Simultaneous determination of N-acetyl-p-aminophenol and p-aminophenol with poly(3,4-ethylenedioxythiophene) modified glassy carbon electrode

A sensitive and selective method was developed for the determination of N-acetyl-p-aminophenol (APAP) and p-aminophenol (PAP) using poly(3,4-ethylenedioxythiophene) (PEDOT)-modified glassy carbon electrode (GCE). Cyclic voltammetry and differential pulse voltammetry were used to investigate the electrochemical reaction of APAP and PAP at the modified electrode. Both APAP and PAP showed quasireversible redox reactions with formal potentials of 367 mV and 101 mV (vs. Ag/AgCl), respectively, in phosphate buffer solution of pH 7.0. The significant peak potential difference (266 mV) between APAP and PAP enabled the simultaneous determination both species based on differential pulse voltammetry. The voltammetric responses gave linear ranges of 1.0 × 10⁻⁶-1.0 × 10⁻⁴ mol L⁻¹ and 4.0 × 10⁻⁶-3.2 × 10⁻⁴ mol L⁻¹, with detection limits of 4.0 × 10⁻⁷ mol L⁻¹ and 1.2 × 10⁻⁶ mol L⁻¹ for APAP and PAP, respectively. The method was successfully applied for the determination of APAP and PAP in pharmaceutical formulations and biological samples.     

Preparation and characterization of p-tert-butylcalix[8]arene bonded capillaries for open-tubular capillary electrochromatography

p-tert-Butylcalix[8]arene bonded capillaries for open-tubular capillary electrochromatography were prepared with γ-glycidoxypropyltrimethoxysilane as a bridge. The bonded capillary displayed low and steady electroosmotic flow (EOF) values over the pH range from 4 to 9. Detection limits for direct spectrophotometric detection at 277 nm for benzenediols (at a signal to noise ratio of 2) were 0.96 mg l⁻¹ for the unbonded capillary and 1.48 mg l⁻¹ for the bonded capillary, showing that the bonded layer did not show significant absorbance and hence decreased sensitivity. The bonded capillaries showed good separation selectivity for o-, m- and p-benzenediols, α- and β-naphthols, and α- and β-naphthylamines. This selectivity was attributed to significant interactions between the analytes and the bonded p-tert-butylcalix[8]arene, which contributed to the electrochromatographic separation mechanism. The bonded capillaries gave high stability and reproducibility.     

A multicommuted flow system for sequential spectrophotometric determination of hydrosoluble vitamins in pharmaceutical preparations

A multicommuted flow system is proposed for spectrophotometric determination of hydrosoluble vitamins (ascorbic acid, thiamine, riboflavine and pyridoxine) in pharmaceutical preparations. The flow manifold was designed with computer-controlled three-way solenoid valves for independent handling of sample and reagent solutions and a multi-channel spectrophotometer was employed for signal measurements. Periodic re-calibration as well as the standard addition method was implemented by using a single reference solution. Linear responses (r=0.999) were obtained for 0.500-10.0 mg l⁻¹ ascorbic acid, 2.00-50.0 mg l⁻¹ thiamine, 5.00-50.0 mg l⁻¹ riboflavine and 0.500-8.00 mg l⁻¹ pyridoxine. Detection limits were estimated as 0.08 mg l⁻¹ (0.5 μmol l⁻¹) ascorbic acid, 0.8 mg l⁻¹ (2 μmol l⁻¹) thiamine, 0.2 mg l⁻¹ (0.5 μmol l⁻¹) riboflavine and 0.1 mg l⁻¹ (0.9 μmol l⁻¹) pyridoxine at 99.7% confidence level. A mean sampling rate of 60 determinations per hour was achieved and coefficients of variation of 1% (n=20) were estimated for all species. The mean reagent consumption was 25-fold lower in relation to flow-based procedures with continuous reagent addition. Average recoveries between 95.6 and 100% were obtained for commercial pharmaceutical preparations. Results agreed with those obtained by reference methods at 95% confidence level. The flow system is suitable for application in quality control processes and in dissolution studies of vitamin tablets.     

Interfacing in-line gas-diffusion separation with optrode sorptive preconcentration exploiting multisyringe flow injection analysis

An automatic multisyringe flow injection analysis (MSFIA) system coupling a flow-through optical fiber diffuse reflectance sensor with in-line gas-diffusion (GD) separation is proposed for the isolation, preconcentration and determination of traces of volatile and gas-evolving compounds in samples containing suspended solids, with no need for any preliminary batch sample treatment. The flowing methodology overcomes the lost of sensitivity of the in-line separation technique, when performed in a uni-directional continuous-flow mode, through the implementation of disk-based solid-phase extraction schemes. The high selectivity and sensitivity, the low reagent consumption and the miniaturization of the whole assembly are the outstanding features of the automated set-up. The proposed combination of techniques for separation, flow analysis, preconcentration and detection was applied satisfactorily to sulfide determination in environmental complex matrixes. The method based on multicommutation flow analysis involves the stripping of the analyte as hydrogen sulfide from the donor channel of the GD-module into an alkaline receiver segment, whereupon the enriched plug merges with well-defined zones of the chormogenic reagents (viz., N,N-dimethyl-p-phenylenediamine (DMPD) and Fe(III)). The in-line generated methylene blue dye is subsequently delivered downstream to the dedicated optrode cell furnished with a C₁₈ disk, while recording continuously the diffuse reflectance spectrum of the pre-concentrated compound. This procedure provides a linear working range of 20-500 μg l⁻¹ sulfide with a relative standard deviation of 2.2% (n = 10) at the 200 μg l⁻¹ level, and a detection limit of 1.3 μg l⁻¹.     

Determination of bismuth and zinc in pharmaceuticals by first derivative UV-Visible spectrophotometry

A first order derivative spectrophotometric method has been developed for the simultaneous determination of bismuth and zinc by dithizone without time-consuming extraction step. The reactions of bismuth and zinc with dithizone in a three component solution prepared in water, acetone and n-propanol mixture have been investigated. These cations react with dithizone in this mixture at pH 5.0, forming coloured complex that is stable for at least 2 h. The linear range in D evaluation was between 3.0 × 10⁻⁶ and 1.8 × 10⁻⁵ mol l⁻¹ for Zn and 2.4 × 10⁻⁶ and 1.2 × 10⁻⁵ mol l⁻¹ for Bi. The limits of detection for the analytical procedure were found 0.05 mg l⁻¹ for both cations. The relative standard deviations for the determination of 0.5 mg l⁻¹ bismuth and 0.5 mg l⁻¹ zinc were 1.2 and 1.1%, respectively, for five determinations. The procedure is simple, rapid and reliable. This method was applied to the determination of bismuth and zinc in the pharmaceutical materials successfully. Good agreement was achieved between the results obtained by the proposed and comparative methods.     

Sequential injection lab-on-valve simultaneous spectrophotometric determination of trace amounts of copper and iron

A sequential injection (SI) method in a lab-on-valve (LOV) format for simultaneous spectrophotometric determination of copper and iron has been devised. The detection chemistry is based on the complex formation of 2-(5-bromo-2-pyridylazo)-5-[N-n-propyl-N-(3-sulfopropyl)amino]aniline (5-Br-PSAA) with copper(II) and/or iron(II) at pH 4.6. Copper(II) reacts with 5-Br-PSAA to form the complex which has an absorption maximum at 580 nm but iron(III) does not react. In the presence of a reducing agent only iron(II)-5-Br-PSAA complex is formed and detected at 558 nm. Under the optimum experimental conditions, the determinable ranges are 0.1-2 mg l⁻¹ for copper and 0.1-5 mg l⁻¹ for iron, respectively, with a sampling rate of 18 h⁻¹. The limits of detection are 50 μg l⁻¹ for copper and 25 μg l⁻¹ for iron. The relative standard deviations (n = 15) are 2% for 0.5 mg l⁻¹ copper and 1.8% for 0.5 mg l⁻¹ iron when determined in standard solutions. The recoveries range between 96 and 105% when determining 0.25-2 mg l⁻¹ of copper and 0.2-5 mg l⁻¹ of iron in artificial mixtures at copper/iron ratios of 1:10 to 5:1. The proposed SI-LOV method is successfully applied to the simultaneous determination of copper and iron in multi-element standard solution and in industrial wastewater samples.     

Solvent extraction flow-injection manifold for the simultaneous spectrophotometric determination of free cyanide and thiocyanate ions based upon on-line masking of cyanides by formaldehyde

This study reports a sensitive solvent extraction flow-injection (FI) method for the simultaneous spectrophotometric determination of free cyanide and thiocyanate in human saliva and pralidoxime solutions. Cyanide and thiocyanate form colored (λ_max=540 nm) ternary complexes with copper and 2,2′-dipyridyl-2-quinolylhydrazone (DPQH) that are extractable into chloroform. The determination of thiocyanates in the presence of cyanides is accomplished after on-line masking of the latter with formaldehyde through a binary inlet static mixer (BISM). Total thiocyanates and cyanides are determined in a second run, without the use of the masking agent. The proposed method allows the determination of the analytes in the range of 0-4 mg l⁻¹ thiocyanates and 0-3 mg l⁻¹ cyanides, with the 3σ detection limits being 0.007 and 0.004 mg l⁻¹, respectively. The precision of the method (s_r<1.0% at 1 mg l⁻¹ CN⁻ or SCN⁻, n=12 in both cases) and the sampling rates were quite satisfactory (60 injections per hour). The method was applied to the analysis of human saliva and pralidoxime solutions and gave recoveries in the range of 98.0-102.2% for both analytes whereas the mean relative error was e_r=1.7%.     

Determination of myo-inositol hexakisphosphate (phytate) in urine by inductively coupled plasma atomic emission spectrometry

Myo-inositol hexakisphosphate (phytate) is a substance present in urine with an important role in preventing calcium renal calculi development. In spite of this, the use of urinary phytate levels on stone-formers’ evaluation and treatment is still notably restricted as a consequence of the enormous difficulty to analyze this substance in urine. In this paper, a simple procedure for routinary urinary phytate determination based on phosphorus determination through inductively coupled plasma atomic emission spectrometry is described.The method only requires a previous separation of phytate from other components by column anion exchange chromatography. The working linear range used was 0-2 mg l⁻¹ phosphorus (0-7 mg l⁻¹ phytate). The limit of detection was 64 μg l⁻¹ of phytate and the limit of quantification was 213 μg l⁻¹. The relative standard deviation (R.S.D.) for 1.35 mg l⁻¹ phytate was 2.4%. Different urine samples were analyzed using an alternative analytical methodology based on gas chromatography (GC)/mass detection used for inositol determination (phytate was previously hydrolyzed), resulting both methods comparable using as criterion to assess statistical significance P<0.05.     

Microcalorimetry as a possible tool for phenanthrene toxicity evaluation to eukaryotic cells

Microcalorimetry and measurement of culture turbidity using a Bioscreen C Analyzer System were applied to study the toxic effect of phenanthrene on Cunninghamella elegans IM 1785/21Gp spore germination. The results of C. elegans spore incubation in Bioscreen C microbiology reader showed the inhibition of spore germination by 70% (with 25 mg l⁻¹ of phenanthrene) and total inhibition of the fungus growth with a higher content of the xenobiotic (50-100 mg l⁻¹). The microcalorimetric technique showed to be useful for the estimation of metabolic activity of C. elegans spores in growth medium up to xenobiotic concentrations of 90 mg l⁻¹. These data corresponded with the microscopic observations. The obtained results showed that the microcalorimetry method could be a valuable supplement in the study on the mechanism of PAHs detoxification by fungi.     

Determination of furosemide in pharmaceutical formulations by diffuse reflectance spectroscopy

In this report an analytical method to determine furosemide by using diffuse reflectance spectroscopy is presented. This study shows that this technique can give quantitative results using spot test analysis, particularly in the case of pharmaceuticals containing furosemide. The color spot test could be obtained by reaction between furosemide with p-dimethylaminocinnamaldehyde, in acid medium. This reaction produced a stable complex on filter paper after heating to 80 °C for 5 min. All reflectance measurements were carried out at 585 nm and the linear range was from 7.56×10⁻³ to 6.05×10⁻² mol l⁻¹, with a correlation coefficient of 0.999. The limit of detection was estimated to be 2.49×10⁻³ mol l⁻¹ (R.S.D.=1.7%) and the effect of common excipients on the reflectance measurements was evaluated. The method was applied to determine furosemide in commercial brands of pharmaceuticals. The results obtained by the proposed method were favorably compared with those of the official method, showing for the first time ever that quantitative spot test analysis by diffuse reflectance could be successfully used to determine furosemide in tablets.     

Chemiluminometric determination of the pesticide 3-indolyl acetic acid by a flow injection analysis assembly

A new method is proposed for the chemiluminescent determination of the pesticide 3-indolyl acetic acid by means of an flow injection analysis system. The chemiluminescence emission is obtained by oxidation of the analyte with Ce (IV) in nitric acid and presence of β-cyclodextrine.The continuous-flow method allows the determination of 159 samples h⁻¹ of 3-indolyl acetic acid in an interval of concentrations over the range 0.5-15.0 mg l⁻¹. The limit of detection was 0.1 μg l⁻¹ and the R.S.D. (n, 17) at 2.0 mg l⁻¹ of the pesticide level was 2.7%. The method was applied to water samples.     

Determination of bromide ions in seawater using flow system with chemiluminescence detection

A simple flow-based procedure with chemiluminescence (CL) detection is proposed for bromide ion determination in seawater. The procedure was based on the oxidation of bromide to bromine by chloramine-T followed by the reaction of bromine with luminol resulting in CL emission. Since no significant reaction within chloramine-T and luminol was observed, the detection was carried out without bromine extraction from the oxidant medium. The proposed flow system had a sampling rate of 40 determinations per hour, reagents consumption of 100 μg luminol and 60 μg chloramine-T per determination, a limit of detection of 0.5 mg l⁻¹ bromide ions, a linear concentration range (r = 0.999 and n = 7) between 0 and 100 mg l⁻¹, and a coefficient of variance better than 2.5% (for 10 measurements of a 10 mg l⁻¹ Br⁻ solution) were achieved. The analytical system was applied for the determination of bromide in seawater and estuarine-water samples, obtaining an analyte recovery ranging from 94 to 102% and comparing the results with a reference spectrophotometric method no significant difference was observed in 95% confidence level.     

Sequential injection spectrophotometric determination of phenylephrine hydrochloride in pharmaceutical preparations

A fully automated sequential injection spectrophotometric method for the determination of phenylephrine hydrochloride in pharmaceutical preparations is reported. The method is based on the condensation reaction of the analyte with 4-aminoantipyrine in the presence of potassium ferricyanide. The absorbance of the condensation product was monitored at 503 nm. A linear relationship between the relative peak height and concentration was obtained in the range 0.5-17.5 mg l⁻¹. The detection limit (as 3σ value) was 0.09 mg l⁻¹ and repeatability was 0.8 and 0.6% at 2.5 and 5 mg l⁻¹, respectively. Results obtained by this method agreed very well with those obtained by the AOAC official method.     

p-Aminobenzoate ion determination in pharmaceutical formulations by using a potentiometric sensor immobilized in a graphite matrix

The characteristics, performance, and application of an electrode, namely, Pt|Hg|Hg₂(PABzt)₂| graphite, where PABzt stands for p-aminobenzoate ion, are described. This electrode responds to PABzt with sensivity of (58.1±1.0) mV per decade over the range 1.0×10⁻⁴ to 1.0×10⁻¹ mol l⁻¹ at pH 6.5-8.0 and a detection limit of 3.2×10⁻⁵ mol l⁻¹. The electrode shows easy construction, fast response time (within 10-30 s), low-cost, and excellent response stability (lifetime greater than 6 months, in continuous use). The proposed sensor displayed good selectivity for p-aminobenzoate in the presence of several substances, especially, concerning carboxylate and inorganic anions. It was used to determine p-aminobenzoate in pharmaceutical formulations by means of the standard additions method. The results obtained by using this electrode compared very favorably with those given by an HPLC procedure.     

Artificial neural networks study of the catalytic reduction of resazurin: stopped-flow injection kinetic-spectrophotometric determination of Cu(II) and Ni(II)

An artificial neural network (ANN) procedure was used in the development of a catalytic spectrophotometric method for the determination of Cu(II) and Ni(II) employing a stopped-flow injection system. The method is based on the catalytic action of these ions on the reduction of resazurin by sulfide. ANNs trained by back-propagation of errors allowed us to model the systems in a concentration range of 0.5-6 and 1-15 mg l⁻¹ for Cu(II) and Ni(II), respectively, with a low relative error of prediction (REP) for each cation: REP_Cu(II) = 0.85% and REP_Ni(II) = 0.79%. The standard deviations of the repeatability (s_r) and of the within-laboratory reproducibility (s_w) were measured using standard solutions of Cu(II) and Ni(II) equal to 2.75 and 3.5 mg l⁻¹, respectively: s_r[Cu(II)] = 0.039 mg l⁻¹, s_r[Ni(II)] = 0.044 mg l⁻¹, s_w[Ni(II)] = 0.045 mg l⁻¹ and s_w[Ni(II)] = 0.050 mg l⁻¹. The ANNs-kinetic method has been applied to the determination of Cu(II) and Ni(II) in electroplating solutions and provided satisfactory results as compared with flame atomic absorption spectrophotometry method. The effect of resazurin, NaOH and Na₂S concentrations and the reaction temperature on the analytical sensitivity is discussed.     

A multisyringe sequential injection method for monitoring water in the energy cogeneration system of a municipal waste incinerator

Leading-edge urban solid waste ashing plants use burning heat energy to obtain electrical power. Water fed to their boilers for conversion into steam should be highly pure in order to minimize corrosion, scaling and similar phenomena, which can lead to malfunctioning and a reduced useful life but can be avoided by proper management and control of the water supply. In this work, we developed a multiparameter monitor based on multisyringe sequential injection for the sequential determination of up to eight important parameters, namely: pH, specific and acid conductivity, hydrazine, ammonium, phosphate, silicate and total iron.Acid conductivity was determined by passing the sample through a cation-exchange resin in order to retain ammonium ion and release protons. This parameter was deemed the most accurate indicator of dissolved solids in boiler water. Chemical parameters were determined spectrophotometrically: hydrazine by reaction with p-dimethylaminobenzaldehyde, ammonium by the modified Berthelot reaction, iron with o-phenanthroline, and phosphate and silica by formation of a molybdoheteropoly blue dye in the presence of ascorbic acid as reductant. Use of the optimum chemical and physical operating conditions provided 3s_blank detection limits of 0.01 mg l⁻¹ N₂H₄, 0.13 mg l⁻¹ NH₄⁺, 0.04 mg l⁻¹ Fe, 0.03 mg l⁻¹ SiO₂ and 0.05 mg l⁻¹ PO₄³⁻, and relative standard deviations not greater than 2.5%. The methods integrated in the proposed monitor were successfully applied to real samples from the water-steam cycle at the Son Reus ashing plant in Palma de Mallorca (Spain).     

Design and evaluation of a thorium (IV) selective optode

A novel optical sensor has been proposed for sensitive determination of thorium (IV) ion in aqueous solutions. The thorium sensing membrane was prepared by incorporating 4-(p-nitrophenyl azo)-pyrocatechol (NAP) as ionophore in the plasticized PVC membrane containing tributyl phosphate (TBP) as plasticizer. The membrane responds to thorium ion by changing color reversibly from yellow to red-brown in glycine buffer solution at pH 3.5. The proposed sensor displays a linear range of 8.66 × 10⁻⁶-2.00 × 10⁻⁴ M with a limit of detection of 6 × 10⁻⁶ M. The response time of the optode was about 8.8-12.5 min, depending on the concentration of Th (IV) ions. The selectivity of optode to Th (IV) ions in glycine buffer is good. The sensor can readily be regenerated by exposure to a solution mixture of sodium fluoride and 5-sulfosalicylic acid (dihydrate) (0.01 M each). The optode is fully reversible. The proposed optode was applied to the determination of thorium (IV) in environmental water samples.     

Chemiluminometric photo-induced determination of Strychnine in a Multicommutation flow assembly

This paper deals on the determination of Strychnine, a potent and dangerous pesticide and the analytical procedure is based on the photo-induced chemiluminescence of the pesticide by means of the Multicommutation continuous-flow methodology. Small segments of the pesticide solution were sequentially alternated with segments of the solution for adjusting the suitable medium for the photodegradation. The required time of UV irradiation was obtained by stopped-flow during 150 s; then, the resulting solution formed alternated segments with the oxidizing solution containing 5 × 10⁻³ mol l⁻¹ Ce(IV) in 0.6 mol l⁻¹ nitric acid. The calibration range, from 2 μg l⁻¹ to 50 mg l⁻¹, resulted in a linear behaviour over the range 25 μg l⁻¹ to 20 mg l⁻¹ and fitting the equation: I = 4706x + 624 with a correlation coefficient of 0.9955. The limit of detection was 2 μg l⁻¹ and the sample throughput 15 h⁻¹. After testing the influence of a large series of potential interferents, the method was applied to different kinds of samples.     

Flow injection system with in-line Winkler's procedure using 16-way valve and spectrofluorimetric determination of dissolved oxygen in environmental waters

Flow injection spectrofluorimetry with in-line Winklers procedure was developed for the dissolved oxygen (DO) determination. 2-Thionaphthol reacted with iodine produced by Winkler’s method to form fluorescence inactive disulfide compound. To automate the process completely, a 5-channel flow system with a newly designed 16-way valve was assembled. The system consisted of a dispersion coil (DC), a precipitate formation coil (PFC), a precipitate dissolving coil (PDC), and extraction coil (EC). A calibration can be constructed by using a standard iodine solution for dissolved oxygen. The calibration graph was linear over the range 1.2×10⁻⁴∼6.0×10⁻⁴ mol l⁻¹ iodine (1.96∼9.80 mg O l⁻¹)). The relative standard deviation (n=6) was below 0.3% for the 4×10⁻⁴ mol l⁻¹ iodine (6.27 mg O l⁻¹) determination. The sample throughput was 12/h.     

Selective stopped-flow sequential injection method for the spectrophotometric determination of titanium in dental implant and natural Moroccan phosphate rock

The present work reports the first sequential injection (SI) method for the spectrophotometric determination of Ti(IV). The method is based upon the reaction of Ti(IV) with chromotropic acid (CA) in acidic medium to form a water-soluble complex (λ_max = 420 nm). The chemical and instrumental variables of the system that affected the reaction were studied. Selectivity was greatly enhanced using ascorbic acid. A linear calibration graph was obtained in the range 0.2-10.0 mg l⁻¹ Ti(IV) at a sampling frequency of 24 h⁻¹. The precision was satisfactory (s_r = 1.5% at 5.0 mg l⁻¹ Ti(IV), n = 12) and the 3σ limit of detection, c_L, was 0.7 mg l⁻¹ (n = 10). The developed method proved to be adequately selective and was applied successfully to the analysis of real samples (dental implant and natural Moroccan phosphate rock) giving accurate results based on recovery studies (98-105%).