysis followed by neutron irradiation for 3 h at a fluence rate of 1 × 10¹⁴ cm^?2 s^?1. After sample dissolution in perchloric and nitric acids, arsenic was separated from the matrix either by retention on hydrated manganese dioxide (urine) or by extraction into zinc diethyldithiocarbamate in chloroform (blood). ⁷⁶As was quantified by gamma-ray spectroscopy. Differences in chemical yield and counting geometry between samples and standards were monitored by measuring the count rate of a ⁷⁷As tracer added before sample dissolution. RNAA results were combined with inductively coupled plasma-mass spectrometry values from National Institute of Standards and Technology and collaborating laboratories to provide certified values of 10.81 ± 0.54 and 213.1 ± 0.73 μg/L for SRM 2668 Levels I and II, and certified values of 21.66 ± 0.73, 52.7 ± 1.1, and 78.8 ± 4.9 μg/L for SRM 955c Levels II–IV, respectively. Because of discrepancies between values obtained by different methods for SRM 955c Level I, an information value of <5 μg/L was assigned for this material.     

A Total Solution to Baseline Separation of 20 Brominated Flame Retardant Additives in Electronic Products with Automated Soxhlet Hot Extraction and Gas Chromatography‐Mass Spectrometry

An efficient and reliable separation technique based on automated Soxhlet hot extraction (AHSE) was developed and validated. It can be applied to rapid separations of 20 persistent organic pollutants, including two types of brominated flame retardants (BFRs), polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) contained in nonmetallic component parts of electronic products. The qualitative chromatographic analyses were carried out by using a gas chromatography coupled with a mass spectrometry detector (GC‐MS). The 20 persistent organic pollutants were simultaneously and completely separated by a 15 meter HP‐5MS short capillary column in 25 minutes. Through the tests of extraction performance, effects of solvent and extraction time on selected BFRs were investigated; toluene and 120 min extraction time were chose as the optimum conditions. Besides, this article examines the influence of temperature on the chromatographic analysis, the optimum temperature parameters were 280 °C and 320 °C for injector and column, respectively. The ASHE‐GCMS method was validated for the analysis of the certified reference material of CRM8110‐a and IRMM310. The limits of detection (LOD) for polymer sample was 0.55‐4.50 μg mL^?1; linearity range from 0.11 to 16 μg mL^?1. The proposed methodology can fully meet the requirement of relational directives.     

Comparison of C18 silica and multi‐walled carbon nanotubes as the adsorbents for the solid‐phase extraction of Chlorpyrifos and Phosalone in water samples using HPLC

A comparison between C₁₈ silica and multi‐walled carbon nanotubes (MWCNTs) in the extraction of Chlorpyrifos and Phosalone in environmental water samples was carried out using HPLC. Parameters affecting the extraction were type and volume of elution solvent, pH and flow rate of sample through the adsorbent. The optimum conditions obtained by C₁₈ cartridge for adsorption of these pesticides were 4 mL dichloromethane as elution solvent, sample pH of 5, flow rate of 1 mL/min, and those for MWCNT cartridge were 3 mL dichloromethane, pH of 5 and flow rate of 10 mL/min, respectively. Optimized mobile phase for separation and determination of these compounds by HPLC was methanol/water (80:20 v/v) with pH=5 (adjusted with phosphate buffer). Under optimal chromatographic and SPE conditions, LOD, linear range and precision (RSD n=8) were 3.03×10^?3, 0.01–5.00 μg/mL and 2.7% for Chlorpyrifos and 4.03×10^?4, 0.01–5.00 μg/mL and 2.3% for Phosalone, in C₁₈ cartridge, respectively. These values for MWCNT were 4.02×10^?6, 0.001–0.500 μg/mL and 1.8% for Chlorpyrifos and 1.02×10^?6, 0.001–0.500 μg/mL and 1.5% for Phosalone, respectively.     

A greener microwave-assisted extraction method for rapid spectroscopic determination of selected metals in river and freshwater sediment certified reference materials

The current study describes development of novel, cost-effective, rapid and greener microwave-assisted extraction (MW-AE) method using diluted hydrogen peroxide (H₂O₂) and 400 µL of concentrated aqua-regia for the extraction of 10 selected metals (Ba, Cr, Cu, Co Fe, Mn, Ni, Pb, V and Zn) in sediment certified reference materials (CRMs), prior to inductively coupled plasma-optical emission spectroscopic analysis. The optimum extraction conditions were achieved when 0.2 g of sediment was extracted with 1 mol L^?1 of H₂O₂ (12.00 mL) and 400 µL of concentrated aqua-regia, at 180°C microwave extraction temperature for 30 min. Accuracy of the proposed MW-AE method was evaluated by using river (LGC6187) and freshwater (CRM015-050) sediment CRMs. Quantitative extraction recoveries of 80–120% in LGC6187 and 74–124% in CRM0150-050 were obtained with acceptable precision (0.4–1.0%). The proposed extraction method has a clear advantage over classical approaches as 1 mol L^?1 H₂O₂ was used instead of notorious acidic mixture (Hydrochloric acid/ nitric acid/ hydrofluoric). The method detection limits (MDLs) of 0.03–0.9 μg g^?1 were obtained for all the investigated metals and were fairly comparable with the MDLs of the published literature reports. Therefore, the proposed MW-AE method can be routinely used for monitoring of metal ions in various river and fresh water sediments.     

The preparation of a certified reference material of polar pesticides in freeze-dried water (CRM 606)

The preparation of a certified reference material of polar pesticides in freeze-dried water is described. The pesticides selected were atrazine, simazine, carbaryl, propanil, linuron, fenamiphos and permethrin which were added to 6000 litres of tap water at 50–80 μg · L^–1 (200–320 μg · L^–1 for permethrin) level in presence of NaCl (2.5 g · L^–1) prior lyophilization. After the freeze-drying process the residue was rehomogenized, filled into amber glass bottles and stored at –20?°C, +4?°C and +20?°C. All pesticides were determined by HPLC/diode array detector, except permethrin which was determined by GC/ECD. The results obtained for atrazine, simazine, carbaryl, propanil, linuron and fenamiphos showed no within- or between-bottle inhomogeneity, however the material was non-homogeneous for permethrin and therefore this was withdrawn from further studies. With respect to the stability for over one year, all pesticides were stable at –20?°C. At +4?°C all pesticides were stable for at least 9 months and at +20?°C the stability was demonstrated only during the first month of storage. The content (mass fractions) of atrazine, simazine, carbaryl, propanil and linuron in freeze-dried water (CRM 606) was certified by an interlaboratory testing and a certification campaign.     

Determination of arsenic by hydride generation with a long absorption cell for atomic absorption spectrometry

A method is described for the determination of arsenic involving hydride generation and atomic absorption spectrometry with an improved long graphite-tube furnace capable of considerably higher temperatures than the conventional quartz-tube heaters. Arsine is generated with sodium tetrahydroborate, held in a nitrogen-cooled trap and then swept with helium into an alumina tube (19 cm long) placed within the graphite furnace. The optimum conditions for determination of arsenic are given. The detection limit is 0.2 ng ml^?1 with RSD of 2–3%. Results for various NBS Standard Reference Materials agreed well with expected values and were as follows: orchard leaves, 10 ± 1 μg g^?1; tomato leaves, 0.28 ± 0.03 μg g^?1; bovine liver, 0.046 ± 0.005 μg g^?1.     

Certification of butyltins and phenyltins in marine sediment certified reference material by species-specific isotope-dilution mass spectrometric analysis using synthesized <Superscript>118</Superscript>Sn-enriched organotin compounds

A new marine sediment certified reference material, NMIJ CRM 7306-a, for butyltin and phenyltin analysis has been prepared and certified by the National Metrological Institute of Japan at the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). Candidate sediment material was collected at a bay near industrial activity in Japan. After air-drying, sieving, and mixing the material was sterilized with γ-ray irradiation. The material was re-mixed and packaged into 250 glass bottles (15 g each) and these were stored in a freezer at −30 °C. Certification was performed by use of three different types of species-specific isotope-dilution mass spectrometry (SSID–MS)—SSID–GC–ICP–MS, SSID–GC–MS, and SSID–LC–ICP–MS, with ¹¹⁸Sn-enriched organotin compounds synthesized from ¹¹⁸Sn-enriched metal used as a spike. The ¹¹⁸Sn-enriched mono-butyltin (MBT), dibutyltin (DBT), and tributyltin (TBT) were synthesized as a mixture whereas the ¹¹⁸Sn-enriched di-phenyltin (DPhT) and triphenyltin (TPhT) were synthesized individually. Four different extraction methods, mechanical shaking, ultrasonic, microwave-assisted, and pressurized liquid extraction, were adopted to avoid possible analytical bias caused by non-quantitative extraction and degradation or inter-conversion of analytes in sample preparations. Tropolone was used as chelating agent in all the extraction methods. Certified values are given for TBT 44±3 μg kg⁻¹ as Sn, DBT 51 ± 2 μg kg⁻¹ as Sn, MBT 67 ± 3 μg kg⁻¹ as Sn, TPhT 6.9 ± 1.2 μg kg⁻¹ as Sn, and DPhT 3.4 ± 1.2 μg kg⁻¹ as Sn. These levels are lower than in other sediment CRMs currently available for analysis of organotin compounds.     

Certification of contents of aromatic hydrocarbons in charcoal tubes – CRM 562

A Certified Reference Material (CRM) for determination of aromatic hydrocarbons in air was developed. The CRM 562 consists of aromatic hydrocarbons sorbed on charcoal in glass tubes. Initial feasibility studies established that a homogeneous and stable batch could be prepared. Three intercomparisons prior to the certification allowed the identification of various sources of error. Then, a batch of about 3000 tubes was charged and certified on the basis of analyses carried out in 15 European laboratories. The preparation of the reference material and the results of the certification exercise is described. An overview on the analytical techniques used and the quality control guidelines are also presented. The certified values are 15.0 ± 0.4 μg benzene, 147.3 ± 3.8 μg toluene, 96.4 ± 2.5 μg m-xylene and 93.0 ± 2.9 μg o-xylene per tube. This reference material is recommended for quality control of measurements in the field of occupational hygiene.     

Simple mercury fractionation in biological samples by CV AAS following microwave-assisted acid digestion or TMAH pre-treatment

A simple and reliable method to determine total and inorganic mercury in biological certified reference material (CRM) by cold vapor atomic absorption spectrometry (CV AAS) is proposed. After the CRM treatment at room temperature with tetramethylammonium hydroxide (TMAH), inorganic mercury is determined by CV AAS. Total mercury is measured by the same technique, after sample acid digestion in a microwave oven. Organic mercury, basically methylmercury, is obtained by difference. In both procedures, the quartz tube is kept at room temperature. By means of analysis of the following reference materials: pig kidney, lobster hepatopancreas, dogfish liver and mussel tissue, it was clear that the difference between the total and inorganic mercury concentrations agrees with the methylmercury concentration. Only one calibration curve against aqueous standards in acidic medium was carried out for both procedures. The concentrations obtained by both procedures are in agreement with the certified values according to the t-test at a 95% confidence level. The relative standard deviations were lower than 3.0% for digested CRM and 6.0% for CRM treated with TMAH for most of the samples. The limits of detection in the samples were 0.02 µg g^− 1 and 0.04 µg g^− 1 for inorganic and total Hg, respectively, since the sample mass for total mercury was half of that for inorganic mercury determination. Simplicity and high efficiency without using chromatographic techniques are some of the qualities of the proposed method, being adequate for fractionation analysis of mercury in biological samples.     

A Screening Method for Polycyclic Aromatic Hydrocarbons Determination in Sediments by Headspace SPME with GC–FID

A screening method for polycyclic aromatic hydrocarbons (PAHs) determination in sediment using headspace solid phase microextraction (HS-SPME) with gas chromatography–flame ionization detection was developed. In order to obtain the convenient experimental conditions for HS-SPME extraction an experimental design with two steps was done. 0.2 g of sediment and 85 µm polyacrylate fibre, 80 °C and 120 min were the chosen extractions conditions. The limit of detection (LOD) was from 0.8 ng g⁻¹ (fluoranthene) to 8 ng g⁻¹ (chrysene). The relative standard deviation (RSD) was less than 7.0%. Determination of PAHs in NRC–CNRC–HS–3B reference marine sediment showed good agreement with the certified values. The method was applied in the analysis of ten river and estuary surface sediments from Gipuzkoa (North Spain). PAHs total concentration ranged from 400 to 5,500 ng g⁻¹.

     

Pervaporation as a Separation Technique for Direct Determination of Volatile Selenium Species by Atomic Fluorescence Spectrometry

Abstract

This paper reports for the first time a suitable way to determine methylated selenium compounds using the new approach of pervaporation coupled to atomic fluorescence spectrcmetry (PV-AFS).

The method developed allows direct extraction, separation, preconcentration and determination of dimethylselenium (DMSe) and dimethyldiselenium (DMDSe) from slurry samples. Under the optimum conditions, the detection limits (LODs) were found to be 0.66 ng and 0.39 ng for DMSe and DMDSe, respectively, the precision being about 6–9 % for 10 ng mL as selenium concentration. The linearity ranges were from the LOD to 0.7 μg mL^?1 for DMSe and from the LOD to 0.4 μg mL^?1 for DMDSe (as Se). The pervaporation efficiencies were 55 ± 1 % and 85 ± 5 % for DMSe and DMDSe, respectively. The proposed method was successfully applied to determine methylated selenium species in sewage sludge, garlic and oyster samples. The concentrations found were from 0.07 to 1.42 μg g^?1.

As no certified reference materials are available for these analytes, validation was carried out by recovery studies in these matrices, and the results showed that the proposed method performed satisfactorily.     

The determination of low lead levels in the bone of lead-depleted mice by graphite furnace atomic absorption spectrometry

Low lead levels in the femurs of mice fed with a lead-depleted diet have been determined by use of electrothermal atomic absorption spectrometry with Zeeman-effect background correction. The method is based on the use of Mg(NO₃)₂/Pd as matrix modifier which enables significant reduction of the spectral interferences prevalent if chemical modifiers based on NH₄H₂PO₄ with either Ca or Mg are used for samples rich in Ca₃(PO₄)₂ matrix. The method was developed and validated by use of the NIST standard reference material 1486 bone. Bones were decomposed in a pressurized microwave-heated system using 70% nitric acid. Forty-three mice femurs, with a mass of 74.62 ± 12.54 mg, were dissolved in concentrated nitric acid. The lead results found in SRM 1486 (1.25 ± 0.15 μg g^–1, n = 9) were in good agreement with the certificate (1.335 ± 0.014 μg g^–1). Recoveries of 200 ng lead added to the SRM before or after digestion were 99.0 ± 1.4% and 98.5 ± 1.6%, respectively. The lead detection limit in bone samples is 0.06 μg g^–1 dry mass. This method is, therefore, suitable for the determination of very low lead levels (0.06–0.20 μg Pb kg^–1 bone) in the femurs of mice fed a diet with lead level of < 20μg kg^–1.     

Efficiency of solvent extraction methods for the determination of methyl mercury in forest soils

Methyl mercury was determined by gas chromatography, microwave induced plasma, atomic emission spectrometry (GC-MIP-AES) using two different methods. One was based on extraction of mercury species into toluene, pre-concentration by evaporation and butylation of methyl mercury with a Grignard reagent followed by determination. With the other, methyl mercury was extracted into dichloromethane and back extracted into water followed by in situ ethylation, collection of ethylated mercury species on Tenax and determination. The accuracy of the entire procedure based on butylation was validated for the individual steps involved in the method. Methyl mercury added to various types of soil samples showed an overall average recovery of 87.5%. Reduced recovery was only caused by losses of methyl mercury during extraction into toluene and during pre-concentration by evaporation. The extraction of methyl mercury added to the soil was therefore quantitative. Since it is not possible to directly determine the extraction efficiency of incipient methyl mercury, the extraction efficiency of total mercury with an acidified solution containing CuSO₄ and KBr was compared with high-pressure microwave acid digestion. The solvent extraction efficiency was 93%. For the IAEA 356 sediment certified reference material, mercury was less efficiently extracted and determined methyl mercury concentrations were below the certified value. Incomplete extraction could be explained by the presence of a large part of inorganic sulfides, as determined by ¶x-ray absorption near-edge structure spectroscopy (XANES). Analyses of sediment reference material CRM 580 gave results in agreement with the certified value. The butylation method gave a detection limit for methyl mercury of 0.1 ng g^–1, calculated as three times the standard deviation for repeated analysis of soil samples. Lower values were obtained with the ethylation method. The precision, expressed as RSD for concentrations 20 times above the detection limit, was typically 5%.     

Determination of Trace Methyl Tert‐Butyl Ether in Water Samples Using Dispersive Liquid‐Liquid Microextraction Coupled with GC‐FID

A rapid and sensitive analytical method has been developed for trace analysis of methyl tert‐butyl ether (MTBE) in water samples using dispersive liquid‐liquid microextraction and gas chromatography with flame ionization detection. Factors relevant to the microextraction efficiency, such as the kind of extraction solvent, the disperser solvent and their volumes, the effect of salt, sample solution temperature and the extraction time were investigated and optimized. Under the optimal conditions the linear dynamic range of MTBE was from 0.2 to 25.0 μg L^?1 with a correlation coefficient of 0.9981 and a detection limit of 0.1 μg L^?1. The relative standard deviation (RSD%) was less than 5.1% (n = 3) and the recovery values were in the range of 97.8 ± 0.9%. Finally, the proposed method was successfully applied for the analysis of MTBE in aqueous samples.