Hydrothermal synthesis of ultrathin hexagonal nickel hydroxide nanosheets

Nickel hydroxide, Ni(OH)₂ is widely used in electrodes of nickel-based alkaline secondary batteries. Ultrathin hexagonal Ni(OH)₂ nanosheets of space group P-3m1 were hydrothermally prepared at 200 °C for 10 h. Their diameter and thickness were 200–300 and 3–5 nm, respectively. Their formation was attributed to the oriented assembly of growing particles, which was assisted by surfactant molecules. The specific surface area of the Ni(OH)₂ nanosheets was 8.66 m²/g. Their magnetization curve exhibited linear paramagnetic behavior across the entire measurement region.     

Magnetic and electrochemical behavior of rhombohedral α-Fe2O3 nanoparticles with (1 0 4) dominant facets

Uniform rhombohedral α-Fe₂O₃ nanoparticles, ～60 nm in size, were synthesized via a triphenylphosphine-assisted hydrothermal method. Scanning electron micrograph (SEM) and transmission electron micrograph (TEM) analyses showed that the as-synthesized rhombohedral nanoparticles were enclosed by six (1 0 4) planes. The concentration of triphenylphosphine played an important role in morphological evolution of the α-Fe₂O₃ nanoparticles. The as-prepared rhombohedral nanoparticles possessed remanent magnetization M_r of 2.6 × 10^?3 emu/g and coercivity H_C of 2.05 Oe, both lower than those of other α-Fe₂O₃ particles with similar size, indicating their potential applications as superparamagnetic precursor materials. Furthermore, these rhombohedral α-Fe₂O₃ nanoparticles exhibited good sensor capability toward H₂O₂ with a linear response in the concentration range of 2–20 mM.     

Viscosity of alumina nanoparticles dispersed in car engine coolant

The present paper, describes our experimental results on the viscosity of the nanofluid prepared by dispersing alumina nanoparticles (<50 nm) in commercial car coolant. The nanofluid prepared with calculated amount of oleic acid (surfactant) was tested to be stable for more than 80 days. The viscosity of the nanofluids is measured both as a function of alumina volume fraction and temperature between 10 and 50 °C. While the pure base fluid display Newtonian behavior over the measured temperature, it transforms to a non-Newtonian fluid with addition of a small amount of alumina nanoparticles. Our results show that viscosity of the nanofluid increases with increasing nanoparticle concentration and decreases with increase in temperature. Most of the frequently used classical models severely under predict the measured viscosity. Volume fraction dependence of the nanofluid viscosity, however, is predicted fairly well on the basis of a recently reported theoretical model for nanofluids that takes into account the effect of Brownian motion of nanoparticles in the nanofluid. The temperature dependence of the viscosity of engine coolant based alumina nanofluids obeys the empirical correlation of the type: log (μ_nf) = A exp(BT), proposed earlier by Namburu et al.     

Green synthesis and enhanced photocatalytic activity of Ce-doped TiO2 nanoparticles supported on porous glass

A facile and green method to prepare Ce-doped TiO₂ nanoparticles supported on porous glass beads is reported. An ion exchange process and subsequent calcination yielded Ce-doped TiO₂ nanoparticles with a mean size of 4.8 ± 0.3 nm. The nanoparticles were dispersed on the surface of porous glass beads. The addition of Ce enhanced the visible light absorption of the TiO₂ nanoparticles in the 400–500 nm spectral window. The band gap of the as-prepared catalyst was 2.80 eV. The Ce-doped TiO₂ nanoparticles immobilized on porous glass beads exhibited excellent photocatalytic activity for the visible-light-degradation of methyl orange (MO) and rhodamine B (RhB); with rate constants of 0.095 and 0.230 min⁻¹; respectively. The effects of Ce dosage; reaction duration; and initial solution pH on the conversion of MO and RhB dyes were investigated. The green synthesis and favorable photocatalytic activity makes the Ce-doped TiO₂ nanoparticles immobilized on porous glass an attractive alternative for the efficient degradation of organic pollutants.     

Capuli cherry-mediated green synthesis of silver nanoparticles under white solar and blue LED light

In this article, the Capuli (Prunus serotina Ehrh. var. Capuli) cherry extract was used for the synthesis of silver nanoparticles (AgNPs) in the presence of white/visible solar and blue light-emitting diode (LED) light. For the characterization of the extract and the AgNPs, Fourier transform infrared spectroscopy and ultraviolet–visible spectroscopy were employed, along with hydrodynamic particle size analysis, transmission electron microscopy and X-ray diffraction. The Ag nanospheres obtained using white light were 40–100 nm in diameter and exhibited an absorption peak at λ_max = 445 nm, whereas those obtained using blue LED light were 20–80 nm in diameter with an absorption peak at λ_max = 425 nm. Thermal analysis revealed that the content of biomolecules surrounding the AgNPs was about 55–65%, and it was also found that blue LED light AgNPs (56.28%, 0.05 mM) had a higher antioxidant efficacy than the white solar light AgNPs (33.42%, 0.05 mM) against 1,1-diphenyl-2-picrylhydrazyl. The results indicate that obtaining AgNPs using a blue LED light may prove to be a simple, cost-effective and easily reproducible method for creating future nanopharmaceuticals.     

Effect of calcining temperature and time on the characteristics of Sb-doped SnO2 nanoparticles synthesized by the sol–gel method

Spherical Sb-doped SnO₂ (ATO) nanoparticles were synthesized by the sol–gel route, employing SnCl₄·5H₂O and SbCl₃ as precursors in an ethanol solution. The influences of the calcining temperature and calcining time on the crystallite size, crystallinity, lattice parameters, lattice distortion ratio and the resistivity of the ATO nanoparticles were synthetically investigated. The results suggested that the ATO nanoparticles were crystallized in a tetragonal cassiterite structure of SnO₂ with a highly (1 1 0)-plane-preferred orientation. The calcining temperature had a dominating effect on the crystallite size, crystallinity, lattice distortion ratios and resistivity of the ATO. As the calcining temperature increased, the average crystallite size increased, the crystallinity was promoted accompanied by a decrease in the lattice distortion ratio and a corresponding decrease in the resistivity of the ATO. X-ray diffraction (XRD) and Fourier transform infrared spectrophotometer (FTIR) analysis revealed that Sb ions could not entirely supplant the Sn ions in the SnO₂ lattice for a calcining time of less than 0.5 h, even at a calcining temperature of 1000 °C. The ATO nanoparticles calcined at 1000 °C for 3.0 h possessed the lowest resistivity of 10.18 Ω cm.     

Solvent-less synthesis of zinc oxide nanostructures from Zn(salen) as precursor and their optical properties

ZnO nanoparticles, 10–20 nm in size, were synthesized by heat treatment in air at 500 °C for 5 h., using [N,N′-bis(salicylaldehydo) ethylene diamine]zinc(II), i.e., Zn(salen), as precursor, which was obtained by a solvent-free solid–solid reaction. Heat-treated products were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy. Room temperature photoluminescence spectra of ZnO nanostructures are dominated by green emission attributed to oxygen vacancy related donor–acceptor transition.     

A novel method for fast and continuous preparation of superfine titanium dioxide nanoparticles in microfluidic system

Previously we had developed a microfluidic system that can be easily fabricated by bending a stainless-steel tube into large circular loops. In this study, a fast and continuous preparation method for superfine TiO₂ nanoparticles (TiO₂-NPs) was developed for the aforementioned microfluidic system. The proposed method can yield anatase TiO₂ in 3.5 min, in contrast to the traditional hydrothermal reaction method, which requires hours or even days. Different reaction conditions, such as reaction temperature (120–200 °C), urea concentration (20–100 g/L), and tube length (5–20 m) were investigated. X-ray diffraction and Brunauer–Emmett–Teller analysis indicate that the as-prepared TiO₂-NPs have crystalline sizes of 4.1–5.8 nm and specific surface areas of 250.7–330.7 m²/g. Transmission electron microscopy images show that these TiO₂-NPs have an even diameter of approximately 5 nm. Moreover, because of their small crystalline sizes and large specific surface areas, most of these as-prepared TiO₂-NPs exhibit considerably better absorption and photocatalytic performance with methylene blue than commercial P5 TiO₂ does.     

Highly dispersed Mn2O3 microspheres: Facile solvothermal synthesis and their application as Li-ion battery anodes

Nanostructured transition metal oxides are promising alternative anodes for lithium ion batteries. Li-ion storage performance is expected to improve if high packing density energy particles are available. Herein, Mn₂O₃ microspheres with a ca. 18 μm diameter and a tapped density of 1.33 g/cm³ were synthesized by a facile solvothermal–thermal coversion route. Spherical MnCO₃ precursors were obtained through solvothermal treatment and they decomposed and converted into Mn₂O₃ microspheres at an annealing temperature of 700 °C. The Mn₂O₃ microspheres consisted of Mn₂O₃ nanoparticles with an average 40 nm diameter. These porous Mn₂O₃ microspheres allow good electrolyte penetration and provide an ion buffer reservoir to ensure a constant electrolyte supply. The Mn₂O₃ microspheres have reversible capacities of 590 and 320 mAh/g at 50 and 400 mA/g, respectively. We thus report an efficient route for the fabrication of energy particles for advanced energy storage.     

Fabrication of nano-sized Ca(OH)2 with excellent adsorption ability for N2O4

Uniform nano-sized calcium hydroxide (Ca(OH)₂) monocrystal powder was synthesized from calcium oxide in a surfactant solution via a digestion method by decreasing the surface tension of the reaction system to control the growth of crystalline Ca(OH)₂. The Ca(OH)₂ monocrystal powder samples were characterized by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), and Fourier transform-infrared spectroscopy (FT-IR). The NO_x adsorption ability of the samples was evaluated, and the influence of various types and concentrations of surfactants on powder agglomeration and then the specific surface area in the precipitation process were studied. The specific surface area of the samples was found as high as 58 m²/g and 92 m²/g and the particle size, 300–400 nm and 200–300 nm in the presence of 10 wt% PEG600 and 0.086 mL/L SDS at a reaction time of 5 h, respectively. The product has an exceptionally strong adsorption ability for NO_x, which makes it a highly promising adsorbent for emission control and air purification.     

Large-scale synthesis of hierarchical MnO2 for benzene catalytic oxidation

Hierarchical sea-urchin-shaped manganese oxide microspheres were synthesized via a facile method based on the reaction between KMnO₄ and MnSO₄ in HNO₃ solution at 50 °C. The average diameter of the microspheres is ∼850 nm. The microspheres consist of a core of diameter of ∼800 nm and nanorods of width ∼50 nm. The nanorods exist at the edge of the core. The Brunauer–Emmett–Teller surface area of the sea-urchin-shaped microspheres is 259.4 m²/g. A possible formation mechanism of the hierarchical sea-urchin-shaped microspheres is proposed. The temperature for 90% conversion of benzene (T_90%) on the hierarchical urchin-shaped MnO₂ microspheres is about 218 °C.     

Preparation of SiO2/TiO2 Janus particles by electrostatic assembly,hydrolysis and calcination

This paper describes a novel chemical method for preparing SiO₂/TiO₂ Janus particles. First, polystyrene (PSt)/SiO₂ particles with a raspberry-like structure are prepared by electrostatic assembly. The influences of the reaction time of sulfonation and the treatment times of polyelectrolyte solutions (PDADMAC, PSS) on PSt and SiO₂ are investigated with respect to the surface charge density of the particles. SiO₂/TiO₂ Janus particles are then obtained by hydrolysis of butyl titanate on the surface of PSt/SiO₂ particles followed by a calcination process. Particle size analyzer, Zeta potential instrument, FTIR, TEM and SEM are used to characterize the particle size, the amount of charge on the surface of PSt and SiO₂ particles and the compositions and morphologies of PSt/SiO₂, SiO₂/TiO₂ and PSt/SiO₂/TiO₂. The diameters of the PSt, SiO₂, PSt/SiO₂ and SiO₂/TiO₂ particles are 2.0 μm, 303 nm, 2.7 μm and 330 nm, respectively.     

Experimental studies on heat transfer and friction factor characteristics of Al2O3/water nanofluid in a circular pipe under laminar flow with wire coil inserts

In this paper, fully developed laminar flow convective heat transfer and friction factor characteristics of Al₂O₃/water nanofluid flowing through a uniformly heated horizontal tube with and without wire coil inserts is presented. For this purpose, Al₂O₃ nanoparticles of 43 nm size were synthesized, characterized and dispersed in distilled water to form stable suspension containing 0.1% volume concentration of nanoparticles. The Nusselt number in the fully developed region were measured and found to increase by 12.24% at Re = 2275 for plain tube with nanofluid compared to distilled water. Two wire coil inserts made of stainless steel with pitch ratios 2 and 3 were used which increased the Nusselt numbers by 15.91% and 21.53% respectively at Re = 2275 with nanofluid compared to distilled water. The better heat transfer performance of nanofluid with wire coil insert is attributed to the effects of dispersion or back-mixing which flattens the temperature distribution and make the temperature gradient between the fluid and wall steeper. The measured pressure loss with the use of nanofluids is almost equal to that of the distilled water. The empirical correlations developed for Nusselt number and friction factor in terms of Reynolds/Peclet number, pitch ratio and volume concentration fits with the experimental data within ±15%.     

Synthesis of layered cathode materials Li[CoxNiyMn1−x−y]O2 from layered double hydroxide precursors

Cathode materials Li[Co_xNi_yMn_1?x?y]O₂ for lithium secondary batteries have been prepared by a new route using layered double hydroxides (LDHs) as a precursor. The resulting layered phase with the α-NaFeO₂ structure crystallizes in the rhombohedral system, with space group R-3m having an interlayer spacing close to 0.47 nm. X-ray photoelectron spectroscopy (XPS) was used to measure the oxidation states of Co, Ni and Mn. The effects of varying the Co/Ni/Mn ratio on both the structure and electrochemical properties of Li[Co_xNi_yMn_1?x?y]O₂ have been investigated by X-ray diffraction and electrochemical tests. The products demonstrated a rather stable cycling behavior, with a reversible capacity of 118 mAh/g for the layered material with Co/Ni/Mn = 1/1/1.     

Synthesis of mesoporous γ-AlOOH@Fe3O4 magnetic nanomicrospheres

Mesoporous γ-AlOOH@Fe₃O₄ magnetic nanomicrospheres were synthesized using superparamagnetic Fe₃O₄ nanoparticles as the core and aluminum isopropoxide (AIP) as the aluminum source. The obtained magnetic nanomicrospheres were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), N₂ adsorption–desorption and vibrating sample magnetometry (VSM). The effects of preparation parameters such as hydrolysis time of AIP, concentration of AIP and coating layer number on microspheres were investigated. The results indicated that the mesoporous γ-AlOOH@Fe₃O₄ magnetic nanomicrospheres consisted of a mesoporous γ-AlOOH shell and a Fe₃O₄ magnetic core. The diameter of γ-AlOOH@Fe₃O₄ nanomicrospheres was about 200 nm, the thickness of mesoporous γ-AlOOH shell was about 5 nm and the average pore size was 3.8 nm. The thickness of the mesoporous γ-AlOOH shell could be controlled via layer-by-layer coating times. The formation mechanism of the mesoporous γ-AlOOH shell involved a “chemisorption–hydrolysis” process.     

An experimental study of circular sand–water wall jets

Laboratory experiments were carried out to study the effects of sand particles on circular sand–water wall jets. Mean and turbulence characteristics of sand particles in the sand–water wall jets were measured for different sand concentrations c_o ranging from 0.5% to 2.5%. Effects of sand particle size on the centerline sand velocity of the jets were evaluated for sand size ranging from 0.21 mm to 0.54 mm. Interesting results with the range of measurements are presented in this paper. It was found that the centerline sand velocity of the wall jets with larger particle size were 15% higher than the jets with smaller particle size. Concentration profiles in the vertical direction showed a peak value at x/d = 5 (where x is the longitudinal distance from the nozzle and d is the nozzle diameter) and the sand concentration decreased linearly for x/d > 5. Experimental results showed that the turbulence level enhanced from the nozzle to x/d = 10. For sand–water wall jets with a higher concentration (c_o = 1.5–2.5%), the turbulence intensity became smaller than the corresponding single-phase wall jets by 34% due to turbulent modulation. A modified logarithmic formulation was introduced to model the longitudinal turbulent intensity at the centerline and along the axis of the jet.     

Effect of temperature on the effective thermal conductivity of n-tetradecane-based nanofluids containing copper nanoparticles

Nanofluids were prepared by dispersing Cu nanoparticles (∼20 nm) in n-tetradecane by a two-step method. The effective thermal conductivity was measured for various nanoparticle volume fractions (0.0001–0.02) and temperatures (306.22–452.66 K). The experimental data compares well with the Jang and Choi model. The thermal conductivity enhancement was lower above 391.06 K than for that between 306.22 and 360.77 K. The interfacial thermal resistance increased with increasing temperature. The effective thermal conductivity enhancement was greater than that obtained with a more viscous fluid as the base media at 452.66 K because of nanoconvection induced by nanoparticle Brownian motion at high temperature.     

Effects of multi-dopants (Zn and Ho) in stabilizing spinel structure for cathode materials in lithium rechargeable batteries—Novel chelated sol–gel synthesis

Multi-doped spinels, namely LiMn₂O₄ and LiZn_xHo_yMn_2−x−yO₄ (x = 0.10–0.18; y = 0.02–0.10), for use as cathode materials for lithium-ion rechargeable batteries were synthesized via sol–gel method, using lauric acid as the chelating agent, to obtain micron-sized particles. The physical properties of the synthesized samples were investigated using differential thermal analysis, Fourier-transform infrared spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy, energy-dispersive X-ray analysis, and electrochemical methods. XRD showed that LiMn₂O₄ and LiZn_xHo_yMn_2−x−yO₄ have high degrees of crystallinity and good phase purities. The SEM images of LiMn₂O₄ showed an ice-cube morphology with particles of size 1 μm. Charge–discharge studies showed that undoped LiMn₂O₄ delivered the discharge capacity of 124 mA h/g with coulombic efficiency of 95% during the first cycle, whereas doped spinels delivered discharge capacities of 125, 120, and 127 mA h/g in the first cycle with coulombic efficiencies of 96%, 91%, and 91%, respectively.     

Thermo-mechanical behaviour of TRIP 1000 steel sheets subjected to low velocity perforation by conical projectiles at different temperatures

This paper presents and analyzes the behaviour of TRIP 1000 steel sheets subjected to low velocity perforation by conical projectiles. The relevance of this material resides in the potential transformation of retained austenite to martensite during impact loading. This process leads to an increase in strength and ductility of the material. However, this transformation takes place only under certain loading conditions strongly dependent on the initial temperature and deformation rate. In order to study the material behaviour under impact loading, perforation tests have been performed using a drop weight tower. Experiments were carried out at two different initial temperatures T₀ = 213 K and T₀ = 288 K, and within the range of impact velocities 2.5 m/s ? V₀ ? 4.5 m/s. The experimental setup enabled the measuring of impact velocity, residual velocity, load-time history and failure mode. In addition, dry and lubricated contacts between the striker and the plate have been investigated. Finally, by using X-ray diffraction it has been shown that no martensitic transformation takes place during the perforation process. The causes involving the none-appearance of martensite are examined.     

Irbesartan drug formulated as nanocomposite particles for the enhancement of the dissolution rate

Irbesartan (IBS), an angiotensin II receptor antagonist, is a poorly water-soluble drug. To enhance the dissolution rate, IBS nanocomposite particles were produced via an anti-solvent precipitation combined with a spray drying process. Four pharmaceutically acceptable excipients, including three different polymers and one charged surfactant, were evaluated as stabilizers to control the particle size and to prevent the agglomeration of particles. The experiment results indicated that polyvinylpyrrolidone (PVP) combined with sodium dodecyl sulfate (SDS) significantly decreased the particle size and enhanced the stability of drug nanoparticles. As a result, we finally obtained stable IBS nanoparticles with an average size of approximately 55 nm. In the dissolution test, the IBS nanocomposite particles showed a significantly enhanced dissolution rate and 100% of the drug dissolved within 20 min. In contrast, the physical mixture with the same recipe as the IBS nanocomposite particles and the raw IBS reached only 8% and 40% of drug dissolved in 20 min, respectively, and both of them did not dissolve completely, even after 120 min.