Synthesis,characterization, and drug release behaviors of a novel thermo‐sensitive poly(N‐acryloylglycinates)

In this study, a novel thermo‐sensitive poly(N‐acryloylglycinates) was prepared in order to get a potential drug release carrier. The corresponding monomers and the polymers were characterized with Fourier‐transform infrared (FTIR) and ¹H NMR. The thermo‐sensitivity of the poly(N‐acryloylglycinates) was evaluated by measuring their lower critical solution temperatures (LCST) in water, inorganic salt solution, and different pH solutions. The results indicated that poly(N‐acryloylglycine methyl ester) (NAGME) and poly(N‐acryloylglycine ethyl ester) (NAGEE) exhibit a reversible thermo‐sensibility in their aqueous solutions at 61.5 and 12.5°C, respectively. However, no thermo‐sensitive behavior of poly(N‐acryloylglycine propyl ester) (NAGPE) was found due to its over hydrophobicity. The swelling studies on hydrogels were carried out at different temperatures, in different pH, and inorganic salt solutions. The hydrogels showed a remarkable phase transition at about 35°C with changing temperature. The release rate of caffeine from the thermo‐sensitive hydrogel was apparently decreased as the crosslinker content increased and temperature decreased. Seventy five percent caffeine from the polymeric hydrogel with 5% NMBA (N, N‐methylenebis(acrylamide)) was released at room temperature within 240 min, whereas 95.4% caffeine diffused into the medium at 37°C. Copyright © 2009 John Wiley & Sons, Ltd.     

A novel method to prepare temperature/pH‐sensitive poly(N,N‐diethylacrylamide‐co‐acrylic acid) hydrogels with rapid swelling/deswelling behaviors

Fast responsive temperature‐ and pH‐sensitive hydrogels of poly(N,N‐diethylacrylamide‐co‐acrylic acid) (P(DEA‐co‐AA)) have been synthesized successfully by a two‐step procedure, in which the initial polymerization was conducted at constant temperature for 15 min, followed by further polymerization at ?30°C for 12 hr. Swelling studies showed that hydrogels thus prepared had almost the same temperature and pH sensitivity compared with the conventional ones (polymerized at 24°C for 12 hr). However, hydrogels thus prepared had faster swelling/deswelling rates in distilled water than the conventional ones, and their deswelling rates in low pH buffer solutions were also faster than the conventional ones. These improved properties were attributed to the porous network structure, which was confirmed by the results of scanning electron microscopy. Copyright © 2009 John Wiley & Sons, Ltd.     

pH‐triggerable and ultraviolet‐triggerable β‐cyclodextrin microgel

β‐Cyclodextrin (βCD) microgels were prepared water in oil emulsion, and cinnamic acid (CA) was loaded in the microgel by inclusion complexation. The specific loading of CA in the microgel was 0.0203 mg/mg, and it was less than that the calculated specific loading (0.0368 mg/mg). The maximum swelling ratio of CA‐loaded βCD microgel (CAβCD microgel) decreased from 233.9% to 225.7% upon the irradiation of ultraviolet light (λ = 365 nm). And the 5(6)‐carboxyfluorescein release of CAβCD microgel, observed for 12 h, was suppressed upon the irradiation of ultraviolet light, possibly because the microgel can be photocross‐linked, and its mass transfer resistance against dye diffusion would increase. The swelling ratio of CAβCD microgel somewhat depended on the pH value of the medium, possibly because electrostatic repulsion can be developed within the microgel by the ionizable carboxylic group of CA. The 5(6)‐carboxyfluorescein release degree in 12 h of CAβCD microgel increased from 10.5% to 85.1% when the pH value increased from 3.0 to pH 9.0. This is mainly because CA is more soluble at a higher pH value. In the full range of pH value tested, the release degrees of CAβCD microgel were slightly higher than those of βCD microgel, possibly because of the electrostatic repulsion developed within the CAβCD microgel. Copyright © 2014 John Wiley & Sons, Ltd.     

Photo‐induced polymerization of methyl methacrylate/cyclodextrin complex in aqueous solution

Polymerization of hydroxypropyl‐β‐cyclodextrin (HP‐β‐CD) complex of methyl methacrylate (MMA) (MMA/HP‐β‐CD) was carried out under UV irradiation in aqueous solution with Irgacure 2959 (4‐(2‐hydroxyethoxy)phenyl‐(2‐hydroxy‐2‐propyl)ketone) as a photoinitiator at room temperature. The effects of some principal factors, including UV irradiation intensity, initiator concentration, and the ratio of HP‐β‐CD to MMA, on the polymerization were investigated in detail. Compared to the corresponding thermal polymerization, photo‐induced polymerization of the MMA/HP‐β‐CD complex could be accomplished at a higher speed; the polymerization conversion in photo‐induced polymerization reached 94% within 30 min, while it was only 62% for the thermal polymerization of 16 hr at 70°C. The number‐average molecular weight (M_n) and polymerization conversion decreased with the increase in UV intensity and initiator concentration. The resulting PMMA precipitated spontaneously from the solution during polymerization in the absence of any precipitator. About 95 wt% of the HP‐β‐CD remained in the solution after polymerization and the reusability of the residual HP‐β‐CD was experimentally demonstrated. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis,characterization, and evaluation of enzymatically degradable poly(N‐isopropylacrylamide‐co‐acrylic acid) hydrogels for colon‐specific drug delivery

The enzymatically degradable poly(N‐isopropylacrylamide‐co‐acrylic acid) hydrogels were prepared using 4,4^′‐bis(methacryloylamino)azobenzene (BMAAB) as the crosslinker. It was found that the incorporated N‐isopropylacrylamide (NIPAAm) monomer did not change the enzymatic degradation of hydrogel, but remarkably enhanced the loading of protein drug. The hydrogels exhibited a phase transition temperature between 4°C (refrigerator temperature) and 37°C (human body temperature). Bovine serum albumin (BSA) as a model drug was loaded into the hydrogels by soaking the gels in a pH 7.4 buffer solution at 4°C, where the hydrogel was in a swollen status. The high swelling of hydrogels at 4°C enhanced the loading of BSA (loading capability, ca. 144.5 mg BSA/g gel). The drug was released gradually in the pH 7.4 buffer solution at 37°C, where the hydrogel was in a shrunken state. In contrast, the enzymatic degradation of hydrogels resulted in complete release of BSA in pH 7.4 buffer solution containing the cecal suspension at 37°C (cumulative release: ca. 100 mg BSA/g gel after 4 days). Copyright © 2008 John Wiley & Sons, Ltd.     

Kinetics of hexene‐1 polymerization using [(N,N′‐diisopropylbenzene)‐2,3‐(1,8‐napthyl)‐1,4‐diazabutadiene] dibromonickel/methylaluminoxane catalyst system

Kinetics of hexene‐1 polymerization was investigated using [(N,N′‐diisopropylbenzene)2,3‐(1,8‐napthly)‐1,4‐diazabutadiene]dibromonickel/methylaluminoxane catalyst. Experiments were performed at varying catalyst and monomer concentrations in the temperature range of ?10 to 35 °C. First order time‐conversion plot shows a downward curvature at temperatures of 20 °C and 35 °C indicating the presence of finite termination reactions. A nonlinear plot of degree of polymerization (P_n) with respect to conversion indicates occurrence of transfer reactions and slow initiation. The experimental molar masses are higher than predicted, which implies that a fraction of catalyst species could not be activated or is deactivated at the early stages of the reactions. The efficiency of the catalyst (Cat_eff) varies from 0.77 to 0.89. The observed polydispersity of the poly(hexene‐1) s is in the range of 1.18–1.48. The reaction order was found to be 1.11 with respect to catalyst. The Arrhenius plot obtained using the overall propagation rate constant, k_p, at five different temperatures (?10, 0, 10, 20, and 35 °C) was found to be linear with an activation energy, E_a = 4.3 kcal/mol. Based on the results presented it is concluded that the polymerization of hexene‐1 under the above‐mentioned conditions shows significant deviation from ideal “living” behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1093–1100, 2007     

Anionic polymerization of N,N‐dialkyl‐2‐methylenebut‐3‐enamide: Effect of alkyl substituents on polymerization behavior

Anionic polymerizations of three 1,3‐butadiene derivatives containing different N,N‐dialkyl amide functions, N,N‐diisopropylamide (DiPA), piperidineamide (PiA), and cis‐2,6‐dimethylpiperidineamide (DMPA) were performed under various conditions, and their polymerization behavior was compared with that of N,N‐diethylamide analogue (DEA), which was previously reported. When polymerization of DiPA was performed at ?78 °C with potassium counter ion, only trace amounts of oligomers were formed, whereas polymers with a narrow molecular weight distribution were obtained in moderate yield when DiPA was polymerized at 0 °C in the presence of LiCl. Decrease in molecular weight and broadening of molecular weight distribution were observed when polymerization was performed at a higher temperature of 20 °C, presumably because of the effect of ceiling temperature. In the case of DMPA, no polymer was formed at 0 °C and polymers with relatively broad molecular weight distributions (M_w/M_n = 1.2) were obtained at 20 °C. The polymerization rate of PiA was much faster than that of the other monomers, and poly(PiA) was obtained in high yield even at ?78 °C in 24 h. The microstructure of the resulting polymers were exclusively 1,4‐ for poly(DMPA), whereas 20–30% of the 1,2‐structure was contained in poly(DiPA) and poly(PiA). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3714–3721, 2010     

Synthesis and NMR characterization of 6‐Phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose

Cellulose ( 1 ) was converted for the first time to 6‐phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 6 ) in 33% overall yield. Intermediates in the five‐step conversion of 1 to­ 6 were: 6‐O‐tritylcellulose ( 2 ), 6‐O‐trityl‐2,3‐di‐O‐methylcellulose ( 3 ), 2,3‐di‐O‐methylcellulose ( 4 ); and 6‐bromo‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 5 ). Elemental and quantitative carbon‐13 analyses were concurrently used to verify and confirm the degrees of substitution in each new polymer. Gel permeation chromotography (GPC) data were generated to monitor the changes in molecular weight (DP_w) as the synthesis progressed, and the compound average decrease in cellulose DP_w was ～ 27%. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to characterize the decomposition of all polymers. The degradation temperatures ( °C) and percent char at 500 °C of cellulose derivatives 2 to 6 were 308.6 and 6.3%, 227.6 °C and 9.7%, 273.9 °C and 30.2%, 200.4 °C and 25.6%, and 207.2 °C and 27.0%, respectively. The glass transition temperature (T_g) of­6‐O‐tritylcellulose by dynamic mechanical analysis (DMA) occurred at 126.7 °C and the modulus (E′, Pa) dropped 8.9 fold in the transition from ?150 °C to + 180 °C (6.6 × 10⁹ to 7.4 × 10⁸ Pa). Modulus at 20 °C was 3.26 × 10⁹ Pa. Complete proton and carbon‐13 chemical shift assignments of the repeating unit of the title polymer were made by a combination of the HMQC and COSY NMR methods. Ultimate non‐destructive proof of carbon–carbon bond formation at C6 of the anhydroglucose moiety was established by generating correlations between resonances of CH₂6 (anhydroglucose) and C1′, H2′, and H6′ of the attached aryl ring using the heteronuclear multiple‐bond correlation (HMBC) method. In this study, we achieved three major objectives: (a) new methodologies for the chemical modification of cellulose were developed; (b) new cellulose derivatives were designed, prepared and characterized; (c) unequivocal structural proof for carbon–carbon bond formation with cellulose was derived non‐destructively by use of one‐ and two‐dimensional NMR methods. Copyright © 2002 John Wiley & Sons, Ltd.     

Hydrolytic degradation of poly(ε‐caprolactone) with different end groups and poly(ε‐caprolactone‐co‐γ‐butyrolactone): characterization and kinetics of hydrocortisone delivery

Asymmetric telechelic α‐hydroxyl‐ω‐(carboxylic acid)‐poly(ε‐caprolactone) (HA‐PCL), α‐hydroxyl‐ω‐(benzylic ester)‐poly(ε‐caprolactone) (HBz‐PCL), and an asymmetric telechelic copolymer α‐hydroxyl‐ω‐(carboxylic acid)‐poly(ε‐caprolactone‐co‐γ‐butyrolactone) (HA‐PCB) were synthesized by ring‐opening polymerization of ε‐caprolactone (CL). CL and CL/γ‐butyrolactone mixture were used to obtain homopolymers and copolymer respectively at 150°C and 2 hr using ammonium decamolybdate (NH₄) [Mo₁₀O₃₄] (Dec) as a catalyst. Water (HA‐PCL and HA‐PCB) or benzyl alcohol (HBz‐PCL) were used as initiators. The three polylactones reached initial molecular weights between 2000 and 3000 Da measured by proton nuclear magnetic resonance (¹H‐NMR). Compression‐molded polylactone caplets were allowed to degrade in 0.5 M aqueous p‐toluenesulfonic acid at 37°C and monitored up to 60 days for weight loss behavior. Data showed that the copolymer degraded faster than the PCL homopolymers, and that there was no difference in the weight loss behavior between HA‐PCL and HBz‐PCL. Caplets of the three polylactones containing 1% (w/w) hydrocortisone were placed in two different buffer systems, pH 5.0 with citrate buffer and pH 7.4 with phosphate buffer at 37°C, and monitored up to 50 days for their release behavior. The release profiles of hydrocortisone presented two stages. The introduction of a second monomer in the polymer chain significantly increased the release rate, the degradation rate for HA‐PCB being faster than those for HBz‐PCL and HA‐PCL. At the pH studied, only slight differences on the liberation profiles were observed. SEM micrographs indicate that hydrolytic degradation occurred mainly by a surface erosion mechanism. Copyright © 2009 John Wiley & Sons, Ltd.     

Rigid‐rod polyamides and polyimides prepared from 4,3″‐diamino‐2′,6′‐di(2‐naphthyl)‐p‐terphenyl and 2′,6′,3‴,5‴‐tetra(2‐naphthyl)‐4,4″‐diamino‐p‐quinquephenyl

A series of rigid‐rod polyamides and polyimides containing p‐terphenyl or p‐quinquephenyl moieties in backbone as well as naphthyl pendent groups were synthesized from two new aromatic diamines. The polymers were characterized by inherent viscosity, elemental analysis, FT‐IR, ¹H‐NMR, ¹³C‐NMR, X‐ray, differential scanning calorimetry (DSC), thermomechanical analysis (TMA), thermal gravimetric analysis (TGA), isothermal gravimetric analysis, and moisture absorption. All polymers were amorphous and displayed T_g values at 304–337°C. Polyamides dissolved upon heating in polar aprotic solvents containing LiCl as well as CCl₃COOH, whereas polyimides were partially soluble in these solvents. No weight loss was observed up to 377–422°C in N₂ and 355–397°C in air. The anaerobic char yields were 57–69% at 800°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 15–24, 1999     

Temperature‐induced aggregation of the copolymers of N‐isopropylacrylamide and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate in aqueous solutions

A series of random copolymers of N‐isopropylacrylamide (NIPAM) and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate (AMPS) was synthesized by free‐radical copolymerization. The content of AMPS in the copolymers ranged from 1.1 to 9.6 mol %. The lower critical‐solution temperature (LCST) of copolymers in water increased strongly with an increasing content of AMPS. The influence of polymer concentration on the LCST of the copolymers was studied. For the copolymers with a higher AMPS content, the LCST decreased faster with an increasing concentration than for copolymers with a low content of AMPS. For a copolymer containing 1.1 mol % of AMPS the LCST dropped by about 3 °C when the concentration increased from 1 to 10 g/L, whereas for a copolymer containing 9.6 mol % of AMPS the LCST dropped by about 10 °C in the concentration range from 2 to 10 g/L. It was observed that the ionic strength of the aqueous polymer solution very strongly influences the LCST. This effect was most visible for the copolymer with the highest content of AMPS (9.6 mol %) for which an increase in the ionic strength from 0.2 to 2.0 resulted in a decrease in the LCST by about 27 °C (from 55 to 28 °C), whereas for the copolymer containing 1.1 mol % of AMPS the LCST decreased only by about 6 °C (from 37 to 31 °C) when the ionic strength increased from 0.005 to 0.3. The reactivity ratios for the AMPS and NIPAM monomer pairs were determined using different methods. The values of r_AMPS and r_NIPAM obtained were 11.0–11.6 and 2.1–2.4, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2784–2792, 2001     

Synthesis of Poly(2‐oxazoline)‐Based Hydrogels with Tailor‐Made Swelling Degrees Capable of Stimuli‐Triggered Compound Release

A 32‐membered library of poly(2‐oxazoline)‐based hydrogels of the composition p EtOx _m‐p PhOx _n‐p PBO _q (m/n = 150/0, 100/50, 50/100, and 0/150; q = 1.5–30) was prepared from 2‐ethyl‐ ( EtOx ), 2‐phenyl‐2‐oxazoline ( PhOx ), and phenylene‐1,3‐bis‐(2‐oxazoline) ( PBO ). The polymerizations were performed from ground monomer mixtures at 140 °C in a single‐mode microwave reactor in reaction times as short as 1 h. Purified hydrogels, containing no residual monomers, were obtained in yields of 95% or higher. Acid‐mediated hydrolysis rates as well as swelling degrees of the hydrogels were adjustable over a broad range; swelling degrees in water/ethanol/dichloromethane ranged from 0 to 13.8/11.7/20.0. The hydrogels could incorporate organic molecules according to in situ or post‐synthetic routines. Post‐synthetic routines enabled for the preparation of hydrogels from which the incorporated compounds were only released through diffusion processes if the solvent was changed or through hydrogel degradation if the pH was lowered.     

Chiral,pH responsive hydrogels constructed by N‐Acryloyl‐alanine and PEGDA/α‐CD inclusion complex: preparation and chiral release ability

Chiral, pH‐responsive hydrogels are constructed by poly(ethylene glycol) diacrylate/α‐cyclodextrin (PEGDA/α‐CD) inclusion complex and L‐N‐acryloyl‐alanine or D‐N‐acryloyl‐alanine (L‐NAA or D‐NAA) by an effective free radical polymerization approach. PEGDA containing two C=C end groups was used simultaneously to introduce α‐CD units in the resulting hydrogels and to serve as a cross‐linking agent, by which forming the designed hydrogels in quantitative yield. Hydrophilic α‐CD moieties acted as pore‐forming agent, while the L(D)‐NAA‐based polymer chains bearing –COOH groups enabled the hydrogels to display remarkable swelling–deswelling behavior in response to pH variation. The chiral NAA monomer‐derived polymer chains rendered the hydrogels with intriguing optical activity, according to circular dichroism spectra. Scanning electron microscopy revealed the uniformly porous microstructures of hydrogels. More remarkably, the L‐NAA‐based hydrogels preferentially adsorbed trans‐4‐hydroxy‐d ‐proline and preferentially released trans‐4‐hydroxy‐l ‐proline, while D‐NAA‐based hydrogels provided opposite results. The hydrogels also demonstrated remarkable enantioselective release ability towards chiral drug ibuprofen. Copyright © 2015 John Wiley & Sons, Ltd.     

固相β-环糊精包结物诱导7-羟基-2-甲氧基-2-甲基色满的不对称合成

研究了室温下间苯二酚和甲基乙烯基酮分别与β-环糊精（ β-CD）形成包结物后的几种不同固相反应,结果表明包结物A（间苯二酚/β-CD）与包结物B（甲基乙烯基酮/β-CD）反应能够很好地得到目的产物,产率及ee值分别为82.8%和78.4%;间苯二酚与包结物B反应仅得到低光学活性产物（ee值为19.5%）;包结物A与甲基乙烯基酮反应却没有得到手性目的产物。以熔点、X-粉末衍射、固相核磁碳谱及ROESY多种方法对所形成的包结物进行了表征,包结物中主客体的比例（1：1）通过¹H NMR (400 MHz)得以确定,文章对固相环加成反应的机制也进行了初步探讨。     

Layer‐by‐layer Assembled Multilayers of Graphene/Mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin for Detection of Dopamine

Graphene/mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin multilayer films composed of graphene sheet (GS) and mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin (NH₂‐β‐CD) were fabricated easily by two steps. First, negatively charged graphene oxide (GO) and positively charged mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin (NH₂‐β‐CD) were layer‐by‐layer (LBL) self‐assembled on glassy carbon electrode (GCE) modified with a layer of poly(diallyldimethylammonium chloride) (PDDA). Then graphene/mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin (GS/NH₂‐β‐CD) multilayer films were built up by electrochemical reduction of graphene oxide/mono‐(6‐amino‐6‐deoxy)‐β‐cyclodextrin (GO/NH₂‐β‐CD). Combining the high surface area of GS and the active recognition sites on β‐cyclodextrin (β‐CD), the GS/NH₂‐β‐CD multilayer films show excellent electrochemical sensing performance for the detection of DA with an extraordinary broad linear range from 2.53 to 980.05 µmol·L^?1. This study offers a simple route to the controllable formation of graphene‐based electrochemical sensor for the detection of DA.     

Thermo‐ and pH‐induced phase transitions and network parameters of poly(N‐isopropylacrylamide‐ co‐2‐acrylamido‐2‐methyl‐propanosulfonic acid) hydrogels

Dual temperature‐ and pH‐sensitive hydrogels composed of N‐isopropylacrylamide (NIPAM) and 2‐acrylamido‐2‐methyl‐propanosulfonic acid (AMPS) were prepared by free‐radical crosslinking copolymerization in aqueous solution at 22 °C. The mole percent of AMPS in the comonomer feed was varied between 0.0 and 7.5, while the crosslinker ratio was fixed at 5.0/100. The effect of AMPS content on thermo‐ and pH‐ induced phase transitions as well as equilibrium swelling/deswelling, interior morphology and network structure was investigated. The volume phase transition temperature (VPT‐T) was determined by both swelling/deswelling measurements and differential scanning calorimetry (DSC) technique. In addition, the volume phase transition pH (VPT‐pH) was detected from the derivative of the curves of the swelling ratio (dQ_v/dpH) versus pH. The polymer‐solvent interaction parameter (χ) and the average molecular mass between crosslinks ( ) of hydrogels were calculated from swelling ratios in buffer solutions at various pHs. The enthalpy (ΔH) and entropy (ΔS) changes appearing in the χ parameter of hydrogels were also determined by using the modified Flory–Rehner equation. The negative values for ΔH and ΔS indicated that the hydrogels had a negative temperature‐sensitive property in water, that is, swelling at a lower temperature and shrinking at a higher temperature. It was observed that the experimental swelling data of hydrogels at different temperature agreed with the modified Flory‐Rehner approach based on the affine network model. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1713–1724, 2008     

A novel pH‐ and thermo‐sensitive PVP/CMC semi‐IPN hydrogel: Swelling,phase behavior,and drug release study

Poly(N‐vinyl‐pyrrolidone) (PVP) hydrogel has been considered as a very interesting and promising thermosensitive material. The most vital shortcoming of PVP hydrogel as thermosensitive material is that it does not exhibit thermosensitivity under usual conditions. In this work, semi‐interpenetrating polymer network (semi‐IPN) hydrogels based on PVP and carboxymethylcellulose (CMC) were prepared. The volume phase transition temperature (VPTT) of the hydrogels was determined by swelling behavior and differential scanning calorimetry (DSC). The results showed that the VPTT was significantly dependent on CMC content and the pH of the swelling medium. The amount of CMC in the semi‐IPN hydrogels was 0.050, 0.075, and 0.100 g, the VPTT in buffer solution of pH 1.2 was 29.9 °C, 27.5 °C and 24.5 °C, respectively. In addition, the VPTT occurred in buffer solution of pH 1.2, but did not appear in alkaline medium. Bovine serum albumin (BSA) as a model drug was loaded and the in vitro release studies were carried out in different buffer solutions and at different temperatures. The results of this study suggest that PVP/CMC semi‐IPN hydrogels could serve as potential candidates for protein drug delivery in the intestine. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1749–1756, 2010     

Capillary electrophoretic separation and computational modeling of inclusion complexes of β‐cyclodextrin and 18‐crown‐6 ether with primaquine and quinocide

The antimalarial drug primaquine (PQ) and its contaminant, the positional isomer quinocide (QC) have been successfully separated using capillary electrophoresis with either β‐cyclodextrin (β‐CD) or 18‐crown‐6 ether (18C6) as chiral mobile phase additive. The interactions of the drugs with cyclodextrins and 18C6 were studied by the semiempirical method (Parametric Model 3) PM3. Theoretical calculations for the inclusion complexes of PQ and QC with α‐CD, β‐CD and 18C6 were performed. Data from the theoretical calculations are correlated and discussed with respect to the electrophoretic migration behavior. More stable complexes are predicted for the PQ–β‐CD and PQ–18C6 complexes. The coelution of PQ and QC when α‐CD was used as buffer additive can be explained by their comparable stabilities of the inclusion complex formed, while significant differences in the complexation stabilities of the drugs with β‐CD is responsible for their separation. The stronger hydrogen bonding in PQ–18C6 system is responsible for the separation between PQ and QC when 18C6 was used as chiral mobile phase additive. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and crystal structures of C24‐epimeric 20(R)‐ocotillol‐type saponins

Ocotillol‐type saponins have a wide spectrum of biological activities. Previous studies indicated that the configuration at the C24 position may be responsible for their stereoselectivity in pharmacological action and pharmacokinetics. Natural ocotillol‐type saponins share a 20(S)‐form but it has been found that the 20(R)‐stereoisomers have different pharmacological effects. The semisynthesis of 20(R)‐ocotillol‐type saponins has not been reported and it is therefore worthwhile clarifying their crystal structures. Two C24 epimeric 20(R)‐ocotillol‐type saponins, namely (20R,24S)‐20,24‐epoxydammarane‐3β,12β,25‐triol, C₃₀H₅₂O₄, (III), and (20R,24R)‐20,24‐epoxydammarane‐3β,12β,25‐triol monohydrate, C₃₀H₅₂O₄·H₂O, (IV), were synthesized, and their structures were elucidated by spectral studies and finally confirmed by single‐crystal X‐ray diffraction. The (Me)C—O—C—C(OH) torsion angle of (III) is 146.41 (14)°, whereas the corresponding torsion angle of (IV) is −146.4 (7)°, indicating a different conformation at the C24 position. The crystal stacking in (III) generates an R₄⁴(8) motif, through which the molecules are linked into a one‐dimensional double chain. The chains are linked via nonclassical C—H…O hydrogen bonds into a two‐dimensional network, and further stacked into a three‐dimensional structure. In contrast to (III), epimer (IV) crystallizes as a hydrate, in which the water molecules act as hydrogen‐bond donors linking one‐dimensional chains into a two‐dimensional network through intermolecular O—H…O hydrogen bonds. The hydrogen‐bonded chains extend helically along the crystallographic a axis and generate a C₄⁴(8) motif.     

Synthesis and properties of phosphorus containing polyester‐amides derived from 1,4‐bis(3‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl) phenylene

A series of polyester‐amides that contain phosphorus were synthesized by low temperature solution condensation of 1,4‐bis(3‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl) phenylene (III) with various aromatic acid chlorides in N‐methyl pyrrolidone (NMP). All polyester‐amides are amorphous and readily soluble in many organic solvents such as dimethylacetamide (DMAc), NMP, dimethylsulfoxide, and dimethylformamide at room temperature or on heating. Light yellow and flexible films of these polyester‐amides could be cast from the DMAc solutions. The polymers with an inherent viscosity of 0.26–0.72 dL/g were obtained in quantitative yields. These polyester‐amides have good mechanical properties (G′ of ∼ 10⁹ Pa up to 200°C) and good thermal and flame retardant properties. The glass transition temperatures of these polyester‐amides ranged from 250 to 273°C. The degradation temperatures (T_d 5%) in nitrogen ranged from 466 to 478°C and the char yields at 800°C were 59.6–65.2%. The limiting oxygen indexes of these polyester‐amides ranged from 35 to 43. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 891–899, 1999