含胺引发体系烯类聚合的研究

研究了BPO-胺引发体系中,不同胺对MMA聚合速度与所得聚合物色泽稳定性的影响,以及单独使用胺时对MEMA聚合的影响。实验结果表明:在前者情况下,胺对聚合反应的活性顺序为DMT≈DHET>DMA;而对聚合物的色泽稳定性也有类似的结果。从聚合速度与对色泽的要求来说,BPO-DMT与BPO-DHET是较好的引发体系。在后者的情况下,胺的活性顺序为DMT DHET>DMA>MBDMA,从聚合动力学研究可得R_p=K[DMT]~(1/2)[MEMA]_(3/2),聚合表现活化能E_a=34.3千焦耳/克分子(8.2千卡/克分子)。     

丙烯酸酯在胺存在下的氧化和聚合研究

胺促进丙烯酸酯氧化和聚合与胺及丙烯酸酯结构有关。芳香胺氮原子或苯环上有正性取代基时,促进作用大。带醚键的丙烯酸酯氧化和聚合快。 胺引发丙烯酸酯聚合认为先是胺促进丙烯酸酯氧化,生成单体过氧化物,与胺再形成复合物,分解产生自由基,促进更多丙烯酸酯氧化,继而引起聚合。     

有机过氧化物与N,N-二(2-羟烷基)对甲苯胺体系引发烯类聚合及其机理的研究

研究了有机过氧化物BPO,LPO分别与N,N-二(2-羟烷基)对甲苯胺DHET,DHPT组成的体系引发MMA的聚合。测定其聚合速度R_p,聚合表观活化能,聚合速度方程,聚合放热过程的温度与时间的关系。用自旋捕捉和ESR波谱技术,测定了上述体系反应产生的自由基中间体,同时通过聚合物端基分析证实DHET,DHPT组份产生的自由基能引发单体聚合。依据实验结果提出了这类体系的引发机理。     

过氧化二碳酸酯和N N-二羟烷基对甲苯胺体系引发甲基丙烯酸甲酯聚合

本文以过氧化二碳酸酯BPPD和芳叔胺DHET、DHPT、DMT、DMA组成的引发体系进行MMA聚合的研究。测定了聚合速率R_p,发现添加DHET、DHPT能促进MMA的聚合,缩短诱导期,提高R_p,其效果要比DMT、DMA为好。测定了E₃和聚合速率方程。由ESR谱和端基分析证实DHET、DHPT芳胺组分产生的自由基能引发单体聚合。     

芳香叔胺引发丙烯腈光聚合研究

我们发现芳香叔胺是丙烯腈聚合极有效的光引发剂。芳香叔胺苯环上氢被正性基取代时,引发能力增加,被负性基取代时,引发能力下降。下列胺的活性次序是:N,N-二甲基对甲苯胺(DMT)>N,N-二羟乙基对甲苯胺(DHET)>N,N-二甲基苯胺(DMA)>N,N-二甲胺基苯甲醛(DMB)>N,N-二甲基对硝基苯胺(DNA)。芳香叔胺引发丙烯腈光聚合属自由基机构,聚合速度与叔胺浓度的0.66次方成正比。在叔胺浓度为10~(-2)—10~(-4)M范围内,聚合物平均聚合度的倒数与叔胺浓度的0.5次方成正比。初步认为在紫外光激发下,芳香叔胺与丙烯腈分子生成激发态电子转移络合物,再分解产生自由基,引发丙烯腈聚合。     

STUDIES ON RADICAL POLYMERIZATION OF METHYL METHACRYLATE INITIATED WITH ORGANIC PEROXIDE-AMINE SYSTEMS

Radical polymerization of methyl mcthacrylate (MMA) initiated with various diacyl peroxideamine systems was studied. Benzoyl peroxide (BPO) and lauroyl peroxide (LPO) were used as diacyl peroxide component, N,N-dimethyl aniline (DMA) and its para substituted derivatives, i.e., N,N-dimethyl-p-toluidine (DMT), p-hydroxymethyl-N,N-dimethyl aniline (HDMA), p-nitro-N,N-dimethyl aniline (NDMA) and p-dimethylamino benzaldehyde (DMAB) were used as amine components. It was found that the peroxide-DMT systems give higher rates of bulk polymerization R_p of MMA than the organic hydroperoxide-DMT systems with the following descending order BPO-DMT>LPO-DMT>CHP (cumene hydroperoxide)-DMT>TBH (tert-butyl hydroperoxide)-DMT. The aromatic tertiary amines possess obvious structural effect on the R_p values in the diacyl peroxideamine system. The overall activation energy of MMA polymerization was determined and thekinetics of polymerization of MMA initiated with BPO-DMT system was investigated.     

STUDY OF THE EFFECT OF TWO BPO/AMINE INITIATION SYSTEMS ON THE FREE-RADICAL POLYMERIZATION OF MMA USED IN DENTAL RESINS AND BONE CEMENTS

ABSTRACT

The kinetics of the free radical bulk polymerization of methyl methacrylate (MMA) was studied by DSC, using the benzoyl peroxide (BPO)/amine initiation system. N,N dimethyl-4-aminophenethyl alcohol (DMPOH), which is a newly synthesized and used amine in the preparation of acrylic dental resins and bone cements was examined, and the results compared to the most commonly used in these applications amine, the N,N dimethyl-p-toluidine (DMT). For both amines, the effect of the molar ratio of BPO/amine and of the reaction temperature, on the polymerization kinetics was investigated. The prepared polymers were characterized by determination of the average molecular weights (M¯ _n and M¯ _w ) and molecular weights distribution (M¯ _w /M¯ _n ) using Gel Permeation Chromatography. DMPOH was found to lead in slightly higher polymerization rates, lower gel times and lower molecular weights than DMT. The values of these parameters for both amines were influenced by the molar ratio of BPO to amine, when the product of the concentrations of these was kept constant. The highest polymerization rate occurred in the lowest gel time, resulting in polymers with the lowest molecular weight, and was observed when a molar ratio of about 1.5 BPO/amine was used. However, the final monomer conversion was found to be independent of the molar ratio and amine used. The activation energy of polymerization was found to be 51.8 kJ/mol K for BPO/DMPOH and 47.1 kJ/mol K for BPO/DMT.     

SYNTHESIS AND POLYMERIZATION OF ALIPHATIC TERTIARY AMINO-GROUP N-SUBSTITUTED ACRYLAMIDES

Aliphatic tertiary amino-group N-substituted acrylamides, N-acryl-N′-methylpiperazine (AMP)and N-methacryl-N′-methylpiperazine (MAMP) were synthesized directly from N-methylpiperazinewith corresponding acryloyl chlorides and characterized by elementary analysis of their picrates,~1H-NMR, IR and MS. AMP did not polymerize with benzoyl peroxide (BPO), but could poly-merize with lauroyl peroxide (LPO). The rate equation of the polymerization was given as R_P=K_P [AMP]~(1.5)[LPO]~(0.5) and the overall activation energy of this polymerization system was 10.8Kcal/mol. The redox nature of LPO with the monomer itself was suggested. Even though AMP and MAMP hardly proceed the polymerization initiated with BPO, butunder lower concentration would form redox system with BPO to initiate the polymerization of MMAreadily. The rate equation of the polymerization of MMA initiated with MAMP-BPO systemwas given as R_P=K_P [MMA] [MAMP}~(0.5) [BPO]~(0.5) and the overall activation energy was 10.2Kcal/mol. The analysis of the obtained polymers confirmed that MAMP not only initiated the poly-merization of MMA by combining with BPO, but also took part in the polymer chains impartingthem with better biocompatibility.     

有机过氧化物-芳叔胺体系引发甲基丙烯酸甲酯聚合的研究

以过氧化二酰(BPO、LPO)或有机过氧化氢物(TBH、CHP)和芳叔胺如DMA或对位具有不同取代基的衍生物组成的引发体系进行MMA聚合,研究过氧化物与胺的结构对聚合的影响。结果表明,过氧化二酰的活性要比有机过氧化氢物大,其顺序为BPO>LPO>CHP>TBH。对于BPO-芳叔胺或LPO-芳叔胺体系,芳叔胺中给电子取代基能提高聚合速度,而吸电子取代基能降低聚合速度。测定了MMA聚合的总活化能E_α,BPO-芳叔胺体系时E_α=36-54kJ/mole,LPO-芳叔胺体系时E_α=56-71kJ/mole;还研究聚合动力学。     

Effect of amines on the ceric ion-initiated polymerization of vinyl monomers. II. Polymerization of acrylonitrile by ceric ion in presence of various substituted amines

The effect of various substituted amines on the polymerization of acrylonitrile initiated by ceric ammonium sulfate has been studied in aqueous solution at 30°C. It was found that the secondary and tertiary amines considerably increased the rate of polymerization, whereas the primary amines seemed to have no effect at all. From the kinetic studies it was found that the overall polymerization rate R_p is independent of ceric ion concentration and can be expressed by the equation: R_p = k₁ [amine] [monomer] + k₂[monomer]², where k₁ and k₂ are constants (involving different rate constants). The accelerating effect of the amines was attributed to a redox reaction between the ceric ion and the amine involving a single electron transfer, the relative activity of the different amines being thus dependent on the relative electron-donating tendency of the substituents present in the amine. The mechanism of the polymerization is discussed on the basis of these results, and various kinetic constants are evaluated.     

Precipitation polymerization of acrylamide using vazo-33 as an initiator and acetonitrile/water mixtures as the solvent

Precipitation polymerization of acrylamide initiated by a thermal initiator, Vazo-33 (DuPont Vazo Initiator), was achieved at a solvent composition of acetonitrile/water = 4/6 (vol/vol). The polymerization kinetics were investigated in the acrylamide [M] concentration range 0.86–2.27M, Vazo-33 [I] concentration range 1.4–11.0 × 10^?4M, and temperature range 30–40°C. Polymerization was carried out in reaction ampules and the rate was determined gravimetrically. Number-average molecular weight was obtained from intrinsic viscosity. The precipitation polymerization rate varied as [M]^2.16 and [I]^0.44. Number-average molecular weight was proportional to [M]^1.22 and inversely proportional to [I]^0.31. The overall reaction activation energy was calculated as 17.3 kcal/mol in the temperature range studied. The optimal reaction conditions studied were: acetonitrile/water = 4/6, temperature = 40°C, [M] = 1.95M and [I] = 2.8 × 10^?4M. One hundred percent conversion was achieved in 90 min and a polymer with a number-average molecular weight of 1,200,000 was obtained.     

Anomalies in the polymerization kinetics of 4-dimethylaminostyrene initiated with trichloracetic acid in nitrobenzene

The relative permittivities (?_r²⁰) of 4-dimethylaminostyrene (I) and of 0.5–3.0 M solutions of N,N-dimethyl-4-toluidine (DMT) were measured in nitrobenzene (NB) and in a mixture of NB with diisopropyl ether (NB + E), the DMT solutions modelled those of I. An increase in [DMT] from 0.5 to 3.0 M caused a decrease in ?_r²⁰ from 32.3 to 18.3 in NB, while only from 20.8 to 18.3 in (NB + E) at fixed [NB]. The great difference between the ?_r²⁰ of 0.5 and 3.0 M DMT solutions in NB explains the previously observed drop in the percentage rate of polymerization (R_P) of I, in NB initiated with CCl₃COOH, with increasing [I]_o. In (NB + E) mixture with fixed [NB], the percentage R_P and the limiting viscosity number [ν] of polyl increase with increasing [I]_o. The observed dependences of both R_P (in Msec^?1) and [ν] on [I]₀ confirm the validity of the suggested polymerization scheme for I initiated with CCl₃COOH, and make possible determination of the characteristics of the elementary polymerization reactions.     

Kinetics of polymerization of styrene-in-water microemulsions

The kinetics of polymerization of styrene-in-water microemulsions was investigated using dilatometry. From plots of percentage conversion versus time, the rate of polymerization, R _p, was determined. From log-log plots of R _p versus styrene and initiator [2,2′-azobis(isobutyronitrile), AIBN] concentrations the following relationship was established: R _p∝ [styrene]^1.2 [AIBN]^0.46. These exponents are similar to those predicted by the theory of emulsion polymerization. The results also showed a rapid conversion in the initial period (interval 1) followed by a slower rate at longer times (interval 2). It was suggested that in interval 1, the main process in nucleation of the microemulsion droplets, whereas in interval 2 propagation is the more dominant factor. The rapid polymerization of microemulsions is consistent with their structure, whereby very small droplets with flexible interfaces are produced. Received: 2 March 1999 Accepted in revised form: 10 May 1999     

有机过氧化物与N,N-二羟烷基对甲苯胺引发体系的研究

<正> 有机过氧化二苯甲酰(BPO)与N,N-二甲基苯胺(DMA)组成的引发体系称为有机氧化还原引发体系.为了提高聚合速度和聚合物的颜色稳定性,发展了BPO-DMT(N,N-二甲基对甲苯胺)引发体系,并已应用于医用高分子的齿科材料和骨水泥中.文献[3]曾简单提到N,N-二2-羟乙基苯胺(DHEA)作为促进剂,其活性与DMA相似;另外BPO可分别与N,N-二(2-羟乙基)对甲苯胺(DHET)和N,N-二(2-羟丙基)对甲苯胺(DHPT)组成引发体系,作为烯类自由基聚合的室温固化剂,但对聚合速度和聚合动力学报道甚少.由于DHPT熔点较高又无刺激味道,因而很适用于自凝齿科林     

奋乃静和有机过氧化物引发体系及含奋乃静的缓释药膜

研究了含叔胺基结构的药物奋乃静（Ｐｅｒｐｈｅｍｎａｚｉｎｕｍ，简称ＰＥＲＰ）和有机过氧化物所构成的引发体系，并以此体系引发丙烯酸酯类单体聚合所得的含奋乃静缓释药膜的缓释行为．结果表明，奋乃静（ＰＥＲＰ）和过氧化苯甲酰（ＢＰＯ）引发体系引发甲基丙烯酸甲酯（ＭＭＡ）聚合的动力学方程为：Ｒｐ＝Ｋｐ［ＢＰＯ］０５［ＰＥＲＰ］０５［ＭＭＡ］１０，聚合表观活化能Ｅａ＝４１８ＫＪ／ｍｏｌ，从而确定此引发体系的引发机理为氧化还原引发机理．ＰＥＲＰ ＢＰＯ体系能在４０℃温度下，引发丙烯酸酯类单体共聚，而能形成含有奋乃静的缓释药膜     

有机过氧化氢物与芳叔胺体系引发甲基丙烯酸甲酯聚合的研究

以有机过氧化氢物叔丁基过氧化氢(TBH)或异丙苯过氧化氢(CHP)与芳叔胺N,N-二甲基苯胺(DMA)或其衍生物组成的体系引发甲基丙烯酸甲酯(MMA)聚合。研究有机过氧化氢物与芳叔胺结构对聚合的影响,测定了TBH-胺与CHP-胺体系引发MMA聚合的总活化能分别为50-57KJ/mol与39-62KJ/mol,并对CHP-DMT(N,N-二甲基对甲苯胺)引发MMA聚合动力学以及有关引发聚合机理进行了研究。     

甲基丙烯酸2-羟乙酯水溶液聚合与硫氰化钠的效应

<正> 甲基丙烯酸2-羟乙酯(HEMA)是一带有羟基的功能性单体,它可以在自由基聚合引发剂如过氧化苯甲酰、偶氮二异丁腈、过氧化二碳酸二异丙酯或氧化还原引发体系过硫酸盐-乙酸二甲胺基乙酯的作用下进行自由基聚合,我们已报道带有羟基的单体如HEMA、甲基丙烯酸羟丙酯(HPMA)及甲基丙烯酯3-甲氧基-2-羟丙酯(MHPMA)可用     

Kinetic studies on the imine base/isocyanate‐induced radical polymerization of vinyl monomers

Specific imine bases (IB) in conjunction with various isocyanates (IC) mediate the radical polymerization of radically polymerizable monomers such as methyl methacrylate (MMA). Advantageously, the 2‐(methylmercapto)‐2‐thiazoline MMT/IC combination as initiator works even at room temperature for polymerization of MMA. The coefficients a, b, and c of the basic rate law of monomer consumption d[M]/dt = k_p·[IC]^a·[IB]^b·[M]^c were determined. The order a has been determined to 0.5 showing the root law of radical polymerization with respect to the IC component as initiator. Moreover, b and c amount 1. The initiator combination MMT/ IC was applied to determine the influence of the molecular structure of the IC on the rate of monomer conversion. For aromatic isocyantes, the gross rate constant of monomer consumption correlates with the Hammet constant of aromatic substituents. The activation energies of the gross polymerization rate constant of several initiator mixtures were determined whereby the value of E_A,Br was found to be between typical values of radical polymerization initiated by photochemical reactions (～20 kJ/mol) and commonly used thermal decomposing initiators (～80 kJ/mol). Presumptions on the initiating and terminating step of the IB/IC mediated polymerization were done by means of electrospray ionization mass spectrometry, NMR spectroscopy, and the elemental composition of the head and end group of the resulting polymers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Anionic and ionic coordinative polymerization of ϵ‐caprolactone

The polymerization of ?‐caprolactone initiated by two catalyst systems was studied: (1) carbazole‐potassium in the presence of 18‐crown‐6 ether and (2) NdCl₃/TBP/TIBA (neodymiumtrichloride/tri‐n‐butyl‐phosphate/triisobutylaluminium) at the molar ratio 1/3/1. For both initiator systems conversion/time plots were determined and the polymers were characterized by IR, GPC and by ¹H‐ and ¹³C?NMR spectroscopy. Polyesters with the highest molecular weight (M _n?44 000 g/mol) were obtained for the polymerizations initiated by the carbazole‐potassium/18‐crown‐6 ether system. The features of the polymerization initiated by the carbazole‐potassium/18‐crown‐6 ether system are discussed on the basis of a simple scheme. The nature of this polymerization is non‐living. Copyright © 2000 John Wiley & Sons, Ltd.     

Polymerization of acrylonitrile: Kinetics of the reaction initiated by the Fe2+/BrO3− redox system

The aqueous polymerization of acrylonitrile initiated by the bromate—ferrous redox system in aqueous sulfuric acid was studied under nitrogen atmosphere. The rate of polymerization increased with increasing concentration of ferrous in the range of 0.25-1 × 10^?2M. The percentage of conversion increased with increasing concentration of the catalyst, but beyond 2.5 × 10^?3M there was a decreasing trend in the rate of polymerization. The rate varied linearly with [monomer]. The initial rate of polymerization as well as the maximum conversion increased within the range of 1–2.5 × 10^?3M KBrO₃, but beyond 2.5 × 10^?3M the rate of polymerization decreased. The initial rate and limiting conversion increased with increasing polymerization temperature in the range 30–40°C; beyond 40°C they decreased. The effect of certain neutral salts, water-miscible solvents, complexing agents, and copper sulfate concentration on the rate of polymerization was investigated.