Extraction—spectrophotometric determination of cadmium with diphenylcarbazone in the presence of 1,10-phenanthroline

The addition of 1,10-phenanthroline improves both the extraction and the spectrophotometric sensitivity of the determination of cadmium with diphenylcarbazone. Slope analysis suggests the formation of a 1:2:2 extracted species. The molar absorptivity is 9.4 × 10⁴ l cm^-1 mol^-1 at 536 nm and extraction is maximal at pH 8.2–9.8. Extraction is rapid and absorbances remain constant at room temperature for 48 h. Various divalent metal ions interfere.     

Dual-wavelength spectrophotometric determination of cadmium with cadion

Cadmium has been determined by dual-wavelength spectrophotometry with cadion, p-nitrobenzenediazoaminobenzene-p-azobenzene, and a non-ionic surfactant, Triton X-100. Cadion and its cadmium chelate are dissolved in a micellar solution of the surfactant. The absorbance difference at the wavelength of maximum absorption of the cadmium chelate (477 nm) and that of cadion (566 nm) is measured. A combination of triethanolamine, iminodiacetate and citrate is very effective for masking other ions. Cadmium in zinc metal can be determined without prior separation.     

Indirect spectrophotometric determination of palladium using 1,10-phenanthroline as reagent

Summary The spectrophotometric method for the determination of palladium is based upon the addition of a standard 1,10-phenanthroline solution to precipitate Pd(phen)Cl₂ and the determination of 1,10-phenanthroline concentration of the supernatant solution. The absorbancy readings were made in the absorption maximum at about 271 nm, in the concentration range of 10^–6 to 10^–5M 1,10-phenanthroline in 0.1 M hydrochloric acid and 0.1% hydroxylamine hydrochloride. For the phenanthroline system Beer's law is valid. Ions which either form with phenanthroline very strong complexes or interfere with the spectrophotometric determination of 1,10-phenanthroline must be absent. The method is simple, rapid, accurate and applicable to the macro and micro-determination of palladium in different systems. Standard deviation was found to be 0.085 ppm (in pure Pd solutions).

---

Indirekte spektrophotometrische Bestimmung von Palladium mit 1,10-Phenanthrolin

Zusammenfassung Das Verfahren beruht auf der Fällung von Pd(phen)Cl₂ durch Zusatz einer bestimmten Menge Standard-1,10-Phenanthrolinlösung und spektrophotometrischer Bestimmung des Überschusses.Die Messungen werden bei dem Absorptionsmaximum bei etwa 271 nm und einer Konzentration von 10^–6M bis 10^–5M 1,10-Phenanthrolin in 0,1 M HCl und 0,1% Hydroxylaminhydrochlorid enthaltender Lösung durchgeführt. Das 1,10-Phenanthrolinsystem folgt dem Beerschen Gesetz. Ionen, die entweder mit 1,10-Phenanthrolin starke Komplexe bilden oder die spektrophotometrische Bestimmung von 1,10-Phenanthrolin beeinflussen, müssen abwesend sein. Die Methode ist einfach, rasch und genau und kann für Mikro- und Makrobestimmungen in verschiedenen Systemen angewendet werden. Die Standardabweichung beträgt 0,085 ppm (in reinen Pd-Lösungen).

     

Liquid-liquid extraction and spectrophotometric determination of cadmium with 1,10-phenanthroline and thymol blue

A simple and highly sensitive extraction spectrophotometric method was developed for the determination of traces of cadmium. The method is based on the preconcentrative extraction of ternary-ion-association complex of cadmium—1,10-phenanthroline-thymol blue into chloroform and subsequent determination by spectrophotometry. The ternary ion associate is stable for 20 h and cadmium content as low as 0.1 g in 90 ml of sample can be determined. The method is precise and has been applied to the determination of cadmium in sea water, solder and high purity zinc and indium materials.     

The spectrophotometric determination of thallium(iii)by ternary complex formation

If thallium(III) is added to an aqueous solution of potassium thiocyanate containing a large amount of pyridine in the pH range 5.2–5.5, a yellow solution which is stable in diffuse light is obtained. The yellow colour can be measured at 405 nm for the colorimetric determination of thallium(III) in the range 20–300 μg Tl ml^-1. The complex is a mixed ligand complex with a metal-ligand ratio of 1:2:2. Thallium(I) does not interfere. The interference of various other metal ions and anions is discussed.     

熔融萘萃取铁(Ⅱ)-4,7-二苯基-1,10-菲啰啉-四苯硼酸盐三元络合物光度法测定铁

研究了以熔融萘作为萃取剂,以4,7 二苯基 1,10 菲口罗啉作为显色剂,测定天然水中微量铁的分光光度法。在pH4的条件下,铁(Ⅱ)与4,7 二苯基 1,10 菲口罗啉和四苯硼酸盐能够形成红色三元络合物。在熔融萘存在下,此络合物可以迅速萃入熔融萘。将含有络合物的萘冷却、固化、分离,配制成25mL丙酮溶液,对其进行分光光度分析。实验表明,该络合物最大吸收波长为534nm,摩尔吸光系数和桑德尔灵敏度分别为2×104L·mol-1·cm-1和0.0025μg/cm2,铁(Ⅱ)的质量浓度在0～2 0μg/mL的范围内符合比耳定律。大多数常见离子不干扰测定。已应用于天然水中微量铁的测定。     

Application of redox reactions in spectrophotometry-II Detection and spectrophotometric determination of phenolic compounds with the iron(III)/1,10-phenanthroline complex

To test the utility of the iron(III)/1,10-phenanthroline reagent system for the determination of organic compounds, its reaction with phenolic compounds has been characterized. By a redox reaction the reagent forms the chelate [Fe(phen)(3)](2+), which is extractable as ion-association complexes. Determinations based on these complexes are very sensitive.     

Spectrophotometric determination of vanadium with 1,10-phenanthroline

A simple and sensitive spectrophotometric method for the determination of vanadium based upon the reaction of vanadate with 1,10-phenanthroline in the presence of sodium dithionite in ammoniacal solution is described. The absorbance of the complex measured at 645 nm follows Beer's law for solutions containing 30-400 microg of vanadium in 100 ml of solution. A 10-fold excess of molybdenum, tungsten, phosphorus or chromium does not interfere. The molar absorptivity is 8.0 x 10(3) 1 mole(-1) cm(-1). The complex is shown to be tris-1,10-phenanthroline vanadium(II). The method has been applied successfully to the determination of vanadium in bauxite.     

Simple and rapid spectrophotometric determination of iron after preconcentration as its 1,10-phenanthroline complex on the natural polymer "chitin"

Preconcentration by collection of metal complexes on chitin has been applied to the spectrophotometric determination of iron in water. The iron is collected as its 1,10-phenanthroline (phen) complex on a column of chitin in the presence of tetraphenylborate as counter-ion. The iron(II)-phen complex retained on the chitin is eluted with an acetone-1M acetic acid mixture (8:2 v/v), and the absorbance of the eluate is measured at 512 nm. Beer's law is obeyed over the concentration range 1.1-11.2 mug of iron in 10 ml of eluate. In the presence of EDTA as masking agent, Ca, Mg, Al, Mn, Zn, Cd and Pb do not interfere in concentrations up to 100 times that of iron(II) and Co, Ni and Cu do not interfere in concentrations up to 20 times that of iron(II). Common inorganic anions do not interfere in concentrations up to 10,000 times that of iron(II). The proposed method has been applied to determination of iron in tap water.     

Comprehensive studies on the DNA-binding and cleavage properties of a nickel complex derived from phthalate and 1,10-phenanthroline

Binding properties of a nickel complex, [Ni(phen)(pha)(H₂O)₃] (phen = 1,10-phenanthroline, pha = o-phthalate) to DNA were comprehensively investigated by electronic absorption spectroscopy, viscosity, electrochemistry, melting temperature and gel electrophoresis measurements. After interaction with DNA, the hypochromism and bathochromism for the characteristic absorption peaks of [Ni(phen)(pha)(H₂O)₃] revealed a typical intercalation, which was proved by viscosity and melting temperature experiments. Electrochemical assays showed that the electrochemical activity of the nickel complex was shielded after inserting into the double-helix structure of DNA. Moreover, the results of agarose gel electrophoresis showed that the complex had moderate cleavage ability to supercoiled DNA in the presence of H₂O₂.     

Extraction and spectrophotometric determination of nickel with 2-hydroxyacetophenone oxime and simultaneous determination of copper and nickel

It is observed that 2-hydroxyacetophenone oxime can be used for the quantitative extraction of nickel in the pH range 6.6-7.8 into methyl isobutyl ketone. The organic layer shows maximum absorbance at 375 nm. Beer's law is obeyed over the range 1-6 ppm. The colour of the organic layer is stable for more than 48 hr. Interferences have been studied and methods are suggested for their elimination. Copper and nickel are both quantitatively extracted at pH 7 and can be determined simultaneously and accurately in the range 1-6 microg/ml for copper and 1-4 microg/ml for nickel.     

铒(Er)-L-组氨酸-邻菲啰啉三元配合物的合成与性质

在乙醇介质中,合成了铒(Er)-组氨酸(L-His)-邻菲啰啉(Phen.H2O)三元稀土配合物,利用摩尔电导率、络合滴定分析、元素分析、红外光谱(IR)和热重-差热(TG-DTA)等分析测试,推测配合物的化学组成为:[Er(L-His)3Phen]Cl3.3H2O。初步研究了配合物的电化学性质和生物活性;其中稀土配合物对革兰氏阴性菌大肠杆菌、革兰氏阳性枯草芽孢杆菌都有较好的抑制作用,特别是对革兰氏阴性菌大肠杆菌抑制效果更好。并通过循环伏安测定了配合物在铂盘工作电极上的电化学行为,在HAc-NaAc缓冲溶液(pH≈6.0)中ErCl3.6H2O和配合物{[Er(L-His)3Phen]Cl3.3H2O}在-0.3 V～-1.0 V(vs.SCE)电位范围内均表现出电化学活性,配合物的电化学活化中心是Er3+,该配合物为准可逆体系,且配合物的还原峰电流与浓度和扫描速率呈现递增关系。     

Extraction spectrophotometric determination of cobalt and nickel using ethylthioxanthate

A spectrophotometric method for the determination of cobalt and nickel using a new reagent sodium ethylthioxanthate has been described. The yellow-colored cobalt complex and red-colored nickel complex have been extracted quantitatively using carbon tetrachloride in the pH ranges 4.0–11 and 4.0–6.7, respectively. The colors of these complexes are stable and absorbances have been measured at 389 nm for cobalt and 495 nm for the nickel complexes. Few ions interfere but the method has been applied successfully for the determination of these metal ions in various complex materials.     

Complex formation of rare-earth elements with 1,10-phenanthroline

Complex formation in a Ln(III)-1,10-phenanthroline-ethyl acetate system, where Ln = La, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Yb, or Lu, is studied by spectrophotometric methods. The stability of the complexes is estimated. The changes in the thermodynamic parameters of complex formation and the bonding character in the lanthanide complexes with 1,10-phenanthroline and 2,2′-dipyridyl are ascertained and compared.     

Spectral properties and analytical application of the ternary complex of lanthanum(III) with 1,10-phenanthroline and eosin

The pink lanthanum—(1,10-phenanthroline)₂—(eosin)₂ complex is used to determine 0.5–10 × 10^-5 M lanthanum, either in aqueous solution or chloroform. In the presence of EDTA, only aluminium and cyanide interfere.     

Activation of a 1,10-phenanthroline ligand on a rhenium tricarbonyl complex

The reactions of complex [Re(PPh(2))(CO)(3)(phen)] with either methyl acrylate or methyl propiolate afford products in which the phen ligand has been activated.     

Dynamics of ternary complex formation in the reaction of diaquoanthranilato-N,N-diacetatonickelate(II) with 2,2′-bipyridine and 1,10-phenanthroline

Dynamics of ternary complex formation in the reaction of diaquoanthranilato-N, N-diacetatonickelate(II) with 2,2′-bipyridine and 1,10-phenanthroline. $\rm Ni(ada)(H_2O)_2^{-}$ $+$ $L\rightleftharpoons Ni(ada)(L)^{-}$ $+$ $2 H_20;$ $- {{d[Ni(ada)^{-}]}\over{dt}}$ $=$ $k_f[Ni(ada)^{-}][L]+k_d\ [Ni(ada)(L)];$ $\ ada^{3-}=$anthranilate-N, N-diacetate; and L=bipy or phen. The kinetics of formation of ternary complexes by diaquoanthranilato-N, N-diacetatonickelate(II). [Ni(ada)(H₂O)]⁻ with 2,2′-bipyridine (bipy) and 1,10-phenanthroline (phen) have been studied under pseudo-first-order conditions containing excess bipy or phen by stopped-flow spectrophotometry in the pH range 7.1–7.8 at 25°C and λ = 0.1 mol dm⁻³. In each case, the reaction is first-order with respect to both Ni(ada)⁻ and the entering ligand (ie., bipy, phen). The reactions are reversible. The forward rate constants are: $k^{\rm Ni(ada)}_{\rm Ni(ada)(bipy)}=0.87\times10^3{\rm dm}^3 {\rm mol}^{-1}{\rm s}^{-1}$, . $k^{\rm Ni(ada)}_{\rm Ni(ada)(phen)}=1.87\times10^3{\rm dm}^3 {\rm mol}^{-1}{\rm s}^{-1}$; and the reverse rate constants are: $k^{\rm Ni(ada)(bipy)}_{\rm Ni(ada)}=1.0{\rm s}^{-1}$ and $k^{\rm Ni(ada)(phen)}_{\rm Ni(ada)}=2.0{\rm s}^{-1}$. The corresponding stability constants of ternary complex formation are: and , . The observed rate constants and huge drops in stability constants in ternary complex formation agree well with the mechanism in which dissociation of an acetate arm of the coordinated ada³⁻ prior to chelation by the aromatic ligand occurs. The observations have been compared with the kinetics of ternary complex formation in the reaction Ni(ada)⁻ - glycine in which the kinetics involves a singly bonded intermediate, N(ada)((SINGLE BOND)O(SINGLE BOND)N)²⁻ in rapid equilibrium with the reactants followed by a sluggish ring closure step. The reaction with the aromatic ligands conforms to a steady-state mechanism, while for glycine it gets shifted to an equilibrium mechanism. The cause of this difference in mechanistic pathways has been explained. © 1996 John Wiley & Sons, Inc.