Development and validation of an LC‐MS/MS method for quantification of Δ9‐tetrahydrocannabinolic acid A (THCA‐A), THC,CBN and CBD in hair

For analysis of hair samples derived from a pilot study (‘in vivo’ contamination of hair by sidestream marijuana smoke), an LC‐MS/MS method was developed and validated for the simultaneous quantification of Δ9‐tetrahydrocannabinolic acid A (THCA‐A), Δ9‐tetrahydrocannabinol (THC), cannabinol (CBN) and cannabidiol (CBD). Hair samples were extracted in methanol for 4 h under occasional shaking at room temperature, after adding THC‐D₃, CBN‐D₃, CBD‐D₃ and THCA‐A‐D₃ as an in‐house synthesized internal standard. The analytes were separated by gradient elution on a Luna C18 column using 0.1% HCOOH and ACN + 0.1% HCOOH. Data acquisition was performed on a QTrap 4000 in electrospray ionization‐multi reaction monitoring mode. Validation was carried out according to the guidelines of the German Society of Toxicological and Forensic Chemistry (GTFCh). Limit of detection and lower limit of quantification were 2.5 pg/mg for THCA‐A and 20 pg/mg for THC, CBN and CBD. A linear calibration model was applicable for all analytes over a range of 2.5 pg/mg or 20 pg/mg to 1000 pg/mg, using a weighting factor 1/x. Selectivity was shown for 12 blank hair samples from different sources. Accuracy and precision data were within the required limits for all analytes (bias between ?0.2% and 6.4%, RSD between 3.7% and 11.5%). The dried hair extracts were stable over a time period of one to five days in the dark at room temperature. Processed sample stability (maximum decrease of analyte peak area below 25%) was considerably enhanced by adding 0.25% lecithin (w/v) in ACN + 0.1% HCOOH for reconstitution. Extraction efficiency for CBD was generally very low using methanol extraction. Hence, for effective extraction of CBD alkaline hydrolysis is recommended. Copyright © 2013 John Wiley & Sons, Ltd.     

Determination of naphthalen-1-yl-(1-pentylindol-3-yl)methanone (JWH-018) in mouse blood and tissue after inhalation exposure to 'buzz' smoke by HPLC/MS/MS

The disposition of the cannabimimetic naphthalen‐1‐yl‐(1‐pentylindol‐3‐yl)methanone (JWH‐018) in mice following inhalation of the smoke of the herbal incense product (HIP) ‘Buzz’ is presented. A high‐pressure liquid chromatography with electrospray ionization triple quadrupole mass spectrometer (HPLC/MS/MS) method was validated for the analysis of JWH‐018 in the specimens using deuterated Δ⁹‐tetrahydrocannabinol (d₃‐THC) as the internal standard. JWH‐018 was isolated by cold acetonitrile liquid–liquid extraction. Chromatographic separation was performed on a Zorbaz eclipse XDB‐C₁₈ column. The assay was linear from 1 to 1000 ng/mL. Six C57BL6 mice were sacrificed 20 min after exposure to the smoke of 200 mg ‘Buzz’ containing 5.4% JWH‐018. Specimen concentrations of JWH‐018 were: blood, 54–166 ng/mL (mean 82 ± 42 ng/mL); brain, 316–708 ng/g (mean 510 ± 166 ng/g); and liver, 1370–3220 ng/mL (mean 1990 ± 752 ng/mL). The mean blood to brain ratio for JWH‐018 was 6.8 and ranged from 4.2 to 10.9. After exposure, the responses of the mice were consistent with cannabinoid receptor type 1 activity: body temperatures dropped 7.3 ± 1.1 °C, and catalepsy, hyperreflexia, straub tail and ptosis were observed. The brain concentrations and physiological responses are consistent with the hypothesis that the behavioral effects of ‘Buzz’ are attributable to JWH‐018. Copyright © 2012 John Wiley & Sons, Ltd.     

Simultaneous determination of 75 abuse drugs including amphetamines,benzodiazepines, cocaine,opioids, piperazines,zolpidem and metabolites in human hair samples using liquid chromatography–tandem mass spectrometry

A liquid chromatography–tandem mass spectrometric method for the simultaneous determination of 75 abuse drugs and metabolites, including 19 benzodiazepines, 19 amphetamines, two opiates, eight opioids, cocaine, lysergic acid diethylamide, zolpidem, three piperazines and 21 metabolites in human hair samples, was developed and validated. Ten‐milligram hair samples were decontaminated, pulverized using a ball mill, extracted with 1 mL of methanol spiked with 28 deuterated internal standards in an ultrasonic bath for 60 min at 50°C, and purified with Q‐sep dispersive solid‐phase extraction tubes. The purified extracts were evaporated to dryness and the residue was dissolved in 0.1 mL of 10% methanol. The 75 analytes were analyzed on an Acquity HSS T3 column using gradient elution of methanol and 0.1% formic acid and quantified in multiple reaction monitoring mode with positive electrospray ionization. Calibration curves were linear (r ≥ 0.9951) from the lower limit of quantitation (2–200 pg/mg depending on the drug) to 2000 pg/mg. The coefficients of variation and accuracy for intra‐ and inter‐assay analysis at three QC levels were 4.3–12.9% and 89.2–109.1%, respectively. The overall mean recovery ranged from 87.1 to 105.3%. This method was successfully applied to the analysis of 11 forensic hair samples obtained from drug abusers.     

Investigations on the influence of different grinding procedures on measured ethyl glucuronide concentrations in hair determined with an optimized and validated LC-MS/MS method

Ethyl glucuronide (EtG) analysis in hair is a suitable method for the retrospective determination of previous alcohol consumption. According to the German guidelines, EtG abstinence is improbable at c _EtG > 7 pg/mg in the proximal 3 cm of scalp hair. The chromatography of the routinely used liquid chromatography-tandem mass spectrometry procedure was optimized by replacing the stationary phase. To simplify sample preparation, two different mills were tested, and an optimized grinding process was developed. The new method was successfully validated according to the guidelines of the German Society of Toxicological and Forensic Chemistry. Despite a simple extraction procedure without any cleaning steps, a very high sensitivity (limit of detection, 1.7 pg/mg; limit of quantitation, 2.3 pg/mg) could be achieved. Competitive analysis showed significantly higher EtG concentrations in pulverized versus cut hair samples. The strong impact of sample preparation on the determined EtG concentrations suggests the introduction of a standardized sample preparation method to produce comparable results.     

Analysis of 30 synthetic cannabinoids in serum by liquid chromatography‐electrospray ionization tandem mass spectrometry after liquid‐liquid extraction

The analysis of synthetic cannabinoids in human matrices is of particular importance in the fields of forensic and clinical toxicology since cannabis users partly shift to the consumption of ‘herbal mixtures’ as a legal alternative to cannabis products in order to circumvent drug testing. However, comprehensive methods covering the majority of synthetic cannabinoids already identified on the drug market are still lacking. In this article, we present a fully validated method for the analysis of 30 synthetic cannabinoids in human serum utilizing liquid‐liquid extraction and liquid chromatography‐electrospray ionization tandem mass spectrometry. The method proved to be suitable for the quantification of 27 substances. The limits of detection ranged from 0.01 to 2.0 ng/mL, whereas the lower limits of quantification were in the range from 0.1 to 2.0 ng/mL. The presented method was successfully applied to 833 authentic serum samples during routine analysis between August 2011 and January 2012. A total of 227 (27%) samples was tested positive for at least one of the following synthetic cannabinoids: JWH‐018, JWH‐019, JWH‐073, JWH‐081, JWH‐122, JWH‐200, JWH‐203, JWH‐210, JWH‐307, AM‐2201 and RCS‐4. The most prevalent compounds in positive samples were JWH‐210 (80%), JWH‐122 (63%) as well as AM‐2201 (29%). Median serum concentrations were all below 1.0 ng/mL. These findings demonstrate a significant shift of the market of synthetic cannabinoids towards substances featuring a higher CB₁ binding affinity and clearly emphasize that the analysis of synthetic cannabinoids in serum or blood samples requires highly sensitive analytical methods covering a wide spectrum of substances. Copyright © 2012 John Wiley & Sons, Ltd.     

Novel mode of liquid‐phase microextraction: A magnetic stirrer as the extractant phase holder

In the present study, a novel configuration of liquid‐phase microextraction was proposed, in which a magnetic stirrer with a groove was used as the extractant phase holder. It was termed as magnetic stirrer liquid‐phase microextraction. In this way, the stability of the organic solvent was much improved under high stirring speed; the extraction efficiency was enhanced due to the enormously enlarged contact area between the organic solvent and aqueous phase. The extraction performance of the magnetic stirrer liquid‐phase microextraction was studied using chlorobenzenes as the probe analytes. A wide linearity range (20 pg/mL to 200 ng/mL) with a satisfactory linearity coefficient (r² > 0.998) was obtained. Limits of detection ranged from 9.0 to 12.0 pg/mL. Good reproducibility was achieved with intra‐ and inter‐day relative standard deviations <4.8%. The proposed magnetic stirrer liquid‐phase microextraction was simple, environmentally friendly and efficient; compared to single‐drop microextraction, it had obvious advantages in terms of reproducibility and extraction efficiency. It is a promising miniaturized liquid‐phase technology for real applications.     

Simultaneous determination of morphine,codeine, 6‐acetylmorphine,cocaine and benzoylecgonine in hair by liquid chromatography/electrospray ionization tandem mass spectrometry

A fast and sensitive liquid chromatography/triple quadrupole tandem mass spectrometry (LC/MS/MS) method was developed for the simultaneous determination of morphine, codeine, 6‐acetylmorphine (6‐AM), cocaine and benzoylecgonine (BE) in hair. Pulverized hair samples were extracted with methanol, and a 50 µL supernatant aliquot was injected into the LC/MS/MS system. Chromatography was performed with an XBridge? phenyl column (3.5 µm particle size, 4.6 × 150 mm), and the mobile phase was composed of methanol and 10 mM ammonium acetate adjusted to pH 4.00 with 99% formic acid (95:5, v/v). A separation run with isocratic elution was completed in 10 min at a flow rate of 500 µL/min. Positive electrospray ionization and multiple reaction monitoring (MRM) with one precursor ion/product ion transition were used for the identification of each analyte. Deuterated analogues as internal standards were used for quantification and qualification. Linearity was established in the concentration range of 100–3000 pg/mg. The limits of detection were 10 pg/mg for morphine, codeine and 6‐AM; and 1 pg/mg for cocaine and BE. The precision and accuracy were determined by spiking hair samples at six concentration levels. For all analytes, the relative standard deviations of intra‐ and inter‐day precision were 0.1–6.3% and 1.5–10.6%, respectively. The accuracy ranged from 92.7 to 109.7%. The validated LC/MS/MS method was successfully applied to the analysis of 79 authentic hair samples. Copyright © 2009 John Wiley & Sons, Ltd.     

Simple and rapid determination of N6‐(Δ2‐isopentenyl)adenine,zeatin, and dihydrozeatin in plants using on‐line cleanup liquid chromatography coupled with hybrid quadrupole‐Orbitrap high‐resolution mass spectrometry

A simple and rapid method was developed for the determination of three free cytokinins, namely, N⁶‐(Δ²‐isopentenyl)adenine, zeatin, and dihydrozeatin, in plants using TurboFlow on‐line cleanup liquid chromatography combined with hybrid quadrupole‐Orbitrap high‐resolution mass spectrometry. The samples were extracted using acetonitrile, and then the extract was purified on a C₁₈‐p column, in which the sample matrix was removed and the analytes were retained. Subsequently, the analytes were eluted from the extraction column onto the analytical column (Hypersil Gold C₁₈ column) prior to chromatographic separation and hybrid Q‐Orbitrap detection using the targeted‐MS² scan mode. The linearity was satisfactory with a correlation coefficient of >0.999 at concentrations ranging from 5–5000 pg/mL. The limits of quantification for the analytes ranged from 4.2–5.2 pg/mL. The intra‐ and inter‐day average recoveries of analytes fortified at three levels ranged from 85.4–108.2%, and the intra‐ and inter‐day relative standard deviations ranged from 4.04–8.57%. The method was successfully applied for the determination of free cytokinins in different tissue samples of Oryza sativa and Arabidopsis thaliana.     

Simultaneous LC-HRMS determination of 28 benzodiazepines and metabolites in hair

A liquid chromatography–high resolution mass spectrometry (LC-HRMS) method for the simultaneous identification and quantification of 28 benzodiazepines, including 6 metabolites, in 50 mg of hair has been validated. Positive ion electrospray ionization and HRMS determination in full-scan mode were realized on an Orbitrap mass spectrometer at a nominal resolving power of 60,000. In-source collisional experiments were conducted to obtain additional information for a more reliable identification of the investigated drugs. HRMS in full-scan mode allowed the exact determination of molecular masses of all analytes eluting in the HPLC run, so that both the immediate and retrospective screening of results for drugs and their metabolites were available. Sample preparation consisted of an overnight incubation in phosphate buffer pH 8.4 and a subsequent liquid/liquid extraction with methylene chloride/diethyl ether (90:10). Gradient elution was performed on a Luna C18 analytical column and four deuterated analogues were used as internal standards (IS). Validation was performed using both spiked hair samples and hair samples from subjects treated with benzodiazepines. Selectivity was evaluated by analysis of 20 certified blank hair samples. Extraction efficiency and matrix effects were evaluated by analysis of true positive samples. The lowest limits of quantification (LLOQs) ranged from 1 to 10 pg/mg. Linearity was investigated in the range from LLOQ to 1,000 pg/mg, for each compound (R ² 0.998–0.999). Mean relative errors, calculated at three concentration levels, ranged from 1 to 20% (absolute value). Precision, at concentrations higher than the LLOQs, was always less than 15% expressed as percentage relative standard deviation. After validation, the procedure was applied to real samples collected for clinical and forensic toxicology purposes from subjects who were assumed to have taken benzodiazepines.     

Can JWH‐210 and JWH‐122 be detected in adipose tissue four weeks after single oral drug administration to rats?

Synthetic cannabinoids such as alkylindole derivatives entered the illicit drug market worldwide a few years ago. Only a few data are available concerning their pharmacokinetics, in particular their distribution and persistence in adipose tissue. For the present study, rats were administered a single 20 mg/kg oral dose of JWH‐210 or JWH‐122. After one month, they were dissected and adipose tissue was taken in order to study whether JWH‐210 and JWH‐122 persisted in this body sample. After extraction, the samples were analyzed by liquid chromatographic–mass spectrometry (LC‐QTrap‐MS). Validation of the analytical method for adipose tissue is also presented. The results of the matrix effects determination ranged between 30.6 and 43.8%. The limits of detection for JWH‐210 and JWH‐122 were 0.8 and 1.0 ng/g and lower limits of quantification were 3.7 and 2.1 ng/g, respectively. Calibration curves ranged from 10 to 75 ng/g for JWH‐210 and from 5 to 50 ng/g for JWH‐122. Intra‐ and interday precision values were lower than 15% and bias values within ±15%. Applying this method, in adipose tissue specimens obtained 4 weeks after single drug administration, JWH‐210 and JWH‐122 were detected in concentrations of 116 and 9 ng/g, respectively. Copyright © 2014 John Wiley & Sons, Ltd.     

Characteristics of the designer drug and synthetic cannabinoid receptor agonist AM‐2201 regarding its chemistry and metabolism

Aminoalkylindoles, a subclass of synthetic cannabinoid receptor agonists, show an extensive and complex metabolism in vivo, and due to their structural similarity, they can be challenging in terms of unambiguous assignment of metabolic patterns in urine samples to consumed substances. The situation may even be more complicated as these drugs are usually smoked, and the high temperature exposure may lead to formation of artifacts. Typical metabolites of JWH‐018 (Naphthalen‐1‐yl(1‐pentyl‐1H‐indol‐3‐yl)methanone) were reportedly detected not only in urine samples collected after consumption of JWH‐018 but also after AM‐2201 (1‐(5‐fluoropentyl‐1H‐indol‐3‐yl)‐(naphthalene‐1‐yl)methanone) use. The aim of the presented study was to evaluate if typical JWH‐018 metabolites can be formed metabolically in humans and if JWH‐018 may be formed artifactually during smoking of AM‐2201. Therefore, one of the authors ingested 5 mg of pure AM‐2201, and serum as well as urine samples were analyzed subsequently. Additionally, the smoke condensate from a cigarette laced with pure AM‐2201 was investigated. In addition, urine samples of patients after known consumption of AM‐2201 or JWH‐018 were evaluated. The results of the study prove that typical metabolites of JWH‐018 and JWH‐073 are built in humans after ingestion of AM‐2201. However, the N‐(4‐hydroxypentyl) metabolite of JWH‐018, which is the major metabolite after JWH‐018 use, was not detected after the self‐experiment. In the smoke condensate, small amounts of JWH‐018 and JWH‐022 (Naphthalen‐1‐yl[1‐(pent‐4‐en‐1‐yl)‐1H‐indol‐3‐yl]methanone) were detected. Nevertheless, the results of our study suggest that the amounts absorbed by smoking do not significantly influence the metabolic pattern in urine samples. Therefore, the N‐(4‐hydroxypentyl) metabolite of JWH‐018 can serve as a valuable marker to distinguish consume of products containing AM‐2201 from JWH‐018 use. Copyright © 2013 John Wiley & Sons, Ltd.     

Quadrupole‐time‐of‐flight mass spectrometry screening for synthetic cannabinoids in herbal blends

‘Legal highs’ are novel substances which are intended to elicit a psychoactive response. They are sold from ‘head shops’, the internet and from street suppliers and may be possessed without legal restriction. Several months ago, a 19‐year‐old woman came searching for medical treatment as she had health problems caused by smoking legal highs. The substances were sold as herbal blends in plastic bags under four different labels. In this work, samples of these herbal blends have been analysed to investigate the presence of psychoactive substances without any reference standard being available at the laboratory. A screening strategy for a large number of synthetic and natural cannabinoids has been applied based on the use of ultra‐high pressure liquid chromatography coupled to quadrupole‐time of flight mass spectrometry (UHPLC‐QTOF MS) under MS^E mode. A customized home‐made database containing literature‐based exact masses for parent and product ions of around 200 synthetic and natural cannabinoids was compiled. The presence of the (de)protonated molecule measured at its accurate mass was evaluated in the samples. When a peak was detected, collision‐induced dissociation fragments and characteristic isotopic ions were also evaluated and used for tentative identification. After this tentative identification, four synthetic cannabinoids (JWH‐081, JWH‐250, JWH‐203 and JWH‐019) were unequivocally confirmed by subsequent acquisition of reference standards. The presence in the herbal blends of these synthetic cannabinoids might explain the psychotic and catatonic symptoms observed in the patient, as JWH compounds could act as potent agonists of CB₁ and CB₂ receptors located in the Limbic System and Basal ganglia of the human brain. Copyright © 2013 John Wiley & Sons, Ltd.     

Development and validation of a rapid ultra high performance liquid chromatography with tandem mass spectrometry method for the simultaneous determination of darunavir,ritonavir, and tenofovir in human plasma: Application to human pharmacokinetics

A sensitive ultra high performance liquid chromatography with tandem mass spectrometry method was developed for the simultaneous determination of darunavir, ritonavir and tenofovir in human plasma. Sample preparation involved a simple liquid–liquid extraction using 200 μL of human plasma extracted with methyl tert‐butyl ether for three analytes and internal standard. The separation was accomplished on an Acquity UPLC BEH C₁₈ (50 mm x 2.1 mm, 1.7 μm) analytical column using gradient elution of acetonitrile/methanol (80:20, v/v) and 5.0 mM ammonium acetate containing 0.01% formic acid at a flow rate of 0.4 mL/min. The linearity of the method ranged between 20.0 and 12 000 ng/mL for darunavir, 2.0 and 2280 ng/mL for ritonavir, and 14.0 and 1600 ng/mL for tenofovir using 200 μL of plasma. The method was completely validated for its selectivity, sensitivity, linearity, precision and accuracy, recovery, matrix effect, stability, and dilution integrity. The extraction recoveries were consistent and ranged between 79.91 and 90.04% for all three analytes and internal standard. The method exhibited good intra‐day and inter‐day precision between 1.78 and 6.27%. Finally the method was successfully applied for human pharmacokinetic study in eight healthy male volunteers after the oral administration of 600 mg darunavir along with 100 mg ritonavir and 100 mg tenofovir as boosters.     

Quantification of testosterone undecanoate in human hair by liquid chromatography–tandem mass spectrometry

Testosterone undecanoate (T‐C11) can be used by athletes in order to improve performance. After oral intake, T‐C11 is rapidly metabolized, hampering discrimination between exogenous and endogenous testosterone. A possible alternative is to detect the intact ester in hair. A method based on liquid chromatography–tandem mass spectrometry was developed for the determination of T‐C11 in hair. The sample procedure consisted of digestion of 200 mg of pulverized hair with tris(2‐carboxyethyl)phosphine hydrochloride and liquid–liquid extraction with n‐pentane. Several parameters such as the mobile phase, the ionization source and the washing step were optimized. The method was validated at different spiked levels obtaining satisfactory values for accuracy (between 92 and 102%) with relative standard deviations lower than 7% and a limit of detection of 0.2 ng/g. The applicability of the method was checked by the analysis of three samples from patients using T‐C11. A peak for the analyte was detected in all samples with concentrations between 0.4 and 8.4 ng/g. Copyright © 2009 John Wiley & Sons, Ltd.     

Direct screening of herbal blends for new synthetic cannabinoids by MALDI‐TOF MS

Since 2004, a number of herbal blends containing different synthetic compounds mimicking the pharmacological activity of cannabinoids and displaying a high toxicological potential have appeared in the market. Their availability is mainly based on the so‐called “e‐commerce”, being sold as legal alternatives to cannabis and cannabis derivatives. Although highly selective, sensitive, accurate, and quantitative methods based on GC–MS and LC–MS are available, they lack simplicity, rapidity, versatility and throughput, which are required for product monitoring. In this context, matrix‐assisted laser desorption ionization‐time of flight mass spectrometry (MALDI‐TOF MS) offers a simple and rapid operation with high throughput. Thus, the aim of the present work was to develop a MALDI‐TOF MS method for the rapid qualitative direct analysis of herbal blend preparations for synthetic cannabinoids to be used as front screening of confiscated clandestine preparations. The sample preparation was limited to herbal blend leaves finely grinding in a mortar and loading onto the MALDI plate followed by addition of 2 µl of the matrix/surfactant mixture [α‐cyano‐4‐hydroxy‐cinnamic acid/cetyltrimethylammonium bromide (CTAB)]. After drying, the sample plate was introduced into the ion source for analysis. MALDI‐TOF conditions were as follows: mass spectra were analyzed in the range m/z 150–550 by averaging the data from 50 laser shots and using an accelerating voltage of 20 kV. The described method was successfully applied to the screening of 31 commercial herbal blends, previously analyzed by GC–MS. Among the samples analyzed, 21 contained synthetic cannabinoids (namely JWH‐018, JWH‐073, JWH‐081, JWH‐250, JWH‐210, JWH‐019, and AM‐694). All the results were in agreement with GC–MS, which was used as the reference technique. Copyright © 2012 John Wiley & Sons, Ltd.     

Sensitive quantification of coixol,a potent insulin secretagogue,in Scoparia dulcis extract using high‐performance liquid chromatography combined with tandem mass spectrometry and UV detection

Diabetes is a major global health problem which requires new studies for its prevention and control. Scoparia dulcis , a herbal product, is widely used for treatment of diabetes. Recent studies demonstrate coixol as a potent and nontoxic insulin secretagog from S. dulcis . This study focuses on developing two quantitative methods of coixol in S. dulcis methanol‐based extracts. Quantification of coixol was performed using high‐performance liquid chromatography–tandem mass spectrometry (method 1) and high‐performance liquid chromatography–ultraviolet detection (method 2) with limits of detection of 0.26 and 11.6 pg/μL, respectively, and limits of quantification of 0.78 and 35.5 pg/μL, respectively. S. dulcis is rich in coixol content with values of 255.5 ± 2.1 mg/kg (method 1) and 220.4 ± 2.9 mg/kg (method 2). Excellent linearity with determination coefficients >0.999 was achieved for calibration curves from 10 to 7500 ng/mL (method 1) and from 175 to 7500 ng/mL (method 2). Good accuracy (bias < −8.6%) and precision (RSD < 8.5%) were obtained for both methods. Thus, they can be employed to analyze coixol in plant extracts and herbal formulations.     

Vortex‐assisted surfactant‐enhanced‐emulsification liquid–liquid microextraction of biogenic amines in fermented foods before their simultaneous analysis by high‐performance liquid chromatography

A simple, rapid, sensitive, and environmentally friendly method, based on modified dispersive liquid–liquid microextraction coupled with high‐performance liquid chromatography was developed for the simultaneous determination of five biogenic amines in fermented food samples. Biogenic amines were derivatized with 9‐fluorenylmethyl chloroformate, extracted by vortex‐assisted surfactant‐enhanced emulsification liquid–liquid microextraction, and then analyzed by high‐performance liquid chromatography. Five biogenic amine compounds were separated within 30 min using a C₁₈ column and gradient elution with acetonitrile and 1% acetic acid. Factors influencing the derivatization and extraction efficiency such as type and volume of extraction solvent, type, and concentration of surfactant, pH, salt addition, and vortex time were optimized. Under the optimum conditions, the method provided the enrichment factors in the range of 161–553. Good linearity was obtained from 0.002–0.5 mg/L for cadaverine and tyramine, 0.003–1 mg/L for tryptamine and histamine, and 0.005–1 mg/L for spermidine with coefficient of determination (R²) > 0.992. The limits of detection ranged from 0.0010 to 0.0026 mg/L. The proposed method was successfully applied to analysis of biogenic amines in fermented foods such as fermented fish (plaa‐som), wine and beer where good recoveries were obtained in the range of 83.2–112.5%     

Dual‐column capillary microextraction (CME) combined with electrothermal vaporization inductively coupled plasma mass spectrometry (ETV‐ICP‐MS) for the speciation of arsenic in human hair extracts

In this work, dual‐column capillary microextraction (CME) system consisting of N‐(2‐aminoethyl)‐3‐aminopropyltrimethoxysilane (AAPTS)‐silica coated capillary (C1) and 3‐mercaptopropyl trimethoxysilane (MPTS)‐silica coated capillary (C2) was developed for sequential separation/preconcentration of arsenite [As(III)], arsenate [As(V)], monomethylarsonic acid [MMA(V)] and dimethylarsinic acid [DMA(V)] in the extracts of human hair followed by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV‐ICP‐MS) detection with iridium as permanent modifier. Various experimental parameters affecting the dual‐column microextraction of different As species had been investigated in detail. It was found that at pH 9, As(V) and MMA could be quantitatively retained by C1 and only As(III) could be quantitatively retained by C2. With the aid of valve switching, As(V)/MMA(V) retained on C1 and As(III) retained on C2 could be sequentially desorbed by 10 µl of 0.01 mol l^?1 HNO₃ [for As(V)], 0.1 mol l^?1 HNO₃ [for MMA(V)] and 0.2 mol l^?1 HNO₃‐3% thiourea (m/v) [for As(III)], respectively, the eluents were immediately introduced into the Ir‐coated graphite tubes for further ETV‐ICP‐MS detection. With two‐step ETV pyrolysis program, Cl^? in the sample matrix could be in situ removed, and the total As in the human hair extracts or digested solution could be interference‐free, determined by ETV‐ICP‐MS. DMA(V) in the human hair extracts was obtained by subtraction of total As in the human hair extracts from other three As species. Under the optimized conditions, the detection limits (3 σ) of the method were 3.9 pg ml^?1 for As(III), 2.7 pg ml^?1 for As(V), 2.6 pg ml^?1 for MMA(V) and 124 pg ml^?1 for total As with the relative standard deviations less than 7.0% (C = 0.1 ng ml^?1, n = 7), and the enrichment factor was 286, 262 and 260 for As(III), As(V) and MMA(V), respectively. The developed method was successfully applied for the speciation of arsenic in the extracts of human hair. Copyright © 2009 John Wiley & Sons, Ltd.     

Development and validation of GC/MS method for determination of pramipexole in rat plasma

A simple, rapid and sensitive method has been developed and validated for the determination of pramipexole in rat plasma by using gas chromatography mass spectrometry. The lower limit of quantification (LLOQ) is superior to the other reported LC‐MS/MS methods. After being made alkaline with NaOH, plasma samples (0.1 mL) were subjected to liquid–liquid exteraction using methyl‐t‐butyl ether. Analytes were determined using electron impact ionization in a single quadrupole mass spectrometer. GC/MS was performed in the selected ion monitoring mode using target ions at m/z 211, 212 and 152 for pramipexole and m/z 194 and 165 for caffeine as internal standard. A linear calibration curve was plotted over the range of 20–1000 pg/mL for pramipexole (r² > 0.996). The LLOQ was 20.0 pg/mL, respectively, which offered high sensitivity and selectivity enough for bioanalytical investigation. Inter‐ and intraday precisions ranged from 0.3 to 8.8% and from 0.9 to 11.33%, respectively. The recovery of pramipexole from plasma ranged from 82.4 ± 7.1 to 87.8 ± 5.7%. The method fulfills all standards required for bioanalytical methods and can be successfully applied to a pharmacokinetic study of pramipexole in rats. Copyright © 2010 John Wiley & Sons, Ltd.     

Determination of polychlorinated biphenyls by liquid chromatography–atmospheric pressure photoionization–mass spectrometry

This study presents the atmospheric pressure photoionization (APPI) of high‐chlorinated (five or more chlorine atoms) polychlorinated biphenyls (PCBs) using toluene as dopant, after liquid chromatographic separation. Mass spectra of PCB 101, 118, 138, 153, 180, 199, 206 and 209 were recorded by using liquid chromatography‐APPI‐tandem mass spectrometry (LC‐APPI‐MS/MS) in negative ion full scan mode. Intense peaks appeared at m/z that correspond to [M ? Cl + O]^? ions, where M is the analyte molecule. Furthermore, a detailed strategy, which includes designs of experiments, for the development and optimization of LC‐APPI‐MS/MS methods is described. Following this strategy, a sensitive and accurate method with low instrumental limits of detection, ranging from 0.29 pg for PCB 209 to 8.3 pg for PCB 101 on column, was developed. For the separation of the analytes, a Waters XSELECT HSS T3 (100 mm × 2.1 mm, 2.5 µm) column was used with methanol/water as elution system. This method was applied for the determination of the above PCBs in water samples (surface water, tap water and treated wastewater). For the extraction of PCBs from water samples, a simple liquid–liquid extraction with dichloromethane was used. Method limits of quantification, ranged from 4.8 ng l^?1, for PCB 199, to 9.4 ng l^?1, for PCB 180, and the recoveries ranged from 73%, for PCB 101, to 96%, for PCB 199. The estimated analytical figures were appropriate for trace analysis of high‐chlorinated PCBs in real samples. Copyright © 2014 John Wiley & Sons, Ltd.